Density functional study of oxygen adsorption on the Mg3Nd (0 0 1) surface

The adsorption of oxygen atoms on Mg₃Nd (0 0 1) surface was studied based on density function theory (DFT), in which the exchange-correlation potential was chosen as the generalized gradient approximation (GGA) in the Perdew and Wang (PW91). The most preferred adsorption position was at the top-hollow site. Upon the optimization on top-hollow site with different coverage, it was found that the adsorption energy decreased with oxygen coverage. The density of states analysis showed that obvious charge transfer took place between O atom and the nearest Nd atom and chemical bond formed between O atom and the nearest Nd atom after O adsorption. The result of surface energy as a function of chemical potential change of oxygen indicated the clean Mg₃Nd (0 0 1) surface was easy to adsorb oxygen and form 1.00 ML surface.     

CO oxidation over Ru(0 0 0 1) at near-atmospheric pressures: From chemisorbed oxygen to RuO2

RuO₂(1 1 0) was formed on Ru(0 0 0 1) under oxygen-rich reaction conditions at 550 K and high pressures. This phase was also synthesized using pure O₂ and high reaction temperatures. Subsequently the RuO₂ was subjected to CO oxidation reaction at stoichiometric and net reducing conditions at near-atmospheric pressures. Both in situ polarization modulation infrared reflection absorption spectroscopy (PM-IRAS) and post-reaction Auger electron spectroscopy (AES) measurements indicate that RuO₂ gradually converts to a surface oxide and then to a chemisorbed oxygen phase. Reaction kinetics shows that the chemisorbed oxygen phase has the highest reactivity due to a smaller CO binding energy to this surface. These results also show that a chemisorbed oxygen phase is the thermodynamically stable phase under stoichiometric and reducing reaction conditions. Under net oxidizing conditions, RuO₂ displays high reactivity at relatively low temperatures (?450 K). We propose that this high reactivity involves a very reactive surface oxygen species, possibly a weakly bound, atomic oxygen or an active molecular O₂ species. RuO₂ deactivates gradually under oxidizing reaction conditions. Post-reaction AES measurements reveal that this deactivation is caused by a surface carbonaceous species, most likely carbonate, that dissociates above 500 K.     

First-principles study of indium on silicon (1 0 0)—the structure, defects and interdiffusion

The atomic structures of indium (In) on silicon (Si) (1 0 0)-(2 × 1) surface are investigated by the local density approximation using first-principles pseudopotentials. Total energy optimizations show that the energetically favored structure is the parallel ad-dimer model. The adsorption energy of In on ideal Si(1 0 0)-(1 × 1) surface is significantly higher than that on reconstructed Si(1 0 0)-(2 × 1) surface, suggesting that In adsorption does not break the Si-Si dimer bond of the substrate. When Si surface contains single dimer vacancy defects, In chain will be interrupted, leading to disconnected In nanowires. Displacive adsorption of In on Si(1 0 0) is also considered, and the calculation suggests that interdiffusion of In into Si substrate will not be favorable under equilibrium conditions.     

Low temperature adsorption of oxygen on reduced V2O3(0 0 0 1) surfaces

Well ordered V₂O₃(0 0 0 1) films were prepared on Au(1 1 1) and W(1 1 0) substrates. These films are terminated by a layer of vanadyl groups under typical UHV conditions. Reduction by electron bombardment may remove the oxygen atoms of the vanadyl layer, leading to a surface terminated by vanadium atoms. The interaction of oxygen with the reduced V₂O₃(0 0 0 1) surface has been studied in the temperature range from 80 to 610 K. Thermal desorption spectroscopy (TDS), infrared reflection absorption spectroscopy (IRAS), high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) were used to study the adsorbed oxygen species. Low temperature adsorption of oxygen on reduced V₂O₃(0 0 0 1) occurs both dissociatively and molecularly. At 90 K a negatively charged molecular oxygen species is observed. Upon annealing the adsorbed oxygen species dissociates, re-oxidizing the reduced surface by the formation of vanadyl species. Density functional theory was employed to calculate the structure and the vibrational frequencies of the O₂ species on the surface. Using both cluster and periodic models, the surface species could be identified as η²-peroxo () lying flat on surface, bonded to the surface vanadium atoms. Although the O-O vibrational normal mode involves motions almost parallel to the surface, it can be detected by infrared spectroscopy because it is connected with a change of the dipole moment perpendicular to the surface.     

