The transition from As-doped GaN, showing blue emission, to GaNAs alloys in films grown by molecular beam epitaxy

We have studied the transition from As-doped GaN showing strong blue emission (2.6 eV) at room temperature to the formation of GaN_1−xAs_x alloys for films grown by plasma-assisted molecular beam epitaxy. We have demonstrated that with increasing N-to-Ga ratio there is first an increase in the intensity of blue emission at about 2.6 eV and then a transition to the growth of GaN_1−xAs_x alloy films. We present a model based on thermodynamic considerations, which can explain how this might occur.     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

Correlations between photoluminescence and Hall mobility in GaN/sapphire grown by metalorganic chemical vapor deposition

We have investigated photoluminescence (PL) and electron Hall mobility for unintentionally doped GaN epitaxial layers grown by low-pressure metalorganic chemical vapor deposition on c-plane Al₂O₃ substrates. Four GaN films having identical dislocation density but remarkably different electron Hall mobility were exploited. At low temperature (12 K), a PL line associated with a bound exciton was observed and strong correlations were found between the Hall mobility and the PL intensity of the exciton transition. That is, relative PL intensity of the bound exciton to a donor-bound exciton monotonously increased with decreasing the electron mobility of the GaN films. This correlation was interpreted in terms of electrical compensation. Efforts to find the chemical origin of the PL line led to the conclusion that the BE line originated neither from threading dislocations nor from extrinsic point defects. Intrinsic acceptors such as Ga vacancy and GaN anti-site were suspected as plausible origin.     

Synthesis and optical properties of Ce-doped ZnO hexagonal nanoplatelets

Single crystalline Ce-doped ZnO hexagonal nanoplatelets are successfully synthesized. Zinc acetate, cerium nitrate, potassium hydroxide and poly vinyl alcohol were mixed together and transferred to a 100 mL Teflon-lined stainless steel autoclave kept at 150 °C for 24 h. The obtained precipitant is calcined at 600 °C. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. The investigation confirmed that the products were of the wurtzite structure of ZnO. The doped hexagonal nanoplatelets have edge length 25 nm and thickness 11 nm. EDX result showed that the amount of Ce in the product is about 15%. Photoluminescence of these doped hexagonal nanoplatelets exhibits a blue shift and weak ultraviolet (UV) emission peak, compared with pure ZnO, which may be induced by Ce-doping. The growth mechanism of the doped hexagonal nanoplatelets was also discussed.     

Optimization of hydrothermal growth ZnO Nanorods for enhancement of light extraction from GaN blue LEDs

In this study, we report on the enhancement in the light extraction efficiency of GaN blue LEDs topped with ZnO nanorods. The ZnO nanorods were grown by a two-step hydrothermal synthesis with pre-coated ZnO nanoparticles under optimized condition to give the appropriate size and quality, giving an increase in the light output efficiency of 66%. This improvement is attributed to the optimal rod size and spacing with improved thermal dissipation as compared to light extraction from plain GaN surface. During the ZnO growth on the LEDs, 0.55 M of NH₃ was added and the ZnO sample was later annealed at 475 °C in N₂ ambient, to drive out interstitial oxygen atoms from the tetrahedral unstable site. As a result, a high ratio of UV to orange defect band emission was achieved. The two-step growth of ZnO nanorods on GaN LEDs was effective in generating array of ZnO nanorods which serve as reflector to enhance light extraction from LEDs.     

Profiling band structure in GaN devices by electron holography

Electron holography in a field emission gun transmission electron microscope has been used to profile the inner potential V₀ across GaN/x nm In_0.1Ga_0.9N/GaN/(0 0 0 1) sapphire samples (x=10, 40 nm) grown by molecular beam epitaxy and viewed in cross-section. Results are presented which suggest a decrease in V₀ of 3–4 V across the InGaN layer in the [0 0 0 1] direction. It is proposed that the results can be explained by charge accumulation across the InGaN layer and that the opposing contributions due to piezoelectric and polarisation fields are effectively masked by Fermi level pinning.     

