Square Wave‐Anodic Stripping Voltammetric Determination of Copper at a Bismuth Film/Glassy Carbon Electrode Using 3‐[(2‐Mercapto‐Vinyl)‐Hydrazono]‐ 1,3‐Dihydro‐Indol‐2‐One

This study reports a highly sensitive electrochemical sensor based on Bi film modified glassy carbon electrode (BiF/GCE) for total determination and speciation trace concentrations of copper(II) ions in environmental water samples. Square wave‐adsorptive anodic stripping voltammetric (SW‐ASV) experiment was performed for monitoring selective accumulation of copper(II) with reagent 3‐[(2‐mercapto‐vinyl)‐hydrazono]‐1,3‐dihydro‐indol‐2‐one (MHDI) at pH 9–10. The mechanism of the electrode reaction of Cu²⁺‐MHDI complex was safely assigned. The sensor exhibited a wide linear range (3.22×10⁻⁹–2.0×10⁻⁷ mol L⁻¹) with lower limits of detection (LOD) and quantitation (LOQ) of 9.6×1⁻¹⁰ and 3.22×10⁻⁹ mol L⁻¹, respectively (R²=0.9993). The proposed sensor exhibited interference from active metal ions e. g. Cd, Hg. The performance of the proposed method was compared successfully with most of the reported methods and comparable efficiencies were obtained. The analytical utility of the proposed SW‐ASV method has been successfully validated for trace analysis of copper(II) in environmental water samples. The method offers a precise, accurate approach with good reproducibility, robustness, ruggedness, and cost effectiveness.     

The Electrochemical Behavior of p‐tert‐Butyl‐sulfonylcalix[4]arene and Its Selective Complexation with Metal Ions at Water‐Air Interface

The electrochemical behavior of p‐tert‐butyl‐sulfonylcalix[4]arene (SCA) has been investigated by cyclic voltammetry. The results show that there is an irreversible electrochemical oxidative wave when the potential ranges from 0.9 to 1.9 V versus saturated calomel electrode (SCE) in CH₂Cl₂ at a glassy carbon electrode. The kinetic parameters of the andic wave, such as α,n, k_s, D and the diffusion activation energy (E_d), were discussed. In addition, the interaction of SCA with metal ions at the water‐air interface was also discussed by Langmuir‐Blodgett (LB) techniques. The results confirm that the selectivity of SCA as ligand for Pb²⁺ in monomolecular film is very high by complexation action, which provide the foundation that LB film of SCA modified glassy carbon electrode (GCE) as voltammetric sensor to detect trace amounts of Pb²⁺.     

Voltammetric Determination of Phenoxybenzyl‐Type Insecticides at Chemically Modified Conducting Polymer‐Carbon Nanotubes Coated Electrodes

The electrochemical reduction of three common insecticides such as cypermethrin (CYP), deltamethrin (DEL) and fenvalerate (FEN) was investigated at glassy carbon electrode (GCE), multiwalled carbon nanotubes modified GCE (MWCNT‐GCE), polyaniline (herein called as modifier M₁) and polypyrrole (herein called as modifier M₂) deposited MWCNT/GCE using cyclic voltammetry. Influences of pH, scan rate, and concentration were studied. The surface morphology of the modified film was characterized by scanning electron microscopy (SEM) and X‐ray diffraction analysis (XRD). A systematic study of the experimental parameters that affect differential pulse stripping voltammetry (DPSV) was carried out and the optimized experimental conditions were arrived at. The calibration plots were linear over the insecticide's concentration range 0.1–100 mg L^?1 and 0.05–100 mg L^?1 for all the three insecticides at MWCNT‐GCE and MWCNT(M₁)‐GCE respectively. The MWCNT(M₂)‐GCE performed well among the three electrode systems and the determination range obtained was 0.01–100 mg L^?1 for CYP, DEL and FEN. The limit of detection (LOD) was 0.35 μg L^?1, 0.9 μg L^?1 and 0.1 μg L^?1 for CYP, DEL and FEN respectively on MWCNT(M₂)‐GCE modified system. Suitability of this method for the trace determination of insecticide in spiked soil sample was also determined.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.     

