Vortex-assisted surfactant-enhanced-emulsification liquid-liquid microextraction for the determination of triazine herbicides in water samples by microemulsion electrokinetic chromatography

A novel method based on the combination of microemulsion electrokinetic chromatography (MEEKC) and vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction (VSLLME) was developed for the determination of five triazine herbicides (simazine, atrazine, ametryn, prometryn, and terbutryn) in water samples. The five triazine herbicides were baseline separated by using the microemulsion buffer containing a 10 mmol/L borate buffer at pH 9.5, 2.5% (w/v) SDS as surfactant, 0.8% (w/v) ethyl acetate as oil phase, and 6.0% (w/v) 1‐butanol as cosurfactant. The optimum extraction conditions of VSLLME were as follows: 100 μL chloroform was used as extraction solvent, 5.0 × 10^?5 mol/L Tween‐20 was chosen as the surfactant to enhance the emulsification, and the extraction process was carried out by vortex mixing for 3 min. Under these optimum experimental conditions, the calibration curve was linear in the range of 2.0–200.0 ng/mL, with the correlation coefficients (r²) varying from 0.9927 to 0.9958. The detection limits of the method varied from 0.41 to 0.62 ng/mL. The purposed method was applied to the determination of five triazine herbicides in real water samples, and the recoveries were between 80.6 and 107.3%.     

Comparison of C18 silica and multi‐walled carbon nanotubes as the adsorbents for the solid‐phase extraction of Chlorpyrifos and Phosalone in water samples using HPLC

A comparison between C₁₈ silica and multi‐walled carbon nanotubes (MWCNTs) in the extraction of Chlorpyrifos and Phosalone in environmental water samples was carried out using HPLC. Parameters affecting the extraction were type and volume of elution solvent, pH and flow rate of sample through the adsorbent. The optimum conditions obtained by C₁₈ cartridge for adsorption of these pesticides were 4 mL dichloromethane as elution solvent, sample pH of 5, flow rate of 1 mL/min, and those for MWCNT cartridge were 3 mL dichloromethane, pH of 5 and flow rate of 10 mL/min, respectively. Optimized mobile phase for separation and determination of these compounds by HPLC was methanol/water (80:20 v/v) with pH=5 (adjusted with phosphate buffer). Under optimal chromatographic and SPE conditions, LOD, linear range and precision (RSD n=8) were 3.03×10^?3, 0.01–5.00 μg/mL and 2.7% for Chlorpyrifos and 4.03×10^?4, 0.01–5.00 μg/mL and 2.3% for Phosalone, in C₁₈ cartridge, respectively. These values for MWCNT were 4.02×10^?6, 0.001–0.500 μg/mL and 1.8% for Chlorpyrifos and 1.02×10^?6, 0.001–0.500 μg/mL and 1.5% for Phosalone, respectively.     

Enantioseparation of esbiothrin by cyclodextrin‐modified microemulsion and micellar electrokinetic chromatography

A comparison between chiral cyclodextrin‐modified microemulsion electrokinetic chromatography (CD‐MEEKC) and cyclodextrin‐modified micellar electrokinetic chromatography (CD‐MEKC) for the enantiomeric separation of esbiothrin was carried out. For both methods, the separation conditions were optimized by varying CD types and concentration, running buffer pH and compositions, organic modifiers, and temperature. The optimal CD‐MEEKC conditions were 0.8% n‐heptane, 2.3% SDS, 6.6% n‐butanol, 90.3% 10 mM sodium tetraborate containing 3% (w/v, the ratio of CD mass to microemulsion volume) methyl‐β‐cyclodextrin, pH 10, 25°C. The optimized CD‐MEKC conditions were 3.3% SDS, 96.7% 10 mM sodium tetraborate containing 5% (w/v) β‐CD, pH 10, 25°C. The difference in physicochemical properties of the buffer and CDs resulted in different optimal CD type. The competitive distribution between the microemulsion (or micelle) and chiral CD contributed to the chiral separation. Both methods provided excellent separation (R_s ～? 3) with similar migration time (ca. 15 min). CD‐MEEKC provided higher separation efficiencies (>300000) than CD‐MEKC (>200000). The LODs for CD‐MEEKC and CD‐MEKC were 4.7 μg/mL and 3.2 μg/mL, respectively. The RSDs of migration time and peak area for CD‐MEEKC were slightly higher than for CD‐MEKC. Both the demonstrated CD‐MEEKC and CD‐MEKC methods provided high efficiencies, low LODs, and reproducible enantioseparations of esbiothrin.     

