Determination of cerium ion by polymeric membrane and coated graphite electrode based on novel pendant armed macrocycle

Plasticized membranes using 2,3,4:12,13,14-dipyridine-1,3,5,8,11,13,15,18-octaazacycloicosa-2,12-diene (L₁) and 2,3,4:12,13,14-dipyridine-1,5,8,11,15,18-hexamethylacrylate-1,3,5,8,11,13,15,18-octaazacycloicosa-2,12-diene (L₂) have been prepared and explored as Ce(III) selective sensors. Effect of various plasticizers viz. dibutylphthalate (DBP), tri-n-butylphthalate (TBP), o-nitrophenyloctylether (o-NPOE), dioctylphthalate (DOP), benzylacetate (BA) and anion excluders, sodium tetraphenylborate (NaTPB) and potassium tetrakis p-(chlorophenyl) borate was studied in detail and improved performance was observed. Optimum performance was observed for the membrane sensor having a composition of L₂:PVC:o-NPOE:KTpClPB in the ratio of 6:34:58:2 (w/w, mg). The performance of the membrane based on L₂ was compared with polymeric membrane electrode (PME) as well as with coated graphite electrode (CGE). The electrodes exhibit Nernstian slope for Ce(III) ions with limits of detection of 8.3 × 10⁻⁸ mol L⁻¹ for PME and 7.7 × 10⁻⁹ mol L⁻¹ for CGE. The response time for PME and CGE was found to be 12 s and 10 s respectively. The potentiometric responses are independent of the pH of the test solution in the pH range 3.5-7.5 for PME and 2.5-8.5 for CGE. The CGE could be used for a period of 5 months. The practical utility of the CGE has been demonstrated by its usage as an indicator electrode in potentiometric titration of oxalate and fluoride ions with Ce(III) solution. The proposed electrode was also successfully applied to the determination of fluoride ions in mouthwash solution and oxalate ions in real samples.     

Flow injection analysis of ethyl xanthate by in-line dialysis and UV spectrophotometric detection

A simple and sensitive spectrophotometric flow method for determination of low concentrations of the flotation collector O-ethyldithiocarbonate (ethyl xanthate, CH₃CH₂-O-CS₂⁻) in solutions is described. The method is based on ethyl xanthate detection at 301 nm in medium of NaOH 50 mmol L⁻¹. By injection of 200 μL of sample, the analytical method shows linear response for the ethyl xanthate concentration from 0.5 up to 500 μmol L⁻¹. Successive injections of 4 μmol L⁻¹ ethyl xanthate (n = 23) show a coefficient of variation lower than 0.6%, denoting high repeatability. The detection limit is 0.3 μmol L⁻¹. At a flow rate of 2.0 mL min⁻¹, a frequency of 120 injections/h of ethyl xanthate can be attained. By introduction of a tangential dialysis cell in the FIA system, the manual sample filtration step with 0.22 μm filter was eliminated and the residual interference of suspended material, was completely overcome even for unfiltered sludge suspension samples, an important advantage that compensates for the frequency reduction to 25 injections/h elevation and detection limit elevation to 2 μmol L⁻¹, still outreaching for many applications. Potential applications of the method embrace the at line determination of ethyl xanthate in the ore processing industry, control of the concentration at its optimal level during the flotation process, as well as monitoring of residues in the effluents.     

Ultrasensitive fluorometric determination of hydrogen peroxide and glucose by using multiferroic BiFeO3 nanoparticles as a catalyst

BiFeO₃ magnetic nanoparticles (BFO MNPs) are used as a catalyst to develop an ultrasensitive method for the determination of H₂O₂. It is found that BFO MNPs can catalyze the decomposition of H₂O₂ to produce OH radicals, which in turn oxidize the weakly fluorescent benzoic acid to a strongly fluorescent hydroxylated product with a maximum emission at 405 nm. This makes it possible to sensitively quantify traces of H₂O₂. Under optimized conditions, the fluorescence intensity is observed to be well linearly correlated with H₂O₂ concentration from 2.0 × 10⁻⁸ to 2.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 4.5 × 10⁻⁹ mol L⁻¹ (S/N = 3). In addition, a selective method for glucose determination is developed by using both glucose oxidase and BFO MNPs, which has a linear range for glucose concentration from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. These new methods have been successfully applied for the determination of H₂O₂ in rainwater and glucose in human serum samples.     