HRTEM investigation of high-reflectance AlN/GaN distributed Bragg-reflectors by inserting AlN/GaN superlattice

A high-quality AlN/GaN distributed Bragg-reflectors (DBR) was successfully grown on sapphire substrate by low-pressure metal-organic chemical vapor deposition using ultra-thin AlN/GaN superlattice insertion layers (SLILs). The reflectivity of AlN/GaN DBR with ultra-thin AlN/GaN SLIL was measured and achieved blue peak reflectivity of 99.4% at 462 nm. The effect of ultra-thin AlN/GaN superlattice insertion layer was examined in detail by transmission electron microscopy, and indicated that the crack of AlN/GaN DBR can be suppress by inserting AlN/GaN SLIL. For electronic properties, the turn on voltage is about 4.1 V and CW laser action of vertical-cavity surface-emitting laser (VCSEL) was achieved at a threshold injection current of 1.4 mA at 77 K, with an emission wavelength of 462 nm.     

Reduction of threading dislocations in migration enhanced epitaxy grown GaN with N-polarity by use of AlN multiple interlayer

High quality GaN layer was obtained by insertion of high temperature grown AlN multiple intermediate layers with migration enhanced epitaxy method by the RF-plasma assisted molecular beam epitaxy on (0 0 01) sapphire substrates. The propagating behaviors of dislocations were studied, using a transmission electron microscope. The results show that the edge dislocations were filtered at the AlN/GaN interfaces. The bending propagation of threading dislocations in GaN above AlN interlayers was confirmed. Thereby, further reduction of dislocations was achieved. Dislocation density being reduced, the drastic increase of electron mobility to 668 cm²/V s was obtained at the carrier density of 9.5×10¹⁶ cm⁻³ in Si doped GaN layer.     

Synthesis of GaN nanospindles via a facile solid-state reaction route

Gallium nitride (GaN) nanospindles have been synthesized via a solid-state reaction at a low-temperature condition. X-ray powder diffraction (XRD), Raman spectrum and high-resolution transmission electron microscopy (HRTEM) revealed that the synthesized GaN crystallized in a hexagonal structure and displaying spindly particles morphology has an average diameter of 100 nm and length of 400 nm X-ray photoelectron spectroscopy (XPS) of the sample gave the atomic ratio of Ga and N of 1.04:1. Room-temperature photoluminescence (PL) spectrum showed that the as-prepared product had a peak emission at 372 nm. The possible formation mechanism of the wurtzite GaN is briefly discussed.     

Ammonothermal epitaxy of wurtzite GaN using an NH4I mineralizer

Purely wurtzite phase needle crystals and epitaxial layers of GaN were grown by the ammonothermal method using an NH₄I mineralizer. The inclusion of zincblende phase GaN was effectively eliminated by increasing the growth temperature higher than 500 °C. Accordingly, an approximately 20-μm-thick GaN epitaxial layer was achieved on the Ga-polar face of a c-plane GaN seed wafer at 520 °C. Although the characteristic deep state emission band dominated the room temperature photoluminescence spectrum, the near-band-edge emission of GaN was observed for both the needle crystals and the epitaxial layers. These results encourage one to grow better quality GaN crystals at a high growth rate under high-temperature growth conditions.     

Emission studies of InGaN layers and LEDs grown by plasma-assisted MBE

We prepared InGaN layers on GaN/sapphire substrates using rf-MBE. Photoluminescence (PL) from these layers, grown at different temperatures T_S, shows that there is a strong tendency of GaN to form a separate phase as T_S is increased from 600°C to 650°C. Concomitant with the phase separation, the PL from the InGaN phase broadens, which indicates that indium composition in this phase becomes increasingly non-uniform. Indium compositions measured by Rutherford backscattering (RBS) are consistent with these results. We also observed an increase in PL intensity for InGaN layers grown at higher temperatures. In this paper, we also report on preparing a top-contact InGaN/GaN light emitting diode. The device was operated at 447 nm and had the emission line width of 37 nm with no observable impurity related features. The turn-on voltage was 3.0 V. The output power was 20 μW at 60 mA drive current.     