A simple isocratic LC method for quantification of trace-level inorganic degradation impurities (ferricyanide,ferrocyanide, nitrite,and nitrate) in sodium nitroprusside injection and robustness by quality using design approach

This study developed and validated a trace-level quantification inorganic impurities method using reversed-phase HPLC and performed the robustness check using quality-by-design approach by varying the multiple factors simultaneously. This method is economical and simple and exhibits its stability-indicating nature [for the determination of ferrocyanide ([Fe(CN)₆]^4–), ferricyanide ([Fe(CN)₆]³⁻), nitrate (NO₃^–), and nitrite (NO₂^–)] in sodium nitroprusside (SNP) drug substance and liquid dosage form. Chromatographic separation was achieved using a USP L43 column (ACE PFP, 150 × 4.6 mm, 3 μm) with a simple isocratic elution. The buffer consists of potassium dihydrogen phosphate (50 mM), tetrabutylammonium hydrogen sulfate (9 mM), and tetrabutylammonium hydroxide (25 mM). The buffer pH was adjusted to 7.2 with tetrabutylammonium hydroxide. The mobile phase was mixed with the buffer and acetonitrile (68:32 v/v). The flow rate was 0.8 mL/min, column temperature was maintained at 30°C, and injection volume was 5.0 μL. The SNP impurities were monitored at 225 nm using a UV detector. Further, the method was validated per the International Council for Harmonisation (ICH) guidelines, and forced degradation studies were carried out under different stress conditions. The detector responses were plotted against concentrations, and correlation was linear (r > 0.999) over the range of 0.8–7.5 μg/mL for ferricyanide; 1.0–37.5 μg/mL for SNP; and 0.2–7.5 μg/mL for ferrocyanide, nitrite, and nitrate. The method repeatability was established for all the impurities with relative standard deviation (%), and the results were found to be less than 2.0.     

Development of an ultrasensitive stacking technique for 5‐nitroimidazole determination in untreated biological fluids by micellar electrokinetic chromatography

Cation‐selective exhaustive injection and sweeping followed by a MEKC separation is evaluated for the sensitive analysis of 5‐nitroimidazoles in untreated human serum and urine. Deproteinized serum and urine samples were diluted 76 and 143 times, respectively, in a low‐conductivity solvent (5.00 mM orthophosphoric acid containing 5.0% v/v methanol). Samples were electrokinetically injected at 9.8 kV for 632 s in a previously conditioned fused‐silica capillary (65.0 cm × 50 μm id). Separation was performed at –30 kV and 20°C using 44 mM phosphate buffer (pH 2.5), 123 mM SDS, and 8% v/v tetrahydrofurane as BGE. Signals were monitored at 276 nm and peak area was selected as analytical response. Good linearity (R² ≥ 0.988) and LODs lower than 1.5 and 1.8 μg/mL were achieved in serum and urine, respectively.     

Optimization of dispersive liquid–liquid microextraction with central composite design for preconcentration of chlordiazepoxide drug and its determination by HPLC‐UV

A simple, rapid, and sensitive method based on dispersive liquid–liquid microextraction combined with HPLC‐UV detection applied for the quantification of chlordiazepoxide in some real samples. The effect of different extraction conditions on the extraction efficiency of the chlordiazepoxide drug was investigated and optimized using central composite design as a conventional efficient tool. Optimum extraction condition values of variables were set as 210 μL chloroform, 1.8 mL methanol, 1.0 min extraction time, 5.0 min centrifugation at 5000 rpm min^?1, neutral pH, 7.0% w/v NaCl. The separation was reached in less than 8.0 min using a C₁₈ column using isocratic binary mobile phase (acetonitrile/water (60:40, v/v)) with flow rate of 1.0 mL min^?1. The linear response (r² > 0.998) was achieved in the range of 0.005–10 μg mL^?1 with detection limit 0.0005 μg mL^?1. The applicability of this method for simultaneous extraction and determination of chlordiazepoxide in four different matrices (water, urine, plasma, and chlordiazepoxide tablet) were investigated using standard addition method. Average recoveries at two spiking levels were over the range of 91.3–102.5% with RSD < 5.0% (n = 3). The obtained results show that dispersive liquid–liquid microextraction combined with HPLC‐UV is a fast and simple method for the determination of chlordiazepoxide in real samples.     