Room-temperature-adsorption behavior of acetic anhydride on a TiO2(1 1 0) surface

We have studied the adsorption structure of acetic anhydride on a TiO₂(1 1 0) surface using XPS (X-ray photoelectron spectroscopy), LEED (low energy electron diffraction) and HREELS (high resolution electron energy loss spectroscopy) to determine the origins of the unique adsorption properties of carboxylic acids on a TiO₂(1 1 0) surface. The C 1s XPS data indicated that the saturation carbon amount of adsorbed acetic anhydride was 12 ± 3% larger than that of the adsorbed acetic acid. LEED showed p(2 × 1) weak spots for the acetic anhydride adsorbed surface. The HREELS spectra revealed the dissociative adsorption of acetic anhydride. Based on these findings, we concluded that the neutralization of the bridging oxygen atoms associated with the dissociative adsorption is necessary for the stable adsorption of carboxylates on the 5-fold Ti sites.     

First-principles study on the catalytic role of Ag in the oxygen adsorption of LaMnO3(0 0 1) surface

In the present paper, the catalytic role of Ag in the oxygen adsorption of LaMnO₃(0 0 1) surface has been theoretically investigated using first-principles calculations based on the density functional theory (DFT) and pseudopotential method. The O₂ adsorption energy is larger for the vertical adsorption and the covalent bond was formed between O₂ molecule and surface Mn. The calculation of electronic properties of interaction between Ag atom and LaMnO₃(0 0 1) surface demonstrates that the most stable position for Ag adsorption is hollow site. The O₂ adsorption energy dramatically increased from 0.298 eV to 1.108 eV due to Ag pre-adsorbed. It is Ag pre-adsorbed that facilitates O₂ adsorption on surface. The bond length and bond population of O₂ molecule indicate that Ag atom facilitates O₂ molecule dissociative adsorption. The Ag atom strengthens LaMnO₃(0 0 1) substrate activity and activity center was formed on surface, which enhances the electrocatalytic activity of LaMnO₃ as solid oxide fuel cells cathode material at low temperature.     

Structural properties of oxygen on InN(0 0 0 1) surface

First-principles calculations are performed to study the various structures of oxygen (O) adsorbed on InN(0 0 0 1) surfaces. It is found that the formation energy of O on InN(0 0 0 1) decreases with decreasing oxygen coverage. Of all the adsorbate induced surface structures examined, the structure of InN(0 0 0 1)-(2 × 2) as caused by O adsorption at the H₃ sites with 0.25 monolayers coverage is most energetically favorable. Meanwhile, nitrogen (N) vacancy can form spontaneously. Oxygen atoms may also substitute N atoms, or accumulate at the voids inside InN film or simply stay on the surface during growth. The oxygen impurity then acts as a potential source for the n-type conductivity of InN as well as the large energy band gap measured.     

Deoxygenation of IrO2(1 1 0) surface: Core-level spectroscopy and density functional theory calculation

Deoxygenation of the IrO₂(1 1 0) surface is investigated at 403-493 K, using the core-level spectroscopy and density functional theory (DFT) calculation. The Ir-4f_7/2 signals of 1f-cus-Ir with and without on-top oxygen (O_top) emerge as surface features of the baked-out surface, whose positive and negative shifts in binding energy are in line with the DFT computation results. Progressively increasing the reduction temperature, the 1f-cus-Ir feature quickly disappears and the signal of 2f-cus-Ir emerges at 403 K. Meanwhile the feature of 1f-cus-Ir + O_top diminishes but persists when the Ir metal signal is evident. The intriguing coexistence of 1f-cus-Ir + O_top and Ir metal at 433-443 K is elucidated in the theoretical pathway study. DFT calculation reveals that O₂ desorption via pairing two neighboring O_top atoms is the rate-determining step of surface deoxygenation. Under the UHV conditions, O_top is replenished via migration of the surface oxygen species, including the threefold coordinated oxygen (O_3f) of a reduced surface. Hence the O_top atom is an active and long-lived surface species, which does not vanish until O_3f is consumed and surface Ir begins to cluster. Under the realistic pressure conditions, O_top can also be refreshed via the dissociative adsorption of gas-phase oxygen. In either pathway, O_top is a critical intermediary of IrO₂(1 1 0) oxidation catalysis.     

