Cobalt(II) Schiff Base/Large Mesoporous Carbon Composite Film Modified Electrode as Electrochemical Biosensor for Hydrogen Peroxide and Glucose

A simple method was developed to prepare a cobalt(II) Schiff base (Co(salen))/large mesoporous carbon (LMC) composite film. The structure and electrocatalytic performance of the Co(salen)/LMC film were investigated by scanning electron microscopy (SEM) and cyclic voltammetry (CV). The Co(salen)/LMC film exhibits high electrocatalytic activity toward H₂O₂, such as low detection limit (8.5×10^?7 M) and wide linear concentration range (2.0×10^?6–8.9×10^?3 M). Furthermore, glucose oxidase (GOD) was self‐assembled on the surface of the Co(salen)/LMC film modified electrode. Determination of glucose in human blood serum with satisfying result was investigated by the resulting biosensor.     

铂纳米颗粒修饰直立碳纳米管电极的葡萄糖生物传感器

基于Pt纳米颗粒修饰直立的碳纳米管电极制备了葡萄糖生物传感器.铂纳米颗粒是利用电位脉冲沉积法修饰到直立碳纳米管上的,可以增强电极对酶反应过程当中产生的过氧化氢的催化行为.用扫描电镜和透射电镜观察了直立碳纳米管在修饰Pt纳米颗粒前后的形态.该酶电极对葡萄糖的氧化表现出很好的响应,线性范围为1×10-5～7×10-3mol/L,响应时间小于5s,并且有很好的重现性.     

Amperometric Glucose Biosensor Based on Glucose Oxidase Encapsulated in Carbon Nanotube–Titania–Nafion Composite Film on Platinized Glassy Carbon Electrode

A highly sensitive and selective glucose biosensor has been developed based on immobilization of glucose oxidase within mesoporous carbon nanotube–titania–Nafion composite film coated on a platinized glassy carbon electrode. Synergistic electrocatalytic activity of carbon nanotubes and electrodeposited platinum nanoparticles on electrode surface resulted in an efficient reduction of hydrogen peroxide, allowing the sensitive and selective quantitation of glucose by the direct reduction of enzymatically‐liberated hydrogen peroxide at ?0.1 V versus Ag/AgCl (3 M NaCl) without a mediator. The present biosensor responded linearly to glucose in the wide concentration range from 5.0×10^?5 to 5.0×10^?3 M with a good sensitivity of 154 mA M^?1cm^?2. Due to the mesoporous nature of CNT–titania–Nafion composite film, the present biosensor exhibited very fast response time within 2 s. In addition, the present biosensor did not show any interference from large excess of ascorbic acid and uric acid.     

Amperometric Biosensors Based on Platinum Nanowires

Abstract

Platinum nanowires (PtNW) were prepared by an electrodeposition strategy using nanopore alumina template. The nanowires prepared were dispersed in chitosan (CHIT) solution and stably immobilized onto the surface of glassy carbon electrode (GCE). The electrochemical behavior of PtNW‐modified electrode and its application to the electrocatalytic reduction of hydrogen peroxide (H₂O₂) are investigated. The modified electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. As an application example, the glucose oxidase was immobilized onto the surface of PtNW‐modified electrode through cross‐linking by glutaric dialdehyde. The detection of glucose was performed in phosphate buffer at –0.2 V. The resulting glucose biosensor exhibited a short response time (<8 s), with a linear range of 10^?5?10^?2 M and detection limit of 5×10^?6 M.     

A Nitric Oxide Biosensor Based on Myoglobin Adsorbed on Multi‐Walled Carbon Nanotubes

Myoglobin (Myb) of horse heart is incorporated on multi‐walled carbon nanotubes (MWNTs) and immobilized at a glassy carbon (GC) electrode surface. Its electrochemical behavior and enzyme activity are characterized by employing electrochemical methods. The results indicate that MWNTs can obviously promote the direct electron transfer between Myb and electrode, and that the Myb on MWNTs behaves as an enzyme‐like activity towards the electrochemical reduction of nitric oxide (NO). Accordingly, an unmediated NO biosensor is constructed. Experimental results reveal that the peak current related to NO is linearly proportional to its concentration in the range of 2.0×10^?7–4.0×10^?5 mol/L. The detection limit is estimated to be 8.0×10^?8 mol/L. Considering a relative standard deviation of 2.1% in seven independent determinations of 1.0×10^?5 mol/L NO, this biosensor shows a good reproducibility. The biosensor based on Myb/MWNTs modified electrode can be used for the rapid determination of trace NO in aqueous solution with a good stability, nice selectivity and easy construction.     

