Development of naphthalene and quinoxaline‐based donor–acceptor conjugated copolymers for delivering high open‐circuit voltage in photovoltaic devices

Two new quinoxaline‐based polymers, poly[1,5‐didecyloxynaphthalene‐alt‐5,5′‐(5,8‐dithiophen‐2‐yl)‐2,3‐bis(4‐octyloxyphenyl)quinoxaline (PNQx‐p) and poly[1,5‐didecyloxynaphthalene‐alt‐5,5′‐(5,8‐dithiophen‐2‐yl)‐2,3‐bis(3‐octyloxyphenyl)quinoxaline (PNQx‐m), were synthesized by Suzuki coupling reaction and characterized. Thermogravimetric analysis revealed that these polymers are thermally stable with degradation temperature up to 320 °C. As evident from the electrochemical and optical studies, the copolymers have comparable optical band gap (～2 eV) and nearly similar deep highest occupied molecular orbital (HOMO) energy levels of ?5.59 (PNQx‐p) and ?5.61 eV (PNQx‐p). The resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high open circuit voltage (V_oc) for photovoltaic applications. The optimized photovoltaic device with a structure of ITO/PEDOT:PSS/PNQx‐m:PC₇₁BM (1:2, w/w)/LiF/Al shows a power conversion efficiency up to 2.29% with a short circuit current density of 5.61 mA/cm², an V_oc of 0.93 V and a fill factor of 43.73% under an illumination of AM 1.5, 100 mW/cm². The efficiency of the PNQx‐m polymer improved from 2.29 to 2.95% using 1,8‐diiodoocane as an additive (0.25%). © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Donor-pi-acceptor conjugated copolymers for photovoltaic applications: tuning the open-circuit voltage by adjusting the donor/acceptor ratio

A class of new conjugated copolymers containing a donor (thiophene)-acceptor (2-pyran-4-ylidene-malononitrile) was synthesized via Stille coupling polymerization. The resulting copolymers were characterized by 1H NMR, elemental analysis, GPC, TGA, and DSC. UV-vis spectra indicated that the increase in the content of the thiophene units increased the interaction between the polymer main chains to cause a red-shift in the optical absorbance. Cyclic voltammetry was used to estimate the energy levels of the lowest unoccupied molecular orbital (LUMO) and the highest occupied molecular orbital (HOMO) and the band gap (Eg) of the copolymers. The basic electronic structures of the copolymers were also studied by DFT calculations with the GGA/B3LYP function. Both the experimental and the calculated results indicated an increase in the HOMO energy level with increasing the content of thiophene units, whereas the corresponding change in the LUMO energy level was much smaller. Polymer photovoltaic cells of a bulk heterojunction were fabricated with the structure of ITO/PEDOT/PSS (30 nm)/copolymer-PCBM blend (70 nm)/Ca (8 nm)/Al (140 nm). It was found that the open-circuit voltage (Voc) increased (up to 0.93 V) with a decrease in the content of thiophene units. Although the observed power convention efficiency is still relatively low (up to 0.9%), the corresponding low fill factor (0.29) indicates considerable room for further improvement in the device performance. These results provided a novel concept for developing high Voc photovoltaic cells based on donor-pi-acceptor conjugated copolymers by adjusting the donor/acceptor ratio.     

Exploring the influence of acceptor content on semi‐random conjugated polymers

A family of diketopyrrolopyrrole (DPP)‐incorporated P3HT based semi‐random copolymers was synthesized and their optical, electronic and photovoltaic properties were investigated. For the first time, the influence of acceptor content on semi‐random copolymers was explored in the broad range of 10–40% acceptor. A mixture of DPP acceptor units with different side chains (ethylhexyl and decyltetradecyl) was incorporated into each copolymer to improve solubility and film quality. Increased DPP content in the polymer backbone resulted in broadened absorption between 350 and 900 nm, resulting in a monotonic decrease in optical band gap (E_g) of the polymers from 1.49 to 1.37 eV. Highest occupied molecular orbital (HOMO) energy levels showed an increase from 10% DPP to 20–30% DPP, while decreasing for 40% DPP. V_oc values followed a consistent trend with HOMO energy levels. Semi‐random copolymers showed significantly improved photovoltaic properties compared with P3HT. Bulk heterojunction solar cells fabricated from the semi‐random copolymers blended with PC₆₁BM exhibited high short‐circuit current densities (J_sc) up to 10.29 mA/cm² and efficiencies up to 4.43%. A new method of methanol treatment was developed and applied to the semi‐random copolymers resulting in high fill factors approaching 0.70 under ambient conditions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3884–3892     