A ratiometric fluorescent probe for fluoride ion employing the excited-state intramolecular proton transfer

A ratiometric fluorescent probe 1 for fluoride ion was developed based on modulation of the excited-state intramolecular proton transfer (ESIPT) process of 2-(2′-hydroxyphenyl)benzimidazole (HPBI) through the hydroxyl group protection/deprotection reaction. The probe 1 was readily prepared by the reaction of HPBI with tert-butyldimethylsilyl chloride (TBS-Cl) and shows only fluorescence emission maximum at 360 nm. Upon treatment with fluoride in aqueous DMF solution, the TBS protective group of probe 1 was removed readily and ESIPT of the probe was switched on, which resulted in a decrease of the emission band at 360 nm and an increase of a new fluorescence peak around 454 nm. The fluorescent intensity ratio at 454 and 360 nm (I₄₅₄/I₃₆₀) increases linearly with fluoride ion concentration in the range 0.3-8.0 μmol L⁻¹ and the detection limit is 0.19 μmol L⁻¹. The proposed probe shows excellent selectivity toward fluoride ion over other common anions. The method has been successfully applied to the fluoride determination in toothpaste and tap water samples.     

Electrochemiluminescent behaviors of alkaloids and tris(2,2'-bipyridine) ruthenium in organically modified silicate film

Electrogenerated chemiluminescences (ECLs) of alkaloids, such as berberine, trigonelline, allantoin and betaine, were studied in an aqueous alkaline buffer solution (pH 9.5), based on tris(2,2′-bipyridine)ruthenium(II) [Ru(bpy)₃²⁺] immobilized in organically modified silicates (ORMOSILs) film on a glassy carbon electrode (GCE). The immobilized Ru(bpy)₃²⁺ showed good electrochemical and photochemical activities. In a flow system, the eluted alkaloids were oxidized on the modified GCE, and reacted with immobilized Ru(bpy)₃²⁺ at the potential of +1.50 V (versus Ag/AgCl). The luminescence with λ_max 610 nm was caused by a reaction of electrolytically formed Ru(bpy)₃³⁺ with an oxidized amine group to generate Ru(bpy)₃^2+*. The determination limit was 5 × 10⁻⁶ mol L⁻¹, 8 × 10⁻⁶ mol L⁻¹, 2.0 × 10⁻⁵ mol L⁻¹ and 5.0 × 10⁻⁵ mol L⁻¹ for berberine, trigonelline, allantoin and betaine at S/N 3, respectively. In addition, the factors affecting the determination of the four alkaloids were also studied.     

A portable and low cost equipment for flow injection chemiluminescence measurements

A compact, reliable and low cost flow injection chemiluminescence system is described. The flow system consists of a set of solenoid micro-pumps that can dispense reproductive micro-volumes of solutions. The luminometer was based on a coiled cell constructed from polyethylene tubing that was sandwiched between two large area photodiodes. The whole equipment costs about US$ 750 and weights ca. 3 kg. Equipment performance was evaluated by measuring low concentrations of hydrogen peroxide by oxidation of luminol and for the determination of ammonium, based on its inhibition of the luminescence provided by the reaction of luminol and sodium hypochlorite. Linear responses were achieved within 1.0-80 μmol L⁻¹ H₂O₂ and 0.6-60 μmol L⁻¹ NH₄⁺ with detection limits estimated as 400 nmol L⁻¹ H₂O₂ and 60 nmol L⁻¹ NH₄⁺ at the 99.7% confidence level. Coefficients of variation were 1.0 and 1.8%, estimated for 20 μmol L⁻¹ H₂O₂ and 15 μmol L⁻¹ NH₄⁺ (n = 20), respectively. Reagent consumption of 55 μg luminol, effluent volume of 950 μL per determination and sampling rate of 120 samples per hour were also achieved.     

