Cathodic Adsorptive Voltammetry of the Gallium‐Alizarin Red S Complex at a Carbon Paste Electrode

The adsorptive voltammetric behavior of the gallium‐alizarin red S (ARS) complex in NH₄OAc‐HCl buffer at a carbon paste electrode(CPE) was investigated. The results showed that the complex can be adsorbed on the surface of the CPE, yielding one reduction peak at ?0.52 V(vs. SCE), corresponding to the irreversible reduction of the ligand, ARS, bonded in the complex. The optimal experimental conditions include the use of 0.10 mol L^?1 ammonium acetate buffer(pH 4.5), 1.0×10^?5 mol L^?1 ARS, an accumulation potential of ?0.05 V, an accumulation time of 180 s ,a rest time of 10 s, a scan rate of 200 mV s^?1and a second‐order derivative linear scan mode. The peak current is proportional to the concentration of gallium(III) over the range 0.02–6.0 μg L^?1, with the detection limit of 0.01 μg L^?1 for an accumulation time of 180 s. The method was applied to the determination of gallium in food samples with satisfactory results.     

基于酶标抗体和媒介体共吸附于金胶壳聚糖膜的PSA免疫传感器的制备

本文研制了一种用金胶壳聚糖仿生膜来同时固定四甲基联苯胺（TMB）和酶标抗体的新型电化学免疫传感器,用于检测血清肿瘤标志物前列腺特异性抗原（PSA）的含量。固定的TMB作为电子传递媒介体,在扫速小于45 mV/s时,电极表现为一个表面控制过程,而在扫速大于45 mV/s时则表现为一个扩散控制过程。将固定有酶标抗体和TMB的免疫传感器与待测PSA抗原一起培育,在该传感器上形成的免疫复合物通过TMB-H₂O₂-HRP电化学体系进行了测定。在优化实验条件下,PSA的线性检测范围为5-30 ng·mL^-1,检测限为1.0 ng·mL^-1。该PSA免疫传感器制备方法简单,成本低廉,具有较好的稳定性和重现性。     

Square‐Wave Voltammetric Determination of Paraquat at Carbon Paste Electrode Modified with Hydroxyapatite

The voltammetric behavior of paraquat was investigated at hydroxyapatite‐modified carbon paste electrode HAP‐CPE in K₂SO₄. A method was developed for the detection of the trace of this herbicide, based on their redox reaction. The reduction peaks of paraquat were observed around ?0.70 V and ?1.00 V (vs. SCE) in square‐wave voltammetry. Experimental conditions were optimized by varying the accumulation time, apatite loading and measuring solution pH. Calibration plots were linear under the optimized parameters over the herbicide's concentration range 8–200×10^?7 mol L^?1, with a detection and quantification limits about 1.5×10^?8 mol L^?1 and 6.4 10^?8 mol L^?1, respectively.     

Adsorptive Stripping Voltammetric Detection of Single‐Stranded DNA at Electrochemically Modified Glassy Carbon Electrode

Electrochemically modified glassy carbon electrode (GCE) was used to study the electrochemical oxidation and detection of denatured single‐stranded (ss) DNA by means of adsorptive stripping voltammetry. The modification of GCE, by electrochemical oxidation at +1.75 V (vs.SCE) for 10 min and cyclic sweep between +0.3 V and ?1.3 V for 20 cycles in pH 5.0 phosphate buffer, results in 100‐fold improvement in sensitivity for ssDNA detection. We speculated that the modified GCE has a high affinity to single‐stranded DNA through hydrogen bond (specific static adsorption). Single‐stranded DNA can accumulate at the GCE surface at open circuit and produce a well‐defined oxidation peak corresponding to the guanine residues at about +0.80 V in pH 5.0 phosphate buffer, while the native DNA gives no signal under the same condition. The peak currents are proportional to the ssDNA concentration in the range of 0–18.0 μg mL^?1. The detection limit of denatured ssDNA is ca. 0.2 μg mL^?1 when the accumulation time is 8 min at open circuit. The accumulation mechanism of ssDNA on the modified GCE was discussed.     

