High resolution electron microscopy of ordered polymers and organic molecular crystals: Recent developments and future possibilities

High Resolution Electron Microscopy (HREM) has made it possible to directly image the detailed organization of a variety of polymers and organic molecular crystals. For organic materials it is imperative to use low dose techniques that minimize the structural reorganizations that inevitably occur during electron beam irradiation. This article reviews recent developments in low dose HREM from our own laboratory and elsewhere. The developments in closely related microstructural characterization techniques are also reviewed. In the future, the ability to correct the spherical aberration of the objective lens, the use of low voltages to increase contrast, and the use of time‐resolved techniques are expected to open new avenues for the ultrastructural investigations of organic materials. New sample preparation techniques, such as the ability to make thin samples by focused ion beam (FIBs), to cut samples with an oscillating diamond knife, and to more conveniently prepare cryogenically solidified specimens, are also expected to be of increasing importance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1749–1778, 2005     

Evaluation and optimization of electron capture dissociation efficiency in fourier transform ion cyclotron resonance mass spectrometry

Electron capture dissociation (ECD) efficiency has typically been lower than for other dissociation techniques. Here we characterize experimental factors that limit ECD and seek to improve its efficiency. Efficiency of precursor to product ion conversion was measured for a range of peptide (∼15% efficiency) and protein (∼33% efficiency) ions of differing sizes and charge states. Conversion of precursor ions to products depends on electron irradiation period and maximizes at ∼5–30 ms. The optimal irradiation period scales inversely with charge state. We demonstrate that reflection of electrons through the ICR cell is more efficient and robust than a single pass, because electrons can cool to the optimal energy for capture, which allows for a wide range of initial electron energy. Further, efficient ECD with reflected electrons requires only a short (∼500 μs) irradiation period followed by an appropriate delay for cooling and interaction. Reflection of the electron beam results in electrons trapped in or near the ICR cell and thus requires a brief (∼50 μs) purge for successful mass spectral acquisition. Further electron irradiation of refractory precursor ions did not result in further dissociation. Possibly the ion cloud and electron beam are misaligned radially, or the electron beam diameter may be smaller than that of the ion cloud such that remaining precursor ions do not overlap with the electron beam. Several ion manipulation techniques and use of a large, movable dispenser cathode reduce the possibility that misalignment of the ion and electron beams limits ECD efficiency.     

Electron capture dissociation Fourier transform ion cyclotron resonance mass spectrometry in the electron energy range 0-50 eV

Electron capture dissociation (ECD) of polypeptide cations was obtained with pencil and hollow electron beams for both sidekick and gas-assisted dynamic ion trapping (GADT) using Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) with an electrostatic ion transfer line. Increasing the number of trapped ions by multiple ICR trap loads using GADT improved the ECD sensitivity in comparison with sidekick ion trapping and ECD efficiency in comparison with single ion trap load by GADT. Furthermore, enhanced sensitivity made it possible to observe ECD in a wide range of electron energies (0-50 eV). The degree, rate and fragmentation characteristics of ECD FTICR-MS were investigated as functions of electron energy, electron irradiation time, electron flux and ion trapping parameters for this broad energy range. The results obtained show that the rate of ECD is higher for more energetic (>1 eV) electrons. Long electron irradiation time with energetic electrons reduces average fragment ion mass and decreases efficiency of formation of c- and z-type ions. The obtained dependencies suggest that the average fragment ion mass and the ECD efficiency are functions of the total fluence of the electron beam (electron energy multiplied by irradiation time). The measured electron energy distributions in low-energy ECD and hot ECD regimes are about 1 eV at full width half maximum in employed experimental configurations.     

Precise and fast secondary ion mass spectrometry depth profiling of polymer materials with large Ar cluster ion beams

We demonstrate depth profiling of polymer materials by using large argon (Ar) cluster ion beams. In general, depth profiling with secondary ion mass spectrometry (SIMS) presents serious problems in organic materials, because the primary keV atomic ion beams often damage them and the molecular ion yields decrease with increasing incident ion fluence. Recently, we have found reduced damage of organic materials during sputtering with large gas cluster ions, and reported on the unique secondary ion emission of organic materials. Secondary ions from the polymer films were measured with a linear type time‐of‐flight (TOF) technique; the films were also etched with large Ar cluster ion beams. The mean cluster size of the primary ion beams was Ar₇₀₀ and incident energy was 5.5 keV. Although the primary ion fluence exceeded the static SIMS limit, the molecular ion intensities from the polymer films remained constant, indicating that irradiation with large Ar cluster ion beams rarely leads to damage accumulation on the surface of the films, and this characteristic is excellently suitable for SIMS depth profiling of organic materials. Copyright © 2009 John Wiley & Sons, Ltd.     