An acceptor‐acceptor conjugated copolymer based on perylene diimide for high mobility n‐channel transistor in air

A new solution‐processable acceptor‐acceptor conjugated copolymer ( P1 ) based on perylene diimide (PDI) incorporating planar electron‐deficient fluorenone was synthesized by palladium(0)‐catalyzed Suzuki coupling reaction. Relative to the donor‐acceptor conjugated copolymer ( P2 ) of PDI and dithienothiophene, polymer P1 exhibits 0.1 eV down shift of lowest unoccupied molecular orbital (LUMO) level, 70 nm blue shift of low‐energy absorption band, and 0.36 eV increase of optical band gap. Polymer P1 in top‐contact bottom‐gate organic field‐effect transistors exhibits a saturation electron mobility of 0.01 cm²/(V s) in air, while P2 does not function in the same device in air. The better air stability of P1 is attributed to a more dense packing of the polymer chains excluding oxygen or water and lower LUMO level of P1 . © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Novel narrow‐band‐gap conjugated copolymers containing phenothiazine‐arylcyanovinyl units for organic photovoltaic cell applications

A series of novel narrow‐band‐gap copolymers ( P1 ‐ P12 ) composed of alkyl‐substituted fluorene (FO) units and six analogous mono‐ and bis(2‐aryl‐2‐cyanovinyl)‐10‐hexylphenothiazine monomers ( M1 ‐ M6 ) were synthesized by a palladium‐catalyzed Suzuki coupling reaction with two different feed in ratios of FO to M1 ‐ M6 (molar ratio = 3:1 and 1:1). The absorption spectra of polymers P1 ‐ P12 exhibited broad peaks located in the UV and visible regions from 400 to 800 nm with optical band gaps at 1.55–2.10 eV, which fit near the wavelength of the maximum solar photon reflux. Electrochemical experiments displayed that the reversible p‐ and n‐doping processes of copolymers were partially reversible, and the proper HOMO/LUMO levels enabled a high photovoltaic open‐circuit voltage. As blended with [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) as an electron acceptor in bulk heterojunction photovoltaic devices, narrow‐band‐gap polymers P1 ‐ P12 as electron donors showed significant photovoltaic performance which varied with the intramolecular donor‐acceptor interaction and their mixing ratios to PCBM. Under 100 mW/cm² of AM 1.5 white‐light illumination, the device of copolymer P12 produced the highest preliminary result having an open‐circuit voltage of 0.64 V, a short‐circuit current of 2.70 mA/cm², a fill factor of 0.29, and an energy conversion efficiency of 0.51%. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4285–4304, 2008     

Low band‐gap modulation of isoindigo‐based copolymers toward high open‐circuit voltage of polymer solar cells

Designing low band‐gap‐conjugated polymers coupled with low HOMO levels attracts great attention in the field of polymer solar cells (PSCs). By using donor–acceptor (D‐A) copolymerization strategy, we designed and synthesized a series of low band‐gap copolymers with deep HOMO levels via introducing an isoindigo (IID) acceptor unit in the copolymers with the donor unit of fluorene (F) (PIID‐F), carbazole (Cz) (PIID‐Cz), thiophene (Th) (PIID‐Th), dithiophene (DTh) (PIID‐DTh), or dithienosilole (DTS) (PIID‐DTS). The HOMO level of the copolymers, measured by electrochemical cyclic voltammetry, varies from ?5.3 eV to ?5.8 eV, depending on different donor units in the copolymers. However, the LUMO levels of all the copolymers are fixed at about ?3.6 eV, which is mainly determined by IID acceptor unit due to its strong electron‐withdrawing ability. The new results will provide an effect help in designing IID based molecular structures. Among the copolymers, PIID‐DTS has a low band gap of 1.58 eV and possesses a low‐lying HOMO energy level of ?5.33 eV. The PSCs based on PIID‐DTS as donor and PC₇₀BM as acceptor exhibited a high open‐circuit voltage (V_oc) of 0.93 V and a primary power conversion efficiency of 2.45%. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3477–3485     

Soluble narrow‐band‐gap copolymers containing novel cyclopentadithiophene units for organic photovoltaic cell applications