Electrocatalytic Oxidation of Vitamin B6 by 4-Hydroxy-2,2,6,6-tetramethylpiperidine-N-oxyl

Introduction Nitroxides such as 2,2,6,6-tetramethylpiperidine-N- oxyl (TEMPO) are well-known stable free radicals which have been extensively used in spin labeling,1 spin trapping2 and as antioxidants.3 Nitroxides are also easy to undergo reversible one-electron oxidation to form the corresponding oxoammonium ions.4 Oxoammonium ions are mild one-electron oxidants which have been used in organic synthesis5-8 and to generate radical cations.9 We10 found recently that electrochemically generat…     

Indication Ion Square Wave Voltammetric Determination of Thiamine and Ascorbic Acid

Abstract

Cd²⁺ ion was used as an electrochemical indicator to detect V_B1 or Vc using square ware voltammetry (SWV) at a mercury film‐coated glassy carbon (GC) electrode. At pH=10 NH₃‐NH₄Cl buffer, a new cathodic peak was found at ?0.360 V (vs.SCE) by addition of thiamine, and the peak current of SWV was linear with the concentration of thiamine in the range of 1×10^?6 to 4×10^?3 M. On the other hand, the SWV peak current of Cd²⁺ at ?0.856 V linearly decreased with addition of ascorbic acid in the range of 6×10^?6～10^?3 M. The effects of interference, such as citric acid, DL‐malic acid, and calcium panlothenate, on thiamine or ascorbic acid determination were investigated. This method was successfully applied to the determination of thiamine or in pharmaceutical preparation.     

First Electroanalytical Methodology for the Determination of Hordenine in Dietary Supplements using a Boron‐doped Diamond Electrode

The present work describes the first electrochemical investigation and a simple, rapid and modification‐free electroanalytical methodology for quantification of hordenine (a potent phenylethylamine alkaloid) using a boron‐doped diamond electrode. At optimized square‐wave voltammetric parameters, the observed oxidation peak current in 0.1 M HClO₄ at +1.33 V (vs. Ag/AgCl) increased linearly from 5.0 to 100 μg mL^?1 (3.0×10^?5–6.1×10^?4 M), with detection limit of 1.3 μg mL^?1 (7.8×10^?6 M). The applicability of the developed method was tested with the determination of hordenine in the commercial dietary supplement formulations.     

Electrochemical Studies of a New Iron Porphyrin Entrapped in a Propylpyridiniumsilsesquioxane Polymer Immobilized on a SiO2/Al2O3 Surface

In this work, a new porphyrin, the 5,10,15,20‐tetrakis‐(2,6‐difluoro‐3‐sulfonatophenyl) porphyrinato iron(III) chloride (denoted as FeTsP) was immobilized on SiO₂/Al₂O₃ (SiAl) coated with n‐propylpyridiniumsilsesquioxane polymer (SiPy⁺Cl^?). The FeTsP was adsorbed on SiAl/SiPyCl by an ion exchange reaction, obtaining a modified solid, SiAl/SiPy/FeTsP, where the porphyrin complex was strongly adhered. Cyclic voltammograms of the SiAl/SiPy/FeTsP carbon paste electrode showed an irreversible response, with an oxidation peak at E_pa=0.40 V and nondefined reduction peak at E_pc=0.15 V (vs. SCE). These peaks were not observed for the nonmetallated porphyrin, indicating that they probably correspond to the Fe(III)/Fe(II) process. Studies made in solutions having different pH, (between pH 2 and 9) using the modified electrode showed that the peak potentials and the current density were not affect by pH changes, indicating that the iron porphyrin is very stable and strongly entrapped in the matrix. The modified electrode presented the property to electrocatalyze the eletrooxidation of hydrazine at 0.41 V (vs. SCE), at pH 7. The potentiality of the SiAl/SiPy/FeTsP electrode as a sensor for hydrazine was evaluated by the using the chronoamperometric technique. A linear response was obtained in the concentration range between 5×10^?5 and 6×10^?4 mol L^?1 of hydrazine.     

Electrocatalysis via Direct Electrochemistry of Myoglobin Immobilized on Colloidal Gold Nanoparticles

The direct electron transfer between immobilized myoglobin (Mb) and colloidal gold modified carbon paste electrode was studied. The Mb immobilized on the colloidal gold nanoparticles displayed a pair of redox peaks in 0.1 M pH 7.0 PBS with a formal potential of –(0.108 ± 0.002) V (vs. NHE). The response showed a surface‐controlled electrode process with an electron transfer rate constant of (26.7 ± 3.7) s ^?1 at scan rates from 10 to 100 mV s^?1 and a diffusion‐controlled process involving the diffusion of proton at scan rates more than 100 mV s^?1. The immobilized Mb maintained its activity and could electrocatalyze the reduction of both hydrogen peroxide and nitrite. Thus, the novel renewable reagentless sensors for hydrogen peroxide and nitrite were developed, respectively. The activity of Mb with respect to the pseudo peroxidase with a K_M^app value of 0.65 mM could respond linearly to hydrogen peroxide concentration from 4.6 to 28 μM. The sensor exhibited a fast amperometric response to NO₂^? reduction and reached 93% of steady‐state current within 5 s. The linear range for NO₂^? determination was from 8.0 to 112 μM with a detection limit of 0.7 μM at 3σ.     