Improvement of microwave-assisted digestion of milk powder with diluted nitric acid using oxygen as auxiliary reagent

The feasibility of using diluted HNO₃ solutions under oxygen pressure for decomposition of whole and non-fat milk powders and whey powder samples has been evaluated. Digestion efficiency was evaluated by determining the carbon content in solution (digests) and the determination of Ca, Cd, Cu, Fe, K, Mg, Mn, Mo, Na, Pb and Zn was performed by inductively coupled plasma optical emission spectrometry and Hg by chemical vapor generation coupled to inductively coupled plasma mass spectrometry. Samples (up to 500 mg) were digested using HNO₃ solutions (1 to 14 mol L^− 1) and the effect of oxygen pressure was evaluated between 2.5 and 20 bar. It was possible to perform the digestion of 500 mg of milk powder using 2 mol L^− 1 HNO₃ with oxygen pressure ranging from 7.5 to 20 bar with resultant carbon content in digests lower than 1700 mg L^− 1. Using optimized conditions, less than 0.86 mL of concentrated nitric acid (14 mol L^− 1) was enough to digest 500 mg of sample. The accuracy was evaluated by determination of metal concentrations in certified reference materials, which presented an agreement better than 95% (Student's t test, P < 0.05) for all the analytes.     

Application of Fenton reaction for nanomolar determination of hydrogen peroxide in seawater

A simple and sensitive method for the determination of nanomolar levels of hydrogen peroxide (H₂O₂) in seawater has been developed and validated. This method is based on the reduction of H₂O₂ by ferrous iron in acid solution to yield hydroxyl radical (OH) which reacts with benzene to produce phenol. Phenol is separated from the reaction mixture by reversed phase high performance liquid chromatography and its fluorescence intensity signals were measured at excitation and emission of 270 and 298 nm, respectively. Under optimum conditions, the calibration curve exhibited linearity in the range of (0-50) × 10³ nmol L⁻¹ H₂O₂. The relative standard deviations for five replicate measurements of 500 and 50 nmol L⁻¹ H₂O₂ are 1.9 and 2.4%, respectively. The detection limit for H₂O₂, defined as three times the standard deviation of the lowest standard solution (5 nmol L⁻¹ H₂O₂) in seawater is 4 nmol L⁻¹. Interference of nitrite ion (NO₂⁻) on the fluorescence intensity of phenol was also investigated. The result indicated that the addition of 10 μmol L⁻¹ NO₂⁻ to seawater samples showed no significant interference, although, the addition of 50 μmol L⁻¹ NO₂⁻ to the seawater samples decreases the fluorescence intensity signals of phenol by almost 40%. Intercomparison of this method with well-accepted (p-hydroxyphenyl) acetic acid (POHPAA)-FIA method shows excellent agreement. The proposed method has been applied on-board analysis of H₂O₂ in Seto Inland seawater samples.     

Construction of a novel molecularly imprinted sensor for the determination of O,O-dimethyl-(2,4-dichlorophenoxyacetoxyl)(3′-nitrophenyl)methinephosphonate

A novel voltammetric sensor for O,O-dimethyl-(2,4-dichlorophenoxyacetoxyl)(3′-nitrophenyl)methinephosphonate (Phi-NO₂) based on molecularly imprinted polymer (MIP) film electrode is constructed by using sol-gel technology. The sensor responds linearly to Phi-NO₂ over the concentration range of 2.0 × 10⁻⁵ to 1.0 × 10⁻⁸ mol L⁻¹ and the detection limit is 1.0 × 10⁻⁹ mol L⁻¹ (S/N = 3). This sensor provides an efficient way for eliminating interferences from coexisting substances in the solution. The high sensitivity, selectivity and stability of the sensor demonstrates its practical application for a simple and rapid determination of Phi-NO₂ in cabbage samples.     

