Quality variations of poultry litter biochar generated at different pyrolysis temperatures

Producing biochar and biofuels from poultry litter (PL) through slow pyrolysis is a farm-based, value-added approach to recycle the organic waste. Experiments were conducted to examine the effect of pyrolysis temperature on the quality PL biochar and to identify the optimal pyrolysis temperature for converting PL to agricultural-use biochar. As peak pyrolysis temperature increased incrementally from 300 to 600 °C, biochar yield, total N content, organic carbon (OC) content, and cation exchange capacity (CEC) decreased while pH, ash content, OC stability, and BET surface area increased. The generated biochars showed yields 45.7–60.1% of feed mass, OC 325–380 g kg⁻¹, pH 9.5–11.5, BET surface area 2.0–3.2 m² g⁻¹, and CEC 21.6–36.3 cmol_c kg⁻¹. The maximal transformation of feed OC into biochar recalcitrant OC occurred at 500 °C, yet 81.2% of the feed N was lost in volatiles at this temperature. To produce agricultural-use PL biochar, 300 °C should be selected in pyrolysis; for carbon sequestration and other environmental applications, 500 °C is recommended.     

Electrothermal vaporization coupled with inductively coupled plasma array–detector mass spectrometry for the multielement analysis of Al2O3 ceramic powders

An electrothermal vaporization (ETV) system useful for the analysis of solutions and slurries has been coupled with a sector-field inductively coupled plasma mass spectrometer (ICP–MS) equipped with an array detector. The ability of this instrument to record the transient signals produced for a number of analytes in ETV–ICP–MS is demonstrated. Detection limits for Mn, Fe, Co, Ni, Cu, Zn and Ga are in the range of 4–60 pg μL^− 1 for aqueous solutions and in the low μg g^− 1 range for the analysis of 10 mg mL^− 1 slurries of Al₂O₃ powders. The dynamic ranges measured for Fe, Cu and Ga spanned 3–5 orders of magnitude when the detector was operated in the low-gain mode and appear to be limited by the ETV system. Trace amounts of Fe, Cu and Ga could be directly determined in Al₂O₃ powders at the 2–270 μg g^− 1 level without the use of thermochemical reagents. The results well agree with literature values for Fe and Cu, whereas deviations of 50% at the 90 μg g^− 1 level for Ga were found.     

Determination of Cr(VI) in plants by electrothermal atomic absorption spectrometry after leaching with sodium carbonate

The determination of chromium (VI) compounds in plants by electrothermal atomic absorption spectrometry (ET AAS) is proposed based on their leaching with 0.1 M Na₂CO₃. Due to the presence of relatively high amounts of Na₂CO₃ in the resulting samples, the temperature and time of pyrolysis and atomization stages must be optimized to minimize the influence of the matrix. A limit of detection (LOD) for determination of Cr(VI) in plants by ET AAS was found to be 0.024 μg g⁻¹.The concentration of Cr(VI) and total chromium in plants collected in different geographical areas (South Africa and Russia), grown on soils high in chromium was determined. The concentration of Cr(VI) and total Cr in stems and leaves of plants was in the range of 0.04–0.7 μg g⁻¹ and 0.5–10 μg g⁻¹, respectively. The limited uptake of Cr(III) by plants, in comparison to its concentration in soil, can be explained by the very low solubility of natural Cr(III) compounds.Results for the determination of Cr(VI) were confirmed by the analysis of BCR CRM 545 (Cr(VI) in welding dust) with good agreement between certified (39.5 ± 1.3 μg mg⁻¹) and found (38.8 ± 1.2 μg mg⁻¹) values. The total concentration of Cr in plants has also been determined by ET AAS after dry ashing of samples at 650 °C. Results were confirmed by the analysis of BCR CRM 281 (Trace elements in Rye Grass) with good agreement between the found (2.12 ± 0.16 μg g⁻¹) and certified value (2.14 ± 0.12 μg g⁻¹).     

Electrochemical characterization of common catalysts and initiators for atom transfer radical polymerization in [BMIm][OTf]

The redox properties of some largely employed ATRP initiators and copper catalysts (Cu/L/X⁻) were investigated in 1-butyl-3-methylimidazolium trifluoromethanesulfonate (L = amine ligand, X = Br or Cl). Both Cu(II) and Cu(I) complexes are stable in the IL and, as required by ATRP, X⁻ stabilizes more Cu(II) than Cu(I). The activation rate constants of initiators by [Cu^ITPMA]⁺ were measured and a good correlation between k_act and the C-X bond dissociation free energy (BDFE) was observed. Overall, the results indicated that [BMIm][OTf] behaves much like organic solvents; the reported data launch the bases for a useful database to select the appropriate catalyst/initiator couple for ATRP in ILs.     