Sodium desoxycholate‐assisted capillary electrochromatography with methacrylate ester‐based monolithic column on fast separation and determination of coumarin analogs in Angelica dahurica extract

A rapid and sensitive CEC method with methacrylate ester‐based monolithic column has been developed for separation and determination of five coumarins (byakangelicin, oxypeucedanin hydrate, xanthotoxol, 5‐hydroxy‐8‐methoxypsoralen and bergapten) in Angelica dahurica extract. Surfactant sodium desoxycholate (SDC) was introduced into the mobile phase as the pseudostationary to dynamically increase the selectivity of analytes instead of increasing the hydrophobicity of stationary phase. In addition, other factors, pH of phosphate buffer, ACN content and applied voltage, for instance, have also an obvious effect on the resolution but little on the retention time. Satisfactory separation of these five coumarins was achieved within 6 min under a 30:70 v/v ACN–buffer containing 20 mM sodium dihydrogen phosphate (NaH₂PO₄) and 0.25 mM SDC at pH 2.51. The RSDs of intraday and interday for relative peak areas were less than 3.0% and 4.7%, respectively; and the recoveries were between 87.5% and 95.0%. The LODs were lower than 0.15 μg/mL and the LOQs were lower than 0.30 μg/mL, respectively, while calibration curves showed a good linearity (r² > 0.9979). Finally, five target coumarins from the crude extracts of A. dahurica were separated, purified, and concentrated by D‐101 macroporous resin, and were successfully separated and quantitatively determined within 6 min.     

Determination of aromatic amines in environmental water sample by hollow fiber-liquid phase microextraction and microemulsion electrokinetic chromatography

A novel method of microemulsion electrokinetic chromatography (MEEKC) coupled with hollow fiber-liquid phase microextraction (HF-LPME) was developed for determination of six aromatic amines including 4-methylaniline, 3-nitroaniline, 2,4-dimethylaniline, 4-chloroaniline, 3,4-dichloraniline and 4-aminobiphenyl. Baseline separation of six aromatic amines was achieved within 8 min by using the microemulsion buffer containing a 10 mM borate buffer at pH 9.0, 0.8% (v/v) ethyl acetate as oil droplets, 60 mM sodium cholate as surfactant, 5.0% (v/v) 1-butanol as co-surfactant. The influence factors relevant to the HF-LPME process were systemically investigated. The obtained enrichment factors were ranged between 70 and 157 in a 30 min extraction time, and the limits of detection ranged between 0.0021 and 0.0048 μg/mL. This purposed method was successfully applied for the analysis of aromatic amines in water sample and the recoveries were ranged from 87.2% to 99.8%.     

Capillary electrophoresis coupled with electrochemiluminescence detection for the separation and determination of thyreostatic drugs in animal feed

A rapid, simple, and practical method for the determination of four of the most used thyreostatic drugs (methimazole, 2‐thiouracil, 6‐methyl‐2‐thiouracil, and 6‐propyl‐2‐thiouracil) using CE coupled to electrochemiluminescence detection has been established, based on the electrochemiluminescence enhancement of tris(2,2‐bipyridyl)ruthenium(II) with these analytes. Parameters that affect separation and detection were optimized. Under the optimum experimental conditions, the four analytes could be well separated within 11 min at the separation voltage of 16 kV in a running solution containing 20 mM phosphate buffer (pH 9.0) and 1.0 × 10^?4 M Ru(bpy)₃²⁺, with a solution of 20 mM phosphate buffer (pH 12.0) containing 1.0 × 10^?4 M Ru(bpy)₃²⁺ in the electrochemiluminescence detection cell. The detection limits for methimazole, 6‐methyl‐2‐thiouracil, 6‐propyl‐2‐thiouracil, and 2‐thiouracil were 0.1, 0.05, 0.05, and 0.01 μM, respectively. The proposed method was applied to analyze these drugs in spiked animal feed samples. The recoveries were 88.2～99.0 and 86.4～98.7% for the intraday and interday analyses, respectively. The RSDs were 2.7～4.8 and 1.8～5.0% for the intraday and interday analyses, respectively. The results demonstrate that the proposed method has promising applications in the detection of thyreostatic drugs in animal feeds.     