Biomimetic sensor based on MnMn complex as manganese peroxidase mimetic for determination of rutin

A novel biomimetic sensor for rutin determination based on a dinuclear complex [Mn^IIIMn^II(Ldtb)(μ-OAc)₂]BPh₄ containing an unsymmetrical dinucleating ligand, 2-[N,N-bis(2-pyridylmethyl)-aminomethyl]-6-[N-(3,5-di-tert-butyl-2-oxidoben-zyl)-N-(2-pyridylamino)aminomethyl]-4-methylphenol (H₂Ldtb), as a manganese peroxidase mimetic was developed. Several parameters were investigated to evaluate the performance of the biomimetic sensor obtained after the incorporation of the dinuclear complex in a carbon paste. The best performance was obtained in 75:15:10% (w/w/w) of the graphite powder:Nujol:Mn^IIIMn^II complex, 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0) and 4.0 × 10⁻⁵ mol L⁻¹ hydrogen peroxide. The response of the sensor towards rutin concentration was linear using square wave voltammetry in the range of 9.99 × 10⁻⁷ to 6.54 × 10⁻⁵ mol L⁻¹ (r = 0.9998) with a detection limit of 1.75 × 10⁻⁷ mol L⁻¹. The recovery study performed with pharmaceuticals ranged from 96.6% to 103.2% and the relative standard deviation was 1.85% for a solution containing 1.0 × 10⁻³ mol L⁻¹ rutin (n = 6). The lifetime of this biomimetic sensor was 200 days (at least 750 determinations). The results obtained for rutin in pharmaceuticals using the biomimetic sensor and those obtained with the official method are in agreement at the 95% confidence level.     

Electrogenerated chemiluminescence from thiol-capped CdTe quantum dots and its sensing application in aqueous solution

In this paper, the electrogenerated chemiluminescence (ECL) from thiol-capped CdTe quantum dots (QDs) was reported. The ECL emission was occurred at −1.1 V and reached a maximum value at −2.4 V when the potential was cycled between 0.0 and −2.5 V. The reduced species of CdTe QDs could react with the coreactants to produce the ECL emission. The CdTe QD concentration (6.64 × 10⁻⁷ mol L⁻¹) of ECL is lower than that (1.0 × 10⁻³ mol L⁻¹) of chemiluminescence (CL). Based on the enhancement of light emission from thiol-capped CdTe QDs by H₂O₂ in the negative electrode potential, a novel method for the determination of H₂O₂ was developed. The light intensity was linearly proportional to the concentration of H₂O₂ between 2.0 × 10⁻⁷ and 1.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 6.0 × 10⁻⁸ mol L⁻¹. Compared with most of previous reports, the proposed method has higher sensitivity for the determination of H₂O₂. In addition, the ECL spectrum of thiol-capped CdTe QDs exhibited a peak at around 620 nm, which was substantially red shifted from the photoluminescence (PL) spectrum, suggesting the surface states play an important role in this ECL process.     

The petentiometric determination of peroxide hydrogen and glucose on the glassy electrode modified by the calix[4]arene

A new petentiometric method to determine peroxide hydrogen and glucose had been studied. This method had been applied on the petentiometric determination of peroxide hydrogen and glucose in the total ionic strength adjustment buffer (TISAB) (pH 7.5) solution with the glassy electrode modified by the calix[4]arene. The glassy carbon electrode covered with the calix[4]arene depended on the H₂O₂ concentration in the range of log[H₂O₂] from −3.3 to −1.2 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 65.6 ± 3 mV and the detection limit of peroxide hydrogen was 4.0 × 10⁻⁵ mol L⁻¹. The glassy carbon electrode covered with the calix[4]arene depended on the glucose concentration in the range of log[glucose] from −3.6 to −2.8 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 50.2 ± 2 mV and the detection limit of glucose was 2.0 × 10⁻⁵ mol L⁻¹. The electrode had the good selectivity, sensitivity, stability and repeatability.     

Microflow injection chemiluminescence system with spiral microchannel for the determination of cisplatin in human serum

A new microflow injection chemiluminescence (μFI-CL) system was described for the determination of cisplatin in human serum. By using the microchip with double spiral channel configuration, the sensitivity was greatly enhanced due to more efficient mixing of the analyte and reagent solutions. Experimental results revealed that common ions in human serum, such as Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Ni²⁺, Na⁺, K⁺, Ca²⁺, Cl⁻, NO₃⁻, Ac⁻, CO₃²⁻, PO₄³⁻, SO₄²⁻ did not cause interference with the detection of Pt(II) by using 1,10-phenanthroline as the masking agent. Under the optimized conditions, a linear calibration curve (R² = 0.998) over the range 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ was obtained with the detection limit of 1.24 × 10⁻⁹ mol L⁻¹. The relative standard deviation was found to be 3.46% (n = 12) for 2.0 × 10⁻⁷ mol L⁻¹. The sample consumption was only 2 μL with the sample throughput of 72 h⁻¹. It had been used for trace platinum determination in cisplatin injection and human serum samples after the dosage of cisplatin. The recovery varied from 97.6 to 103.9%. The results proved that the proposed μFI-CL system had the advantages of high sensitivity and precision, low sample and reagents consumption, and high analytical throughput.     