A kinetic Monte Carlo/UBI-QEP model of O2 adsorption on fcc (1 1 1) metal surfaces

The previously developed kinetic Monte Carlo model of molecular oxygen adsorption on fcc (1 0 0) metal surfaces has been extended to fcc (1 1 1) surfaces. The model treats uniformly all elementary steps of the process—O₂ adsorption, dissociation, recombination, desorption, and atomic oxygen hopping—at various coverages and temperatures. The model employs the unity bond index—quadratic exponential potential (UBI-QEP) formalism to calculate coverage-dependent energetics (atomic and molecular binding energies and activation barriers of elementary steps) and a Metropolis-type algorithm including the Arrhenius-type reaction rates to calculate coverage- and temperature-dependent features, particularly the adsorbate distribution over the surface. Optimal values of non-energetic model parameters (the spatial constraint, a travel distance of “hot” atoms, attempt frequencies of elementary steps) have been chosen. Proper modifications of the fcc (1 0 0) model have been made to reflect structural differences in the fcc (1 1 1) surface, in particular the presence of two different hollow sites (fcc and hcp). Detailed simulations were performed for molecular oxygen adsorption on Ni(1 1 1). We found that at very low coverages, only O₂ adsorption and dissociation were effective, while O₂ desorption and O₂ and O diffusion practically did not occur. At a certain O + O₂ coverage, the O₂ dissociation becomes the fastest process with a rate one-two orders of magnitude higher than adsorption. Dissociation continuously slows down due to an increase in the activation energy of dissociation and due to the exhaustion of free sites. The binding energies of both molecular and atomic oxygen decrease with coverage, and this leads to greater mobility of atomic oxygen and more pronounced desorption of molecular oxygen. Saturation is observed when the number of adsorbed molecules becomes approximately equal to the number of desorbed molecules. Simulated coverage dependences of the sticking probability and of the atomic binding energy are in reasonable agreement with experimental data. From comparison with the results of the previous work, it appears that the binding energy profiles for Ni(1 1 1) and Ni(1 0 0) have similar shapes, although at any coverage the absolute values of the oxygen binding energy are higher for the (1 0 0) surface. For metals other than Ni, particularly Pt, the model projections were found to be too parameter-dependent and therefore less certain. In such cases further model developments are needed, and we briefly comment on this situation.     

Combined STM, LEED and DFT study of Ag(1 0 0) exposed to oxygen near atmospheric pressures

We have investigated the interaction of molecular oxygen with the Ag(1 0 0) surface in a temperature range from 130 K to 470 K and an oxygen partial pressure ranging up to 10 mbar by scanning tunneling microscopy, low electron energy diffraction, Auger electron spectroscopy and ab initio density functional calculations. We find that at 130 K, following oxygen exposures of 6000 Langmuirs O₂, the individual oxygen atoms are randomly distributed on the surface. When the sample is exposed to 10 mbar O₂ at room temperature, small, p(2 × 2) reconstructed patches are formed on the surface. After oxidation at ≈470 K and 10 mbar O₂ pressure the surface undergoes a c(4 × 6) reconstruction coexisting with a (6 × 6) superstructure. By ab initio thermodynamic calculations it is shown that the c(4 × 6) reconstruction is an oxygen adsorption induced superstructure which is thermodynamically stable for an intermediate range of oxygen chemical potential.     

