Preparation of PAMAM- and PPI-metal (silver, platinum, and palladium) nanocomposites and their catalytic activities for reduction of 4-nitrophenol

Dendrimer-metal (silver, platinum, and palladium) nanocomposites are prepared in aqueous solutions containing poly(amidoamine) (PAMAM) dendrimers with surface amino groups (generations 3, 4, and 5) or poly(propyleneimine) (PPI) dendrimers with surface amino groups (generations 2, 3, and 4). The particle sizes of the metal nanoparticles obtained are almost independent of the generation as well as the concentration of the dendrimer for both the PAMAM and the PPI dendrimers; the average sizes of silver, platinum, and palladium nanoparticles are 5.6-7.5, 1.2-1.6, and 1.6-2.0 nm, respectively. It is suggested that the dendrimer-metal nanocomposites are formed by adsorbing the dendrimers on the metal nanoparticles. Studies of the reduction reaction of 4-nitrophenol by these nanocomposites show that the rate constants are very similar between PAMAM and PPI dendrimer-silver nanocomposites, whereas the rate constants for the PPI dendrimer-platinum and -palladium nanocomposites are greater than those for the corresponding PAMAM dendrimer nanocomposites. In addition, it is found that the rate constants for the reduction of 4-nitrophenol involving all the dendrimer-metal nanocomposites decrease with an increase in the dendrimer concentrations, and the catalytic activity of dendrimer-palladium nanocomposites is highest.     

Comparison of PAMAM-Au and PPI-Au nanocomposites and their catalytic activity for reduction of 4-nitrophenol

Dendrimer-Au nanocomposites are prepared in aqueous solutions using poly(amidoammine)dendrimers (PAMAM) (generation 2, 3, and 5) and poly(propyleneimine)dendrimers (PPI)(generation 2, 3, and 4) by wet chemical NaBH(4) method. The Au nanoparticles thus obtained are 2-4 nm in diameter for both dendrimers and no generation dependence on the particle size is observed, whereas the generations of the dendrimers are increased as stabilization of Au-nanoparticles is achieved with lower dendrimer concentrations. Studies of the reduction reaction of 4-nitrophenol using these nanocomposites show that the rate constants for the PAMAM dendrimers (generations 2 and 3) are higher than those for the PPI dendrimers (generations 2 and 3), while a distinct difference in the rate constants is not seen for the PAMAM dendrimer (generation 5) or the PPI dendrimer (generation 4). In addition, the rate constants for the reduction of 4-nitrophenol involving all the dendrimers decrease with increases in dendrimer concentrations.     

磁性Fe_3O_4@PS@PAMAM-Ag复合催化粒子的制备及其可再生催化性能(英文)

采用聚苯乙烯(PS)包裹Fe3O4磁性纳米粒子,制得Fe3O4@PS复合微球,以此作为磁性载体,通过微球表面的羧基将聚酰胺-胺类树形大分子(PAMAM)连接到磁性载体上,然后使Ag纳米粒子镶嵌在树形分子层中,制得可再生的金属复合催化粒子Fe3O4@PS@PAMAM-Ag.并采用红外光谱、扫描电镜、电感耦合等离子体质谱(ICP-MS)和X射线光电子能谱等方法对复合催化粒子进行了表征,结果表明,树形分子可以较好地分散和稳定金属Ag纳米粒子,所制复合催化粒子表面Ag含量为1.64%,具有较高的催化还原对硝基苯酚的活性.同时,利用外加磁场可以方便快捷地从反应体系中分离出来,继续用于下一次反应中,复合催化粒子循环使用6次后,仍保持完全的催化性能.     

Morphological change of gold-dendrimer nanocomposites by laser irradiation

Gold-dendrimer nanocomposites are prepared in aqueous solutions in the presence of poly(amidoamine)dendrimers (PAMAM) (generation 3 and 5) or poly(propyleneimine)dendrimers (PPI) (generation 3 and 4) by wet chemical NaBH(4) method. Thus prepared gold-dendrimer nanocomposites are irradiated by laser at 532 nm. UV-vis absorption spectroscopy and transmission electron microscopy reveal that the gold nanoparticles grow with the laser irradiation time as well as the fluence of the laser; in particular, the gold nanoparticles prepared at lower concentrations of PAMAM dendrimer as well as lower generations of PAMAM grow significantly. On the other hand, in the case of PPI dendrimers, the gold nanoparticles hardly grow by irradiation. In addition, dynamic light-scattering measurements show that the laser irradiation markedly promotes the association of the gold-PAMAM G3 dendrimer nanocomposites compared to that of the gold-PAMAM G5 dendrimer nanocomposites, while the sizes of association for the gold-PPI G3, G4 dendrimer nanocomposites hardly change by laser irradiation.     