Sensitive amperometric pyridoxine sensor based on self‐assembled Prussian blue nanoparticle‐modified poly(o‐phenylenediamine)/glassy carbon electrode

Prussian blue nanoparticles (PBNPs) were prepared by a self‐assembly process on a glassy carbon electrode (GCE) modified with poly(o‐phenylenediamine) (PoPD) film. The stepwise fabrication process of PBNP‐modified PoPD/GCE was characterized using scanning electron microscopy and electrochemical impedance spectroscopy. The prepared PBNPs showed an average size of 70 nm and a homogeneous distribution on the surface of the modified electrode. The PBNPs/PoPD/GCE showed electrocatalytic activity towards the oxidation of pyridoxine (PN) and was used as an amperometric sensor. The modified electrode exhibited a linear response for PN oxidation over the concentration range 3–38.5 μM with a detection limit of ca 6.10 × 10^?7 M (S/N = 3) and sensitivity of 2.79936 × 10³ mA M^?1 cm^?2 using an amperometric method. The mechanism and kinetics of the catalytic oxidation reaction of PN were investigated using cyclic voltammetry and chronoamperometry. The values of α, k_cat and D were estimated as 0.36, 1.089 × 10² M^?1 s^?1 and 8.9 × 10^?5 cm² s^?1, respectively. This sensor also exhibited good anti‐interference and selectivity. Copyright © 2016 John Wiley & Sons, Ltd.     

Graphene Nanosheets Modified Glassy Carbon Electrode as a Highly Sensitive and Selective Voltammetric Sensor for Rutin

Graphene nanosheets modified glassy carbon electrode (GNs/GCE) was fabricated as voltammetric sensor for rutin with good sensitivity, selectivity and reproducibility. The sensor exhibits an adsorption‐controlled, reversible two‐proton and two electron transfer reaction for the oxidation of rutin with a peak‐to‐peak separation (ΔE_p) of 26 mV as revealed by cyclic voltammetry. Moreover, the redox peak current increased about 14 times than that on bare glassy carbon electrode (GCE). The linear response of the sensor is from 1×10^?7 to 1×10^?5 M with a detection limit of 2.1 × 10^?8 M (S/N = 3). The method was successfully applied to determine rutin in tablets with satisfied recovery.     

Langmuir–Blodgett film of tetraoxocalix[2]arene[2]triazine modified electrode for voltammetric determination of copper ion

In the present work, a new voltammetric sensor, Langmuir–Blodgett (LB) film of tetraoxocalix[2]arene[2]triazine (TOCT) modified glassy carbon electrode (LB_TOCT-GCE), for trace analysis of copper ion in water samples, was prepared. The morphology of LB_TOCT-GCE was characterized by cyclic voltammetric method, electrochemical impedance spectroscopy, and atomic force microscope. The recognizing mechanism of LB_TOCT-GCE for copper ion in aqueous solution was discussed. Under the optimum experimental conditions, using square wave stripping voltammetry and accumulation time of 300 s, the peak currents were linear relationship with Cu²⁺ concentrations in the range of 2 × 10⁻⁹ to 1 × 10⁻⁶ mol L⁻¹, with detection limit of 1 × 10⁻¹⁰ mol L⁻¹. By this method, real samples (lake water, drinking water, and city wastewater) were analyzed with satisfactory results. In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility, and stability.     

A Graphene Oxide‐DNA Electrochemical Sensor Based on Glassy Carbon Electrode for Sensitive Determination of Methotrexate

Methotrexate (MTX) was used as an anti‐cancer drug, but its excessive use can cause serious side effects, it was necessary to monitor MTX in vivo. In this report, DNA was immobilized on a glassy carbon electrode (GCE) modified with graphene oxide (GO) to develop an electrochemical sensor for sensitive determination of MTX for the first time. The adsorptive voltammetric behaviors of MTX on DNA sensor were investigated using differential pulse voltammetry (DPV). The peak current response of guanine in DNA was used as a determination signal of MTX in acetate buffer solution pH 4.6. Voltammetric investigations revealed that the proposed method could determine MTX in the concentration range from 5.5×10⁻⁸ to 2.2×10⁻⁶ mol L⁻¹ with a lower detection limit of 7.6×10⁻9 mol L⁻¹ (S/N=3). The method was applied to detect MTX in human blood serum and diluted urine samples with excellent recoveries of 97.4–102.5 %. Compared with the previous studies, the DNA/GO/GCE electrode constructed by us based on the change rate of guanine current (R%) in DNA, proportionally reflecting the MTX concentration, is simple and sensitive .     

