Determination of Ga, Ge, As, Se and Sb in fly ash samples by ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Ga, Ge, As, Se and Sb in fly ash samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd and ascorbic acid were used as the mixed modifiers to enhance the ion signals. This method has been applied to determine Ga, Ge, As, Se and Sb in NIST SRM 1633a and 1633b coal fly ash reference materials and a fly ash sample collected locally. Since the sensitivities of the elements studied in slurry solution and aqueous solution were different slightly, analyte addition technique was used for the determination of Ga, Ge, As, Se and Sb in these samples. The As and Se analysis results of the reference materials agreed with the certified values. The results for which no certified value was available were also found to be in good agreement between the ETV-ICP-MS results and the reference values. The reference value was obtained by digesting the samples and analyzing the digested sample solutions by pneumatic nebulization Dynamic Reaction Cell™ (DRC) ICP-MS. The method detection limits estimated from analyte addition curves were about 0.23, 0.13, 0.17, 0.25 and 0.11 μg g⁻¹ for Ga, Ge, As, Se and Sb, respectively, in original fly ash samples.     

Electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry for the determination of Fe,Co, Ni,Cu, and Zn in biological samples

Slurry sampling electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry (ETV-DRC-ICP-MS) has been applied to determine Fe, Co, Ni, Cu, and Zn in biological samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd was used as the modifier. The effectiveness of the ETV sample introduction technique and dynamic reaction cell in alleviating various spectral interferences in ICP-MS analysis has been demonstrated. This method has been applied to determine Fe, Co, Ni, Cu, and Zn in NIST SRM 1573a tomato leaves reference material and NRCC DORM-2 dogfish muscle reference material and also real samples such as a tea and a swordfish sample purchased locally. Since the sensitivities of the elements studied in slurry and aqueous solution were different, an analyte addition technique was used for the determinations. The analytical results of the reference materials agreed with the certified values. The precision between sample replicates was better than 6% for all determinations. The method detection limit estimated from analyte addition curves was 0.01, 0.006, 0.007, 0.004, and 0.006 μg g⁻¹ for Fe, Co, Ni, Cu, and Zn, respectively, in the original biological samples.     

Determination of Arsenic and Vanadium in Airborne Related Reference Materials By ICP-MS

This study investigated sample digestion techniques and instrumental interference in determining As and V in airborne related reference materials using inductively coupled plasma mass spectrometry (ICP-MS). Four reference materials, NIST SRM 1648 urban particulate matter,BCR Reference Material No. 176 city waste incineration ash, NIST SRM 2709 San Joaquin soil, and NIST SRM 1633b coal fly ash were dissolved through acid mixture high-pressure bomb digestion.     

Determination of Pd,Rh, Pt,Au in road dust by electrothermal vaporization inductively coupled plasma mass spectrometry with slurry sampling

Inductively coupled plasma mass spectrometry coupled with ultrasonic slurry sampling electrothermal vaporization (USS-ETV-ICP-MS) has been applied to determine Pd, Rh, Pt and Au in 0.5% m/v slurries of several road dust samples. 2% m/v ammonium pyrrolidine dithiocarbamate (APDC) was used as the modifier to enhance the ion count. The influence of instrument operating conditions, slurry preparation and interferences on the ion count was reported. This method has been applied to the determination of Pd, Rh, Pt and Au in BCR 723 Road Dust and NIST SRM 2709 San Joaquin Soil reference materials and two road dust samples collected locally. The analysis results of the standard reference materials agreed with the certified values. Precision between sample replicates was better than 10% for all the determinations. The method detection limits estimated from standard addition curves were 0.9, 0.4, 0.6 and 0.4 ng g⁻¹ for Pd, Rh, Pt and Au, respectively, in original dust samples.     