Thermodynamic and isotherm studies of the biosorption of Cu(II), Pb(II), and Zn(II) by leaves of saltbush (Atriplex canescens)

The Freundlich and Langmuir isotherms were used to describe the biosorption of Cu(II), Pb(II), and Zn(II) onto the saltbush leaves biomass at 297 K and pH 5.0. The correlation coefficients (R²) obtained from the Freundlich model were 0.9798, 0.9575, and 0.9963 for Cu, Pb, and Zn, respectively, while for the Langmuir model the R² values for the same metals were 0.0001, 0.1380, and 0.0088, respectively. This suggests that saltbush leaves biomass sorbed the three metals following the Freundlich model (R² > 0.9575). The K_F values obtained from the Freundlich model (175.5 · 10⁻², 10.5 · 10⁻², and 6.32 · 10⁻² mol · g⁻¹ for Pb, Zn, and Cu, respectively), suggest that the metal binding affinity was in the order Pb > Zn > Cu. The experimental values of the maximal adsorption capacities of saltbush leaves biomass were 0.13 · 10⁻², 0.05 · 10⁻², and 0.107 · 10⁻² mol · g⁻¹ for Pb, Zn, and Cu, respectively. The negative ΔG^∘ values for Pb and the positive values for Cu and Zn indicate that the Pb biosorption by saltbush biomass was a spontaneous process.     

Cu determination in crude oil distillation products by atomic absorption and inductively coupled plasma mass spectrometry after analyte transfer to aqueous solution

Cu was determined in a wide range of petroleum products from crude oil distillation using flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ETAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different procedures of sample preparation were evaluated: (i) mineralization with sulfuric acid in an open system, (ii) mineralization in a closed microwave system, (iii) combustion in hydrogen–oxygen flame in the Wickbold's apparatus, (iv) matrix evaporation followed by acid dissolution, and (v) acidic extraction. All the above procedures led to the transfer of the analyte into an aqueous solution for the analytical measurement step. It was found that application of FAAS was limited to the analysis of the heaviest petroleum products of high Cu content. In ICP-MS, the use of internal reference method (with Rh or In as internal reference element) was required to eliminate the matrix effects in the analysis of extracts and the concentrated solutions of mineralized heavy petroleum products. The detection limits (in original samples) were equal to, respectively, 10, 86, 3.3, 0.9 and 0.4 ng g^− 1 in procedures i–v with ETAAS detection and 10, 78, 1.1 and 0.5 ng g^− 1 in procedures i–iii and v with ICP-MS detection. The procedures recommended here were validated by recovery experiments, certified reference materials analysis and comparison of results, obtained for a given sample, in different ways. The Cu content in the analyzed samples was: 50–110 ng g^− 1 in crude oil, < 0.4–6 ng g^− 1 in gasoline, < 0.5–2 ng g^− 1 in atmospheric oil, < 6–100 ng g^− 1 in heavy vacuum oil and 140–300 ng g^− 1 in distillation residue.     

Production of char from vacuum pyrolysis of South-African sugar cane bagasse and its characterization as activated carbon and biochar

The potential of vacuum pyrolysis to convert sugar cane bagasse into char materials for wastewater treatment and soil amendment is the focus of this research paper. Vacuum pyrolysis produces both bio-oil and char in similar quantities. Vacuum pyrolysis has the potential to produce high quality chars for wastewater treatment and soil amendment directly during the conversion process, with no further upgrading required. In the present study, chars with the required porous structure was obtained directly from the vacuum pyrolysis process, making it very efficient as adsorbent both in terms of methylene blue (MB) adsorption with a N₂-BET surface area of 418 m² g⁻¹. Further steam activation of the chars benefited the development of meso- and macroporosity, although this upgrading step was not essential to achieve the required performance of char as an MB adsorbent. The development of large pores during the vacuum pyrolysis favored physisorption of MB, rather than chemisorption. The chemical nature of the vacuum pyrolysis char resulted in a slightly acidic surface (pH 6.56). The biochar from vacuum pyrolysis can be considered as a highly beneficial soil amendment, as it would enhance soil nutrient and water holding capacity, due to its high cation exchange capacity (122 cmol_c kg⁻¹) and high surface area. It is also a good source of beneficial plant macro- and micronutrients and contains negligible levels of toxic elements.     

