CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Adsorption of iso-butane on ZnO(0 0 0 1)-Zn

Presented are thermal desorption spectroscopy (TDS) and adsorption probability measurements of iso-butane on the Zn-terminated surface of ZnO. The initial adsorption probability, S₀, decreases linearly from 0.57 to 0.22 (±0.02) with impact energy, E_i = 0.74-1.92 eV, and is independent of adsorption temperature, T_s = 91-114 K (±5 K), indicating non-activated molecular adsorption. The coverage, Θ, dependent adsorption probabilities, S(Θ), show a cross-over from adsorbate-assisted adsorption (S increases with Θ) to Kisliuk-like dynamics at about the desorption temperature of iso-butane bi-layers (∼110 K). Thus, the adsorption dynamics are precursor-mediated. The enhanced (gas-surface) mass-match, caused by forming a second layer of the alkane, leads to adsorbate-assisted adsorption. A direct fitting procedure of the TDS data yields a pre-exponential factor of 2.5 × 10¹³/s and a coverage dependent heat of adsorption of E_d(Θ) = 39 − 6 ∗ Θ + 2.5 ∗ exp(−Θ/0.07) kJ/mol.     

Surface structure of K/Pd(1 0 0) and the effect of H coadsorption: Density functional theory calculations

We have performed density-functional theory calculations to study the atomic structure of the K/Pd(1 0 0)-p(2 × 2) and -c(2 × 2) surfaces formed at 0.25 ML and 0.5 ML, respectively. We find that K atoms prefer the hollow site with the K adsorption height 2.44 Å for p(2 × 2) and 2.50 Å c(2 × 2). The first interlayer spacing (d₁₂) of the Pd(1 0 0) substrate appears slightly contracted from the bulk value as Δd₁₂ = −0.8% and −0.3% for p(2 × 2) and c(2 × 2), respectively. The calculated contraction Δd₁₂ = −0.3% for c(2 × 2) is not in accord with the expansion Δd₁₂ = +1.3% reported by a low-energy electron diffraction (LEED) study. As the origin of this difference, a possibility of hydrogen contamination of the surface sample used in the LEED study is suggested: Our calculations show that the d₁₂ of K/Pd(1 0 0)-c(2 × 2) increases linearly with the coverage of H coadsorption, which leads to an estimation for the H coverage of the surface sample as 0.1-0.4 ML.     

First principle calculations of benzotriazole adsorption onto clean Cu(1 1 1)

The adsorption of benzotriazole (BTAH or C₆N₃H₅) on a Cu(1 1 1) surface is investigated by using first principle density functional theory calculations (VASP). It is found that BTAH can be physisorbed (<0.1 eV) or weakly chemisorbed (∼0.43 eV) onto Cu(1 1 1), and the chemical bond is formed through nitrogen sp² lone pairs. The weak chemisorption can be stabilized by reaction with neighboring protonphilic radicals, like OH⁻. Furthermore, the geometries and associated energies of intermolecular hydrogen bonds between adsorbates on Cu(1 1 1) are also calculated. A model of the first layer of BTAH/BTA⁻ on Cu(1 1 1) surface is developed based on a hydrogen bond network structure.     

Density functional theory study of hydrogenation mechanism in Fe-doped Mg(0 0 0 1) surface

Using density functional theory (DFT) in combination with nudged elastic band (NEB) method, the dissociative chemisorptions and diffusion processes of hydrogen on both pure and Fe-doped Mg(0 0 0 1) surfaces are studied. Firstly, the dissociation pathway of H₂ and the relative barrier were investigated. The calculated dissociation barrier (1.08 eV) of hydrogen molecule on a pure Mg(0 0 0 1) surface is in good agreement with comparable experimental and theoretical studies. For the Fe-doped Mg(0 0 0 1) surface, the activated barrier decreases to 0.101 eV due to the strong interaction between the s orbital of H and the d orbital of Fe. Then, the diffusion processes of atomic hydrogen on pure and Fe-doped Mg(0 0 0 1) are presented. The obtained diffusion barrier to the first subsurface is 0.45 eV and 0.98 eV, respectively. Finally, Chou method was used to investigate the hydrogen sorption kinetic mechanism of pure MgH₂ and Mg mixed with 5 at.% Fe atoms composites. The obtained activation energies are 0.87 ± 0.02 and 0.31 ± 0.01 eV for H₂ dissociation on the pure surface and H atom diffusion in Fe-doped Mg surfaces, respectively. It suggests that the rate-controlling step is dissociation of H₂ on the pure Mg surface while it is diffusion of H atom in the Fe-doped Mg surface. And both of fitting data are matching well with our calculation results.     