Determination of hydride forming elements (As,Sb, Se,Sn) and Hg in environmental reference materials as acid slurries by on-line hydride generation inductively coupled plasma mass spectrometry

A method for the determination of As, Hg, Sb, Se and Sn in environmental and in geological reference materials, as acidified slurries, by flow injection (FI) coupled to a hydride generation system (HG) and detection by inductively coupled plasma mass spectrometry (ICP-MS) is proposed. The HG unit has a gas liquid separator and a drying unit for the generated vapor. The slurries were prepared by two procedures. Approximately 50 mg of the reference material, ground to a particle size ≤50 μm, was mixed with acid solutions in an ultrasonic bath. In Procedure A, the medium was a hydrochloric acid solution while in Procedure B, the medium was aqua regia plus a hydrochloric acid solution. The conditions for the slurry formation and the instrumental parameters were optimized. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming analytes to their lower oxidation states, As (III), Se(IV), Sb(III) and Sn(II), before reacting with sodium tetrahydroborate. To test the accuracy, 10 certified reference materials were analyzed (four sediments, three coals, one coal fly ash and two sewage sludges), with the analyte concentrations mostly in the μg g⁻¹ level. Good agreements with the certified values were obtained for Hg, Sb and Sn in the sediments using Procedure A and calibration against aqueous standard solutions. Using Procedure B, good results were obtained for Hg, Se and Sn in the sediment samples, for Se in the coal and coal fly ash samples and for Hg in the sewage sludge samples, also using external calibration with aqueous standard solutions. For As in sediments, coals and coal fly ash, Procedure B and the analyte addition calibration was required, indicating matrix effects. The relative standard deviations were lower than 5%, demonstrating a good precision for slurry analysis. The limits of quantification (10 times the standard deviation; n=10), in the samples, in ng g⁻¹, were: 20 for As, 60 for Hg, 80 for Sb, 200 for Se and 90 for Sn. The method requires small amounts of reagents and reduces contamination and losses.     

Microhomogeneity assessments using ultrasonic slurry sampling coupled with electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) is a very powerful technique for the direct analysis of solid materials prepared as slurries. The use of isotope dilution USS-ETV-ICP-MS (USS-ETV-ID-ICP-MS) for micro-homogeneity characterization studies of powdered reference materials based on elemental analyses, was investigated. Slurry analysis conditions were optimized taking into consideration density, particle size, analyte extraction, slurry mixing, analyte transport and sampling depth. Slurries were prepared using 1–20 mg of material and adding 1.0 ml of 5% nitric acid diluent containing 0.005% Triton X-100®. Three reference materials were analyzed (RM 8431a Mixed Diet, SRM 1548a Typical Diet and SRM 2709 San Joaquin Soil). Cu and Ni were determined in each material and Fe was also determined in RM 8431a Mixed Diet. ETV conditions were optimized and the benefit of using Pd as a carrier to enhance transport, combined with oxygen ashing was demonstrated. The accuracy of the method was verified by comparing analytical results with certified values. The precision of the method was demonstrated by comparing R.S.D.'s for slurry samples and aqueous standards and elemental ‘homogeneity’ was quantified based on the slurry sampling variability. The representative sample mass analyzed was calculated taking into consideration extraction of analyte into the liquid phase of the slurry. Representative sample masses of approximately 4 mg of RM 8431a provided slurry sampling variabilities of 10% or less for Cu, Fe and Ni. Representative sample masses of approximately 10 mg of SRM 1548a provided slurry sampling variabilities of approximately 10% for Cu and Ni. Representative sample masses of approximately 0.3 mg of SRM 2709 resulted in total analytical variabilities of less than 7%, highlighting the fact that the San Joaquin Soil is clearly the most homogeneous of the materials characterized.     

Investigations on the use of chemical modifiers for the direct determination of trace impurities in Al2O3 ceramic powders by slurry electrothermal evaporation coupled with inductively-coupled plasma mass spectrometry (ETV-ICP-MS)

The direct determination of trace impurities in Al2O3 ceramic basic powders by ICP-MS using electrothermal evaporation (ETV) with slurry sampling has been investigated. To increase interference-free analyte volatilization, the use of the palladium-group modifiers (PGM) IrCl3, Pd(NO3)2, and PdCl2 for the determination of Ca, Fe, Ga, Mg, Mn, Na, Ni, and V in Al2O3 powders was studied. Their role, which in ETV-ICP-MS and ETV-ICP-OES is to stabilize the investigated analyte during the ashing phase, to increase vaporization of the matrix, and to reduce transport losses was investigated. Optimum analysis results were obtained with PdCl2 modifier when 500 ng Pd was used for a sample weight of 100 microg Al2O3 injected into the ETV. Calibration was performed by standard addition with aqueous solutions of the analytes. The RSDs calculated from triplicate analysis ranged form 5 to 10%. Detection limits between 0.07 microg g(-1) (Ga) and 1.1 microg g(-1) (Na) were achieved. The accuracy was proven for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V by analyzing an NIST standard reference Al2O3 material (SRM 699) with a middle grain size of 16.4 microm. The analytical method was used for the analysis of Al2O3 powder (AKP 30, Sumitomo, Japan) with impurities in the low microg g(-1) range and a middle grain size of 1.1 microm. The results obtained for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V were comparable with those obtained by ICP-MS subsequent to conventional decomposition with hydrochloric acid at high pressure.     

