Sampling and quantitation of lipids in aerosols from the remote marine atmosphere

A procedure is described for the determination of organic compounds in aerosols and rain from the remote marine atmosphere. Five classes of naturally occuring lipids (n-alkanes, was esters, fatty alcohols, sterols, and fatty acids) were quantified in the samples. Air samples (4000–10 000 m³) were collected on glass-fiber filters under authomatic control. Rain samples (1–5 l) were collected on an event basis. Filter and rain samples were extracted with dichloromethane and the extracts were fractionated into discrete chemical classes by adsorption chromatography with silica gel. The fractions were derivatized (if necessary) and quantified by high-resolution glass-capillary gas chromatography (HRGC) and HRGC/mass spectrometry. A second filter extraction was required for quantitation of fatty acid salts. On-column injection of the fractions provided identification and quantification of a wide range of homologs within each compound class: C₁₅–C₄₄ for n-alkanes, C₃₆–C₆₂ for was esters, and C₁₃–C₃₆ for fatty alcohols and fatty acids. Internal standards were used to quantify recoveries and concentratins. Mean recoveries relative to the internal standares were 96.5% for C₁₅–C₃₆ n-alkanes, 96.4% for C₂₀–C₃₀ n-fatty acids, 92.5% for C₁₄–C₃₀ n-fatty alcohols and 93.3% for cholesterol. The procedural blanks for the remote marine aerosol samples allow detection limits of 0.1–1.0 pg m^?3 for most compounds. These values are lower than any other method used at coastal marine, rural or suburban sampling locations.     

Separation of a Homologous Series of Long-Chain Fatty Alcohols (C49-C58) From Mycobacterium Tuberculosis H37Ra by High Performance Liquid Chromatography

Abstract

Fatty alcohols were obtained from the saponified chloro-form-methanol extract of Mycobacterium tuberculosis H37Ra by extraction with diethyl ether and partially purified by silicic acid column chromatography. The long-chain fatty alcohols (C₄₉-C₅₈) were separated from the shorter-chain alcohols by Sephadex LH-20 column chromatography and further fractionated into saturated and unsaturated alcohols by argentation thin-layer chromatography. These two fractions were analyzed by proton nuclear magnetic resonance spectro-scopy, derivatized to the 3,5-dinitrobenzoyl esters, and fractionated on a C₁₈-bonded silica column by high performance liquid chromatography (HPLC). Complete separation of esters differing by two carbon units and partial separation     

Glycosides of marine invertebrates. VIII. Steroid glycosides of the holothurianIsostichopus badionotus

The steroid glycoside fraction ofIsostichopus badionotus, consisting of a mixture of D-xylosides of steroid alcohols, has been isolated by column chromatography on silica gel. The mixture of aglycones obtained after acid hydrolysis was separated with the aid of argentation chromatography into several fractions. GLC-MS analysis, and also the use of IR and¹³C NMR spectroscopy has shown that the steroid glycosides ofI. badionotus are xylosides of Δ⁰-, Δ⁷-, Δ²²-, and Δ^7.22-, C₂₇-, C₂₈-, and C₂₉-steroids of the cholestane series.     

Distribution coefficients in the water-dodecane system and the heats of adsorption of C<Subscript>1</Subscript>-C<Subscript>8</Subscript> alcohols on silica

Distribution coefficients in the water-dodecane system and the heats of adsorption of C₁-C₈ alcohols on silica (Silochrom S-80) were determined by gas chromatography. At low temperatures, C₁-C₄ alcohols were largely distributed in the aqueous phase, and C₆-C₉ alcohols were predominantly dissolved in the organic phase; C₅ alcohols had intermediate properties. Permittivity was found to correlate with log K _d, which allowed us to predict the character of the distribution of alcohols in the water-oil system. The heats and isotherms of adsorption were determined for the alcohols studied. The heats of adsorption of alcohols on silica monotonically increased in the series under consideration. For C₅-C₈ alcohols, they exceeded the heat of adsorption of water. The isotherms of adsorption were described by the Freundlich equation.     