Facile synthesis of ZnO/CuO/Eu heterostructure photocatalyst for the degradation of industrial effluent

Zinc oxide-based ternary heterostructure ZnO/CuO/Eu(1%, 3%, and 5% of Eu) nanoparticles were effectively produced by employing Vigna unguiculata (cowpea)waste skin extract as fuel in a simple one-pot combustion process. The as-synthesized heterostructure was analyzed by X-ray diffraction studies, ultraviolet-visible spectroscopy, Fourier Transform Infrared Spectroscopy, Field Emission Scanning Electron Microscopy, and High-Resolution Transmission Electron Microscopy techniques. Besides, the photocatalytic degradation efficiency of the as-obtained ternary nanocomposite was evaluated under UV light for the degradation of model organic pollutants including methylene blue (MB), Rhodamine-B (RB), and an effluent sample collected from the textile industrial waste. During this study, the effect of a variety of parameters on the photodegradation activity of the photocatalysts has been thoroughly evaluated, such as light source, catalyst dose, irradiation period, dye concentration, solution pH, etc. Under UV irradiation(100 mins), the ternary ZnO/CuO/Eu photocatalyst demonstrated excellent degradation activity of ～99 and ～93% for MB and RB, respectively, while for the industrial effluent, a decent degradation activity of 42% has been recorded. Further experiments have revealed a pH and concentration-dependent photocatalytic behavior of the heterostructure photocatalyst. Therefore, the results suggest that the heterostructure photocatalyst can be potentially applied for wastewater treatment and other environmental applications.     

Effect of annealing on hydrophobic stability of plasma deposited fluoropolymer coatings

Fluorinated amorphous carbon (a-C:F) films e.g. plasma polymerised perfluorocyclobutane have long attracted much consideration due to their low surface energy, hydrophobicity, low refractive index, good electrical and thermal insulation and good thermal stability. Although a-C:F films have many advantages, hydrophobic stability over time in air and water remains a major concern. In this study, the effects of weathering conditions on the hydrophobicity of fluorocarbon films prepared from perfluorocyclobutane precursors were examined using water contact angle measurements. It was found that the high initial hydrophobicity of as-deposited films degrades rapidly in humid conditions. The stability of hydrophobicity can be significantly improved when a suitable treatment such as annealing is employed. The mechanism of weathering was explained with the help of a number of morphological and chemical characterisation techniques such as Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS). In particular, XPS results demonstrated that a reduction in the overall amount of -CF₃ radical, oxygenation of surface fluorides and the formation of an overlayer all influence the degradation of fluorocarbon in aquatic environment.     

Peptide structural analysis using continuous Ar cluster and C60 ion beams

A novel application of time-of-flight secondary ion mass spectrometry (ToF-SIMS) with continuous Ar cluster beams to peptide analysis was investigated. In order to evaluate peptide structures, it is necessary to detect fragment ions related to multiple neighbouring amino acid residues. It is, however, difficult to detect these using conventional ToF-SIMS primary ion beams such as Bi cluster beams. Recently, C₆₀ and Ar cluster ion beams have been introduced to ToF-SIMS as primary ion beams and are expected to generate larger secondary ions than conventional ones. In this study, two sets of model peptides have been studied: (des-Tyr)-Leu-enkephalin and (des-Tyr)-Met-enkephalin (molecular weights are approximately 400 Da), and [Asn¹ Val⁵]-angiotensin II and [Val⁵]-angiotensin I (molecular weights are approximately 1,000 Da) in order to evaluate the usefulness of the large cluster ion beams for peptide structural analysis. As a result, by using the Ar cluster beams, peptide molecular ions and large fragment ions, which are not easily detected using conventional ToF-SIMS primary ion beams such as Bi₃ ⁺, are clearly detected. Since the large fragment ions indicating amino acid sequences of the peptides are detected by the large cluster beams, it is suggested that the Ar cluster and C₆₀ ion beams are useful for peptide structural analysis.     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 1. Effect of main chain and pendant methyl groups