Speciation of selenium(IV) and selenium(VI) in environmental samples by the combination of graphite furnace atomic absorption spectrometric determination and solid phase extraction on Diaion HP-2MG

A simple solid phase extraction procedure for speciation of selenium(IV) and selenium(VI) in environmental samples has been proposed prior to graphite furnace atomic absorption spectrometry. The method is based on the solid phase extraction of the selenium(IV)-ammonium pyrrolidine dithiocarbamate (APDC) chelate on the Diaion HP-2MG. After reduction of Se(VI) by heating the samples in the microwave oven with 4 mol l⁻¹ HCl, the system was applied to the total selenium. Se(VI) was calculated as the difference between the total selenium content and Se(IV) content. The experimental parameters, pH, amounts of reagents, eluent type and sample volume were optimized. The recoveries of analytes were found greater than 95%. No appreciable matrix effects were observed. The adsorption capacity of sorbent was 5.20 mg g⁻¹ Se (IV). The detection limit of Se (IV) (3sigma, n = 11) is 0.010 μg l⁻¹. The preconcentration factor for the presented system was 100. The proposed method was applied to the speciation of selenium(IV), selenium(VI) and determination of total selenium in natural waters and microwave digested soil, garlic, onion, rice, wheat and hazelnut samples harvested various locations in Turkey with satisfactory results. In order to verify the accuracy of the method, certified reference materials (NIST SRM 2711 Montana Soil, NIST SRM 1568a Rice Flour and NIST SRM 8418 Wheat Gluten) were analyzed and the results obtained were in good agreement with the certified values. The relative errors and relative standard deviations were below 6 and 10%, respectively.     

Direct solid sampling electrothermal vaporization of alumina for analysis by inductively coupled plasma optical emission spectrometry

A procedure based on electrothermal evaporation (ETV) and inductively coupled plasma atomic emission spectrometry (ICP-OES) for the determination of trace impurities in Al₂O₃ powders without any sample pretreatment is presented. With the aid of matrix modifier the transport and the evaporation efficiency for refractory compounds could be increased by forming halides with a lower boiling point. As calibration is still a problem in direct solid sample analysis, different calibration approaches including the use of certified reference materials from NIST and standard addition of aqueous solutions of analytes were discussed. The accuracy obtained with calibration and with the standard addition method was shown up for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni and V for the case of Al₂O₃ NIST standard reference material (SRM 699). The ETV–ICP-OES method was used for the analysis of Al₂O₃ powders with impurities in the low μg/g range and the results for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni and V obtained with evaporation of discrete powder amounts with ETV–ICP-OES and slurry evaporation under the use of ultrasonic homogenization during the sampling and ETV–ICP-MS were shown to be in a good agreement.     

Determination of cadmium,mercury and lead in coal fly ash by slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry (USS-ETV-ID-ICP-MS) has been applied to the determination of Cd, Hg and Pb in coal fly ash samples. Thioacetamide (TAC) was used as the modifier. Since the sensitivities of the elements studied in coal fly ash slurry and aqueous solution were quite different, isotope dilution method was used for the determination of Cd, Hg and Pb in these coal fly ash samples. The isotope ratios of each element were calculated from the peak areas of each injection peak. This method has been applied to the determination of Cd, Hg and Pb in NIST SRM 1633a coal fly ash reference material and a coal fly ash sample collected from Kaohsiung area. Analysis results of reference sample NIST SRM 1633a coal fly ash agreed satisfactorily with the certified values. The other sample determined by isotope dilution and method of standard additions was agreed satisfactorily. Precision was better than 6% for most of the determinations and accuracy was better than 4% with the USS-ETV-ID-ICP-MS method. Detection limits estimated from standard addition curves were in the range of 24–58, 6–28 and 108–110 ng g⁻¹ for Cd, Hg and Pb, respectively.     