Polar optical phonon scattering and negative Krömer–Esaki–Tsu differential conductivity in bulk GaN

GaN is being considered as a viable alternative semiconductor for high-power solid-state electronics. This creates a demand for the characterization of the main scattering channel at high electric fields. The dominant scattering mechanism for carriers reaching high energies under the influence of very high electric fields is the polar optical phonon (POP) emission. To highlight the directional variations, we compute POP emission rates along high-symmetry directions for the zinc-blende and wurtzite crystal phases of GaN. Our treatment relies on the empirical pseudopotential energies and wave functions. The scattering rates are efficiently computed using the Lehmann–Taut Brillouin zone integration technique. For both crystal phases, we also consider the negative differential conductivity possibilities associated with the negative effective mass part of the band structure.     

Experimental and theoretical investigations of the electrical properties of undoped and magnesium-doped GaN layers

The ac characteristics of GaN : Mg and undoped GaN layers, grown by MOVPE on sapphire substrates, are measured for a wide range of temperature and bias conditions, in order to investigate the effect of the magnesium-related level on the transport properties. Two peaks, whose height and position depend on the measurement temperature, are observed in the admittance curves (G/ω versus frequency) of the Mg-doped samples, whereas only one peak appears in undoped samples. The study of the frequency dependence of the impedance, with a model including the two metallic Au/GaN junctions, the GaN layer itself, shows that, besides the effect of the differential resistance of the layer which plays a role in both sample types, the presence of a Mg-related deep level contributes to the observed variations of the peaks in the admittance curves of the p-doped samples. Results of a theoretical steady-state and small-signal analysis based on numerical modelling of the Au/GaN/Au heterostructure complete our analysis.     

Characterization of etched facets for GaN-based lasers

Dry-etching of laser facets is commonly used for (InAl)GaN/sapphire-based structures since the epitaxial planes of the nitride layers are rotated with respect to the substrate planes making cleaving impractical. To achieve steep and smooth facets by chemically assisted ion beam etching, a 3-layer resist system is developed for patterning. Characterization by scanning electron microscopy and atomic force microscopy shows facets with root-mean-square roughnesses of 7 nm and inclination angles of 2–4°. Optically pumped lasers yield low threshold excitation densities for fully doped separate confinement heterostructure lasers.     

Microstructure and cathodoluminescence study of GaN nanowires without/with P‐doping

In this work, P‐doped GaN nanowires were synthesized in a co‐deposition CVD process and the effects of P‐doping on the microstructure and cathodoluminescence (CL) of GaN nanowires were studied in details. SEM observation and CL measurments demonstrated that P‐doping has led to a rough morphology evolution and a depression of the band‐gap emission of GaN nanowires, whereas the visible emission of GaN nanowires was obviously enhanced. Finally, the corresponding morphology transition and optical properties of GaN nanowires with P‐doping were discussed. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Dense vertical nanoplates arrays and nanobelts of indium doped ZnO grown by thermal treatment of ZnS–In2O3 powders

Dense vertical arrays of indium doped ZnO nanoplates have been grown by thermal treatment of compacted ZnS–In₂O₃ powders with 0.35 at% of In. The distribution of nanoplates is related to the grain structure of the substrate. Only a small content of In has been detected in the plates by energy dispersive X-ray spectroscopy, but comparison with previous works shows that its presence in the precursor determines the growth of the nanoplates. Increase in the amount of In in the precursor leads to the growth of long indium doped ZnO nanobelts. Cathodoluminescence spectra of the nanobelts show a 23 meV blue shift of the band edge emission.     