Determination of uranium by adsorptive stripping voltammetry at a lead film electrode

An adsorptive stripping voltammetric procedure for the determination of U(VI) at an in situ plated lead film electrode is described. The U(VI) complex with cupferron was accumulated from an acetate buffer solution of pH 4.2 at the potential −0.65 V. The measurements were carried out from undeaerated solutions. The calibration graph for an accumulation time of 180 s was linear from 5 × 10⁻¹⁰ to 2 × 10⁻⁸ mol L⁻¹. The detection limit was 2 × 10⁻¹⁰ mol L⁻¹, the relative standard deviation for 2 × 10⁻⁸ mol L⁻¹ U(VI) was 4.3%. The proposed procedure was validated in the course of U(VI) determination in water certified reference materials.     

Electroanalytical determination of estriol hormone using a boron-doped diamond electrode

A boron-doped diamond (BDD) electrode was used for the electroanalytical determination of estriol hormone in a pharmaceutical product and a urine sample taken during pregnancy by square-wave voltammetry. The optimized experimental conditions were: (1) a supporting electrolyte solution of NaOH at a pH of 12.0, and (2) a frequency of 20 Hz, a pulse height of 30 mV and a scan increment of 2 mV (for the square-wave parameters). The analytical curve was linear in the concentration range of 2.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹ (r = 0.9994), with a detection limit of 1.7 × 10⁻⁷ mol L⁻¹ and quantification limit of 8.5 × 10⁻⁷ mol L⁻¹. Recoveries of estriol were in the range of 98.6-101.0%, for the pharmaceutical sample, and 100.2-103.4% for the urine sample, indicating no significant matrix interference effects on the analytical results. The accuracy of the electroanalytical methodology proposed was compared to that of the radioimmunoassay method. The values for the relative error between the proposed and standard methods were −7.29% for the determination of estriol in the commercial product and −4.98% in a urine sample taken during pregnancy. The results obtained suggest a reliable and interesting alternative method for electroanalytical determination of estriol in pharmaceutical products and urine samples taken during pregnancy using a boron-doped diamond electrode.     

Determination of brominated phenols in water samples by on-line coupled isotachophoresis with capillary zone electrophoresis

A method for determination of nine brominated phenols as environmental risk compounds was developed by on-line coupled capillary isotachophoresis and capillary zone electrophoresis (ITP–CZE). For ITP step, 1 × 10⁻² mol L⁻¹ hydrochloric acid with 3 × 10⁻² mol L⁻¹ ammediol pH 9.1 was used as the leading electrolyte, and 3 × 10⁻² mol L⁻¹ β-alanine with 2 × 10⁻² mol L⁻¹ sodium hydroxide pH 10.05 was used as the terminating electrolyte. As the background electrolyte for CZE separation, 2.5 × 10⁻² mol L⁻¹ β-alanine with 2.5 × 10⁻² mol L⁻¹ lysine pH 9.6 was used. All electrolytes contained 0.05% or 0.1% (m/v) hydroxyethylcellulose to suppress the electroosmotic flow. UV detection at wavelength 220 nm was used. Detection limits in order of tens of nmol L⁻¹ were achieved. Good repeatability of migration times (less than 0.33% RSD) and good repeatability of peak areas (less than 7.19% RSD) at concentration level 5 × 10⁻⁸ mol L⁻¹ were observed. Developed ITP–CZE method was applied to determination of brominated phenols in spiked tap and river water samples.     