The determination of arsenic and selenium in standard reference materials using sector field ICP-MS in high resolution mode

Sector field ICP-MS was used to analyse As and Se in a range of standard reference materials (NIST 1643d Water, NIST 1573a Tomato Leaves, NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine Level 2). A spectral resolution of m/Δm = 7500 enabled ⁷⁵As and ⁷⁷Se to be separated from problematic ArCl interferences. Following microwave acid digestion, solid samples were typically diluted 1 + 99 prior to analysis, while the urine sample was diluted 1 + 9. The water sample was analysed undiluted and diluted 1 + 9. Despite near baseline spectral separation, ⁷⁵As and ⁷⁷Se were still found to be influenced by ArCl at high Cl concentrations, the effect being most pronounced for ⁷⁷Se. When necessary ⁸²Se was also monitored to determine the accuracy of the ⁷⁷Se results. Detection limits (LOD, based on 3σ of 10 replicates) for ⁷⁵As, ⁷⁷Se and ⁸²Se in ultra-pure water, 1% (w/w) HNO₃ and 1% (w/w) HCl were ～?0.1, ～?0.2 and ～?0.5 ng g^–1, respectively. Although signal intensities when using high resolution were ～?1% of that found when using low resolution mode (m/Δm = 300), measured As concentrations and certified values were found to agree to within ± 11% for all samples analysed. The concentration of Se in NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine were found to be in agreement with certified values to within ± 15– 20%, as measured by ⁷⁷Se. However, closer agreement (± 5%) was found when these samples were analysed using ⁸²Se. The Se concentration in NIST 1643d Water was found to agree to within ± 5% of the certified value (depending on dilution factor). Due to the low concentration of Se in NIST 1573a Tomato Leaves, quantitation was not possible (below LOQ, 10σ). As a consequence of the lower ion transmission when using resolution 7500, analytical precisions were found to be elevated over that normally observed using low resolution mode, typically ± 5–20% (depending on analyte concentration and isotopic abundance).     

Analysis of solid samples by ICP-mass spectrometry

Summary ICP-Mass spectrometry is typically used as a technique for very rapid multielement analysis at trace and ultra-trace levels of solutions by continuous sample aspiration and nebulization. However, ICP-MS is well suited to be used as a detector for other sample introduction devices. For the analysis of solid samples laser sampling and electrothermal vaporization accessories may be used as sample introduction devices for ICP-MS. Laser sampling permits the analysis of many different types of solid materials. For solid sampling ETV-ICP-MS analysis it is of advantage to reduce the sample to a fine powder prior to analysis. For automated analysis powders may be introduced as slurries into the graphite furnace by means of a slurry sampling device. Since appropriate certified solid reference materials are not always available for calibration, or since they are not certified for all analyte elements of interest, the analyses discussed in this contribution were performed semiquantitatively. The instrument response function was established using reference materials which were similar in their composition to the samples. The results of semiquantitative bulk analyses of glass (NIST 612) and geological material (USGS GXR-3) by laser sampling ICP-MS are in good agreement with the certified values. The concentrations of the analytes determined in the glass sample were in the range of 10 g/g to 80 g/g. The lowest analyte concentration in the geological sample was 0.4 g/g (Eu) and the highest was approximately 186 mg/g (Fe). The precision achieved was in the order of 5% to 15%. Laser sampling ICP-MS is not only suitable to bulk analysis but also to analyses where spatial information is required. As an example for such an application the determination of Pb in a wine bottle cork stopper is dicussed. The slurry sampling technique was used for the semiquantitative analysis of NIST coal reference samples by electrothermal vaporization ICP-MS. The accuracy achieved with this approach was within a factor of ±2 of the reference values.     

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 degrees C whereas at -20 degrees C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%.     

Determination of Mercury in Urine and Seawater by Flow Injection Vapor Generation Isotope Dilution Inductively Coupled Plasma Mass Spectrometry

A simple and inexpensive laboratory-built vapor generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of mercury in urine and seawater samples. The applications of vapor generation ICP-MS alleviated the non-spectroscopic interferences and the sensitivity problem of mercury determination encountered when the conventional pneumatic nebulizer was used for sample introduction. The concentration of mercury was determined by isotope dilution method. The isotope ratio of mercury was calculated from the peak areas of each injection peak. The repeatability of the peak areas and isotope ratio determinations of seven consecutive injections of 1 ng mL^?1 Hg solution were 2.3% and 2.2%, respectively. This method has a detection limit of 0.07 ng mL^?1 for mercury. This method was applied to determine mercury in a CASS-3 nearshore seawater reference sample, NASS-4 open ocean seawater reference sample, NIST SRM 2670 freeze-dried urine reference sample and several urine and seawater samples collected from National Sun Yat-Sen University. The results for the reference samples agreed satisfactorily with the reference values. Results for other samples analyzed by the isotope dilution method and the method of standard additions agreed satisfactorily. Precision was better than 10% for most of the determinations.     