Adsorption of water on TiN (1 0 0), (1 1 0) and (1 1 1) surfaces: A first-principles study

We use first-principles density functional theory-based calculations in the analysis of the interaction of H₂O with (1 0 0), (1 1 0) and (1 1 1) surfaces of TiN, and develop understanding in terms of surface energies, polarity of the surface and chemistry of the cation, through comparison with H₂O adsorption on ZrN. While water molecule physisorbs preferentially at Ti site of (1 0 0) and (1 1 1) surfaces, it adsorbs dissociatively on (1 1 0) surface of TiN with binding stronger than almost 1.32 eV/molecule. Our analysis reveals the following general trends: (a) surfaces with higher energies typically lead to stronger adsorption, (b) dissociative adsorption of H₂O necessarily occurs on a charge neutral high energy surface and (c) lower symmetry of the (1 1 0) plane results in many configurations of comparable stability, as opposed to the higher symmetry (1 0 0) and (1 1 1) surfaces, which also consistently explain the results of H₂O adsorption on MgO available in literature. Finally, weaker adsorption of H₂O on TiN than on ZrN can be rationalized in terms of greater chemical stability of Ti arising from its ability to be in mixed valence.     

SiO adsorption on a p(2 × 2) reconstructed Si(1 0 0) surface

We have investigated the adsorption mechanism of SiO molecule incident on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. Stable adsorption geometries of SiO on Si surface, as well as their corresponding activation and adsorption energies are identified. We found that the SiO molecule is adsorbed on the Si(1 0 0) surface with almost no activation energy. An adsorption configuration where the SiO binds on the channel separating the dimer rows, forming a Si-O-Si bridge on the surface, is the energetically most favourable geometry found. A substantial red-shift in the calculated vibrational frequencies of the adsorbed SiO molecule in the bridging configurations is observed. Comparison of adsorption energies shows that SiO adsorption on a Si(1 0 0) surface is energetically less favourable than the comparable O₂ adsorption. However, the role of SiO in the growth of silicon sub-oxides during reactive magnetron plasma deposition is expected to be significant due to the relatively large amount of SiO molecules incident on the deposition surface and its considerable sticking probability. The stable adsorption geometries found here exhibit structural properties similar to the Si/SiO₂ interface and may be used for studying SiO_x growth.     

Density functional study of hypophosphite adsorption on Ni (1 1 1) and Cu (1 1 1) surfaces

Surface structures and electronic properties of hypophosphite, H₂PO₂⁻, molecularly adsorbed on Ni(1 1 1) and Cu(1 1 1) surfaces are investigated in this work by density functional theory at B3LYP/6-31++g(d, p) level. We employ a four-metal-atom cluster as the simplified model for the surface and have fully optimized the geometry and orientation of H₂PO₂⁻ on the metal cluster. Six stable orientations have been discovered on both Ni (1 1 1) and Cu (1 1 1) surfaces. The most stable orientation of H₂PO₂⁻ was found to have its two oxygen atoms interact the surface with two PO bonds pointing downward. Results of the Mulliken population analysis showed that the back donation from 3d orbitals of the transition metal substrate to the unfilled 3d orbital of the phosphorus atom in H₂PO₂⁻ and 4s orbital's acceptance of electron donation from one lone pair of the oxygen atom in H₂PO₂⁻ play very important roles in the H₂PO₂⁻ adsorption on the transition metals. The averaged electron configuration of Ni in Ni₄ cluster is 4s^0.634p^0.023d^9.35 and that of Cu in Cu₄ cluster is 4s^1.004p^0.033d^9.97. Because of this subtle difference of electron configuration, the adsorption energy is larger on the Ni surface than on the Cu surface. The amount of charge transfers due to above two donations is larger from H₂PO₂⁻ to the Ni surface than to the Cu surface, leading to a more positively charged P atom in Ni_nH₂PO₂⁻ than in Cu_nH₂PO₂⁻. These results indicate that the phosphorus atom in Ni_nH₂PO₂⁻ complex is easier to be attacked by a nucleophile such as OH⁻ and subsequent oxidation of H₂PO₂⁻ can take place more favorably on Ni substrate than on Cu substrate.     

