Static and dynamic superheated water extraction of essential oil components from Thymus vulgaris L.

Superheated water extraction (SWE) performed in both static and dynamic condition (S‐SWE and D‐SWE, respectively) was applied for the extraction of essential oil from Thymus vulgaris L. The influence of extraction pressure, temperature, time, and flow rate on the total yield of essential oil and the influence of extraction temperature on the extraction of some chosen components are discussed in the paper. The SWE extracts are related to PLE extracts with n‐hexane and essential oil obtained by steam distillation. The superheated water extraction in dynamic condition seems to be a feasible option for the extraction of essential oil components from T. vulgaris L.     

Comparison of different extraction methods for the determination of essential oils and related compounds from aromatic plants and optimization of solid-phase microextraction/gas chromatography

Different extraction methods for the subsequent gas chromatographic determination of the composition of essential oils and related compounds from marjoram (Origanum majorana L.), caraway (Carum carvi L.), sage (Salvia officinalis L.), and thyme (Thymus vulgaris L.) have been compared. The comparison was also discussed with regard to transformation processes of genuine compounds, particularly in terms of expenditure of time. Hydrodistillation is the method of choice for the determination of the essential oil content of plants. For investigating the composition of genuine essential oils and related, aroma-active compounds, hydrodistillation is not very useful, because of discrimination and transformation processes due to high temperatures and acidic conditions. With cold solvent extraction, accelerated solvent extraction, and supercritical fluid extraction, discrimination of high and non-volatile aroma-active components as well as transformation processes can be diminished, but non-aroma-active fats, waxes, or pigments are often extracted, too. As solid-phase microextraction is a solvent-free fully automizable sample preparation technique, this was the most sparing to sensitive components and the most time-saving method for the rapid determination of the aroma compounds composition in marjoram, caraway, sage, and thyme. Finally, solid-phase microextraction could be successfully optimized for the extraction of the aroma components from the plants for their subsequent gas chromatographic determination.     

Solid-phase microextraction of hop volatiles. Potential use for determination and verification of hop varieties

The composition of hop essential oil is an important tool for evaluation of hop quality. As each hop variety has a typical essential oil pattern (fingerprint), hop oil analyses can be used to distinguish between hop varieties. The headspace solid-phase microextraction (SPME) method as described in this contribution is a simple sample preparation technique and represents an alternative procedure for essential oil fingerprint determination. Different SPME parameters (extraction temperature, extraction time and sample mass) were studied and the results were compared with those obtained by the routine distillation method. It is shown that SPME results can be used for determination and verification of varieties grown in Slovenia by means of principal components analysis.     

Analysis of terpenoic composition of conifer needle oils by steam distillation/extraction,gas chromatography and gas chromatography-mass spectrometry

Summary The essential oils of Estonian spruce and pine needles have been analysed by a combination of steam distillation/extraction, GC and GC-MS. According to their monoterpene composition Estonian pines belong to a high carene chemotype with monoterpenes representing up to 85% of total oil. Estonian spruce needle oil contains up to 70% of oxygenated terpenes and more limonene and 1,8-cineole than the same spruce species [Picea abies (L.) Karst.] from other localities.A total of 60 components were identified. Coefficients of variation describe the range of component contents in individual trees within the population.     

GC-MS of volatile components of Schisandra chinensis obtained by supercritical fluid and conventional extraction

In this paper, the volatile compounds of Schisandra chinensis obtained by different extraction techniques including supercritical fluid extraction (SFE), steam distillation (SD), Soxhlet extraction (SE) and ultrasound-assisted extraction (UAE) were investigated for the first time. The sample preparation procedure for GC-MS analysis of the volatile compounds was optimized and then 37, 45, 27 and 37 compounds were identified in the samples obtained by SFE, SD, SE and UAE methods, respectively. As the therapeutic effect of the traditional Chinese medicine is usually based on multifarious essential components or the combination of them instead of only one component, the volatile compounds were compared in groups with the extracts by SE, SD and UAE. This would be more reasonable to evaluate the effects of an alternative technique to extracting multifarious essential components. Among the identified components in the SFE extract, 32 compounds were the same as that by three conventional methods, accounting for 90.5% of the volatile compounds identified. However, as the volatile compounds were classed into groups, it was easy to see that the Schisandra chinensis oil extracted by SFE was made up largely of aromatics and sesquiterpenoids (52.1 and 27.6%, respectively), with less amounts of monoterpenoids and other compounds, distinguishing SFE from the conventional extractions.     

Supercritical extraction of thyme (Thymus vulgaris L.)