Polyatomic primary ions have been applied recently to the depth profiling of organic materials by secondary ion mass spectrometry (SIMS). Polyatomic primary ions offer low penetration depth and high damage removal rates in some polymers, but the relationship between polymer chemistry and degradation under polyatomic primary ion bombardment has not been studied systematically. In this study, positive and negative ion time‐of‐flight SIMS (ToF‐SIMS) was used to measure the damage of ～100 nm thick spin‐cast poly(methyl methacrylate) (PMMA), poly(methyl acrylate) (PMA) and poly(methacrylic acid) (PMAA), films under extended (～2 × 10¹⁴ ions cm^?2) 5 keV SF₅⁺ bombardment. These polymers were compared to determine the effect of the main chain and pendant methyl groups on their degradation under SF₅⁺ bombardment. The sputter rate of PMMA was approximately twice that of PMA or PMAA and the rate of damage accumulation was higher for PMA and PMAA than PMMA, suggesting that the main chain and pendant methyl groups played an important role in the degradation of these polymers under SF₅⁺ bombardment. These results are consistent with the literature on the thermal and radiation‐induced degradation of these polymers, which show that removal of the main chain or pendant methyl groups reduces the rate of depolymerization and increases the rate of intra‐ or intermolecular cross‐linking. Copyright © 2004 John Wiley & Sons, Ltd.     

Surface Study of Polymers by Static Secondary Ion Mass Spectrometry Using a Magnetic-Sector Mass Spectrometer

Results from static SIMS analysis of six thermoplastic polymers — polytetrafluoroethylene (PTFE), polyethylene (PE), polymethyl methacrylate (PMMA), polyethylene terephthalate (PET), polystyrene (PS) and polycarbonate (PC) — using a magnetic-sector SIMS instrument and O₂⁺ primary beam are presented. For PTFE as a representative sample, the charging effect is reduced only with a metal grid when analyzing positive secondary ions. When negative secondary ions are analyzed, excessive charges are self-compensated with a normal-incidence electron gun. Positive-ion spectra collected agree with spectra obtained using either a quadrupole or time-of-flight SIMS instrument and noble-gas ion beams. The agreement is objectively demonstrated by means of the capability to compare spectra in the NIST/EPA/MSDC mass spectral database. The merits of the use of high-mass resolution, of which magnetic-sector SIMS is inherently capable, to provide analytical information about the molecular species native to the sample are demonstrated in distinguishing three ambiguous peaks with nominal mass ratios m/z = 27, 39 and 59 from PMMA.     

Synthesis and Self-Assembly of 2nd Generation Dendritic Homopolymers and Copolymers of Polydienes with Different Isomeric Microstructures

Synthesis of 2^nd generation dendritic polymeric materials via anionic polymerization procedures in combination with chlorosilane chemistry, consisting either from one polydienic segment (homopolymers) or from two chemically different polydienic components (copolymers), is described. The polydienes used were poly(butadiene) (PB) with ∼90% 1,4-isomerism and poly(isoprene) (PI) with increased 3,4-isomerism (∼60%). Molecular characterization of intermediate products and the final dendritic materials was made with Gel Permeation Chromatography (GPC), Membrane and Vapour Pressure Osmometry (MO and VPO respectively), Gas Chromatography –Mass Spectroscopy (GC-MS) and ¹H-Nuclear Magnetic Resonance (¹H-NMR) Spectroscopy, leading to the conclusion that they can be considered model polymers. Morphological studies solely with Transmission Electron Microscopy (TEM) have been conducted on two of the four synthesized copolymer samples exhibiting microphase separation between the two polydiene segments.     