Dissociation of water molecule at three-fold oxygen coordinated V site on the InVO4 (0 0 1) surface

Water molecule adsorption properties at the surface of InVO₄ have been investigated using an ab initio molecular dynamics approach. It was found that the water molecules were adsorbed dissociatively to the three-fold oxygen coordinated V sites on the (0 0 1) surface. The dissociative adsorption energy was estimated to be 0.8-0.9 eV per molecule. The equilibrium distance between V and O of the hydroxyl -OH was almost the same as the V-O distance of tetrahedra VO₄ in the InVO₄ bulk crystal (1.7-1.8 Å).     

First-principles studies on initial growth of Ni on MgO(0 0 1) surface

To elucidate the initial growth of metal on oxide surface, we studied adsorption of small nickel clusters, Ni_n (n = 1-5), on MgO(0 0 1) surface using first-principles method based on density-functional theory. It was found that the preferential adsorption site for an isolated Ni atom is directly above the surface oxygen atom. A strong covalent bond with partial ionic character is formed between the Ni adatom and the surface oxygen atom. Various structures were considered for the Ni_n isomers and 3D structures were found to be energetically more stable than 2D structures for clusters of more than two atoms. For the 2D clusters, metal-metal bonds prevail over metal-substrate bonds with increasing Ni coverage. The calculated work function and ionization energy were found to vary with Ni coverage which is attributed to the change of the surface dipole moment upon metal adsorption, while the evolution of Schottky barrier height at the initial growth stage is dominated by the adatom-induced gap states.     

Enhanced reactivity and selectivity in oxidation of Cu(1 0 0) and α-Cu-Al(5 at.%)(1 0 0) surfaces studied by electron and ion spectroscopies

In this study we investigate the influence of alloying on the reactivity and bonding of oxygen on α-Cu-Al(5 at.%)(1 0 0) oriented single crystal surfaces by X-ray photoelectron spectroscopy (XPS), ultra-violet spectroscopy (UPS) and low energy ion scattering (LEIS) spectroscopy, at room temperature. It was found that alloying results in an enhanced reactivity of both Cu and Al sites in comparison with the pure metals. According to adsorption curves calculated from XPS, saturation of the alloy surface occurs for exposures of ∼15 L. At saturation the total amount of adsorbed oxygen is similar for the alloy and pure copper surfaces. It was determined that first mostly Al sites are oxidized, followed by simultaneous oxidation of Cu and Al sites. At saturation the amount of oxygen bonded to Cu sites is ∼1.7 larger then that bonded to Al sites. From a comparison of the XPS and LEIS data analysis as a function of oxygen exposure it was found that oxidation of α-Cu-Al(5 at.%)(1 0 0) alloy is a multi-stage process with fast and slow stages. These stages involve an interplay of chemisorption, sub-surface diffusion of oxygen and Al segregation. UPS measurements show an increase in the work function of the alloy surface with oxygen adsorption. This is a contrast to pure Cu surfaces where the work function decreases at the initial stages of oxidation followed by an increase with oxygen exposure. Annealing to 400 °C drives the oxidized alloy surface into its thermodynamic state resulting in the formation of an aluminum oxide layer. Possible mechanisms to explain the enhanced reactivity of the alloy surface compared to that of pure copper are suggested and discussed.     

SiO adsorption on a p(2 × 2) reconstructed Si(1 0 0) surface

We have investigated the adsorption mechanism of SiO molecule incident on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. Stable adsorption geometries of SiO on Si surface, as well as their corresponding activation and adsorption energies are identified. We found that the SiO molecule is adsorbed on the Si(1 0 0) surface with almost no activation energy. An adsorption configuration where the SiO binds on the channel separating the dimer rows, forming a Si-O-Si bridge on the surface, is the energetically most favourable geometry found. A substantial red-shift in the calculated vibrational frequencies of the adsorbed SiO molecule in the bridging configurations is observed. Comparison of adsorption energies shows that SiO adsorption on a Si(1 0 0) surface is energetically less favourable than the comparable O₂ adsorption. However, the role of SiO in the growth of silicon sub-oxides during reactive magnetron plasma deposition is expected to be significant due to the relatively large amount of SiO molecules incident on the deposition surface and its considerable sticking probability. The stable adsorption geometries found here exhibit structural properties similar to the Si/SiO₂ interface and may be used for studying SiO_x growth.     