Rapid separation of pharmaceutical enantiomers using electrokinetic chromatography with a novel chiral microemulsion

A novel oil-in-water microemulsion incorporating the chiral surfactant dodecoxycarbonylvaline (DDCV) was used to achieve the rapid enantiomeric separation of pharmaceutical drugs by electrokinetic chromatography (EKC). Incorporation of DDCV into a microemulsion resulted in an elution range more than double that provided the micellar form of the surfactant aggregate. Interestingly, for the same compounds the enantioselectivity provided by the chiral DDCV microemulsions ranged from 1.06-1.30 for the neutral and cationic drugs, which was slightly higher than that provided by chiral DDCV micelles. The use of a low surface tension oil (ethyl acetate) permitted a much lower concentration of chiral surfactant to be employed; this, together with the use of a zwitterionic buffer (ACES) resulted in a very low conductivity microemulsion that allowed a higher separation voltage to be utilized, resulting in rapid enantiomeric separations (< 8 min.). Mobility matching of the buffer cation(s) was used to improve peak shape and efficiencies. In our limited survey of the phase diagram, the optimum composition of the microemulsion buffer was 1.0% (w/v) DDCV (30 mM), 0.5% (v/v) ethyl acetate, 1.2% (v/v) 1-butanol and 50 mM ACES buffer at pH 7.     

Separation of catechins and methylxanthines in tea samples by capillary electrochromatography

In this paper, the simultaneous separation of several polyphenols such as (+)‐catechin, (–)‐epicatechin, (–)‐epigallocatechin, theophylline, caffeine in green and black teas by capillary electrochromatography (CEC) was developed. Several experimental parameters such as stationary phase type, mobile phase composition, buffer and pH, inner diameter of the columns, sample injection, were evaluated to obtain the complete separation of the analysed compounds. Baseline resolution of the studied polyphenols was achieved within 30 min by using a capillary column (id 100 μm) packed with bidentate C₁₈ particles for 24.5 cm and a mobile phase composed of 5 mM ammonium acetate buffer pH 4 with H₂O/ACN (80:20, v/v). The applied voltage and the temperature were set at 30 kV and 20°C. Precision, detection and quantification limits, linearity, and accuracy were investigated. A good linearity (R² > 0.9992) was achieved over a concentration working range of 2–100 μg/mL for all the analytes. LOD and LOQ were 1 and 2 μg/mL, respectively, for all studied compounds. The CEC method was applied to the analysis of those polyphenols in green and black tea samples after an extraction procedure. Good recovery data from accuracy studies ranged between 90% and 112% for all analytes.     

Separation and determination of flavonoids using microemulsion EKC with electrochemical detection

A selective and sensitive method of microemulsion EKC (MEEKC) with electrochemical detection (ED) was developed for separation and determination of 14 flavonoids. In order to obtain the better stability for the studied flavonoids, oil (ethyl acetate) with low interfacial surface tension was employed as organic solvent. A running buffer composed of 0.9% (w/v, 30 mM) SDS, 0.9% (w/v, 21 mM) sodium cholate (SC), 0.9% (w/v, 121 mM) butan-1-ol, 0.6% (w/v, 68 mM) ethyl acetate, and 98.2% v/v 10 mM Na(2)B(4)O(7)-20 mM H(3)BO(3) buffer (pH 7.5) was applied for the separation of flavonoids. Under the optimum conditions, the relationship between peak currents and analyte concentrations was linear over about 1.3 and 1.7 orders of magnitude with detection limits (defined as S/N = 3) ranging from 0.02 to 0.5 microg/mL for all analytes. This method was applied for the determination of flavonoids in real samples with simple extraction procedures, and the assay results were satisfactory.     

Separation of 5-Lipoxygenase Metabolites Using Cyclodextrin-Modified Microemulsion Electrokinetic Chromatography and Head Column Field-Amplified Sample Stacking

A cyclodextrin-modified microemulsion electrokinetic chromatography method employing head column field-amplified sample stacking was developed for the analysis of arachidonic acid metabolites of the lipoxygenase pathways. The influence of the concentration of boric acid, the surfactant sodium dodecyl sulfate, the co-surfactant 1-butanol and the oil phase octane as well as the pH of the background electrolyte, the separation voltage and the separation temperature was studied. The optimized microemulsion consisting of 20 mM boric acid buffer, pH 9.0, 3.0 % (m/v) sodium dodecyl sulfate, 0.5 % (v/v) octane, 5.0 % (v/v) 1-butanol and 15 mM α-cyclodextrin enabled the separation of 20-hydroxy-leukotriene B₄, leukotriene B₄, 6-trans-leukotriene B₄, 6-trans-12-epi-leukotriene B₄, 5(S)-hydroxy-6-trans-8,11,14-cis-eicosatetraenoic acid, 12(S)-hydroxy-5,8,14-cis-10-trans-eicosatetraenoic acid, 15(S)-hydroxy-5,8,11-cis-13-trans-eicosatetraenoic acid as well as the internal standard prostaglandin B₁ in <10 min employing a separation voltage of 17.5 kV at a temperature of 23 °C. A matrix peak from solid-phase extraction sample workup co-migrated with 5(S)-hydroxy-6-trans-8,11,14-cis-eicosatetraenoic acid affecting peak integration. The addition of 5 % (v/v) 2-propanol to the microemulsion resulted in the separation of this eicosatetraenoic acid and the matrix components at the expense of analysis time and peak resolution between the diastereomers 6-trans-leukotriene B₄ and 6-trans-12-epi-leukotriene B₄. In summary, the MEEKC method appeared to be especially suitable for the more polar arachidonic acid metabolites.     