Electrochemical Behavior of Hydroquinone at Poly (Acridine Orange)–Modified Electrode and Its Separate Detection in the Presence of o‐Hydroquinone and m‐Hydroquinone

Abstract

Poly (acridine orange) (PAO) film–modified electrode was prepared by the electrooxidation of Acridine orange on a glassy carbon electrode (GCE) for the detection of hydroquinone in the presence of o‐hydroquinone and m‐hydroquinone. The electrochemical behavior of hydroquinone on the modified electrode was investigated with respect to different solution acidity, scan rate, and accumulation time. A pair of sharp and well‐defined peaks was obtained at 0.45 and 0.42 V [vs. a saturated calomel electrode (SCE)] at the PAO film–modified electrode. The potential difference between this pair of cathodic and anodic peaks was decreased to only 30 mV as compared to the 241 mV that was obtained on the bare glassy carbon electrode (GCE). As to o‐hydroquinone and m‐hydroquinone, their corresponding oxidation peaks appeared at 0.55 V and 0.89 V (vs. SCE), respectively. The oxidation potential differences between these three isomers enabled the separate detection of hydroquinone. Under the optimum experimental situation, the oxidation peak current of hydroquinone was proportional to the concentration at the range of 6.8×10^?7–9.6×10^?5 M. The detection limit was been estimated as 3×10^?7 M with 130 s accumulation. This method was applied to the hydroquinone detection in tap water samples.     

Direct electrochemistry of double stranded DNA on ionic liquid modified carbon paste electrode

The direct electrochemistry of herring sperm double-stranded DNA (dsDNA) on an ionic liquid N-butylpyridinium hexafluorophosphate modified carbon paste electrode was investigated. The cyclic voltammogram showed two irreversible oxidation peaks at 0.868 V and 1.188 V (vs. SCE), which corresponded to the oxidation of guanine and adenine residues, respectively. Compared to the common carbon paste electrode the electrochemical response was greatly improved. The electrochemical behavior of dsDNA on the modified electrode was carefully investigated with the electrochemical parameters were calculated. Under optimal conditions the dsDNA can be directly determined in the concentration range from 50 to 600 μg mL^?1 with a detection limit of 17 μg mL^?1 (3σ).     

Voltammetric Determination of Epinephrine with a 3‐Mercaptopropionic Acid Self‐Assembled Monolayer Modified Gold Electrode

Epinephrine (EP) could exhibit an anodic peak at a bare gold electrode, but it was very insensitive. However, when the bare gold electrode was modified with 3‐mercaptopropionic acid (3MPA) self‐assembled monolayer (3MPA SAM), the peaks of EP became more reversible and sensitive due to the accumulation and mediate efficiency of 3MPA SAM. Conditions such as solution pH, concentration of supporting electrolyte and accumulation time were optimized. Under the selected conditions (i.e., 0.02 M pH 6.8 sodium phosphate buffer, accumulation time: 2 min under open‐ circuit.), the height of the anodic peak at about 0.18 V (vs. SCE) was linear to EP concentration in the range of 2×10^?7 ?1×10^?6 M and 1×10^?6?5×10^?4 M with correlation coefficient of 0.995 and 0.999, respectively. When the 3MPA/Au was further modified with cysteamine, the interference of H₂O₂ and BrO₃^? was eliminated. But the resulting electrode still suffered from the interference of ascorbic acid. This method was used to determine the content of EP in adrenaline hydrochloride injections, and the recovery was in the range of 97.0% to 105.1%.     

Electrochemical Oxidation of Methionine Mediated by a Fullerene‐C60 Modified Gold Electrode

The usefulness of a C₆₀‐fullerene modified gold (Au) electrode in mediating the oxidation of methionine in the presence of potassium ions electrolyte has been demonstrated. During cyclic voltammetry, an oxidation peak of methionine appearing at +1.0 V vs. Ag/AgCl was observed. The oxidation current of methionine is enhanced by about 2 times using a C₆₀ modified gold electrode. The current enhancement is significantly dependent on pH, temperature and C₆₀ dosage. Calibration plot reveals linearity of up to 0.1 mM with a current sensitivity of close to 50 mA L mol^?1 and detection limit of 8.2×10^?6 M. The variation of scan rate study shows that the system undergoes diffusion‐controlled process. Diffusion coefficient and rate constant of methionine were determined using hydrodynamic method (rotating disk electrode) with values of 1.11×10^?5 cm² s^?1 and 0.0026 cm s^?1 respectively for unmodified electrode while the values of diffusion coefficient and rate constant of methionine using C₆₀ modified Au electrode are 5.7×10^?6 cm² s^?1 and 0.0021 cm s^?1 respectively.     