Scavenging DPPH radicals catalyzed by binary noble metal-dendrimer nanocomposites

Catalytic activity of gold-platinum, gold-palladium, and platinum-palladium dendrimer nanocomposites for scavenging 1,1-diphenyl-2-picrylhydrazyl (DPPH) radicals was investigated. The gold-platinum and gold-palladium dendrimer nanocomposites were prepared via simultaneous reduction by sodium borohydride in the presence of poly(amidoamine) (PAMAM) dendrimers with amine or carboxyl terminal groups. The particles were not mixtures of monometallic particles but alloyed bimetallic particles. Bimetallic particles exhibited higher catalytic activity than monometallic ones.     

PAMAM树形分子与Cd2＋的配位作用研究及CdS/PAMAM纳米复合材料的制备与表征

CdS半导体纳米簇具有独特的光、电性能, 如何制备均匀分散的、能够稳定存在的CdS纳米簇是目前的研究热点之一. 以聚酰胺-胺(PAMAM)树形分子为模板, 原位合成了CdS纳米簇. 首先用UV-Vis分光光度法研究了与树形分子的配位机理, 得出G4.5和G5.0的平均饱和配位数分别为16和34, 并发现在G4.5PAMAM树形分子中Cd^2＋主要与最外层叔胺基配位, 在G5.0PAMAM树形分子中Cd^2＋主要与最外层伯胺基配位. 酯端基的G4.5的模板作用要明显优于胺端基的G5.0. 通过改变Cd^2＋与G4.5树形分子的摩尔比可以得到不同粒径的CdS纳米簇. 溶液的pH值对CdS纳米簇影响很大, pH在7.0左右制备的CdS纳米簇粒径小而均匀, 且溶液稳定性高. 用UV-Vis分光光度计和TEM对CdS纳米簇的大小和形貌进行了表征. 结果表明TEM观测CdS纳米簇的粒径要大于用Brus公式的估算值.     

以聚酰胺-胺树形分子为模板制备AgI纳米簇

本文以聚酰胺-胺(PAMAM)树形分子为模板,原位制备AgI纳米簇.系统地研究了AgI纳米簇制备过程中各种反应条件如树形分子端基、反应时间、Ag⁺与PAMAM摩尔比等对AgI纳米簇粒径的影响,分别用紫外-可见光谱、荧光光谱、透射电镜等对所制备的纳米簇进行表征.在相同的条件下,以G4.5-COOH₃为模板较以G5.0-NH₂为模板制备的AgI纳米簇粒径小、分布均匀,这主要取决于G4.5-COOCH₃PAMAM树形分子所起的“内模板”作用.G4.5-COOH₃树形分子浓度为1×10^-5mol/L,Ag⁺与树形分子摩尔比为30:1时所制备的AgI纳米簇的粒径分布均匀、稳定性好,室温避光可稳定存在两个月以上.     

Kinetic and particle size studies of emulsion polymerization of methyl methacrylate and styrene with using polyamidoamine dendrimer as seed

The emulsion polymerization of methyl methacrylate (MMA) and styrene (St) were investigated with using polyamidoamine (PAMAM) dendrimer as seed, potassium persulfate as initiator and sodium dodecyl sulfate as emulsifier. The effects of 4.0GPAMAM dendrimer concentration, initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature on the monomer conversion and polymerization rate were investigated. At the same time, the influence of the generation of PAMAM dendrimer on latex particle size was studied also. The results showed that the monomer conversion and polymerization rate increased with increasing initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature. But polymerization rate increased firstly with an increase in the 4.0GPAMAM dendrimer from 0.03 g to 0.09 g and then decreased with further increase to 0.12 g. When the concentration of 4.0GPAMAM dendrimer less than 1.449 × 10^?4 mol/L, the kinetic equation can be expressed by Rp∝[4.0GPAMAM]^0.772[SDS]^0.562[KPS]^0.589[M]^0.697, and the activation energy (Ea) of emulsion polymerization is 62.56kJ/mol. In additional, the copolymer latex particle size decreased and possessed monodispersity with increasing the generation of PAMAM dendrimer. According to FT-IR spectrum analysis, PAMAM dendrimer is successfully incorporated into the poly(PAMAM-St–MMA) latex particles.     