N-alkylpyridinium quaternization combined with liquid chromatography–electrospray ionization-tandem mass spectrometry: A highly sensitive method to quantify fatty alcohols in thyroid tissues

A highly sensitive method was developed for the identification and quantification of fatty alcohols in biological tissues. In the presence of pyridine-d₀ and triflic anhydride (Tf₂O), fatty alcohols were converted into permanently charged N-alkylpyridinium ions. Stable isotope-labeled derivatives were generated by pyridine-d₅ and added as internal standard (IS). The mixture was analyzed by liquid chromatography coupled to positive electrospray ionization tandem mass spectrometry (LC–ESI-MS/MS). This method was optimized and validated in terms of reaction time, derivatization efficiency, stability, desalting, and ion suppression effect. Besides, fatty alcohols exhibited good linear relationship (r² > 0.993) over the concentration range of 10 ng mL⁻¹–1 μg mL⁻¹. The limits of detection (LODs) were lowered from previously reported 0.1 ng mL⁻¹ to 0.25 pg mL⁻¹. Precision (RSD% < 15.6%), accuracy (93.0–107.2%), matrix effect, and recovery (in thyroid tissues) were validated as well. Finally, this method was applied for the analysis of ten even carbon-numbered fatty alcohols (C₈–C₂₄) in human thyroid carcinoma and para-carcinoma tissues, revealing a significant decrease of fatty alcohols (free and esterified) in thyroid carcinoma tissues (p < 0.05).     

Catalytic performance of Fe modified K/MO2C catalyst for CO hydrogenation

Fe modified and un-modified K/Mo2C were prepared and investigated as catalysts for CO hydrogenation reaction. Compared with K/Mo2C catalyst, the addition of Fe increased the production of alcohols, especially the C2+OH. Meanwhile, considerable amounts of C5+ hydrocar- bons and C2= -C4= were formed, whereas methane selectivity greatly decreased. Also, the activity and selectivity of the catalyst were readily affected by the reaction pressure and temperature employed. According to the XPS results, Mo4+ might be responsible for the production of alcohols, whereas the low valence state of Mo species such as Mo0 and/or Mo2+ might be account for the high activity and selectivity toward hydrocarbons.     

HPLC of fatty acid esters of mono- and polyhydric alcohols. Part 1: Analytical separation

This paper shows how simply and yet very rapidly fatty acid esters of monohydric alcohols, but particularly partial and full fatty acid esters of fully hydric alcohols can be separated and determined by means of high-pressure liquid chromatography on LiChrosorb RP-8 with methanol/water. We have separated quantitatively the methylesters of the fatty acids C_8:0 to C_22:0 and C_24:0, the i-propyl-, i-butyl-, n-hexyl- and i-octyl-esters of the even-numbered fatty acids C_8:0 to C_18:0, mono- and difatty acid esters of the 1,3-bis-(2-hydroxyethyl)-5,5-dimethyl-hydantoin, mono-, di- and triesters of the trimethylolpropane as well as the tetraesters of the penta-erythrite.     

First synthesis of (1,2-C2)-monolignol glucosides

The monolignol glucosides (1,2-¹³C₂)-p-glucocoumaryl alcohol, (1,2-¹³C₂)-coniferin and (1,2-¹³C₂)-syringin, and the glucosides of (1,2-¹³C₂)-p-coumaric, (1,2-¹³C₂)-ferulic and (1,2-¹³C₂)-sinapic acids were synthesized by condensation of the corresponding aldehydes with (1,2,3-¹³C₃)-malonic acid. The free acids were converted to the acyl chlorides prior to their reduction to alcohols.     

Synthesis of 4‐(7‐diethylaminocoumarin‐3‐yl)benzeneisocyanate (DACB‐NCO): A highly sensitive fluorescent derivatization reagent for alcohols in high‐performance liquid chromatography

4‐(7‐Diethylaminocoumarin‐3‐yl)benzeneisocyanate (DACB‐NCO) was synthesized as a new fluorescent derivatization reagent for alcohols for use in high‐performance liquid chromatography (hplc). Saturated alcohols (C₆‐C₂₂) were derivatized in good yields into the corresponding fluorescent DACB‐carbamic esters by treating with DACB‐NCO. The DACB‐carbamic esters of these alcohols were clearly separated on a reversed‐phase hplc column (Inertsil ODS‐2, mobile phase: methanol‐water, excitation wavelength 402 nm; emission wavelength 488 nm). The detection limit (S/N = 3) of cetyl alcohol, as a test compound, was 5 fmol/10 μl.     