Determination of Active Ingredients of Hawthorn by Capillary Electrophoresis with Electrochemical Detection

A method based on capillary electrophoresis with electrochemical detection has been developed for the separa-tion and determination of epicatechin,kaempferol,chlorogenic acid,4-hydroxybenzoic acid,quercetin and proto-catechuic acid in hawthorn for the first time.The effects of working electrode potential,pH and concentration ofrunning buffer,separation voltage and injection time on CE-ED were investigated.Under the optimum conditions,the analytes could be separated in a 60 mmol·L~(-1) borate buffer(pH 8.7)within 21 min.A 300 μm diameter carbondisk electrode has a good response at 0.95 V(vs.SCE)for all analytes.The response was linear over three ordersof magnitude with detection limits(S/N=3)ranging from 3×10~(-8) to 2×10~(-7) g·mL~(-1) for the analytes.The methodhas been successfully applied to the analysis of real sample,with satisfactory results.     

Electrochemical Properties of the Oxo‐Manganese‐Phenanthroline Complex Immobilized on Ion‐Exchange Polymeric Film and Its Application as Biomimetic Sensor for Sulfite Ions

A biomimetic sensor containing the oxo‐bridged dinuclear manganese‐phenanthroline complex incorporated into a cation‐exchange polymeric film deposited onto glassy carbon electrode for detection of sulfite was studied. Cyclic voltammetry at the modified electrode in universal buffer showed a two electron oxidation/reduction of the couple Mn^IV(μ‐O)₂Mn^IV/Mn^III(μ‐O)₂Mn^III. The sensor exhibited electrocatalytic property toward sulfite oxidation with a decrease of the overpotential of 450 mV compared with the glassy carbon electrode. A plot of the anodic current versus the sulfite concentration for potential fixed (+0.15 V vs. SCE) at the sensor was linear in the 4.99×10^?7 to 2.49×10^?6 mol L^?1 concentration range and the concentration limit was 1.33×10^?7 mol L^?1. The mediated mechanism was derived by Michaelis? Menten kinetics. The calculated kinetics values were Michaelis? Menten rate constant= =1.33 µmol L^?1, catalytic rate constant=6.06×10^?3 s^?1 and heterogeneous electro‐chemical rate constant=3.61×10^?5 cm s^?1.     

Ruthenium Hexacyanoferrate (III) Modified Glassy Carbon Electrode for Determination of Captopril

A glassy carbon electrode modified with a ruthenium (III) hexacyanoferrate film was investigated for the determination of captopril in pharmaceutical formulations. The RuOHCF film was deposited on the surface of the electrode after applying 50 successive cycles and subsequent stabilization in a mixture of NaNO₃ 0.50 mol L^?1+HCl 0.050 mol L^?1 used as supporting electrolyte. The main processes responsible for the redox electrode response are attributed to the system Ru^II/Ru^III/Ru^IV, and appeared at ?0.080, 0.86 and 1.01 V (vs. SCE). The redox process at ?0.080 V was selected for the determination of captopril in the present study, once it provided higher sensibility and occurs in a lower potential than the other ones which can prevent interferences. The experimental parameters used in the determination of the analyte, using differential pulse voltammetry were optimized: pulse amplitude: 50 mV, scan rate: 5 mV s^?1 and potential window: ?0.5 to 0.2 V (vs. SCE). The analytical application of the sensor in real samples demonstrated a linear range between 0.060 and 0.80 µmol L^?1 (r=0.998) with a detection limit of 0.047 µmol L^?1. A mechanism based on co‐precipitation of captopril and the Ru (III) complex in the film is presented once the signal of the Ru^II/III redox couple decreases with increasing the analyte concentration. Recoveries of 99 to 100 % were achieved in pharmaceutical samples and the proposed procedure agreed with the HPLC official method within 95 % confidence level, according to the t‐Student test.     