An H2O2 Biosensor Based on Immobilization of Horseradish Peroxidase Labeled Nano‐Au in Silica Sol‐Gel/Alginate Composite Film

Abstract

A novel approach to assemble an H₂O₂ amperometric biosensor was introduced. The biosensor was constructed by entrapping horseradish peroxidase (HRP) labeled nano‐scaled particulate gold (nano‐Au) (HRP‐nano‐Au electrostatic composite) in a new silica sol‐gel/alginate hybrid film using glassy carbon electrode as based electrode. This suggested strategy fully merged the merits of sol‐gel derived inorganic‐organic composite film and the nano‐Au intermediator. The silica sol‐gel/alginate hybrid material can improve the properties of conventional sol‐gel material and effectively prevent cracking of film. The entrapment of HRP in the form of HRP‐nano‐Au can not only factually prevent the leaking of enzyme out of the film but also provide a favorable microenvironment for HRP. With hydroquinone as an electron mediator, the proposed HRP electrode exhibited good catalytic activity for the reduction of H₂O₂. The parameters affecting both the qualities of sol‐gel/alginate hybrid film and the biosensor response were optimized. The biosensor exhibited high sensitivity of 0.40 Al mol^?1 cm^?2 for H₂O₂ over a wide linear range of concentration from 1.22×10^?5 to 1.46×10^?3 mol L^?1, rapid response of <5 s and a detection limit of 0.61×10^?6 mol L^?1. The enzyme electrode has remarkable stability and retained 86% of its initial activity after 45 days of storage in 0.1 mol L^?1 Tris‐HCl buffer solutions at pH 7.     

Pt nanoparticles modified Au nanowire array for amperometric and potentiometric detection of glucose

A new glucose biosensor, based on the modification of highly ordered Au nanowire arrays (ANs) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. Morphologies of ANs and ANs/PtNPs were observed by scanning electron microscope. The electrochemical properties of ANs, ANs/GOx, ANs/PtNPs, and ANs/PtNPs/GOx electrodes were compared by cyclic voltammetry. Results obtained from comparison of the cyclic voltammograms show that PtNPs modification enhances electrochemical catalytic activity of ANs to H₂O₂. Hence, ANs/PtNPs/GOx biosensor exhibits much better sensing to glucose than ANs/GOx. Optimum deposition time of ANs/PtNPs/GOx biosensor for both amperometric and potentiometric detection of glucose was achieved to be 150 s at deposition current of 1?×?10^?6 A. A sensitivity of 0.365 μA/mM with a linear range from 0.1 to 7 mM was achieved for amperometric detection; while for potentiometric detection the sensitivity is 33.4 mV/decade with a linear range from 0.1 to 7 mM.     

一种基于壳聚糖固定葡萄糖氧化酶的葡萄糖生物传感器的研究

本文选用生物相容性好的壳聚糖作为基体材料，使其与戊二醛交联成网状结构包埋葡萄糖氧化酶制成电化学传感器。这种壳聚糖膜不仅可以减小葡萄糖氧化酶的流失，而且能为酶提供了适宜的微环境。用红外光谱、紫外光谱及透射电镜对膜的形态和性质进行了表征。实验结果表明该传感器具有很快的响应速度，很好的稳定性和重现性，能选择性地催化葡萄糖并测定其浓度。该传感器的制备方法简单，成本低，于冰箱中放置两周信号保持在90％以上，对葡萄糖测量的线性范围为1×10^-5 - 3.4×10^-3mol•L^-1，当信噪比为3:1时检测限为5×10^-6mol•L^-1。     

Pure copper vs. mixed copper and palladium hexacyanoferrates for glucose biosensing applications

A glucose amperometric biosensor was developed. Glucose oxidase enzyme was immobilized by means of a Nafion membrane on glassy carbon modified with an electrochemically deposited mixed Cu and Pd hexacyanoferrate (CuPdHCF). According to the data provided by X-ray atomic spectroscopy measurements, this Cu- and Pd-based hexacyanoferrate is likely to be a mixture of single CuHCF and PdHCF pure phases. The biosensor performances were evaluated by recording the steady-state currents due to submillimolar additions of glucose to a potassium buffer solution (pH 5.5) and exploiting the electrocatalytic reduction of the enzymatically produced hydrogen peroxide. The CuPdHCF-based biosensor exhibited a sensitivity of 8.1?±?0.6 A M^?1 m^?2, a limit of detection of 1.4?×?10^?5 M, and a linear response range extending between 5?×?10^?5 and 4?×?10^?4 M, with a dynamic response range up to 4?×?10^?3 M glucose. Electrode sensitivity and signal stability resulted more satisfactory as compared to those of a CuHCF-based biosensor fabricated according to the same procedure. The selectivity was investigated through an interference study. The response to easily oxidizable species was found to be low enough to allow glucose determination in biological samples.     