1,2,4-Triazole as a reference material for combustion calorimetry of N-containing compounds

A micro-bomb combustion calorimeter recently designed for samples of mass  ≈ 80 mg has been improved and tested with m -methoxybenzoic acid in order to verify the chemistry of the combustion process and the accuracy of the energy corrections involved in the analysis of results. From measurements in this calorimeter, the standard massic energy of combustion of 1,2,4-triazole was determined to beΔ_cu^o =  − (19200.3  ±  3.4)J · g ^− 1. Some new measurements with our macro combustion calorimeter confirm an earlier result from this laboratory of  − (19203.1  ±  1.2)J · g ^− 1. Determination of the purity by d.s.c. of 1,2,4-triazole purified some 10 years ago reveals that samples of this compound remained unchanged and suggest that 1,2,4-triazole be used as a possible reference material for organic compounds with a high content of nitrogen. From the experimental results with the micro-bomb combustion calorimeter, the actual and earlier results from macro-bomb combustion calorimetry, and those obtained in other laboratories, the standard massic energy of combustion of 1,2,4-triazole was deduced to beΔ_cu^o =  − (19202.5  ±  1.7)J · g ^− 1.     

Electronic structure and Raman spectroscopy study of dibarium magnesium orthoborate,Ba2Mg(BO3)2

The samples of dibarium magnesium orthoborate Ba₂Mg(BO₃)₂ were synthesized by solid-state reaction. The X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Electronic structure and vibrational spectroscopy of Ba₂Mg(BO₃)₂ were systematically investigated by first principle calculation. A direct band gap of 4.4 eV was obtained from the calculated electronic structure results. The top valence band is constructed from O 2p states and the low conduction band mainly consists of Ba 5d states. Raman spectra for Ba₂Mg(BO₃)₂ polycrystalline were obtained at ambient temperature. The factor group analysis results show the total lattice modes are 5E_u + 4A_2u + 5E_g + 4A_1g + 1A_2g + 1A_1u, of which 5E_g + 4A_1g are Raman-active. Furthermore, we obtained the Raman active vibrational modes as well as their eigenfrequencies using first-principle calculation. With the assistance of the first-principle calculation and factor group analysis results, Raman bands of Ba₂Mg(BO₃)₂ were assigned as E_g (42 cm⁻¹), A_1g (85 cm⁻¹), E_g (156 cm⁻¹), E_g (237 cm⁻¹), A_1g (286 cm⁻¹), E_g (564 cm⁻¹), A_1g (761 cm⁻¹), A_1g (909 cm⁻¹), E_g (1165 cm⁻¹). The strongest band at 928 cm⁻¹ in the experimental spectrum is assigned to totally symmetric stretching mode of the BO₃ units.     

Application of vapour phase calibration method for determination of sorption of gases and VOC in polydimethylsiloxane membranes

Equilibrium sorption of oxygen, carbon dioxide, ethylene, dimethyl sulphide, trichloroethylene and toluene in polydimethylsiloxane (PDMS) at 30 °C is reported. Sorption isotherms of all compounds are well described by Henry’s law within the concentration intervals studied (0.008–257 g m⁻³). Vapour phase calibration (VPC), a static headspace method, was applied instead of the usual gravimetric and barometric sorption methods. Simple, rapid and reliable determination of air-PDMS partition coefficients (S) varying between 1 and 900 (g m⁻³/g m⁻³) was achieved by this method. Solubility of toluene in PDMS was the best of all tested compounds, followed by trichloroethylene, dimethyl sulphide, ethylene, carbon dioxide and oxygen. This observed sequence can be explained by the penetrant condensability, expressed by its critical temperature (T_c). Only for ethylene, a higher solubility is measured than expected from the correlation between S and T_c. This is caused by the relative high interaction of ethylene with the polymer. The Flory–Rehner interaction parameter, χ, for ethylene was calculated 0.004 while the χ values of the other compounds varied between 0.37 and 0.80. The solubility coefficients are shown to be independent on relative air humidity. For the compounds and concentration levels studied, the sorption of dimethyl sulphide is unaffected by the simultaneous sorption of other VOC. This non-competitive behaviour is consistent with the linear partition mechanism.     