PAMAM树形分子为模板低温制备纳米硫化锌空心球

Hollow ZnS spheres have been prepared in the presence of generation 3.5 poly (amidoamine) dendrimers with surface ester groups (G3.5-COOCH3 PAMAM dendrimer) as synthetic matrix template. The products obtained were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV-Vis absorption. TEM studies show that the hollow spheres with diameters ranging from 80 to 100 nm are prepared. The range of wall thickness was estimated to be about 20～30 nm. It was found that the concentration of PAMAM dendrimer had a significant influence on the formation of hollow ZnS spheres. The possible formation mechanism of the hollow spherical structure is also discussed.     

PAMAM dendrimer interactions with supported lipid bilayers: a kinetic and mechanistic investigation

The interaction kinetics of polyamidoamine (PAMAM) dendrimers with supported lipid bilayers of 1,2-sn-glycero-dimyristoylphosphocholine prepared by the vesicle deposition has been probed by optical waveguide lightmode spectroscopy and atomic force microscopy (AFM). In particular, the influence of PAMAM dendrimer generation (G2, G4, and G6) and concentration (1 to 100 nM) on the levels of adsorption and lipid bilayer removal have been determined as a function of time; hence interaction kinetics and mechanisms have been further elucidated. Dendrimer interaction kinetics with the lipid bilayer are concentration dependent in a complex manner, with net bilayer removal at 1 and 100 nM and net adsorption at 10 nM; these effects are irrespective of dendrimer generation. The pseudo first order rate constant for bilayer removal (at 1 and 100 nM) follows the order G6 > G4 > G2. In contrast, the pseudo first order rate constant for adsorption at 10 nM follows the order G2 > G4 > G6. AFM has confirmed expansion of lipid bilayer defects, hole formation, and adsorption to the bilayer or bilayer defects, and their concentration and generation dependence. These findings have implications when designing dendrimers for specific biopharmaceutical activities, e.g., as drugs, drug delivery vehicles, transfection agents, or antimicrobials.     

Structural analysis of poly(amidoamine) dendrimer immobilized in crosslinked poly(ethylene glycol)

Polymeric membranes comprised of poly(amidoamine) (PAMAM) dendrimer immobilized in a poly(ethylene glycol) (PEG) network exhibit an excellent CO₂ separation selectivity over H₂. The CO₂ permeability increases with PAMAM dendrimer concentration in the polymeric membrane and becomes 500 times greater than H₂ permeability when the dendrimer content was 50 wt % at ambient conditions (5 kPa of CO₂ partial pressure). However, the detailed morphology of the membrane has not been discussed. The immiscibility of PAMAM dendrimer and PEG matrix results in phase separation, which takes place in a couple of microns scale. Especially, laser scanning confocal microscope captures a 3D morphology of the polymeric blend. The obtained 3D reconstructions demonstrate a bicontinuous structure of PAMAM dendrimer‐rich and PEG‐rich phases, which indicates the presence of PAMAM dendrimer channel penetrating the polymeric membrane, and CO₂ will preferentially pass through the dendrimer channel. In addition, Fourier transform of the 3D reconstructions indicates the presence of a periodic structure. An average size of the dendrimer domain calculated is 2–4 μm in proportion to PAMAM dendrimer concentration. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

低代端酯基PAMAM树形分子存在下银纳米颗粒的制备

在低代端酯基PAMAM树形分子(G1.5-COOCH₃)存在时，用氢气还原AgNO₃制备出银纳米颗粒。用透射电子显微镜(TEM)，电子衍射(ED)，紫外-可见吸收光谱(UV-Vis)和红外光谱(FT-IR)对所制备的银纳米颗粒进行了表征。实验结果表明，当用氢气作为还原剂时，以低代树形分子为保护剂，通过优化还原条件，可成功制备尺寸稳定、均一的银纳米颗粒，其粒径为2.9±0.5 nm，且所制备的银纳米颗粒的粒径分布较窄。根据树形分子的理论尺寸与制备的银纳米颗粒的粒径关系，可推断出大多数的银纳米颗粒是由多个树形分子所包围而稳定存在。     

Synthesis of polyamidoamine dendrimer (PAMAM/CuS/AA) nanocomposite and its application in the removal of Isma acid fast yellow G Dye