Determination of manganese in brain samples by slurry sampling graphite furnace atomic absorption spectrometry

A simple procedure for the determination of manganese in different sections of human brain samples by graphite furnace atomic absorption spectrometry has been developed. Brain sections included cerebellum, hypothalamus, frontal cortex, vermix and encephalic trunk. Two sample preparation procedures were evaluated, namely, slurry sampling and microwave-assisted acid digestion. Brain slurries (2% w/v) could be prepared in distilled, de-ionized water, with good stability for up to 30 min. Brain samples were also digested in a domestic microwave oven using 5 ml of concentrated HNO₃. A mixed palladium+magnesium nitrate chemical modifier was used for thermal stabilization of the analyte in the electrothermal atomizer up to pyrolysis temperatures of 1300 °C, irrespective of the matrix. Quantitation of manganese was conducted in both cases by means of aqueous standards calibration. The detection limits were 0.3 and 0.4 ng ml⁻¹ for the slurry and the digested samples, respectively. The accuracy of the procedure was checked by comparing the results obtained in the analysis of slurries and digested brain samples, and by analysis of the NIST Bovine Liver standard reference material (SRM 1577a). The ease of slurry preparation, together with the conventional set of analytical and instrumental conditions selected for the determination of manganese make such methodology suitable for routine clinical applications.     

Application of tertiary amines for arsenic and selenium signal enhancement and polyatomic interference reduction in ICP-MS analysis of biological samples

Water soluble tertiary amines enhance signals and decrease polyatomic chloride interferences in the direct inductively coupled plasma – mass spectrometric (ICP-MS) determination of As and Se in biological samples. Preliminary experiments with amine concentrations and nebulizer flow rates produced element and interference signal intensity changes. Arsenic and Se ICP-MS determination parameters have been optimized by a simplex procedure with amines in an argon plasma or without amines but with addition of N₂ to the Ar. Variables include RF (radio frequency) power, nebulizer gas flow rate, intermediate gas flow rate, and amine concentration or nitrogen gas flow rate. Detection limit, minimization of polyatomic ion intensities, and reproducibility have been evaluated as reponse factors. The signal enhancement and element-to-molecular interference ratios differ to some extent with analyte intensity optimum operating conditions. The detection limits with addition of nitrogen (16 pg mL^–1 for As and 180 pg mL^–1 for Se) or of amines (8 pg mL^–1 for As and 120 pg mL^–1 for Se) and the extent of chloride interference minimization were compared. Amines addition was more beneficial. Biological standard reference materials and food and fecal samples were analyzed following different sample dissolution procedures.     

Application of tertiary amines for arsenic and selenium signal enhancement and polyatomic interference reduction in ICP-MS analysis of biological samples

Water soluble tertiary amines enhance signals and decrease polyatomic chloride interferences in the direct inductively coupled plasma – mass spectrometric (ICP-MS) determination of As and Se in biological samples. Preliminary experiments with amine concentrations and nebulizer flow rates produced element and interference signal intensity changes. Arsenic and Se ICP-MS determination parameters have been optimized by a simplex procedure with amines in an argon plasma or without amines but with addition of N₂ to the Ar. Variables include RF (radio frequency) power, nebulizer gas flow rate, intermediate gas flow rate, and amine concentration or nitrogen gas flow rate. Detection limit, minimization of polyatomic ion intensities, and reproducibility have been evaluated as reponse factors. The signal enhancement and element-to-molecular interference ratios differ to some extent with analyte intensity optimum operating conditions. The detection limits with addition of nitrogen (16 pg mL^–1 for As and 180 pg mL^–1 for Se) or of amines (8 pg mL^–1 for As and 120 pg mL^–1 for Se) and the extent of chloride interference minimization were compared. Amines addition was more beneficial. Biological standard reference materials and food and fecal samples were analyzed following different sample dissolution procedures.     