Summary Chromatographic methods for the qualitative and quantitative analysis of thyme (Thymus vulgaris L.) extracts (essential oil obtained by steam distillation and extracts obtained by carbon dioxide supercritical fluid extraction and methylene chloride) are described. The composition of extracts obtained at different pressures (from 80 bar to 400 bar) and constant temperature (40°C) is discussed. The extraction system thyme— supercritical carbon dioxide was modelled by empirical equations defining the dependence of the total extract (TE) solubility and thymol solubility in CO₂ on the density of carbon dioxide.     

Reporting effective extraction methodology and chemical characterization of bioactive components of under explored Platycladus orientalis (L.) Franco from semi-arid climate

The bioactive ingredients of many essential oils are complex and difficult to reproduce synthetically. In the present study, the influence of extraction method on relative extraction of bioactive compounds of essential oil of Platycladus orientalis (L.) Franco (Thuja orientalis L. is a synonym of it) leaves gathered from semi-arid climate was studied. A higher yield of essential oil was obtained by hydrodistillation (0.1%) as compared to steam distillation (0.07%) under newly optimized conditions. Initial analysis of these oils by TLC showed the presence of different polarity groups ranging from non-polar terpene hydrocarbons to polar terpenoid alcohols. GC-MS analysis revealed that major component of hydrodistilled essential oil of Platycladus orientalis (L.) Franco leaves was α-pinene (17.83%) and steam distilled essential oil contained α-cedrol (12.44%). The results obtained in the present study emphasize that suitable extraction technique should be used to obtain particular component of interest.     

Ionic‐liquid‐assisted microwave distillation coupled with headspace single‐drop microextraction followed by GC–MS for the rapid analysis of essential oil in Dryopteris fragrans

A rapid, green and effective miniaturized sample preparation technique, ionic‐liquid‐assisted microwave distillation coupled with headspace single‐drop microextraction was developed for the extraction of essential oil from dried Dryopteris fragrans. 1‐Ethyl‐3‐methylimidazolium acetate was the optimal ionic liquid as the destruction agent of plant cell walls and microwave absorption was medium. n‐Heptadecane (2.0 μL) was adopted as the suspended microdrop solvent in the headspace for the extraction and concentration of essential oil. The optimal parameters of the proposed method were an irradiation power of 300 W, sample mass of 0.9 g, mass ratio of ionic liquids to sample of 2.8, extraction temperature of 79°C, and extraction time of 3.6 min. In comparison to the previous reports, the proposed technique could equally monitor all the essential oil components with no significant differences in a simple way, which was more rapid and required a much lower amount of sample.     

Rapid determination of essential oil compounds in Artemisia Selengensis Turcz by gas chromatography-mass spectrometry with microwave distillation and simultaneous solid-phase microextraction

In the work, for the first time, two solvent-free sample preparation techniques of microwave distillation (MD) and solid-phase microextraction (SPME) were combined, and developed for determination of essential oil compounds in traditional Chinese medicine (TCM). Using the proposed method, isolation, extraction and concentration of TCM essential oil compounds can be carried out in a single step. To demonstrate its feasibility, MD-SPME was compared with a conventional technique, steam distillation (SD), for gas chromatography-mass spectrometry (GC-MS) analysis of essential oil compounds in a TCM, Artemisia Selengensis Turcz. Forty-nine compounds in the TCM were separated and identified by the present method, while only 26 compounds were detected by SD method. Relative standard deviation (R.S.D.) values less than 9% show that the present method has good precision. The SD method required long time (6 h) to isolate of the essential oil, and large amount of organic solvent for further extraction, while MD-SPME needed little time (only 3 min) to prepare sample, and no organic solvent. These results show that MD-SPME-GC-MS is a simple, rapid and solvent-free method for determination of TCM essential oil.     

Ionic liquid-based microwave-assisted extraction of essential oil and biphenyl cyclooctene lignans from Schisandra chinensis Baill fruits

Ionic liquid-based microwave-assisted extraction (ILMAE) has been successfully applied in extracting essential oil and four kinds of biphenyl cyclooctene lignans from Schisandra chinensis Baill. 0.25 M 1-lauryl-3-methylimidazolium bromide ionic liquid is selected as solvent. The optimum parameters of dealing with 25.0 g sample are 385 W irradiation power, 40 min microwave extraction time and 1:12 solid-liquid ratio. The yields of essential oil and lignans are 12.12±0.37 ml/kg and 250.2±38.2 mg/kg under the optimum conditions. The composition of the essential oil extracted by hydro-distillation, steam-distillation and ILMAE is analyzed by GC-MS. With ILMAE method, the energy consumption time has not only been shortened to 40 min (hydro-distillation 3.0 h for extracting essential oil and reflux extraction 4.0 h for extracting lignans, respectively), but also the extraction efficiency has been improved (extraction of lignans and distillation of essential oil at the same time) and reduces the environmental pollution. S. chinensis materials treated by different methods are observed by scanning electronic microscopy. Micrographs provide more evidence to prove that ILMAE is a better and faster method. The experimental results also indicate that ILMAE is a simple and efficient technique for sample preparation.     