Biosensor for chlorogenic acid based on an ionic liquid containing iridium nanoparticles and polyphenol oxidase

A biosensor based on the ionic liquid, 1-n-butyl-3-methylimidazolium hexafluorophosphate containing dispersed iridium nanoparticles (Ir-BMI.PF₆) and polyphenol oxidase was constructed. This enzyme was obtained from the sugar apple (Annona squamosa), immobilized in chitosan ionically crosslinked with oxalate. The biosensor was used for determination of chlorogenic acid by square wave voltammetry. The polyphenol oxidase catalyzes the oxidation of chlorogenic acid to the corresponding o-quinone, which is electrochemically reduced back to this substance at +0.25 V vs. Ag/AgCl. Under optimized operational conditions the chlorogenic acid concentration was linear in the range of 3.48 × 10⁻⁶ to 4.95 × 10⁻⁵ mol L⁻¹ with a detection limit of 9.15 × 10⁻⁷ mol L⁻¹. The biosensor was applied in the determination of chlorogenic acid in organic and decaffeinated coffee and the results compared with those obtained using the capillary electrophoresis method. The recovery study for chlorogenic acid in these samples gave values of 93.2-105.7%.     

A dispersive liquid-liquid microextraction procedure for determination of boron in water after ultrasound-assisted conversion to tetrafluoroborate

A novel, simple and green procedure is presented for the determination of boron. The method is based on ultrasound-assisted conversion of boron to tetrafluoroborate anion and the formation of an ion pair between BF₄⁻ and Astra Phloxine reagent (R), followed by dispersive liquid-liquid microextraction of the ion pair formed and subsequent UV-vis spectrophotometric detection. The conversion of boron to tetrafluoroborate anion is performed in an acidic medium of 0.9 mol L⁻¹ H₂SO₄ in the presence of 0.1 mol L⁻¹ F^- by means of 10 min of ultrasonication. The extraction of the ion pair formed between BF₄⁻ and R (1 × 10⁻⁴ mol L⁻¹ R) is carried out by dispersive liquid-liquid microextraction using 0.5 mL of amyl acetate (as extraction solvent), tetrachloromethane (as auxiliary solvent) and acetonitrile (as dispersive solvent) in a ratio of 1:1:2. The absorbance of the coloured extracts obeys Beer's law in the range 0.22-18.7 mg L⁻¹ of B(III) at 553 nm wavelength. The limit of detection calculated from a blank test (n = 10) based on 3 s is 0.015 mg L⁻¹ of B(III). The method was applied to the determination of boron in mineral waters.     

Catalytic-adsorptive stripping voltammetric determination of ultra-trace iridium(III). Application to fresh- and sea-water

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3 mol L⁻¹ acetate buffer pH 4.7 + 6.9 × 10⁻² mol L⁻¹ NaBrO₃ + 2.7 × 10⁻⁵ mol L⁻¹ cetyltrimethylammonium bromide (CTAB) + 0.2 mol L⁻¹ KCl was employed as the supporting electrolyte.The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d.The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviation s_r%, was generally lower than 5%. The limit of detection was of the order of 2-3 ng L⁻¹.Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area.     

Simple and fast spectrophotometric determination of H(2)O(2) in photo-Fenton reactions using metavanadate

This work proposes a spectrophotometric method for the determination of hydrogen peroxide during photodegradation reactions. The method is based on the reaction of H₂O₂ with amonium metavanadate in acidic medium, which results in the formation of a red-orange color peroxovanadium cation, with maximum absorbance at 450 nm. The method was optimized using the multivariate analysis providing the minimum concentration of vanadate (6.2 mmol L⁻¹) for the maximum absorbance signal. Under these conditions, the detection limit is 143 μmol L⁻¹. The reaction product showed to be very stable for samples of peroxide concentrations up to 3 mmol L⁻¹ at room temperature during 180 h. For higher concentrations however, samples must be kept refrigerated (4 °C) or diluted. The method showed no interference of Cl⁻ (0.2-1.3 mmol L⁻¹), NO₃⁻ (0.3-1.0 mmol L⁻¹), Fe³⁺ (0.2-1.2 mmol L⁻¹) and 2,4-dichlorophenol (DCP) (0.2-1.0 mmol L⁻¹). When compared to iodometric titration, the vanadate method showed a good agreament. The method was applied for the evaluation of peroxide consumption during photo-Fenton degradation of 2,4-dichlorophenol using blacklight irradiation.