Five novel conjugated copolymers ( P1 – P5 ) containing coplanar cyclopentadithiophene (CPDT) units (incorporated with arylcyanovinyl and keto groups in different molar ratios) were synthesized and developed for the applications of polymer solar cells (PSCs). Polymers P1 – P5 covered broad absorption ranges from UV to near infrared (400–900 nm) with narrow optical band gaps of 1.38–1.70 eV, which are compatible with the maximum solar photon reflux. Partially reversible p‐ and n‐doping processes of P1 – P5 in electrochemical experiments were observed, and the proper molecular design for highest occupied molecular orbital (HOMO)/lowest unoccupied molecular orbital (LUMO) levels of P1 – P5 induced the highest photovoltaic open‐circuit voltage in the PSC devices, compared with those previously reported CPDT‐based narrow‐band‐gap polymers. Powder X‐ray diffraction (XRD) analyses suggested that these copolymers formed self‐assembled π‐π stacking and pseudobilayered structures. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction PSC devices containing an active layer of electron donor polymers P1 – P5 mixed with electron acceptor [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) in the weight ratio of 1:4 were investigated. The PSC device containing P1 gave the best preliminary result with an open‐circuit voltage of 0.84 V, a short‐circuit current of 2.36 mA/cm², and a fill factor of 0.38, offering an overall power conversion efficiency (PCE) of 0.77% as well as a maximal quantum efficiency of 23% from the external quantum efficiency (EQE) measurements. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2073–2092, 2009     

Jacket‐like structure of donor–acceptor chromophores‐based conducting polymers for photovoltaic cell applications

Through the Stille coupling polymerization, a series of soluble acceptor/donor quinoxaline/thiophene alternating conducting polymers with a hole‐transporting moiety of carbazole as a side chain ( PCPQT ) has been designed, synthesized, and investigated. The UV–vis measurement of the charge‐transferred type PCPQT s of different molecular weights with low polydispersity exhibits a red shifting of their absorption maximum from 530 to 630 nm with increasing chain length (M_n: from 1100 to 19,200). The HOMO and LUMO energy levels of PCPQT can be determined from the cyclic voltammetry measurement to be ?5.36 and ?3.59 eV, respectively. Solar cells made from PCPQT/PCBM bulk heterojunction show a high open‐circuit voltage, V_oc of ～0.75 V, which is significantly higher than that of a solar cell made from conventional poly(3‐hexyl thiophene)/ PCBM as the active polymer PCPQT has lower HOMO level. Further improvements are anticipated through a rational design of the new low band‐gap and the structurally two‐dimensional donor–acceptor conducting polymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1607–1616, 2010     

Modulation of optical and electronic properties of quinoxailine‐based conjugated polymers for organic photovoltaic cells

The synthesis of donor–acceptor type semiconducting copolymers is described. Quinoxaline (QX) or difluorinated quinoxaline (DFQX) derivatives serve as electron acceptors, while thiophene (T) or selenophene (Se) serve as electron donors. Alternating polymers are synthesized through Stille cross‐coupling, and their thermal stability, optical and electrochemical properties, field‐effect carrier mobilities, film crystallinities, and photovoltaic performances are investigated. The intramolecular charge transfer between the electron‐donating and electron‐accepting units in the backbone induces absorption from 450 to 750 nm. The optical band‐gap energies of the polymers are between 1.65 and 1.73 eV, and depend on the polymer structure. Organic photovoltaic cells fabricated using a polymer composed of DFQX and selenophene (PSe‐DFQX) exhibit a power conversion efficiency of 5.14% with an open‐circuit voltage of 0.78 V, a short‐circuit current density of 11.71 mA/cm², and fill factor of 0.57 under AM 1.5 G irradiation (100 mW cm^?2). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1904–1914     

Direct arylation synthesis of thienoisoindigo‐based low‐band‐gap polymer from asymmetric donor–acceptor monomer

Thienoisoindigo (TIG) moiety has been paid numerous attentions as an excellent acceptor building block in low‐band‐gap polymers. Herein, a new TIG‐dithiophene alternating copolymer (PTIG2T) was successfully synthesized from an asymmetric TIG‐based donor–acceptor (D‐A) monomer via the self‐condensation‐type direct arylation polymerization. PTIG2T exhibited the light absorption over 1000 nm owing to the intramolecular charge transfer in the thin film state, which corresponded to an optical band gap of 1.24 eV. The HOMO and LUMO levels of PTIG2T were determined to be −5.08 and −3.60 eV, respectively. Furthermore, the organic photovoltaic (OPV) with a PTIG2T/PC₆₁BM active layer achieved a power conversion efficiency (PCE) of 3.19%, which is one of the highest PEC achieved by OPVs with TIG‐based materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 430–436     

Quinoxaline‐based D‐A conjugated polymers for organic solar cells: Probing the effect of quinoxaline side chains and fluorine substitution on the power conversion efficiency