Inductively Coupled Plasma Mass Spectrometry for Sequential Determination of Trace Metals in Rain and River Waters Using Electrothermal Vaporization

Abstract

The sequential determination of 14 trace metals, Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Mo, Cd, Sb and Pb, in rain and river water samples has been investigated using an inductively coupled plasma mass spectrometry (ICP-MS) with a graphite rod electrothermal vaporizer (ETV) in the presence of the mixed modifier of palladium nitrate and magnesium nitrate. The sensitivity enhancements due to the presence of the modifier were observed for all analyte elements. Detection limits as high as 0.52, 0.13, 0.89, 0.35, 1.76, 0.5, 0.9, 0.5, 0.04, 1.03, 0.28, 0.07, 0.1 and 3.78 pg, respectively, for Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Mo, Cd, Sb and Pb have been achieved. For the determination of trace metals in both rain and river water samples by this method, the repeatibility of sample solution were very good, i.e. from 1% to 7% (as a coefficient variation) and the recoveries of elements were good enough, i.e. from 81% to 106%, by using a standard addition method. There was no difference between the results obtained by nebulizer ICP-MS and those obtained by this method, except for zinc and arsenic.     

The determination of arsenic and selenium in standard reference materials using sector field ICP-MS in high resolution mode

Sector field ICP-MS was used to analyse As and Se in a range of standard reference materials (NIST 1643d Water, NIST 1573a Tomato Leaves, NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine Level 2). A spectral resolution of m/Δm = 7500 enabled ⁷⁵As and ⁷⁷Se to be separated from problematic ArCl interferences. Following microwave acid digestion, solid samples were typically diluted 1 + 99 prior to analysis, while the urine sample was diluted 1 + 9. The water sample was analysed undiluted and diluted 1 + 9. Despite near baseline spectral separation, ⁷⁵As and ⁷⁷Se were still found to be influenced by ArCl at high Cl concentrations, the effect being most pronounced for ⁷⁷Se. When necessary ⁸²Se was also monitored to determine the accuracy of the ⁷⁷Se results. Detection limits (LOD, based on 3σ of 10 replicates) for ⁷⁵As, ⁷⁷Se and ⁸²Se in ultra-pure water, 1% (w/w) HNO₃ and 1% (w/w) HCl were ∼ 0.1, ∼ 0.2 and ∼ 0.5 ng g^–1, respectively. Although signal intensities when using high resolution were ∼ 1% of that found when using low resolution mode (m/Δm = 300), measured As concentrations and certified values were found to agree to within ± 11% for all samples analysed. The concentration of Se in NIST 1566a Oyster Tissue, NIST 2704 Buffalo River Sediment and Bio-Rad Reference Urine were found to be in agreement with certified values to within ± 15– 20%, as measured by ⁷⁷Se. However, closer agreement (± 5%) was found when these samples were analysed using ⁸²Se. The Se concentration in NIST 1643d Water was found to agree to within ± 5% of the certified value (depending on dilution factor). Due to the low concentration of Se in NIST 1573a Tomato Leaves, quantitation was not possible (below LOQ, 10σ). As a consequence of the lower ion transmission when using resolution 7500, analytical precisions were found to be elevated over that normally observed using low resolution mode, typically ± 5–20% (depending on analyte concentration and isotopic abundance). Received: 28 December 1998 / Accepted: 9 February 1999     

Determination of arsenic, selenium, and antimony in cloud water by inductively coupled plasma mass spectrometry

The capability of inductively coupled plasma mass spectrometry in determining trace levels of As, Se, and Sb in cloud water was evaluated. Preliminary studies focused on identifying and eliminating potential interferences in the cloud water matrix, the choice of appropriate internal standards, and system optimization. The detection limits for As, Se, and Sb were 20, 100, 20 pg/mL using pneumatic nebulization, and 5, 25, 5 pg/mL, respectively, using ultrasonic nebulization with a precision of better than 5% RSD. The accuracy was demonstrated by the analysis of a NIST commercial reference material, SRM 1643d. In all cases, the results from ICP-MS analysis agreed within 4% of the certified values. Comparative analysis of cloud water samples obtained from a site downwind from large pollution sources (Whiteface Mountain, New York) and Changlagali Pakistan, a rural mountain peak, was carried out by hydride generation atomic absorption (HGAA) spectrometry. There was excellent agreement between the ICP-MS and HGAA results.