The adsorption of Isma acid fast yellow G dye was studied using polyamidoamine (PAMAM)/Copper sulfide (CuS)/AA nanocomposite containing different amounts of CuS by batch technique. PAMAM dendrimer/CuS/AA nanocomposites were synthesized via gamma irradiation cross‐linking method with the aid of sonication. The nanocomposites were characterized by Fourier‐transform infrared, X‐ray diffraction, transmission electron microscope, energy dispersive spectroscopy X‐ray, thermal gravimetric analysis, ultraviolet‐visible, and fluorescence spectroscopy. The size of the CuS nanoparticles was formed in the range of 12–19 nm. The adsorption capacity of the nanocomposites was evaluated as a function of initial dye concentration, pH, adsorbent dosage, and time. It was verified that the adsorption rate fits a pseudo‐second‐order kinetics for initial Isma acid fast yellow G dye concentrations. Results indicated that the adsorption of Isma acid fast yellow G dye fitted well to the Langmuir model. Our results demonstrate that the PAMAM dendrimer/CuS/AA nanocomposite is very promising for removing organic dyes from wastewater. Copyright © 2015 John Wiley & Sons, Ltd.     

Polyamidoamine dendrimer and dextran conjugates: preparation,characterization, and in vitro and in vivo evaluation

Amide and ester conjugates of aceclofenac with polyamidoamine (PAMAM-G0) dendrimer zero generation and dextran (40 kDa) polymeric carrier, respectively, are presented. The prepared conjugates were characterized by UV, TLC, HPLC, IR, and ¹H NMR spectroscopy. The average degrees of substitution of amide and ester conjugates were determined and found to be (12.5 ± 0.24) % and (7.5 ± 0.25) %, respectively. The in vitro hydrolysis studies showed that dextran ester conjugate hydrolyzed faster in a phosphate buffer solution of pH 9.0 as compared to PAMAM dendrimer G0 amide conjugate, and followed the first order kinetics. No amount of the drug was regenerated at pH 1.2 in simulated gastric fluid. The dextran conjugate showed short half-life as compared to the PAMAM dendrimer conjugate. Anti-inflammatory and analgesic activities of the dendrimer conjugate were found to be similar to those of the standard drug. Results of chronic ulceroginic activity showed deep ulceration and high ulcer index for aceclofenac, whereas lower ulcer index was found for the PAMAM dendrimer and dextran (40 kDa) conjugates. Experimental data suggest that PAMAM dendrimer and dextran (40 kDa) can be used as carriers for the sustained delivery of aceclofenac along with a remarkable reduction in gastrointestinal toxicity.     

Amphiphilic Dendrimer as Reverse Micelle: Synthesis,Characterization and Application as Homogeneous Organocatalyst

The core and surface terminal groups are the two main catalytic sites in a dendrimer. In most of the reported examples, the catalytic sites in dendritic catalysis are the surface terminal functional groups. This perspective article concerned with the dendrimer based catalysis, involving these two catalytic sites and the dendrimer cavities. The interior cavities provide the nanoscale reactor sites, by creating reverse micelle like appearance for catalysis. In exploring the significant achievements in this area, a low generation PAMAM dendrimer with amphiphilic nature, having a polymeric core with large number of pendent amino groups was synthesized and concentrated its catalytic activity. The key features with respect to positive and/or negative catalytic activity was highlighted by synthesizing various aryl and heteroaryl 2-substituted benzimidazoles. The synthesized dendritic organocatalyst was proved to be amazingly reactive and gave high yield of products within a few minutes at room temperature with low catalyst loading. Here, a new stable hemiaminal, the species rarely been detected and much less isolated in bulk, was obtained during the synthesis of benzimidazoles. Moreover, this is the first reported method for the synthesis of benzimidazoles, using the homogeneous PAMAM dendrimer as a basic organocatalyst.     

SiO2–poly(amidoamine) dendrimer inorganic/organic hybrids

SiO₂–poly(amidoamine) (PAMAM) dendrimer hybrids were synthesized via (1) a Michael addition reaction between the dendrimer and 3‐(trimethoxysilyl) propyl acrylate, (2) the dissolution of the formed compound in methanol, and (3) the mixing of the latter solution with a methanol solution of partly hydrolyzed tetraethylorthosilicate (TEOS) and its casting on a glass substrate. ¹H NMR indicated that in the first step, 77% of the secondary amines were converted into tertiary amines when the fourth‐generation dendrimer was employed and 46% were converted when the second‐generation dendrimer was used. The final SiO₂–PAMAM dendrimer hybrids were obtained via the hydrolysis and condensation of the compound obtained via the Michael addition and the methanol solution of partly hydrolyzed TEOS. The compartmentalized structure of the hybrids due to the compartments of the dendrimers could be controlled by changing the dendrimer and the amount of TEOS. Scanning electron microscopy and transmission electron microscopy micrographs provided information about the structure of the hybrids. Like the PAMAM dendrimer, the SiO₂–PAMAM dendrimer hybrids exhibited a high metal ion complexing capacity because of the presence of the compartments of the dendrimer; they can be, however, much more easily handled, and, as demonstrated by thermogravimetric experiments, have much higher thermal resistance. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1443–1449, 2000     