We describe the successful synthesis of four novel donor‐acceptor (D‐A) type copolymers, referred to as PQxBT , PQxFBT , TQxBT , and TQxFBT . The effects of using a fluorinated bithiophene (FBT) and varying the side‐chain moieties tethered to the quinoxaline (Qx) unit (electron‐withdrawing group in the polymer backbone) on the physical properties and photovoltaic performance were investigated. Specifically, the four polymers were synthesized using either alkoxyphenyl (P) or alkylthiophene (T) units anchored to the quinoxaline in the polymer backbone. The FBT‐bearing polymers, PQxFBT and TQxFBT , displayed more redshifted absorption spectra and higher crystallinity owing to the greater planarity of their polymer backbone as compared to the non‐fluorinated polymers. The TQxFBT copolymer, equipped with both the alkylthiophene side chains and FBT, exhibited face‐on orientation in film state and a well‐mixed nanophase morphology in TQxFBT :PC₇₁BM blend films. The photovoltaic device fabricated from TQxFBT :PC₇₁BM exhibited the highest power conversion efficiency of 4.18%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1209–1218     

Synthesis and characterization of thieno[3,2‐b]thiophene‐isoindigo‐based copolymers as electron donor and hole transport materials for bulk‐heterojunction polymer solar cells

A novel class of thieno[3,2‐b]thiophene (TT) and isoindigo based copolymers were synthesized and evaluated as electron donor and hole transport materials in bulk‐heterojunction polymer solar cells (BHJ PSCs). These π‐conjugated donor‐acceptor polymers were derived from fused TT and isoindigo structures bridged by thiophene units. The band‐gaps and the highest occupied molecular orbital (HOMO) levels of the polymers were tuned using different conjugating lengths of thiophene units on the main chains, providing band‐gaps from 1.55 to 1.91 eV and HOMO levels from ?5.34 to ?5.71 eV, respectively. The corresponding lowest unoccupied molecular orbital (LUMO) levels were appropriately adjusted with the isoindigo units. Conventional BHJ PSCs (ITO/PEDOT:PSS/active layer/interlayer/Al) with an active layer composed of the polymer and PC₇₁BM were fabricated for evaluation. Power conversion efficiency from a low of 1.25% to a high of 4.69% were achieved with the best performing device provided by the D?π?A polymer with a relatively board absorption spectrum, high absorption coefficient, and more uniform blend morphology. These results demonstrate the potential of this class of thieno[3,2‐b]thiophene‐isoindigo‐based polymers as efficient electron donor and hole transport polymers for BHJ PSCs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and characterization of arylenevinylenearylene–naphthalene diimide copolymers as acceptor in all–polymer solar cells

Two n‐type conjugated D‐A copolymers, P(TVT‐NDI) and P(FVF‐NDI) with thienylene‐vinylene‐thienylene (TVT) or furanylene‐vinylene‐furanylene (FVF) as donor (D) units and naphthalene diimide (NDI) as the acceptor (A) units, were synthesized by the Stille coupling copolymerization. The two polymers possess good solubility, high thermal stability, and broad absorption bands with absorption edges at 866 nm for P(TVT‐NDI) and 886 nm for P(FVF‐NDI) . The LUMO energy levels of P(TVT‐NDI) and P(FVF‐NDI) are ?3.80 eV and ?3.76 eV respectively, so the two polymers are suitable for the application as acceptor in blending with most polymer donor in PSCs based on the energy level matching point of view. All polymer solar cells (all‐PSCs) were fabricated with P(TVT‐NDI) or P(FVF‐NDI) as acceptor and medium bandgap polymer J51 as donor for investigating the photovoltaic performance of the two n‐type conjugated polymer acceptors. And higher power conversion efficiency of 6.43% for P(TVT‐NDI) and 5.21% for P(FVF‐NDI) was obtained. The results indicate that arylenevinylenearylene–naphthalene diimide copolymer are promising polymer acceptor for all–PSCs. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1757–1764     

Ethynylene‐containing donor–acceptor alternating conjugated polymers: Synthesis and photovoltaic properties

Four ethynylene‐containing donor‐acceptor alternating conjugated polymers P1 – P4 with 2,5‐bis(dodecyloxy) substituted phenylene or carbazole as the donor unit and benzothiadiazole (BTZ) as the acceptor unit were synthesized and used as donor polymers in bulk heterojunction polymer solar cells. The optical, electrochemical, and photovoltaic properties of these four polymers with the ethylene unit located at different positions of the polymer chains were systematically investigated. Our results demonstrated that absorption spectra and the HOMO and LUMO energy levels of polymers could be tuned by varying the position of the ethynylene unit in the polymer chains. Photovoltaic devices based on polymer/PC₇₁BM blend films spin coated from chloroform and dichlorobenzene solutions were investigated. For all four polymers, open circuit voltages (V_oc) higher than 0.8 V were obtained. P4 , with ethynylene unit between BTZ and thiophene, shows the best performance among these four polymers, with a V_oc of 0.94 V, a J_sc of 4.2 mA/cm², an FF of 0.40, and a PCE of 1.6%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