Determination of Zirconium and Vanadium in Natural Waters by Adsorptive Stripping Voltammetry in the Presence of Cupferron,Oxalic Acid and 1,3‐Diphenylguanidine

A sequential AdSV method based on the accumulation of Zr(IV) and V(V) as cupferron‐oxalic acid‐1,3‐diphenylguanidine (COD) complexes at the HMDE was used to determine traces of these metals in samples with different ionic strengths. DP mode, E_ads ?0.6 and ?0.2 V (vs. Ag/AgCl, 3 mol L^?1 KCl), t_ads 400 and 20 s and 10 and 60 mV s^?1 scan rates were used for Zr(IV) and V(V), respectively. E_peak were ?0.95 (Zr(IV)‐COD) and ?0.65 V(V(V)‐COD). The methodology was applied in samples of rivers, estuaries (in Germany and Brazil) and coastal and open seawater.     

Electrochemical Determination of Oxalate at Pyrolytic Graphite Electrodes

The electrocatalytic oxidation of oxalate at several carbon based electrodes including basal plane (BPPG) and edge plane (EPPG) pyrolytic graphite and glassy carbon (GC) electrode, was studied. The electrodes were examined for the sensing of oxalate ions in aqueous solutions and all three electrodes showed a response to oxalate additions. The peak of oxalate oxidation at BPPG electrode appeared at lower potential, +1.13 V vs. SCE, than at EPPG (+1.20 V vs. SCE) and GC electrode (+1.44 V vs. SCE). Oxalate oxidation at BPPG electrode was studied in more details for response characteristics (potential and current), effects of pH, temporal characteristics of response potential and current. The results indicated that oxalate oxidation proceeds as two‐electron process at the BPPG electrode with a transfer coefficient β and a diffusion coefficient D evaluated to be 0.45 and 1.03 (±0.04)×10^?5 cm² s^?1 respectively. The BPPG electrode was found to be suitable for oxalate determination in aqueous media showing linear response to oxalate concentration with a sensitivity of 0.039 AM^?1 and a limit of detection of 0.7 μM.     

Determination of Trace Amount of Lead(II) in Sweet Fruit‐Flavored Powder Drinks by Differential Pulse Adsorptive Stripping Voltammetry at Carbon Paste Electrode

A new method is described for the determination of lead based on the cathodic adsorptive stripping of the lead–nuclear fast red (NFR) at a carbon paste electrode (CPE). The differential pulse voltammograms of the adsorbed complex of lead–NFR are recorded from ?0.10 to ?0.60 V (versus Ag/AgCl electrode). Optimal conditions were found to be an electrode containing 25% paraffin oil and 75% high purity graphite powder, 4.0×10^?5 mol L^?1 NFR; buffer solution (pH of 3.0), accumulation potential and time, ?0.20 V, 60 and 120 s (for high and low concentration of lead), respectively. The results show that the complex can be adsorbed on the surface of the CPE, yielding one peak at ?0.34 V, corresponding to reduction of NFR in the complex at the electrode. The detection limit was found to be 0.2 ng mL^?1 with a 120s accumulation time. The linear ranges are from 0.5 to 50 (t_acc=120 s) and 50 to 200 ng mL^?1 (t_acc=60 s). Application of the procedure to the determination of lead in lake water, bottled mineral water, synthetic samples and sweet fruit‐flavored powder drinks samples gave good results.     

A Novel Hydrogen Peroxide Biosensor Based on the PDDA‐GNPs/MWNTs Nanocomposite Matrix

A novel nanocomposite designed by the assembly of the positively charged poly(diallyldimethylammonium chloride) protected gold nanoparticles (PDDA‐GNPs), and the negatively charged multi‐walled carbon nanotubes (MWCNTs) on ITO electrode via electrostatic interaction, was used as a supporting matrix for immobilizing hemoglobin (Hb) to develop a high‐performance hydrogen peroxide (H₂O₂) biosensor. The cyclic voltammetrys of immobilized Hb showed a pair of well‐defined and quasi‐reversible redox peaks with the formal potential of ‐0.205V (vs. SCE) and the peak‐to‐peak potential separation of 44 mV at a scan rate of 100 mV×s^?1 in 0.1 mol×L^?1 pH 7.0 PBS. Under the optimized experimental conditions, a linearity range for determination of H₂O₂ was from 2.0 × 10^?6 to 5.2 × 10^?4 mol×L^?1 with a correlation coefficient of 0.9994 (n = 37) and a detection limit of 8.4 × 10^?7 mol×L^?1. The biosensor displayed excellent electrochemical and electrocatalytic response to the reduction of H₂O₂, high sensitivity, long‐term stability, good bioactivity and selectivity.