Medium energy,heavy and inert ion irradiation of metallic thin films: studies of surface nano‐structuring and metal burrowing

In context to the ion induced surface nanostructuring of metals and their burrowing in the substrates, we report the influence of Xe and Kr ion‐irradiation on Pt:Si and Ag:Si thin films of ~5‐nm thickness. For the irradiation of thin films, several ion energies (275 and 350 keV of Kr; 450 and 700 keV of Xe) were chosen to maintain a constant ratio of the nuclear energy loss to the electronic energy loss (S_n/S_e) in Pt and Ag films (five in present studies). The ion‐fluence was varied from 1.0 × 10¹⁵ to 1.0 × 10¹⁷ ions/cm². The irradiated films were characterized using Rutherford backscattering spectroscopy (RBS), atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM and SEM images show ion beam induced systematic surface nano‐structuring of thin films. The surface nano‐structures evolve with the ion fluence. The RBS spectra show fluence dependent burrowing of Pt and Ag in Si upon the irradiation of both ion beams. At highest fluence, the depth of metal burrowing in Si for all irradiation conditions remains almost constant confirming the synergistic effect of energy losses by the ion beams. The RBS analysis also shows quite large sputtering of thin films bombarded with ion beams. The sputtering yield varied from 54% to 62% by irradiating the thin films with Xe and Kr ions of chosen energies at highest ion fluence. In the paper, we present the experimental results and discuss the ion induced surface nano‐structuring of Pt and Ag and their burrowing in Si. Copyright © 2016 John Wiley & Sons, Ltd.     

Characterization and cytotoxicity and antihuman renal cell carcinoma potentials of starch capped-copper oxide nanoparticles synthesized by ultrasonic irradiation: Introducing a novel chemotherapeutic drug

In this research article we have demonstrated the sustainable green synthesis of a novel starch templated CuO NP following a clean and non-hazardous pathway. Ultrasonic irradiation was used to promote the reaction in alkaline medium. The numerous hydroxyl groups present in starch was exploited in the green reduction of immobilized copper ions in situ. They also helped to stabilize the as synthesized Cu NPs by encapsulation or capping. The morphology and physicochemical characteristics were ascertained over an array of analytical techniques like Scanning Electron Microscopy (SEM), Energy-Dispersive X-ray Spectroscopy (EDS), Elemental Mapping, Transmission Electron Microscopy (TEM), X-ray Diffraction (XRD), and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES). Biologically, the nanocomposite exhibited excellent cytotoxicity against human renal cell carcinoma (RCC-GH, CaKi-2 and HEK293) cell lines without affecting the normal (HUVEC) cell line. IC₅₀ values of the nanocomposite were found at 139, 208and 125 against RCC-GH, CaKi-2 and HEK293 cell lines respectively and accordingly, HEK293 afforded the best adenocarcinoma activity.     

Ionic impurity control by a photopolymerisation process of reactive mesogen

Extremely low ion density, 10^?8?10^?11 molar fraction, which inevitably exists due to residual ion impurities even in a purified liquid crystal (LC) compound, can significantly influence the electro-optic response in LC devices. We found that the density of ionic molecules increased with the addition of various dopants including triphenylphosphine oxide (TPPO), molecules with the functional group of aldehyde, epoxide and so on into a nematic LC cell by observing the electrical response of the LC cells and that the irradiation of ultraviolet (UV) light accelerated the generation of ionic molecules, indicating degradation of organic materials. However, the addition of reactive mesogen (RM) compounds to the LC mixture significantly decreased the effective density of ions during and after the photopolymerisation process. The cured RM networks effectively captured the ion impurities during the photopolymerising process and their ion capturing ability was sustained even after completing the photopolymerisation process. This observation may provide a simple and useful way to control the effective ion density in a liquid medium down to extremely low levels.     

Synthesis and Charcterzation of SilicaImmobilized Benzene-Diazo-Dmino-Azobenzene

Chelating groups can be chemically bonded to the surface of solid supports such as silica.Immobilization reations on silica are relatively simple, especially when compared to immobilization involving organic polymers. Because silica exhibits the good mechanical strength,swelling stability and the fast metal ion exchange kinetics, such materials are gaining increasing importance for the separation and enrichment of trace metal ions from dilute aqueous solution.     

Enhancement of cyanide photocatalytic degradation using sol–gel ZnO sensitized with cobalt phthalocyanine

In this work, the photodegradation of cyanide in aqueous suspension was used to determine the photocatalytic activity of sol–gel prepared ZnO which was impregnated with the Co (II) phthalocyanine (CoPc), as sensitizer. The prepared catalyst was characterized by Scanning Electron Microscopy (SEM) with Energy Dispersed Spectroscopy (EDS) detector, X-Ray Diffraction (XRD), Fourier Transform Infrared spectroscopy (FT-IR) and Diffuse UV–Vis Reflectance spectroscopy. Specific surface area was calculated from nitrogen adsorption isotherm using BET method. Compared with commercial ZnO and TiO₂ Degussa P25 photocatalysts, the sol–gel prepared ZnO catalyst sensitized with cobalt phthalocyanine showed the highest activities for degradation of cyanide in aqueous solution under visible light irradiation.     