Variation in essential oil content and composition of Ridolfia segetum Moris based on 30-hour prolonged fractionated extraction procedure

Abstract

A comprehensive study on essential oil samples extracted from Ridolfia segetum Moris (Apiaceae) collected in Tarquinia (Italy) is reported. In this study, a 30-hour, fractionated, steam distillation procedure for essential oil preparation was applied. The gas chromatographic-mass spectrometry analysis showed monoterpene o-cymene and phenylpropanoid dill-apiol as the major essential oil’s constituents revealing a new chemotype dependent on extraction duration. Great impact of the duration of the distillation process on chemical profile of essential oil was observed; prolonged distillation gives chemically more diverse essential oil samples. Preliminary microbiological evaluations of the essential oils samples revealed some activity, although not high, against Candida albicans.     

气相色谱-质谱法测定阿尔泰狗娃花挥发精油中化学成分

采用水蒸气回流法提取阿尔泰狗娃花挥中挥发精油,用气相色谱-质谱法分离和鉴定阿尔泰狗娃花挥发精油中化学成分,用归一法测定其相对含量,共分离出50种化学成分,鉴定了39种化学成分,约占总成分相对含量的84.7%。     

Water as a green solvent combined with different techniques for extraction of essential oil from lavender flowers

Using water as a green solvent with a variable geometry makes use of physical and chemical phenomena that are fundamentally different from those applied in conventional extraction techniques such as hydro-distillation, steam distillation or solvent extraction. Advantages and drawbacks of using water as a solvent with different physical and chemical states have been compared. A total of ten extraction techniques: hydro-distillation (HD), steam distillation (SD), turbo-hydro-distillation (THD), salt-hydro-distillation (NaCL-HD), enzyme-hydro-distillation (Enzyme-HD), micelle-hydro-distillation (Micelle-HD), ultrasound-hydro-distillation (US-HD) or subcritical water-hydro-distillation (SW-HD), solvent-free microwave extraction (SFME) and microwave steam distillation (MSD) were used to extract the essential oil from lavender (Lavandula L.) and their results were compared. The quantity was measured by the yield of essential oil and the quality was evaluated using the oil composition especially the content of linalyl acetate, linalool and terpin-4-ol compared with the corresponding control sample: Hydro-distillation. For environmentally friendly of the process: extraction time, total energy consumption and CO₂ emission were considered and compared with conventional hydro-distillation. The mechanism explaining the linalyl acetate degradation has been resolved by using COSMO-RS software. Based on the present experimental conditions, it is recommended that lavender oil may be produced preferably by steam distillation assisted by microwave extraction to reduce the by-product formation by various chemical reactions and to get better oil recoveries.     

Rapid analysis of the essential oil components of dried Zanthoxylum bungeanum Maxim by Fe2O3‐magnetic‐microsphere‐assisted microwave distillation and simultaneous headspace single‐drop microextraction followed by GC–MS

In this work, microwave distillation assisted by Fe₂O₃ magnetic microspheres (FMMS) and headspace single‐drop microextraction were combined, and developed for determination of essential oil compounds in dried Zanthoxylum bungeanum Maxim (ZBM). The FMMS were used as microwave absorption solid medium for dry distillation of dried ZBM. Using the proposed method, isolation, extraction, and concentration of essential oil compounds can be carried out in a single step. The experimental parameters including extraction solvent, solvent volume, microwave power, irradiation time, and the amount of added FMMS, were studied. The optimal analytical conditions were: 2.0 μL decane as the extraction solvent, microwave power of 300 W, irradiation time of 2 min, and the addition of 0.1 g FMMS to ZBM. The method precision was from 4 to 10%. A total of 52 compounds were identified by the proposed method. The conventional steam distillation method was also used for the analysis of essential oil in dried ZBM and only 31 compounds were identified by steam distillation method. It was found that the proposed method is a simple, rapid, reliable, and solvent‐free technique for the determination of volatile compounds in Chinese herbs.     