New conjugated copolymers based on benzo[1,2‐b; 3,4‐b′]dithiophene and derivatives of benzo[g]quinoxaline for bulk heterojunction solar cells

A series of new low‐band gap copolymers based on dioctyloxybenzo[1,2‐b;3,4‐b′] dithiophene and bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline monomers have been synthesized via a Stille reaction. The effect of different functional groups attached to bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline was investigated and compared with their optical, electrochemical, hole mobility, and photovoltaic properties. Polymer solar cell (PSC) devices of the copolymers were fabricated with a configuration of ITO/ PEDOT: PSS/copolymers: PCBM (1:4 wt ratio)/Ca/Al. The best performance of the PSC device was obtained by using PbttpmobQ as the active layer. A power conversion efficiency of 1.42% with an open‐circuit voltage of 0.8 V, a short‐circuit current (JSC) of 5.73 mA cm⁻², and a fill factor of 30.9% was achieved under the illumination of AM 1.5, 100 mW cm⁻². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

A vinylene‐linked benzo[1,2‐b:4,5‐b']dithiophene‐2,1,3‐benzothiadiazole low‐bandgap polymer

A new heteroarylene‐vinylene donor–acceptor polymer P(BDT‐V‐BTD) with reduced bandgap has been synthesized and its photophysical, electronic and photovoltaic properties investigated both experimentally and theoretically. The structure of the polymer comprises an unprecedented combination of a strong donor (4,8‐dialkoxy‐benzo[1,2‐b:4,5‐b']dithiophene, BDT), a strong acceptor (2,1,3‐benzothiadiazole, BTD) and a vinylene spacer. The new polymer was obtained by a metal‐catalyzed cross‐coupling Stille reaction and fully characterized by NMR, UV–vis absorption, GPC, TGA, DSC and electrochemistry. Detailed ab initio computations with solvation effects have been performed for the monomer and model oligomers. The electrochemical investigation has ascertained the ambipolar character of the polymer and energetic values of HOMO, LUMO and bandgap matching materials‐design rules for optimized organic photovoltaic devices. The HOMO and LUMO energies are consistently lower than those of previous heteroarylene‐vinylene polymer while the introduction of the vinylene spacer afforded lower bandgaps compared to the analogous system P(BDT‐BTD) with no spacer between the aromatic rings. These superior properties should allow for enhanced photovoltages and photocurrents in photovoltaic devices in combination with PCBM. Preliminary photovoltaic investigation afforded relatively modest power conversion efficiencies of 0.74% (AM 1.5G, 100 mW/cm²), albeit higher than that of previous heteroarylene‐vinylene polymers and comparable to that of P(BDT‐BTD). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Novel low‐bandgap oligothiophene‐based donor‐acceptor alternating conjugated copolymers: Synthesis,properties, and photovoltaic applications

A series of novel soluble donor‐acceptor low‐bandgap‐conjugated polymers consisting of different oligothiophene (OTh) coupled to electron‐accepting moiety 2‐pyran‐4‐ylidenemalononitrile (PM)‐based unit were synthesized by Stille or Suzuki coupling polymerization. The combination of electron‐accepting PM building block with varied OTh_n (the number of thiophene unit increases from 3 to 5) results in enhanced π–π stacking in solid state and intramolecular charge transfer (ICT) transition, which lead to an extension of the absorption spectra of the copolymers. Cyclic voltammetry measurements and molecular orbital distribution calculations indicate that the highest occupied molecular orbitals (HOMO) energy levels could be fine‐tuned by changing the number of thiophene units of the copolymers, and the resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high‐open circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction photovoltaic devices were fabricated by using the copolymers as donors and (6,6)‐phenyl C₆₁‐butyric acid methyl ester as acceptor. It was found that the highest V_oc reached 0.94 V, and the short circuit currents (J_sc) were improved from 1.78 to 2.54 mA/cm², though the power conversion efficiencies of the devices were measured between 0.61 and 0.99% under simulated AM 1.5 solar irradiation of 100 mW/cm², which indicated that this series copolymers can be promising candidates for the photovoltaic applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2765–2776, 2010