Pyrolysis mass spectrometry of terephthalate polyesters using negative ionization

The usual method of studying thermal degradation mechanisms of polymers in vacuo is to use electron ionization pyrolysis mass spectrometry. This can lead to mass spectral fragmentation from the 70 eV electrons used. Low energy electrons (10–15 eV) produce a low abundance of positive ions. However, if a molecule is prone to capture a thermal energy electron, then negative ions are produced in high abundance. This report describes the negative ion pyrolysis mass spectrometry of polyethylene terephthalate and polybutylene terephthalate.     

Spectroscopic and electrical studies for the influence of ion beam and X-ray irradiation on poly-2-(N-propenamido-2-methylpropanesulfonic acid) and its polymer complex with cobalt chloride

The influence of argon ion beam and X-ray irradiations on poly-2-(N-propenamido-2-methylpropanesulfonic acid) (PPMPS) and its polymer complex with Co (II), (PPMPS-Co (II)), were studied using IR, UV/visible and d.c. electrical conductivity. After irradiation the polymer changed in color and become less soluble. The IR spectrum of irradiated PPMPS shows broadened bands at 3400 and 3550 cm^-1 which are assigned to stretch bands of NH and OH, respectively, as a consequence of intramolecular cyclization. Furthermore, a comparison of IR and UV/visible spectra of irradiated and non-irradiated PPMPS-Co(II), reveals that the main effect of irradiation was the degradation effect. Measurements of d.c. electrical conductivity for irradiated and non-irradiated polymers showed an increase of conductivity for the coordinated polymers compared to PPMPS. A relatively higher resistivity for the ion beam irradiated polymers and lower resistivity in case of X-ray irradiation have been observed. The increases of conductivity for the coordinated polymers compared to PPMPS were explained by the changes in glass transition temperatures (T_g) and activation energies for the different polymers.     

Strategy for Applying Microanalytical Techniques

A combination of microanalysis techniques is used to reveal with great precision the composition and microstructure of typical features in engineering materials. In this paper small particles, very thin films, interfaces and their contiguous region are considered. Small silicon nitride particles in an iron matrix produced by nitriding are characterized quantitatively with High Resolution Electron Microscopy (HREM) and Electron Probe Micro Analysis (EPMA) using Wavelength Dispersive X-ray Spectrometry (WDS). Thin aluminium-oxide films grown on aluminium substrates by thermal oxidation at low pressure are investigated with HREM and X-ray Photoelectron Spectroscopy (XPS). Their thickness, composition and degree of crystallinity are established as a function of oxidation temperature and time. At and near the oxide-layer/MCrAlY-coating (M=Ni and/or Co) interface the aluminium and chromium depletion behaviour of the coating material due to high-temperature oxidation is studied with high-resolution Scanning Electron Microscopy (SEM), EPMA and Auger electron spectroscopy (AES). The composition-depth profiles obtained for the coating material are used to determine the composition dependent diffusion coefficients. These properties are crucial for the prediction through computational modelling of the coating material oxidation behaviour and enable the development of new coating materials.     

Scintillation of Sol–Gel Derived Lutetium Orthoborate Doped with Ce3+ Ions

Ce^{3 +}-doped LuBO₃ powders have been prepared by a sol–gel process with Ce^{3 +} concentration varying between 0 and 5 mol%. These materials have been analyzed by X-ray Diffraction and Fourier Transform Infra Red Spectroscopy. The results confirm that all the materials have the vaterite type even if the calcination has been performed at 800°C. Furthermore, doping with Ce^{3 +} ions does not affect the structure and the vaterite is preserved even at 5% doping. Scanning Electron Microscopy showed a very uniform morphology with small spherical grains with a narrow size distribution. Optical properties have been studied to confirm the effective substitution of Ce^{3 +} for Lu^{3 +} ions and to determine the materials scintillation performances. It has been shown that 0.5% is the optimum Ce(III) concentration in term of scintillation yield with an X-ray conversion yield equivalent to that of standard BGO (Bi₄Ge₃O₁₂). The afterglow has also been measured and confirms the potential of these materials as scintillators.