Selective Ortho alkylation of phenol with alcohols over catalysts derived from hydrotalcite-like anionic clays

The vapour phase alkylation of phenol with a series of alcohols containing different number of carbons ranging from C₁ to C₈ were investigated over catalysts derived from magnesium-aluminium hydrotalcite with Mg/Al atomic ratio 3 (MgAl 3.0-HT). The results indicated that at 623 K the catalytic activity for phenol conversion increased with increasing chain length of linear long chain alcohols to give 2-alkylated linear alkyl phenols, without any isomerisation of the alkyl moiety. Isomorphous substitution of Mg²⁺ by Cu²⁺ or Ni²⁺ in the MgAl 3.0-HT resulted in an increase in selectivity of 2-alkyl and 2,6-dialkylphenols (≈60%) in the alkylation of phenol with 1-hexanol or 1-octanol.     

Repeller-Induced dissociation of alkyl alcohols in thermospray mass spectrometry

Six alkyl alcohols were studied using thermospray mass Spectrometry. Whereas the dominant ion in the spectrum up to a repeller potential of 120 V was [M + NH₄]⁺, above that potential [M + H]⁺ and fragment ions appeared. The fragments observed were largely due to hydrogen release from alkyl ions ([C_nH_2n+1]⁺ – H2 → [C_nH_2n-1]⁺) and loss of water or some other stable molecule from the same species. The results are compared with those from ionization of the same alcohols under electron impact and photoionization conditions and with results obtained for methanol under thermospray conditions.     

Catalytic Ethanolysis of Kraft Lignin into High‐Value Small‐Molecular Chemicals over a Nanostructured α‐Molybdenum Carbide Catalyst

We report the complete ethanolysis of Kraft lignin over an α‐MoC_1?x/AC catalyst in pure ethanol at 280 °C to give high‐value chemicals of low molecular weight with a maximum overall yield of the 25 most abundant liquid products (LP25) of 1.64 g per gram of lignin. The LP25 products consisted of C₆–C₁₀ esters, alcohols, arenes, phenols, and benzyl alcohols with an overall heating value of 36.5 MJ kg^?1. C₆ alcohols and C₈ esters predominated and accounted for 82 wt % of the LP25 products. No oligomers or char were formed in the process. With our catalyst, ethanol is the only effective solvent for the reaction. Supercritical ethanol on its own degrades Kraft lignin into a mixture of small molecules and molecular fragments of intermediate size with molecular weights in the range 700–1400, differing in steps of 58 units, which is the weight of the branched‐chain linkage C₃H₆O in lignin. Hydrogen was found to have a negative effect on the formation of the low‐molecular‐weight products.     

Reactions of [CH3]+ and [CD3]+ with alcohols

The reactions of [CH₃]⁺ and [CD₃]⁺ with a number of C₁ to C₅ alcohols were studied at approximately thermal energies (0.1 eV) using a tandem Dempster ion cyclotron resonance mass spectrometer. Branching ratios obtained under single collision conditions are reported for [CH₃]⁺ and [CD₃]⁺ with methanol, perdeutero methanol, ethanol, allyl alcohol, 1-propanol, 2-propanol, perdeutero-2-propanol, 1-butanol, 2-butanol, t-butanol, cyclopentanol and 1-pentanol. The results are examined in terms of the mechanism of reactions and indicate that upon progression to larger alcohols, the formation of a long-lived adduct becomes less important in determining the reaction products.     

Analysis of high molecular weight esters and ketones in thymus

A crystalline mixture of esters from Thymus chamaedris is analyzed by mass spectrometry, and after hydrolysis, by gas chromatography. Two series of straight chain even aliphatic acids from C₁₆ to C₂₆, and from C₄₀ to C₄₈, and a series of straight chain even saturated primary alcohols, from C₈ to C₃₀, are its main constituents. Another crystalline mixture, isolated from Thymus caespititius, is shown by mass spectrometry and gas chromatography to be composed of a straight chain series of aliphatic ketones, from C₂₅ to C₃₇.     