Development of a Molecularly Imprinted Poly(Acrylic Acid)‐MWCNT Nanocomposite Electrochemical Sensor for Tramadol Determination in Pharmaceutical Samples

A new voltammetric sensor based on molecularly imprinted poly(acrylic acid)‐MWCNT nanocomposite (MIP‐MWCNT) drop‐coated onto glassy carbon electrode (GCE) was developed and applied to tramadol (TR) determination in pharmaceutical samples. The voltammetric sensor prepared by suspension of MIP‐MWCNT at 1 : 1 (w/w) ratio show an improved performance compared to unmodified GCE. The electrochemical method is based on preconcentration of tramadol onto MIP‐MWCNT modified GCE surface at ?1.5 V vs Ag/AgCl for 180 s in 0.1 Britton‐Robinson buffer (pH 8.0) at stirred solution. Upon preconcentration, the differential anodic voltammogram was recorded under the optimized condition giving rise to an analytical curve varying from 9.0 up to 30.0 μmol L^?1 (R²=0.997) and limits of detection and quantification of 1.4 and 4.8 μmol L^?1, respectively. The method precision was assessed in terms of intraday (n=6) and interday (two consecutive days) precision, giving relative standard deviations (RSD%) values between 2.8 to 7.4 %. Excipients usually found in pharmaceutical pills (magnesium stearate, microcrystalline cellulose, starch, and silica) and paracetamol were evaluated as potential interferents, however no interference was evidenced in TR determination. The method applicability was evaluated by TR analysis in pharmaceutical samples. Moreover, the method accuracy was attested by comparison of addition and recovery assays with a reference technique (high‐performance liquid chromatography).     

Electrochemical Determination of Vitamin B12 Based on Cu2+‐Involved Fenton‐like Reaction

Poly(thionine) (PTH) film was generated on the electrochemically activated glassy carbon electrode (GCE(ea)) by using the two‐step cyclic voltammetric scan. Scanning electron microscopy, infrared spectral analysis and electrochemical measurement were employed to characterize the modified electrode surface. Hydroxyl radicals, which were produced by the Fenton‐like reaction, could induce the effective oxidization of PTH under near‐neutral condition and cause the notable enhancement of the cathodic peak current (I_pc) during the potential cycling process. Due to the binding of copper ions with the ligands liberated from V_B12 and the inferior catalytic ability of Co²⁺ for the generation of hydroxyl radicals, the addition of V_B12 into the Cu²⁺?H₂O₂ system inhibited the oxidization of PTH and resulted in the decrease of the I_pc value. The cathodic peak current change was linear with the logarithm of the V_B12 concentration in the range of 10 nmol L^?1–100 μmol L^?1 with a detection limit of 2 nmol L^?1 under optimal conditions. The developed sensor displayed excellent analytical performance including high sensitivity, good selectivity, acceptable reproducibility and satisfactory stability. The V_B12 content in the injection sample was measured and the recovery values were in the range of 92.0 %–102 %.     

Over‐Oxidized Poly (Phenol Red) Film Modified Glassy Carbon Electrode for Anodic Stripping Voltammetric Determination of Ultra‐Trace Antimony (III)

In this study, we introduce a very sensitive and selective method for the differential pulse anodic stripping determination of Sb(III) ion on the over‐oxidized poly(phenol red) modified glassy carbon electrode (PPhRed_ox/GCE) in 0.1 mol L^‐1 HCl medium. The formation of both poly(phenol red) and over‐oxidized poly(phenol red) film on the electrode surfaces were characterized by electrochemical impedance spectroscopy, X‐ray photoelectron spectroscopy and scanning electron microscopy techniques. An anodic stripping peak of Sb(III) was observed at 0.015 V on the PPhRed_ox/GCE. Higher anodic stripping peak current of Sb(III) was obtained at PPhRed_ox/GCE compared with both bare GCE and poly(phenol red) film modified GCE (PPhRed/GCE). The calibration graph consisted of two linear segments of 0.044 ‐ 1.218 μg L⁻¹ and 3.40 – 18.26 μg L⁻¹ with a detection limit of 0.0075 μg L⁻¹. The proposed over‐oxidized polymer film modified electrode was applied successfully for the analysis of antimony in different spiked water samples. Spiked recoveries for water samples were obtained in the range of 93.0–103.0%. The accuracy of the method was also verified through the analysis of standard reference materials (SCP SCIENCE‐EnviroMAT™ EP−L‐2).     