Hemoglobin‐Titanate Composite Based Biosensor for the Amperometric Determination of Hydrogen Peroxide in Acidic Medium

A hemoglobin‐titanate composite based biosensor was chosen for determination of H₂O₂ in an acidic medium. CV results of the Hb‐titanate modified pyrolytic graphite electrode showed a pair of well‐defined, quasi‐reversible redox peaks centered at ?246 mV (vs. Ag/AgCl) in a pH 5.0 HAc‐NaAc buffer solution. The modified electrode exhibited good electrocatalytic response for monitoring H₂O₂ and had a large linear detection range from 20 μM to 3.2 mM with a detection limit of 8 μM (S/N=3) and a sensitivity of 29.7 mA M^?1 cm^?2 in the pH 5.0 solution. The biosensor also possessed good long term storage stability.     

Direct Electrochemistry of Hemoglobin Entrapped in Composite Electrodeposited Chitosan‐Multiwall Carbon Nanotubes and Nanogold Particles Membrane and Its Electrocatalytic Application

Hemoglobin was entrapped in composite electrodeposited chitosan‐multiwall carbon nanotubes (MCNTs) film by assembling gold nanoparticles and hemoglobin step by step. In phosphate buffer solution (pH 7), a pair of well‐defined and quasireversible redox peaks appeared with formal potential at ?0.289 V and peak separation of 100 mV. The redox peaks respected for the direct electrochemistry of hemoglobin at the surface of chitosan‐MCNTs‐gold nanoparticles modified electrode. The parameters of experiments have also been optimized. The composite electrode showed excellent electrocatalysis to peroxide hydrogen and oxygen, the peak current was linearly proportional to H₂O₂ concentration in the range from 1×10^?6 mol/L to 4.7×10^?4 mol/L with a detection limit of 5.0×10^?7 mol/L, and this biosensor exhibited high stability, good reproducibility and better selectivity. The biosensor showed a Michaelis–Menten kinetic response as H₂O₂ concentration is larger than 5.0×10^?4 mol/L, the apparent Michaelis–Menten constant for hydrogen peroxide was calculated to be 1.61 μmol/L.     

Determination of Palmatine in Rabbit Plasma by RP-HPLC with Solid-Phase Extraction

A rapid and specific reversed-phase high performance liquid chromatography (RP-HPLC) method for the determination of palmatine in rabbit plasma has been developed and validated. The chromatographic separation was performed on a C₁₈ column at 40 °C. The mobile phase, delivered at 1.0 mL min^?1, consisted of acetonitrile/phosphate buffer (pH 3.0) 40:60 (v/v). The detection wavelength was set at 345 nm. Palmatine and internal standard (IS) berberine were extracted from plasma by solid-phase extraction using C18 cartridges. Linearity was confirmed in the concentration range of 0.01 to 5 μg mL^?1, the inter-day and intra-day RSDs were within 10.0, the recoveries of palmatine ranged from 93.1 to 110.3, and the limit of detection (LOD, S/N > 3) was 0.002 μg mL^?1. The method is applicable to the determination of palmatine in rabbit plasma after intravenous administration of palmatine.     