Oxygen adsorption on a Mo2C(0 0 0 1) surface: Angle-resolved photoemission study

Oxygen adsorption on a C-terminated α-Mo₂C(0 0 0 1) surface has been investigated with Auger electron spectroscopy, low-energy electron diffraction, and angle-resolved photoemission spectroscopy utilizing synchrotron radiation. It is found that the oxygen atoms adsorb on the Mo atoms in the second layer forming a (1 × 1) orthorhombic periodicity. The oxygen adsorption induces a peculiar state around the Fermi level, which is observed at 0.4 eV in the normal-emission spectra. ARPES measurements show that the state is a partially occupied metallic state. The photoionization cross section of the state shows a maximum at the photon energy of 56 eV, which is assigned as originating from the resonance of the Mo 4d photoemission involving Mo 4p → 4d photoexcitation.     

Oxygen adsorption and oxidation reactions on Au(2 1 1) surfaces: Exposures using O2 at high pressures and ozone (O3) in UHV

Nanosized gold particles supported on reducible metal oxides have been reported to show high catalytic activity toward CO oxidation at low temperature. This has generated great scientific and technological interest, and there have been many proposals to explain this unusual activity. One intriguing explanation that can be tested is that of Nørskov and coworkers [Catal. Lett. 64 (2000) 101] who suggested that the “unusually large catalytic activity of highly-dispersed Au particles may in part be due to high step densities on the small particles and/or strain effects due to the mismatch at the Au-support interface”. In particular, their calculations indicated that the Au(2 1 1) stepped surface would be much more reactive towards O₂ dissociative adsorption and CO adsorption than the Au(1 1 1) surface. We have now studied the adsorption of O₂ and O₃ (ozone) on an Au(2 1 1) stepped surface. We find that molecular oxygen (O₂) was not activated to dissociate and produce oxygen adatoms on the stepped Au(2 1 1) surface even under high-pressure (700 Torr) conditions with the sample at 300-450 K. Step sites do bind oxygen adatoms more tightly than do terrace sites, and this was probed by using temperature programmed desorption (TPD) of O₂ following ozone (O₃) exposures to produce oxygen adatoms up to a saturation coverage of θ_O = 0.90 ML. In the low-coverage regime (θ_O ? 0.15 ML), the O₂ TPD peak at 540 K, which does not shift with coverage, is attributed to oxygen adatoms that are bound at the steps on the Au(2 1 1) surface. At higher coverages, an additional lower temperature desorption peak that shifts from 515 to 530 K at saturation coverage is attributed to oxygen adsorbed on the (1 1 1) terrace sites of the Au(2 1 1) surface. Although the desorption kinetics are likely to be quite complex, a simple Redhead analysis gives an estimate of the desorption activation energy, E_d, for the step-adsorbed oxygen of 34 kcal/mol and that for oxygen at the terraces near saturation coverage of 33 kcal/mol, values that are similar to others reported on Au surfaces. Low Energy Electron Diffraction (LEED) indicates an oxygen-induced step doubling on the Au(2 1 1) surface at low-coverages (θ_O = 0.08-0.17 ML) and extensive disruption of the 2D ordering at the surface for saturation coverages of oxygen (θ_O ? 0.9 ML). Overall, our results indicate that unstrained step sites on Au(2 1 1) surfaces of dispersed Au nanoparticles do not account for the novel reactivity of supported Au catalysts for CO oxidation.     