Immobilization and Bioelectrochemistry of Hemoglobin Based on Carrageenan and Room Temperature Ionic Liquid Composite Film

A novel biopolymer/room‐temperature ionic liquid composite film based on carrageenan, room temperature ionic liquid (IL) [1‐butyl‐3‐methylimidazolium tetra?uoroborate ([BMIM]BF₄)] was explored for immobilization of hemoglobin (Hb) and construction of biosensor. Direct electrochemistry and electrocatalytic behaviors of Hb entrapped in the IL‐carrageenan composite ?lm on the surface of glassy carbon electrode (GCE) were investigated. UV‐vis spectroscopy demonstrated that Hb in the IL‐carrageenan composite ?lm could retain its native secondary structure. A pair of well‐de?ned redox peaks of Hb was obtained at the Hb‐IL‐carrageenan composite ?lm modi?ed electrode through direct electron transfer between the protein and the underlying electrode. The heterogeneous electron transfer rate constant (k_s) was 2.02 s^?1, indicating great facilitation of the electron transfer between Hb and IL‐carrageenan composite film modi?ed electrode. The modi?ed electrode showed excellent electrocatalytic activity toward reduction of hydrogen peroxide with a linear range of 5.0×10^?6 to 1.5×10^?4 mol/L and the detection limit was 2.12×10^?7 mol/L (S/N=3). The apparent Michaelis‐Menten constant K_M^app for hydrogen peroxide was estimated to be 0.02 mmol/L, indicating that the biosensor possessed high af?nity to hydrogen peroxide. In addition, the proposed biosensor showed good reproducibility and stability.     

Preparation of Co3O4/graphene Oxide Composites by a Depositing‐decompostion Method and its Application for Electrochemical Determination of Glucose

Co₃O₄/graphene oxide (GO) nanocomposites were successfully prepared by a depositing‐decomposition method. The as‐prepared samples were characterized by scanning electron microscopy (SEM) and Raman spectroscopy. Cyclic voltammetry (CV) was used to evaluate the electrochemical response of a glass carbon electrode (GCE) modified with Co₃O₄/GO nanocomposite towards glucose. Compared with the Co₃O₄/GCE, the Co₃O₄/GO/GCE exihibits higher electrocatalytic activity due to the synergistic effects of electrocatalytic ability of Co₃O₄ and large surface of GO. The Co₃O₄/GO/GCE was applied for glucose detection in alkaline solution. The linear current response range of glucose on Co₃O₄/GO/GCE covered the range from 9 × 10^?5 to 6.03 × 10^?3 M, with a detection limit of 5.2 × 10^?7 M (S/N = 3).     

One‐Step Electrodeposited Carbon Nanotube/Zirconia/Myoglobin Film for Direct Electron Transfer and Electrocatalysis

A nanobiocomposite film consisted of zirconia, multiwalled carbon nanotubes (MWNTs) and Myoglobin (Mb) was electrochemically deposited on the electrode. Direct electron transfer for the immobilized Mb was realized and high electrocatalytic efficiency toward H₂O₂ was observed. The proposed biosensor via a simple one‐step electrodeposition method displayed a broader linear range and a lower detection limit for H₂O₂, as compared with those CNT or ZrO₂ based biosensor. The linear range is from 2 × 10^?6 M to 1 × 10^?3 M with the detection limit of 6 × 10^?7 M. The present strategy provides a simple and effective method to assemble CNT, ZrO₂ and enzyme nanohybrid on the electrode and expands the scope of CNT‐based electrochemical devices.     