Nonaqueous capillary electrophoresis with laser-induced fluorescence detection: a case study of comparison with aqueous media

A novel method based on separation by nonaqueous capillary electrophoresis (NACE) combined with laser-induced fluorescence (LIF) detection was developed and compared with classic aqueous modes of electrophoresis in terms of resolution of solutes of interest and sensitivity of the fluorescence detection. Catecholamines derivatized with 4-chloro-7-nitro-2,1,3-benzoxadiazole (NBD-Cl) were chosen as test analytes for their subtle fluorescence properties. In aqueous systems, capillary zone electrophoresis (CZE) was not suitable for the analysis of test analytes due to complete fluorescence quenching of NBD-labeled catecholamines in neat aqueous buffer. The addition of micelles or microemulsion droplets into aqueous running buffer can dramatically improve the fluorescence response, and the enhancement seems to be comparable for micellar electrokinetic chromatography (MEKC) and microemulsion electrokinetic chromatography (MEEKC). As another alternative, NACE separation was advantageous when performing the analysis under the optimum separation condition of 20 mM sodium tetraborate, 20 mM sodium dodecyl sulfate (SDS), 0.1% (v/v) glacial acetic acid, 20% (v/v) acetonitrile (ACN) in methanol medium after derivatization in ACN/dimethyl sulfoxide (DMSO) (3:2, v/v) mixed aprotic solvents containing 20 mM ammonium acetate. Compared with derivatization and separation in aqueous media, NACE-LIF procedure was proved to be superior, providing high sensitivity and short migration time. Under respective optimum conditions, the NACE procedure offered the best fluorescence response with 5-24 folds enhancement for catecholamines compared to aqueous procedures. In addition, the mechanisms of derivatization and separation in nonaqueous media were elucidated in detail.     

LC-DAD Determination of Calcium Channel Blockers by Using an Experimental Design Approach

A high-performance liquid chromatographic method with diode array detection has been developed for the determination of five 1,4-dihydropyridines: amlodipine, nitrendipine, felodipine, lacidipine and lercanidipine. A fractional design and a central composite design were used. The factors considered in the optimisation process were: percentage of organic modifier, pH of the aqueous buffer, buffer concentration and temperature. The chromatographic separation was performed using a Supelcosil LC-ABZ+Plus C18 column. An optimised mobile phase of acetonitrile-water (70:30, v/v), containing 10 mM CH₃COOH-CH₃COONa pH 5 at a flow rate of 1 mL min^?1 was used. The temperature was set at 30 ± 2 °C. The photometic detection was carried out at 237 nm. The method was applied to the determination of these compounds at μg mL^?1 concentration levels, obtaining intraday repeatabilities values lower than 5% in terms of relative standard deviations, accuracies higher than 98% and detection limits ranged from 0.03 (felodipine) to 0.35 μg mL^?1 (lacidipine). The chromatographic method allowed the analysis of the drugs in their pharmaceutical formulations with a total elution time of 12 min.     

Efficient separation of tanshinones by polyvinylpyrrolidone‐stabilized graphene‐modified micellar electrokinetic chromatography

In this work, a PVP‐stabilized graphene was used in MEKC for the separation of tanshinones. Seven structurally similar tanshinones were studied, that is, tanshinone IIB, dihydrotanshinone I, tanshinone I, cryptotanshinone, 1,2‐dihydrotanshinone I, miltirone, and tanshinone IIA. To achieve optimal conditions, graphene concentration, sample solvent composition, SDS concentration, 2‐propanolconcentration, and buffer pH were investigated. At a separation voltage of 30 kV and a 41.5 cm effective length fused‐silica capillary, good resolution within 12 min was performed using 10 mM borate buffer (pH 9.3) containing 30 mM SDS, 10% v/v 2‐propanol and 6 μg/mL graphene. The method was validated in terms of linearity (r² > 0.9970), intra‐ and inter‐day precision were less than 3.56 and 4.83%, respectively. The proposed method was then successfully applied to Danshentong capsule, an herbal preparation from Salvia miltiorrhiza. Our results indicated the high separation efficiency of PVP‐stabilized graphene provided new opportunities for the analysis of complex samples.     

High performance liquid chromatographic determination of butamyrate citrate in pharmaceutical preparation

An HPLC method was developed and validated for the determination of butamyrate citrate. The HPLC separation was achieved on a diol column (300 × 4.6 mm) packed with 5.0 μm particle size using a mobile phase of ammonium acetate buffer (pH = 6.5) and methanol (750:250, v/v) at a flow rate of 1.4 ml min^?1. The UV detector was operated at 225 nm. The method was validated for specificity, linearity, precision, accuracy and robustness. The retention time was 5.9 min. The proposed method provided linear responses within the concentration range 75–225 μg ml^?1 with LOD and LOQ values of 0.69 and 2.29 μg ml^?1, respectively. Correlation coefficient (r) of the regression equation was 0.9999. The method was found to be precise, accurate, and reproducible.