Specific binding structures of dendrimers on lipid bilayer membranes

Dissipative particle dynamics simulations are used to study the specific binding structures of polyamidoamine (PAMAM) dendrimers on amphiphilic membranes and the permeation mechanisms. Mutually consistent coarse-grained (CG) models both for PAMAM dendrimers and for dimyristoylphosphatidylcholine (DMPC) lipid molecules are constructed. The PAMAM CG model describes correctly the conformational behavior of the dendrimers, and the DMPC CG model can properly give the surface tension of the amphiphilic membrane. A series of systematic simulations is performed to investigate the binding structures of the dendrimers on membranes with varied length of the hydrophobic tails of amphiphiles. The permeability of dendrimers across membranes is enhanced upon increasing the dendrimer size (generation). The length of the hydrophobic tails of amphiphiles in turn affects the dendrimer conformation, as well as the binding structure of the dendrimer-membrane complexes. The negative curvature of the membrane formed in the dendrimer-membrane complexes is related to dendrimer concentration. Higher dendrimer concentration together with increased dendrimer generation is observed to enhance the permeability of dendrimers across the amphiphilic membranes.     

铁氰化钴/树状高分子修饰电极免标记法检测基因突变

利用铁氰化钴/树状高分子(CoHCF/PAMAM)复合材料修饰玻碳电极(GCE), 制备了免标记检测基因突变的新型DNA电化学传感器. 传感器中树状高分子层明显增加了单链DNA探针的固定量, 铁氰化钴层增大了鸟嘌呤的氧化信号, 该传感器可以灵敏识别单碱基错配的基因序列, 具有良好的选择性和灵敏度. 在7.6×10^-11～3.05×10^-8 mol/L浓度范围内, 鸟嘌呤(G)的氧化峰电流差值与突变基因浓度呈良好的线性关系, 检出限为1.0×10^-11 mol/L(S/N=3).     

Controlled interparticle spacing through self-assembly of Au nanoparticles and poly(amidoamine) dendrimers

Control of particle-particle spacing is a key determinant of optical, electronic, and magnetic properties of nanocomposite materials. We have used poly(amidoamine) (PAMAM) dendrimers to assemble carboxylic acid-functionalized mixed monolayer protected clusters (MMPCs) through acid/base chemistry between the particle and dendrimer. Small angle X-ray scattering was then used to establish average inter-MMPC distances. Five generations of PAMAM dendrimer (0, 1, 2, 4, 6) were investigated, with a monotonic increase in interparticle spacing from 4.1 to 6.1 nm observed with increasing generation.     

Effects of various thiol molecules added on morphology of dendrimer-gold nanocomposites

Interactions between poly(amidoamine) dendrimer (PAMAM)-gold nanocomposites and alkanethiols and between the former nanocomposites and thiol-modified poly(amidoamine) dendrons in ethyl acetate were investigated by adding alkanethiols, such as 1-propanethiol and 1,3-propanedithiol, and thiol-modified poly(amidoamine) dendrons, generations 0.5 and 2.5 (G0.5-SH and G2.5-SH). The PAMAM dendrimers with surface methyl ester groups used were generations 1.5 and 5.5 (G1.5 and G5.5). The mean particle sizes of PAMAM-gold nanocomposites were about 2.1 for G1.5 and 2.4 nm for G5.5. In both nanocomposite systems where 1-propanethiol and 1,3-propanedithiol were added, the mean particle size was about 4 nm, twice that of the systems where these thiols were not added. Increasing the addition of 1,3-propanedithiol made the average particle size smaller for both nanocomposites systems. To compare with alkanethiol, thiol-modified poly(amidoamine) dendron with a highly branched structure on one side was synthesized. Using G2.5-SH as a protective agent, dendron-gold nanocomposites with mean diameters of 3 to 4 nm were obtained. The difference in particle size was seen only when the combination of PAMAM-gold nanocomposites and thiol-modified dendron was less sterically dense, modified dendron (G0.5-SH). The mechanisms for morphology changes in the dendrimer-gold nanocomposites by the addition of these thiols are discussed.