Highly active PtRuFe/C catalyst for methanol electro-oxidation

High methanol electro-oxidation activity was obtained on novel PtRuFe/C (2:1:1 at.%) catalyst. Mass and specific activities were 5.67 A  g⁻¹ catal. and 177 mA m⁻² for the PtRuFe/C catalyst while those of the commercial PtRu/C catalyst were 2.28 A g⁻¹ catal. and 87.7 mA m⁻², respectively. CO stripping results showed that on-set voltage for CO electro-oxidation was lowered by incorporation of Fe. XRD and XPS results revealed that Fe₂O₃ was formed instead of Fe(0), which resulted in large electron deficiency in Pt and easy CO electro-oxidation. The electron deficiency of Pt was proved by XPS results of Pt4f peaks, which moved to higher binding energies in PtRuFe/C than PtRu/C.     

Highly mesoporous and high surface area carbon: A high capacitance electrode material for EDLCs with various electrolytes

Activated carbon fibers (ACFs) with high surface area and highly mesoporous structure for electrochemical double layer capacitors (EDLCs) have been prepared from polyacrylonitrile fibers by NaOH activation. Their unique microstructural features enable the ACFs to present outstanding high specific capacitance in aqueous, non-aqueous and novel ionic liquid electrolytes, i.e. 371 F g⁻¹ in 6 mol L⁻¹ KOH, 213 F g⁻¹ in 1 mol L⁻¹ LiClO₄/PC and 188 F g⁻¹ in ionic liquid composed of lithium bis(trifluoromethane sulfonyl)imide (LiN(SO₂CF₃)₂, LiTFSI) and 2-oxazolidinone (C₃H₅NO₂, OZO), suggesting that the ACF is a promising electrode material for high performance EDLCs.     

The standard molar enthalpy of sublimation ofη5-bis-pentamethylcyclopentadienyl iron measured with an electrically calibrated vacuum-drop sublimation microcalorimetric apparatus

A heat-flow Calvet microcalorimeter was adapted for the measurement of sublimation enthalpies by the vacuum-drop method, with samples of masses in the range 1 mg to 5 mg. The electrically calibrated apparatus was tested by determining the enthalpies of sublimation of benzoic acid and ferrocene, at T =  298.15 K. The obtained results, Δ_cr^gH_m^o(C₇H₆O₂)  =  (88.3  ±  0.5)kJ · mol ^− 1and Δ_cr^gH_m^o(C₁₀H₁₀Fe) =  (73.3  ±  0.1)kJ · mol ^− 1, are in excellent agreement with the corresponding values recommended in the literature. Subsequent application of the apparatus to the determination of the enthalpy of sublimation of η⁵-bis-pentamethylcyclopentadyenyl iron, at T =  298.15 K, led to Δ_cr^gH_m^o(C₂₀H₃₀Fe)  =  (96.8  ±  0.6)kJ · mol ^− 1.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.     

Highly selective thiocyanate electrode based on bis-bebzoin-semitriethylenetetraamine binuclear copper(II) complex as neutral carrier

A novel selective thiocyanate PVC membrane electrode based on bis-bebzoin-semitriethylenetetraamine binuclear copper(II) [Cu(II)₂–BBSTA] as neutral carrier is reported, which displays an anti-Hofmeister selectivity sequence in following order: SCN⁻ > ClO₄⁻ > I⁻ >Sal⁻ >SO₃²⁻ >NO₃⁻ > H₂PO₄⁻ > Cl⁻ >NO₂⁻ > SO₄²⁻. The electrode exhibits Nernstian potential linear range to thiocyanate from 1.0 × 10⁻¹ to 9.0 × 10⁻⁷ mol/l with a detection limit 7.0 × 10⁻⁷ mol/l and a slope of −57.0 mV/decade in pH 5.0 of phosphorate buffer solution at 25 °C. The response mechanism is discussed in view of the AC impedance technique and the UV spectroscopy technique. From comparison of potentiometric response characteristics between the binuclear metallic complex copper(II) [Cu(II)₂–BBSTA] and mononuclear copper(II) metallic complex [Cu(II)–BBSDA], an enhanced response towards thiocyanate from the electrode based on binuclear metallic complex copper (II) [Cu(II)₂–BBSTA] was observed. The electrode based on binuclear copper(II) compound was used to determine the thiocyanate content in waste water with satisfactory results.     