Determination of Copper at a Glassy Carbon Electrode Modified with Langmuir–Blodgett Film of p‐tert‐Butylthiacalix[4]arene

A new type of voltammetric sensor, Langmuir–Blodgett film of p‐tert‐butylthiacalix[4]arene modified glassy carbon electrode, was advanced and used for determining copper at trace levels by differential pulse stripping voltammetry. Calibration plot was found to be linear in the range of 2×10^?8 M to 5×10^?6 M; the detection limit was 2×10^?9 M. Possible recognition mechanism was also discussed. From determination of Copper in real samples (river, lake and tap water) it can be concluded that the method is rapid, sensitive in determining of copper and can be used in the analysis of natural water samples.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Simultaneous Determination of Nitrophenol Isomers Based on β‐Cyclodextrin Functionalized Reduced Graphene Oxide

β‐CD modified reduced graphene oxide (RGO) sheets have been prepared and characterized by TEM, AFM, IR, EIS and CVs. In comparison with bare glass carbon electrode (GCE) and RGO modified GCE, CD‐RGO/GCE showed much higher peak currents to the reduction of nitrophenol isomers (NPs), attributed to the larger specific surface area of RGO and high quantities of host–guest recognition sites. Three pairs of redox peaks are observed on the CVs of CD‐RGO for p‐NP (0.3 V), o‐NP (?0.2 V) and m‐NP (0.05 V), separating well with each other. Under the optimized condition, the anodic peak currents were linear over ranges around 1–10 mg dm^?3 for p‐NP, 1–9 mg dm^?3 for o‐NP and 1–6 mg dm^?3 for m‐NP, with the detection limits of 0.05 mg dm^?3, 0.02 mg dm^?3 and 0.1 mg dm^?3, respectively. Thus, the CD‐RGO is expected to be a promising sensor material for detecting trace NPs in waste water.     

Adsorptive Stripping Differential Pulse Voltammetric Determination of Risperidone with a Multi‐Walled Carbon Nanotube‐Ionic Liquid Paste Modified Glassy Carbon Electrode

A new composite electrode has been fabricated based on coating multi‐walled carbon nanotubes (MWCNTs) and n‐octylpyridinum hexafluorophosphate (OPPF₆) ionic liquid composite on a glassy carbon (GC) electrode (OPPF₆‐MWCNTs/GCE). This electrode shows very attractive electrochemical performances for electrooxidation of risperidone (RIS) compared to conventional electrodes using carbon and mineral oil, notably improved sensitivity and stability. The oxidation peak potentials in cyclic voltammogram of RIS on the OPPF₆‐MWCNTs/GCE was occurred around 230 mV vs. SCE at Britton–Robinson (B–R) buffer (pH 4.0) at scan rate of 100 mV s^?1. The electrochemical parameters such as diffusion coefficient (D), charge transfer coefficient (α) and the electron transfer rate constant (k/_s) were determined using cyclic voltammetry. Under the optimized conditions, the peak current was linear to risperidone concentration over the concentration range of 10–200 nM with sensitivity of 0.016 μA/nM^?1 using differential pulse voltammetry. The detection limit was 6.54 nM (S/N = 3). The electrode also displayed good selectivity and repeatability. In the presence of clozapine (CLZ) the response of RIS kept almost unchanged. Thus this electrode could find application in the determination of RIS in some real samples. The analytical performance of the OPPF₆‐MWCNTs/GCE was demonstrated for the determination of RIS in human serum and pharmaceutical samples.     

The electrode modified with Langmuir–Blodgett film of p-tert-butylcalix[4]arene derivatives with sulfur-containing functionalities for the determination of silver

A new voltammetric sensor, based on a new p-tert-butylcalix[4]arene derivative (TCAD) modified glassy carbon electrode (GCE) using Langmuir–Blodgett (LB) technique, was designed successfully and used for recognition and determination of Ag⁺. The π?-?A isotherms suggested that the monolayer of TCAD can coordinate with Ag⁺ at the air–water surface. Under the optimum experimental conditions, this voltammetric sensor shows a linear voltammetric response for Ag⁺ in the range of 1.0?×?10^?8?～?6.0?×?10^?6?mol?L^?1 with detection limit 5.0?×?10^?9?mol?L^?1. The high sensitivity, selectivity, and stability of this LB film modified electrode also demonstrate its practical application for a simple, rapid and economical determination of Ag⁺ in water sample.     