The adsorption of methylcyclopentane on Pt(1 1 1)

The adsorption of methylcyclopentane (MCP) on Pt(1 1 1) has been studied using the atom superposition and electron delocalization (ASED-MO) molecular orbital method. Results show a weak interaction with the metallic surface. The adsorption energy is rather independent of the adsorption site coordination number. We find that Pt 6s, 6p_z and 5d_z² orbitals are involved in the bonding with MCP. There is no bonding between the carbon ring and the Pt surface and the interaction comes from the hydrogen atoms to the surface.     

Shell model calculations of the adsorption and diffusion of K, Cl, and KCl on KCl(0 0 1)

Equilibrium adsorption positions and diffusion pathways of the ions K⁺ and Cl⁻ as well as of the molecule KCl on the terrace of the (0 0 1) surface of KCl were determined by shell model calculations allowing relaxations of the crystal lattice in the vicinity of the adsorbed species. For the ions each one adsorption position was found, in which the ions are located above the hollow site at the center of a slightly distorted square formed by two cations and two anions of the uppermost surface layer of the KCl crystal. Adsorption energies of −1.52 eV for K⁺ and −1.61 eV for Cl⁻ were calculated. Jumps of the ions occur from these positions to adjacent hollow positions in the ±[1 0 0] and ±[0 1 0] directions with a jump distance of a₀/2. The activation energies for the jumps result as 0.142 for K⁺ and 0.152 eV for Cl⁻ and the mean diffusion lengths as and . For the KCl molecule four distinct adsorption minima with energies between −0.932 and −0.825 eV were found. Because of the smaller lattice relaxation caused by the molecule the adsorption energies are considerably lower than for the single ions. In the position with the largest adsorption energy the ions of the admolecule are again placed above adjacent hollow sites. In two more adsorption positions only one ion is at the hollow site and the other one in a top position above an oppositely charged ion of the surface. In the fourth position with the smallest adsorption energy both ions are in top positions. Jumps between the different adsorption positions proceed by rotations of the molecule, in which one of its ions remains essentially attached to a local minimum position. The diffusion and desorption of a KCl molecule was studied by a Monte Carlo method, resulting in a mean diffusion length x_s (nm) = 0.39 exp[0.84 (eV)/2kT], which agrees rather well with an experimental value of . Values for the mean stay time as well as for the surface diffusion coefficient are derived.     

RAIRS studies of CO adsorption on Pd/CeO2−x(1 1 1)/Pt(1 1 1)

Reflection absorption infrared spectroscopy (RAIRS) has been used to investigate the adsorption of CO on CeO_2−x-supported Pd nanoparticles at room temperature. The results show that when CeO_2−x is initially grown on Pt(1 1 1), a small proportion of the surface remains as bare Pt sites. However, when Pd is deposited onto CeO_2−x/Pt(1 1 1), most of the Pd grows directly on top of the CeO_2−x(1 1 1). RAIR spectra of CO adsorption on 1 ML Pd/CeO_2−x/Pt(1 1 1) show a broad CO-Pd band, which is inconsistent with a single crystal Pd surface. However, the 5 ML and 10 ML Pd/CeO_2−x/Pt(1 1 1) spectra show vibrational bands consistent with the presence of Pd(1 1 1) and (1 0 0) faces, suggesting the growth of Pd nanostructures with well defined facets.     