二茂铁衍生物电子传递剂键合的溶胶-凝胶葡萄糖生物传感器

The sol-gel derived glucose biosensor was developed, and the sol-gel membrane was organically modified by N-（3-triethoxysilylpropyl）-ferrocenylmethylamine （FcSi） as sol-gel precursor to make electrochemical biosensor. The structure of biosensor was sol-gel/FcSi＋GOx/GC type （glucose oxidase, GOx）. The ferrocene mediator was chemically immobilized to the silane network, and GOx was entrapped to the sol-gel glass network. Therefore, these structures prevented mediator leakage and retained the enzyme activity. Additionally, pH of electrolyte, temperature effects, and interference of positive substances with biosensor were investigated. And the electrochemical performance of biosensor was studied by amperometry. The results indicated that the linear range, detection limit. and response slope of biosensor was 2.00×10^-4-1.57×10^-3 mol·L^-1, 2.0×10^-4 mol·L^-1 and 5.06×10^5 nA·mol^- 1·L, respectively.     

Amperometric Biosensor for Hydrogen Peroxide Based on Myoglobin Doped Multiwalled Carbon Nanotube Enhanced Grafted Collagen Matrix

Abstract

A reagentless H₂O₂ sensor based on the direct electron transfer of myoglobin (Mb) doped in multiwalled carbon nanotubes enhanced grafted collagen matrix is proposed. The formal potential of the immobilized Mb was ?0.358 V with a surface coverage of 4.0×10^?10 mol cm^?2. The electrode process was surface‐controlled with an electron transfer rate constant of 9.7 s^?1. The proposed biosensor displayed an excellent electrocatalytic response to the reduction of H₂O₂ with a linear range from 0.6 to 39.0 µM. Owing to the good biocompatibility and high enzyme loading of the matrix the biosensor exhibited acceptable stability and reproducibility.     

Analytical Biosensing of Hydrogen Peroxide on Brilliant Cresyl Blue/Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

A cationic quinine‐imide dye brilliant cresyl blue (BCB) and horseradish peroxidase (HRP) were co‐immobilized within ormosil on multiwalled carbon nanotubes modified glassy carbon electrode for the fabrication of highly sensitive and selective hydrogen peroxide biosensor. The presence of epoxy group in ormosil as organic moiety improves the mechanical strength and transparency of the film and amino group provides biocompatible microenvironment for the immobilization of enzyme. The presence of MWCNTs improved the conductivity of the nanocomposite film. The surface characterization of MWCNT modified ormosil nanocomposite film was performed with scanning electron microscopy (SEM) and atomic force microscopy (AFM). Cyclic voltammetry and amperometry measurements were used to study and optimize the performance of the resulting peroxide biosensor. The apparent Michaelis–Menten constant was determined to be 1.5 mM. The proposed H₂O₂ biosensor exhibited wide linear range from 3×10^?7 to 1×10^?4 M, and low detection limit 1×10^?7 M (S/N=3) with fast response time <5 s. The probable interferences in bio‐matrix were selected to test the selectivity and no significant response was observed in the biosensor. This biosensor possessed good analytical performance and long term storage stability.     

Multilayer Assembly of Hemoglobin and Colloidal Gold Nanoparticles on Multiwall Carbon Nanotubes/Chitosan Composite for Detecting Hydrogen Peroxide

Chitosan (CS) was chosen for dispersing multi‐wall carbon nanotubes (MWNTs) to form a stable CS‐MWNTs composite, which was first coated on the surface of a glassy carbon electrode to provide a containing amino groups interface for assembling colloidal gold nanoparticles (GNPs), followed by the adsorption of hemoglobin (Hb). Repeating the assembly step of GNPs and Hb resulted in {Hb/GNPs}_n multilayers. The assembly of GNPs onto CS‐MWNTs composites was confirmed by transmission electron microscopy. The consecutive growth of {Hb/GNPs}_n multilayers was confirmed by cyclic voltammetry and UV‐vis absorption spectroscopy. The resulting system brings a new platform for electrochemical devices by using the synergistic action of the electrocatalytic activity of GNPs and MWNTs. The resulting biosensor displays an excellent electrocatalytic activity and rapid response for hydrogen peroxide. The linear range for the determination of H₂O₂ was from 5.0×10^?7 to 2.0×10^?3 M with a detection limit of 2.1×10^?7 M at 3σ and a Michaelis–Menten constant K_M^app value of 0.19 mM.     