A density functional study of atomic oxygen and water molecule adsorption on Ni(1 1 1) and chromium-substituted Ni(1 1 1) surfaces

Density functional theory (DFT) for generalized gradient approximation calculations has been used to study the adsorption of atomic oxygen and water molecules on Ni(1 1 1) and different kind of Ni-Cr(1 1 1) surfaces. The fcc hollow site is energetically the most favorable for atomic oxygen adsorption and on top site is favorable for water adsorption. The Ni-Cr surface has the highest absorption energy for oxygen at 6.86 eV, followed by the hcp site, whereas the absorption energy is 5.56 eV for the Ni surface. The Ni-O bond distance is 1.85 Å for the Ni surface. On the other hand, the result concerning the Ni-Cr surface implies that the bond distances are 1.93-1.95 Å and 1.75 Å for Ni-O and Cr-O, respectively. The surface adsorption energy for water on top site for two Cr atom substituted Ni-Cr surface is 0.85 eV. Oxygen atoms prefer to bond with Cr rather than Ni atoms. Atomic charge analysis demonstrates that charge transfer increases due to the addition of Cr. Moreover, a local density of states (LDOS) study examines the hybridization occurring between the metal d orbital and the oxygen p orbital; the bonding is mainly ionic, and water bonds weakly in both cases.     

First principle study of SrTiO3 (0 0 1) surface and adsorption of NO on SrTiO3 (0 0 1)

The results of first-principles calculations about the two possible terminations of (0 0 1) surface of SrTiO₃ perovskite and adsorption of NO on SrTiO₃ (0 0 1) surface were presented. Both surface parameters (atomic structures and electronic configurations) and adsorption parameters (bond, energy and charge) of NO on SrTiO₃ (0 0 1) surface, which have never been investigated before as far as we know were investigated using density functional theory calculations with the local-density approximation (DFT-LDA). It was found that the two possible terminations of SrTiO₃ (0 0 1) surface have large surface relaxation, which leads to surface polarization and exhibits different reactivity toward the dissociative adsorption of NO. The electronic states of TiO₂-terminated surface have larger difference than that of bulk, so it is more favorable for adsorption of NO than SrO-terminated surface.     

Adsorption and dissociation of ammonia on Au(1 1 1) surface: A density functional theory study

Periodic density functional theory (DFT) calculations using plane waves had been performed to systematically investigate the stable adsorption amine and its dehydrogenated reaction on Au(1 1 1) surface. The equilibrium configuration including on top, bridge, and hollow (fcc and hcp) sites had been determined by relaxation of the system. The adsorption both NH₃ on top site and NH₂ on bridge site is favorable on Au(1 1 1) surface, while the adsorption of NH on hollow (fcc) site is preferred. The adsorbates are adsorbed on the gold surface with the interaction between p orbital of adsorbate and the d orbital of gold atoms. The interaction between adsorbate and gold slab is more evident on the first layer than on any others. Furthermore, the dissociation reaction of NH₃ on clean gold surface, as well as on the pre-covered oxygen atom and pre-covered hydroxyl group surface had been investigated. The results show that the dehydrogenated reaction energy barrier on the pre-covered oxygen gold surface is lower. The adsorbed O can promote the dehydrogenation of amine. Additionally, OH as the product of the NH₃ dissociation reaction participates in continuous dehydrogenation reaction, and the reaction energy barrier is the lowest (22.77 kJ/mol). The results indicated that OH_ads play a key role in the dehydrogenated reaction on Au(1 1 1) surface.     

Vibrationally-assisted dissociative adsorption of oxygen on Ru(0 0 0 1)-p(2 × 1)-O

Supersonic molecular beam technique combined with high resolution X-ray photoelectron spectroscopy using synchrotron radiation was applied to the study of the dynamics of dissociative adsorption of oxygen on Ru(0 0 0 1) surface in high coverage region. The Ru(0 0 0 1) surface pre-covered with oxygen atoms of 0.5 monolayer, which corresponds to the p(2 × 1)-O structure, was dosed to oxygen molecules with translational energy of 0.5 eV. Oxygen uptake was compared between the cases with and without the beam source heated in order to verify the effects of internal energy of oxygen. We found drastic enhancement in initial sticking probability of oxygen when the beam source was heated to 1400 K. We concluded that the enhancement of sticking probability is mainly caused by molecular vibrational excitation, indicating that dissociation barrier is located in the exit channel on potential energy surface.