Heat capacities,third-law entropies and thermodynamic functions of the geometrically frustrated antiferromagnetic spinels GeCo2O4 and GeNi2O4 from T=(0 to 400) K

The molar heat capacities of GeCo₂O₄ and GeNi₂O₄, two geometrically frustrated spinels, have been measured in the temperature range from T=(0.5 to 400) K. Anomalies associated with magnetic ordering occur in the heat capacities of both compounds. The transition in GeCo₂O₄ occurs at T=20.6 K while two peaks are found in the heat capacity of GeNi₂O₄, both within the narrow temperature range between 11.4<(T/K)<12.2. Thermodynamic functions have been generated from smoothed fits of the experimental results. At T=298.15 K the standard molar heat capacities are (143.44 ± 0.14) J · K⁻¹ · mol⁻¹ for GeCo₂O₄ and (130.76 ± 0.13) J · K⁻¹ · mol⁻¹ for GeNi₂O₄. The standard molar entropies at T=298.15 K for GeCo₂O₄ and GeNi₂O₄ are (149.20 ± 0.60) J · K⁻¹ · mol⁻¹ and (131.80 ± 0.53) J · K⁻¹ · mol⁻¹ respectively. Above 100 K, the heat capacity of the cobalt compound is significantly higher than that of the nickel compound. The excess heat capacity can be reasonably modeled by the assumption of a Schottky contribution arising from the thermal excitation of electronic states associated with the CO²⁺ ion in a cubic crystal field. The splittings obtained, 230 cm⁻¹ for the four-fold-degenerate first excited state and 610 cm⁻¹ for the six-fold degenerate second excited state, are significantly lower than those observed in pure CoO.     

Flame atomic absorption spectrometry determination of trace amount of gold after separation and preconcentration onto ion-exchange polyethylenimine coated on Al2O3

The object of this work is to develop a simple and selective method for efficient extraction of Au(III) ions in aqueous solution using a new solid-phase extraction sorbent. Polyethylenimine (PEI) ion-exchange polymer was coated on alumina in the presence of NaNO₃. The method is based on sorption of Au³⁺ ions on 50 mg PEI/Al₂O₃. A solution of 0.5 M thiourea, then 1.0 M HCl effectively eluted the gold ion and then aspirated into flame atomic absorption spectroscopy (FAAS). The influence of flow rate of sample solution and eluent, the pH effect, eluent type and sorption capacity was investigated. The effects of various diverse ions for preconcentration and separation of the gold ion were investigated. Relative standard deviation of 4.0 μg mL⁻¹ of gold was 1.46% (n = 10). The detection limit was 26.2 ng L⁻¹ in original solution. The method has been applied successfully for the recovery of trace amount of Au(III) ions from water samples.     

VO2 nano-sheet negative electrodes for lithium-ion batteries

Vanadium dioxide (VO₂) nano-sheets were directly synthesized via a continuous hydrothermal process and were investigated as electrodes in a wide potential range of 0.05–3 V vs. Li/Li⁺. The nano-sheets showed excellent capacity retention, with a specific capacity of 350 mAh g^− 1 at an applied current of 0.1 A g^− 1 and 95 mAh g^− 1 at 10 A g^− 1. Further electrochemical testing suggested that a significant proportion of the charge storage in the cells was due to pseudocapacitive processes.     

Diffusion of ferrocene methanol in super-cooled aqueous solutions using cylindrical microelectrodes

The diffusion of ferrocene methanol in super-cooled aqueous solutions containing sucrose has been studied, using disk and cylindrical microelectrodes, over a wide viscosity range. The solution viscosity and the reduced temperature T/T_g (T_g being the glass transition temperature) were varied by changing the sucrose concentration and the temperature of the system. The voltammetric limiting current obtained with a disk microelectrode and the i(t) response on a cylindrical microelectrode after a potential step were used to determine diffusion coefficients from 7 × 10⁻⁶ cm² s⁻¹ down to 2 × 10⁻¹¹ cm² s⁻¹. The electrochemical procedure described in this work allows a simple and accurate measurement of the dynamics of electroactive solutes in glass-forming liquids.     

Outstanding room-temperature capacitance of biomass-derived microporous carbons in ionic liquid electrolyte

A remarkable capacitance of 180 F·g^− 1 (at 5 mV·s^− 1) in solvent-free room-temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, was achieved in symmetric supercapacitors using microporous carbons with a specific surface area of ca. 2000 m²·g^− 1 calculated from gas sorption by the 2D-NLDFT method. The efficient capacitive charge storage was ascribed to textural properties: unlike most activated carbons, high specific surface area was made accessible to the bulky ions of the ionic liquid electrolyte thanks to micropores (1–2 nm) enabled by fine-tuning chemical activation. From the industrial perspective, a high volumetric capacitance of ca. 80 F·cm^− 3 was reached in neat ionic liquid due to the absence of mesopores. The use of microporous carbons from biomass waste represents an important advantage for large-scale production of high energy density supercapacitors.