A Nitrite Biosensor Based on Coimmobilization of Nitrite Reductase and Viologen‐Modified Polysiloxane on Glassy Carbon Electrode

Copper containing nitrite reductase (Cu‐NiR) and viologen‐modified sulfonated polyaminopropylsiloxane (PAPS‐SO₃H‐V) were co‐immobilized on glassy carbon electrode (GCE) by hydrophilic polyurethane (HPU) drop‐coating, and the electrode was tested as a reagentless electrochemical biosensor for nitrite detection. The newly synthesized PAPS‐SO₃H‐V as an electron transfer (ET) mediator between electrode and NiR was effective, and could be effectively immobilized in HPU membrane. The NiR and PAPS‐SO₃H‐V co‐immobilized GCE used as a nitrite biosensor showed the following performance factors: sensitivity=12.0 nA μM^?1, limit of detection (LOD)=60 nM (S/N=3), linear response range=0–18 μM (r²=0.996) and response time (t_90%)=60 s, respectively. Lineweaver–Burk plot shows that apparent Michaelis–Menten constant (K is 101 μM. Storage stability of the sensor is 51 days (80% of initial activity) in condition of storing in ambient air at room temperature. The sensor showed a relative standard deviation (RSD) of 3.2% (n=5) even in condition of injection of 1 μM nitrite. Interference study showed that common anions in water sample such as chlorate, chloride, sulfate and sulfite do not interfere with the nitrite detection. However, nitrate interfered with a relative sensitivity of 80% due to inherent character of the enzyme used.     

Sensitive Voltammetric Response of p‐Nitroaniline on Single‐Wall Carbon Nanotube‐Ionic Liquid Gel Modified Glassy Carbon Electrodes

An ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆)‐single‐walled carbon nanotube (SWNT) gel modified glassy carbon electrode (BMIMPF₆‐SWNT/GCE) is fabricated. At it the voltammetric behavior and determination of p‐nitroaniline (PNA) is explored. PNA can exhibit a sensitive cathodic peak at ?0.70 V (vs. SCE) in pH 7.0 phosphate buffer solution on the electrode, resulting from the irreversible reduction of PNA. Under the optimized conditions, the peak current is linear to PNA concentration over the range of 1.0×10^?8–7.0×10^?6 M, and the detection limit is 8.0×10^?9 M. The electrode can be regenerated by successive potential scan in a blank solution for about 5 times and exhibits good reproducibility. Meanwhile, the feasibility to determine other nitroaromatic compounds (NACs) with the modified electrode is also tested. It is found that the NACs studied (i.e., p‐nitroaniline, p‐nitrophenol, o‐nitrophenol, m‐nitrophenol, p‐nitrobenzoic acid, and nitrobenzene) can all cause sensitive cathodic peaks under the conditions, but their peak potentials and peak currents are different to some extent. Their peak currents and concentrations show linear relationships in concentration ranges with about 3 orders of magnitude. The detection limits are 8.0×10^?9 M for p‐nitroaniline, 2.0×10^?9 M for p‐nitrophenol, 5.0×10^?9 M for o‐nitrophenol, 5.0×10^?9 M for m‐nitrophenol, 2.0×10^?8 M for p‐nitrobenzoic acid and 8.0×10^?9 M for nitrobenzene respectively. The BMIMPF₆‐SWNT/GCE is applied to the determination of NACs in lake water.     

Enhanced Oxidation of Simvastatin at a Multi‐Walled Carbon Nanotubes‐Dihexadecyl Hydrogen Phosphate Composite Modified Glassy Carbon Electrode and the Application in Determining Simvastatin in Pharmaceutical Dosage Forms

A sensitive electrochemical method for the determination of simvastatin (SV) was established, based on the enhanced oxidation of SV at a multi‐walled carbon nanotubes‐dihexadecyl hydrogen phosphate composite modified glassy carbon electrode (MWNTs‐DHP/GCE). The voltammetric studies showed that MWNTs instead of DHP or GCE could effectively catalyze the oxidation of SV. The dependence of oxidation current on SV concentration was explored under optimal conditions, which exhibited a good linear relationship in the range of 1.0×10^?7–7.5×10^?6 M. The detection limit of SV was also examined and a low value of 5.0×10^?8 M was obtained for 5 min accumulation (σ=3). This electrode was applied to the detection of SV in drug forms and the results were in accordance with those obtained by UV spectroscopy.     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.