Thin-Layer Chromatography of Bile Alcohols,Bile Acids and Conjugated Bile Acids

Abstract

Thin-layer chromatography of bile alcohols, bile acids and bile acid conjugates has been reviewed. Particular emphasis has been placed on the separation of the glycine and taurine conjugated bile acids as a class and as individual compounds, and on the isolation of bile alcohols and C₂₇ bile acids diastereo-isomeric at C-25.     

Thermodynamics of the interaction of liquid-crystalline polypropyleneimine dendrimer with low-molecular-weight compounds studied by reversed-phase gas chromatography

The thermodynamic functions of dissolution of n-alkanes (C₇–C₉) and n-alkanols (C₅–C₈) in the liquid-crystalline and isotropic phases of polypropyleneimine dendrimer of the first generation at infinite dilution were determined by the reversed-phase gas chromatography. The dependences of the thermodynamic parameters of sorbates on the phase state of the dendrite solvent, hydrocarbon chain length, and polarity of low-molecular-weight components of mesogenic—nonmesogenic binary systems were considered. The role of dispersion forces and specific intermolecular interactions in the solutions under study was estimated. Saturated hydrocarbons are more compatible with columnar phases of the dendrimer than alcohols.     

Manganese(I)-Catalyzed β-Methylation of Alcohols Using Methanol as C1 Source

Highly selective β-methylation of alcohols was achieved using an earth-abundant first row transition metal in the air stable molecular manganese complex [Mn(CO)₂Br[HN(C₂H₄PⁱPr₂)₂]] 1 ([HN(C₂H₄PⁱPr₂)₂]=MACHO-ⁱPr). The reaction requires only low loadings of 1 (0.5 mol %), methanolate as base and MeOH as methylation reagent as well as solvent. Various alcohols were β-methylated with very good selectivity (>99 %) and excellent yield (up to 94 %). Biomass derived aliphatic alcohols and diols were also selectively methylated on the β-position, opening a pathway to “biohybrid” molecules constructed entirely from non-fossil carbon. Mechanistic studies indicate that the reaction proceeds through a borrowing hydrogen pathway involving metal–ligand cooperation at the Mn-pincer complex. This transformation provides a convenient, economical, and environmentally benign pathway for the selective C−C bond formation with potential applications for the preparation of advanced biofuels, fine chemicals, and biologically active molecules     

Polymethacrylates: Pour point depressants in diesel oil

A variety of techniques have been employed in order to reduce problems caused by the crystallization of paraffin during the production and/or transportation of paraffin oils and derivatives. Methacrylate copolymers are known as additives which reduce the pour point of these oils. This paper describes the synthesis, characterization and performance evaluation of these copolymers, having as an initial step the synthesis of the alkyl methacrylate monomers by transesterification of methyl methacrylate (MMA) with C₁₄, C₁₆ and C₁₈ fatty alcohols. The copolymerization of these monomers with MMA was then performed, with molar ratios of 30:70, 50:50 and 70:30 for alkyl methacrylate:methyl methacrylate. All products were characterized by FTIR, ¹H NMR and gel permeation chromatography (GPC). All the methacrylic copolymers lead to a large reduction in the pour point of samples of Brazilian diesel oil. Oil samples containing 50 ppm of the polymeric additive with ca. 70% octadecyl methacrylate units showed a 22 °C reduction in their pour points, thus establishing the large efficiency of the products synthesized in this work.     

Chromatographic properties of poly(1-phenyl-1-propyne)

The chromatographic properties of poly(1-phenyl-1-propyne) (PPP) were studied by separating the C₁–C₁₀ hydrocarbons, alcohols, aromatic, and sulfur-bearing compounds. The influence of the phase percentage for polymer adsorbent (Polysorb-1) on the process of component retention was investigated. A comparison of PPP and the nonpolar liquid phase SE-52 widely used in gas chromatography was performed.     

19F NMR determination of the C20 absolute configuration of C21-fluorinated arylthevinols

21,21,21-Trifluoro(aryl)thevinols were synthesized by the reaction of 21,21,21-trifluorothevinone with aryl Grignard reagents. The absolute configuration at C²⁰ atom in these CF₃-substituted alcohols can be easily determined by one-dimensional ¹⁹F NMR spectroscopy that was verified by X-ray diffraction studies.