Surfactant-assisted pressurized liquid extraction for determination of flavonoids from Costus speciosus by micellar electrokinetic chromatography

Micellar electrokinetic chromatography (MEKC), a mode of capillary electrophoresis (CE), is considered an efficient analytical technique allowing for the reduction of organic solvent consumption during the experimental procedure. However, during sample preparation of natural products, the usage of large amount of organic solvent is generally unavoidable. In this article, therefore, a fast, simple, efficient, highly automatic and organic solvent-free sample preparation method, namely surfactant-assisted pressurized liquid extraction (PLE), was developed for the extraction of flavonoids in Costus speciosus flowers before MEKC analysis. The various experimental parameters such as the type and concentration of surfactant, and extraction time were evaluated systematically. Under the optimized conditions, the extraction efficiencies of surfactant-assisted PLE methods were comparable with Soxhlet extraction using organic solvent. The combination of surfactant-assisted PLE and MEKC was shown to be a green, rapid and effective approach for extraction and analysis of flavonoids in C. speciosus flowers.     

Ultrasound-assisted dynamic extraction of valuable compounds from aromatic plants and flowers as compared with steam distillation and superheated liquid extraction

A method for the extraction of valuable compounds from plants and flowers (viz. laurel, rosemary, thyme, oregano and tuberose) is proposed. The dynamic approach allows go-and-backward circulation of the extractant (ethanol) through the solid sample subjected to the action of an ultrasound probe (thus reducing sample amount and avoiding overpressure). A multivariate optimisation study and application of the optimum values of the variables to kinetics studies show that 10 min is sufficient to obtain extraction efficiencies that greatly surpass those provided by steam distillation for essential oils or superheated liquid extraction for these oils and other valuable compounds, with lower costs and higher quality of the extract. The extraction time of the proposed method is 176–165 min shorter than steam distillation and 31–20 min shorter than superheated liquid extraction, depending on the target compound.     

Innovation in a Continuous System of Distillation by Steam to Obtain Essential Oil from Persian Lime Juice (Citrus latifolia Tanaka)

The citrus industry is one of the most important economic areas within the global agricultural sector. Persian lime is commonly used to produce lime juice and essential oil, which are usually obtained by batch distillation. The aim of this work was to validate a patented continuous steam distillation process and to both physically and chemically characterize the volatile fractions of essential Persian lime oil. Prior to distillation, lime juice was obtained by pressing the lime fruit. Afterwards, the juice was subjected to a continuous steam distillation process by varying the ratio of distillate flow to feed flow (0.2, 0.4, and 0.6). The distillate oil fractions were characterized by measuring their density, optical rotation, and refractive index. Gas chromatography GC-FID was used to analyze the chemical compositions of the oil fractions. The process of continuous steam distillation presented high oil recovery efficiencies (up to 90%) and lower steam consumption compared to traditional batch process distillation since steam consumption ranged from 32 to 60% for different steam levels. Moreover, a reduction in process time was observed (from 8 to 4 h). The oil fractions obtained via continuous steam distillation differed significantly in their composition from the parent compounds and the fractions.     

Superheated water extraction, steam distillation and Soxhlet extraction of essential oils of Origanum onites

Superheated water extraction (SWE) at various temperatures (100, 125, 150 and 175°C), steam distillation, and Soxhlet extraction were compared in the extraction of essential oils from two samples of the plant Origanum onites, one cultivated, the other wild. C18 solid-phase extraction was used to elute the essential oils from the SWE aqueous extract. The compositions of the extracted essential oils obtained from all three methods were then characterized by comprehensive GC×GC/time-of-flight mass spectrometry (TOF/MS). The highest essential oil yields were obtained by using SWE at 150°C with a flow rate of 2 mL min^–1 and a pressure of 60 bar for 30 min: these were 3.76 and 4.11% for wild and cultivated O. onites samples, respectively, expressed as a percentage of 100 g of dry (leaf) matter. The yields obtained using SWE at 150°C were slightly higher than those from conventional methods. Steam distillation was performed for 3 h, and Soxhlet extraction was completed in 12 h. The major compounds found were borneol, terpinen-4-ol and carvacrol.     

Qualitative evaluation of aromatic herbs by direct headspace GC analysis. Applications of the method and comparison with the traditional analysis of essential oils

GC headspace analyses of various aromatizing herbs have been compared with those relating to the essential oils, obtained by steam distillation, of the same plants. In this way it was possible to establish the most significant differences between the composition of a herb flavor and that of its essential oil. In particular, we observed some very volatile compounds in the headspace samples which were absent from the essential oil; these components may make an important contribution to the herb flavor. The identification of these substances is still in progress.