Characterization of GaInN/GaN layers for green emitting laser diodes

An enhancement of radiative recombination in GaInN/GaN heterostructures is being pursued by a reduction of defects associated with threading dislocations and a structural control of piezoelectric polarization in the active light-emitting regions. First, in conventional heteroepitaxy on sapphire substrate along the polar c-axis of GaN, green and deep green emitting light-emitting diode (LED) wafers are being developed. By means of photoluminescence at variable low temperature and excitation density, internal quantum efficiencies of 0.18 for LEDs emitting at 530 nm and 0.08 for those emitting at 555 nm are determined. Those values hold for the high current density of 50 A/cm² of high-power LED lamps. In bare epi dies, we obtain efficacies of 16 lm/W. At 780 A/cm² we obtain 22 lm when measured through the substrate only. The 555 nm LED epi material under pulsed photoexcitation shows stimulated emission up to a wavelength of 485 nm. This strong blue shift of the emission wavelength can be avoided in homoepitaxial multiple quantum well (MQW) and LED structures grown along the non-polar a- and m-axes of low-dislocation-density bulk GaN. Here, wavelength-stable emission is obtained at 500 and 488 nm, respectively, independent on excitation power density opening perspectives for visible laser diodes.     

Structural and photoluminescence properties of GaN/ZnO core‐shell nanowires with their shells sputtered

We have reported the preparation of ZnO‐coated GaN nanowires and investigated changes in the structural and photoluminescence (PL) properties by the application of a thermal annealing process. For fabricating the core‐shell nanowires, Zn target was used to sputter ZnO shell onto GaN core nanowires. X‐ray diffraction (XRD) analysis indicated that the annealed core‐shell nanowires clearly exhibited the ZnO as well as GaN phase. The transmissoin electron microscopy (TEM) investigation suggested that annealing has induced the crystallization of ZnO shell layer. We have carried out Gaussian deconvolution analysis for the measured PL spectra, revealing that the core GaN nanowires exhibited broad emission which consist of red, yellow, blue, and ultraviolet peaks. ZnO‐sputtering induced new peaks in the green region. Thermal annealing reduced the relative intensity of the green emission. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Defect reduction in GaN epilayers and HFET structures grown on (0 0 0 1)sapphire by ammonia MBE

The quality of GaN epilayers grown by molecular beam epitaxy on substrates such as sapphire and silicon carbide has improved considerably over the past few years and in fact now produces AlGaN/GaN HEMT devices with characteristics among the best reported for any growth technique. However, only recently has the bulk defect density of MBE grown GaN achieved levels comparable to that obtained by MOVPE and with a comparable level of electrical performance. In this paper, we report the ammonia-MBE growth of GaN epilayers and HFET structures on (0 0 0 1)sapphire. The effect of growth temperature on the defect density of single GaN layers and the effect of an insulating carbon doped layer on the defect density of an overgrown channel layer in the HFET structures is reported. The quality of the epilayers has been studied using Hall effect and the defect density using TEM, SEM and wet etching. The growth of an insulating carbon-doped buffer layer followed by an undoped GaN channel layer results in a defect density in the channel layer of 2×10⁸ cm⁻². Mobilities close to 490 cm²/Vs at a carrier density of 8×10¹⁶ cm⁻³ for a 0.4 μm thick channel layer has been observed. Growth temperature is one of the most critical parameters for achieving this low defect density both in the bulk layers and the FET structures. Photo-chemical wet etching has been used to reveal the defect structure in these layers.     

Bismuth a new dopant for GaN films grown by molecular beam epitaxy—surfactant effects,formation of GaN1−xBix alloys and co-doping with arsenic

We have investigated the influence of an additional bismuth flux during growth on the properties of GaN films prepared by plasma-assisted molecular beam epitaxy (MBE). A wide range of bismuth fluxes have been used, the highest Bi flux was larger than the flux of Ga. We have demonstrated that using a Bi flux during the growth of GaN by MBE at a temperature ∼800°C improves the surface morphology of the films and decreases the deep emission. We have demonstrated for the first time the growth of GaN_1−xBi_x alloys by MBE, the Bi concentration was small and increased with decreasing growth temperature. We have studied the influence of an additional bismuth flux on the growth of As-doped GaN layers and observed an increase of blue emission from the layers at some optimum range of Bi fluxes. All the results allow us to conclude that Bi may be a potential new dopant for the growth of GaN by MBE.