Amperometric Glucose Biosensor Based on the Deposition of Copper and Glucose Oxidase onto Glassy Carbon Transducer

ABSTRACT

The performance of a first generation glucose amperometric biosensor based on the entrapment of glucose oxidase (GOx) within a net of copper electrodeposited onto activated glassy carbon electrode, is described. The copper electrodeposited offers an efficient electrocatalytic activity towards the reduction of enzymatically-liberated hydrogen peroxide, allowing for a fast and sensitive glucose quantification. The influence of the electrodeposition conditions (pH, potential, time, copper salt and enzyme concentrations) on the response of the bioelectrode was evaluated from the amperometric signals of hydrogen peroxide and glucose. The combination of copper electrodeposition with a nation membrane allows an excellent selectivity towards easily oxidizable compounds such as uric and ascorbic acids at an operating potential of -0.050 V. The response is linear up to 2.0 × 10^?2 M glucose, the detection limit being 1.2 × 10^?3 M.     

Sensitive and Selective Sensing of Hydrogen Peroxide with Iron‐Tetrasulfophthalocyanine‐Graphene‐Nafion Modified Screen‐Printed Electrode

We developed a novel iron‐tetrasulfophthalocyanine‐graphene‐Nafion (FeTSPc‐GR‐Nafion) modified screen‐printed electrode to determine hydrogen peroxide (H₂O₂) with high sensitivity and selectivity. The nanocomposite film (FeTSPc‐GR‐Nafion) exhibits an excellent electrocatalytic activity towards oxidation of H₂O₂ at a potential of +0.35 V in the absence of enzyme. A comparative study reveals that the FeTSPc‐GR complexes play a dual amplification role. Amperometric experiment indicates that the sensors possess good sensitivity and selectivity, with a linear range from 2.0×10^?7 M to 5.0×10^?3 M and a detection limit of 8.0×10^?8 M. This sensor has been successfully used to develop the glucose biosensor and has also been applied to determine H₂O₂ in sterile water.     

Electrocatalytic Oxidation of Glucose at Carbon Nanotubes Supported PtRu Nanoparticles and Its Detection

PtRu nanoparticles were supported on multiwall carbon nanotubes (MWNTs), which were further fabricated as an electrode for nonenzymatic glucose sensing. Transmission electron microscope and X‐ray diffraction patterns were used for characterization of the PtRu nanoparticles on MWNTs. Cyclic voltammetry and chronopotentiometry were applied to investigate the performance of the PtRu/MWNTs nanocomposite electrode for nonenzymatic oxidation of glucose. The PtRu/MWNTs electrode shows high electrocatalytic activity towards the oxidation of glucose in 0.1 M NaOH solution and thus can be used to selectively detect glucose. Under the optimal potential (+0.55 V vs. Ag/AgCl), the biosensor effectively performs a selective electrochemical analysis of glucose in the presence of common interferents, such as ascorbic acid (AA), dopamine (DP) and uric acid (UA). Wide linear calibration ranging from 1 mM to 15 mM, high sensitivity of 28.26 μA cm^?2 mM^?1, low detection limit of 2.5×10^?5 M, and fast response time of 10 s were achieved for the detection of glucose at the PtRu/MWNTs electrode.     

Direct Electrochemistry and Electrocatalysis of the Hemoglobin Immobilized on Diazonium‐Functionalized Aligned Carbon Nanotubes Electrode

A simple and efficient electrochemical method is utilized to functionalize aligned carbon nanotubes (ACNTs) by the electrochemical reduction of 4‐carboxyphenyl diazonium salt. Thus hemoglobin (Hb) molecules were covalently immobilized on the diazonium‐ACNTs surface via carbodiimide chemistry. Direct electrochemistry and bioelectrocatalytic activity of the immobilized Hb were then investigated by cyclic voltammetry (CV) and amperometry techniques. It is showed that the Hb film on the diazonium‐ACNTs electrode had well‐defined redox peaks with a formal potential (E°) at ?312 mV (vs. Ag/AgCl), and the Hb‐ACNTs electrode displayed good electrocatalytic activity to H₂O₂ reduction. Owing to the high Hb covering on the ACNTs surface (Γ*=2.7×10^?9 mol cm^?2), the catalytic current were significantly improved when compared to the current measured at an Hb‐tangled carbon nanotubes electrode. The Hb‐ACNTs electrode exhibited high sensitivity, long‐term stability and wide concentration range from 40 μM to 3 mM for the amperometric detection of H₂O₂. The heterogeneous reaction rate constant (k_s) was 0.95±0.05 s^?1 and the apparent Michaelis–Menten constant (K was 0.15 mM.