Comparative study of the GaAs(1 0 0) surface cleaned by atomic hydrogen

In attempt to correlate electronic properties and chemical composition of atomic hydrogen cleaned GaAs(1 0 0) surface, high-resolution photoemission yield spectroscopy (PYS) combined with Auger electron spectroscopy (AES) and mass spectrometry has been used. Our room temperature investigation clearly shows that the variations of surface composition and the electronic properties of a space charge layer as a function of atomic hydrogen dose display three successive interaction stages. There exists a contamination etching stage which is observed up to around 250 L of atomic hydrogen dose followed by a transition stage and a degradation stage which is observed beyond 700 L of exposure. In the first stage, a linear shift in the surface Fermi level is observed towards the conduction band by 0.14 eV, in agreement to the observed restoration of the surface stoichiometry and contamination removal. The next stage is characterized by a drop in ionization energy and work function, which quantitatively agrees with the observed Ga-enrichment as well as the tail of the electronic states attributed to the breaking As-dimers. As a result of the strong hydrogenation, the interface Fermi level E_F − E_v has been pinned at the value of 0.75 eV what corresponds to the degradation stage of the GaAs(1 0 0) surface that exhibits metallic density of states associated with Ga_As antisites defects. The results are discussed quantitatively in terms of the surface molecule approach and compared to those obtained by other groups.     

Theoretical study of CO and Pb adsorption on the Ni(1 1 1) and Ni3Al(1 1 1) surfaces

Adsorption of CO molecules and Pb atoms on the Ni(1 1 1) and Ni₃Al(1 1 1) substrates is studied theoretically within an ab initio density-functional-theory approach. Stable adsorption sites and the corresponding adsorption energies are first determined for stoichiometric surfaces. The three-fold hollow sites (fcc for Pb and hcp for CO) are found most favourable on both substrates. Next, the effect of surface alloying by a substitution of selected topmost substrate atoms by Pb or Ni atoms on the adsorption characteristics is investigated. When the surface Al atoms of the Ni₃Al(1 1 1) substrate are replaced by Ni atoms, the Pb and CO adsorption energies approach those for a pure Ni(1 1 1) substrate. The Pb alloying has a more substantial effect. On the Ni₃Al(1 1 1) substrate, it reduces considerably adsorption energy of CO. On the Ni(1 1 1) substrate, CO binding strengthens slightly upon the formation of the Ni(1 1 1)p(2×2)-Pb surface alloy, whereas it weakens drastically when the Ni(1 1 1)-Pb surface alloy is formed.     

Ruthenium adsorption and diffusion on the GaN(0 0 0 1) surface

We report first principles calculations to analyze the ruthenium adsorption and diffusion on GaN(0 0 0 1) surface in a 2×2geometry. The calculations were performed using the generalized gradient approximation (GGA) with ultrasoft pseudopotential within the density functional theory (DFT). The surface is modeled using the repeated slabs approach. To study the most favorable ruthenium adsorption model we considered T₁, T₄ and H₃ special sites. We find that the most energetically favorable structure corresponds to the Ru- T₄ model or the ruthenium adatom located at the T₄ site, while the ruthenium adsorption on top of a gallium atom (T₁ position) is totally unfavorable. The ruthenium diffusion on surface shows an energy barrier of 0.612 eV. The resultant reconstruction of the ruthenium adsorption on GaN(0 0 0 1)- 2×2 surface presents a lateral relaxation of some hundredth of Å in the most stable site. The comparison of the density of states and band structure of the GaN(0 0 0 1) surface without ruthenium adatom and with ruthenium adatom is analyzed in detail.     

Effects of N adsorption on the structural and electronic properties of SrTiO3(0 0 1) surface

The atomic configurations, bonding characteristics, and electronic structures of the N-adsorbed (directly and substitutionally) SrTiO₃(0 0 1) surface are studied by using first-principles method based on the density functional theory. From the analysis of the energetics and density of states, it is found that the stability of the directly adsorbed N depends on the relative position of N atom to the surface. To better understand the effects of the substitutionally adsorbed N on the surface, as an example, the behavior of Au atoms adsorbed on the N-substituted surface is discussed in detail. There is clearly a synergy effect between the substitution of N for O_s(I) and the adsorption of Au atoms on the SrTiO₃(0 0 1) surface.     

Atomic and electronic structures of thin NaCl films grown on a Ge(0 0 1) surface

Density functional theory (DFT) with LDA and GGA have been employed to study the interface and thin film properties of NaCl on a Ge(0 0 1) surface. The atomic and electronic structures of thin NaCl films from one to ten monolayers were analyzed. The layer adsorption energies show that a quasi-crystalline (0 0 1) fcc NaCl film is built up via a layer-by-layer growth mode with NaCl thickness above 2 ML. Simulated STM images show a well-resolved (1 × 1) NaCl atomic structure for sample bias voltage V_s < −2.5 V and the bright protrusions should be assigned to the Cl⁻ ions of the NaCl film. The Ge substrate dimer is reserved and buckled like a clean Ge(0 0 1)-p(2 × 2) surface as the result of weak interface interaction between the dangling bonds coming from valence π states of the Ge substrate and the 3p states of the interfacial Cl⁻ ion. These results are consistent with the experiments of STM, LEED and EELS.     

The effect of ferroelectric polarization on the interaction of water and methanol with the surface of LiNbO3(0 0 0 1)

Water and methanol temperature programmed desorption (TPD) measurements were performed on the positive (c⁺) and negative (c⁻) surfaces of poled ferroelectric lithium niobate (LiNbO₃) single crystals. The results indicate that the molecule-surface interactions are both coverage and polarization-dependent. From a comparison of the TPD spectra for the positive and negative surfaces, it is shown that the desorption temperatures of water and methanol are consistently lower on the negative surface by 15 K and 20 K, respectively. The TPD spectra were simulated using the Polanyi-Wigner equation with a coverage-dependent energy term. These calculations show that the polarization dependence of the desorption temperature is due to a difference in the zero-coverage desorption energies on the two surfaces equal to a few kJ per mole. The mechanism for the polarization effect is explored with in situ pyroelectric voltage measurements, which indicate that a surface voltage of ±2 mV develops in the LiNbO₃(0 0 0 1) samples during TPD measurements. The magnitude of the pyroelectric-induced surface charge is heating rate dependent.     

The influence of hydrogen on the electronic and magnetic structures of TM(0 0 1) (TM=Fe, Co, Ni, and Cu) surfaces and interfaces: Ab-initio calculations

We present ab-initio investigation of the electronic and magnetic structure of TM(0 0 1) surfaces and TM/Cu(0 0 1) systems (TM=Fe, Co, Ni, Cu) with and without hydrogen adsorbed layer. The adsorption energy of hydrogen atom is found to be energetically more stable above the surface layer of Ni(0 0 1) surface than other TM(0 0 1) surfaces. The adsorption energies of hydrogen on TM/Cu(0 0 1) systems are larger than those on TM(0 0 1) surfaces. The relaxed geometries show that hydrogen has a strong influence on the interlayer distance. Furthermore, a marked reduction of Fe, Co, and Ni surface magnetic moments to 2.54, 1.41 and 0.25 μ_B, respectively, is obtained due to the presence of hydrogen.     

Cu adsorption on pyrite (1 0 0): Ab initio and spectroscopic studies

Surface optimised S 2p photoelectron spectra show that both surface S²⁻ monomers and (S-S)²⁻ dimers are present at pyrite (1 0 0) fracture surfaces. In order to determine which sulfur species are involved in Cu adsorption, fresh pyrite surfaces were exposed to Cu²⁺ in solution. The S 2p spectra suggest that both types of S surface species are involved in the mechanism of Cu adsorption (activation). Ab initio density functional theory was used to model Cu adsorbed onto pyrite (1 0 0) to support the interpretation of the spectroscopy. Mulliken population analysis confirms the charge distribution suggested by the core line shifts as observed in the photoelectron spectra. The ab initio calculations were consistent with a two-coordinate bond between Cu(I), a surface S monomer and a surface S dimer.     

CO methanation on Ni(1 1 1) and modified Ni3Al(1 1 1) surfaces: A first-principle study

The adsorption energies of intermediates in CO methanation on the modified Ni₃Al(1 1 1) surface and the Ni(1 1 1) surface are calculated using density functional theory. A microkinetic analysis based on the calculated adsorption energies is performed to explain the different kinetics of CO methanation catalyzed by Ni₃Al and Ni powders. The electronic structures of different atoms on the modified Ni₃Al surface are also presented, and correlate well with the adsorption energies and geometries.