Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

Monodispersed nanocrystalline Co1–xZnxFe2O4 particles by forced hydrolysis: Synthesis and characterization

Zinc-substituted cobalt ferrites, Co_1–xZn_xFe₂O₄, were for the first time successfully prepared by forced hydrolysis method. The obtained materials are single phase, monodispersed nanocrystalline with an average grain size of about 3 nm. These materials are superparamagnetic at room temperature and ferrimagnetic at temperature lower than the blocking temperature. When the zinc substitution increases from x=0 to 0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g. The high saturation magnetization of these samples suggests that this method is suitable for preparing high-quality nanocrystalline magnetic ferrites for practical applications.     

Structural,magnetic and electrical properties of Co1−xZnxFe2O4 synthesized by co-precipitation method

Nanoparticles of Co_1−xZn_xFe₂O₄ with stoichiometric proportion (x) varying from 0.0 to 0.6 were prepared by the chemical co-precipitation method. The samples were sintered at 600 °C for 2 h and were characterized by X-ray diffraction (XRD), low field AC magnetic susceptibility, DC electrical resistivity and dielectric constant measurements. From the analysis of XRD patterns, the nanocrystalline ferrite had been obtained at pH=12.5–13 and reaction time of 45 min. The particle size was calculated from the most intense peak (3 1 1) using the Scherrer formula. The size of precipitated particles lies within the range 12–16 nm, obtained at reaction temperature of 70 °C. The Curie temperature was obtained from AC magnetic susceptibility measurements in the range 77–850 K. It is observed that Curie temperature decreases with the increase of Zn concentration. DC electrical resistivity measurements were carried out by two-probe method from 370 to 580 K. Temperature-dependent DC electrical resistivity decreases with increase in temperature ensuring the semiconductor nature of the samples. DC electrical resistivity results are discussed in terms of polaron hopping model. Activation energy calculated from the DC electrical resistivity versus temperature for all the samples ranges from 0.658 to 0.849 eV. The drift mobility increases by increasing temperature due to decrease in DC electrical resisitivity. The dielectric constants are studied as a function of frequency in the range 100 Hz–1 MHz at room temperature. The dielectric constant decreases with increasing frequency for all the samples and follow the Maxwell–Wagner's interfacial polarization.     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Magnetic properties of the Ce2Fe17−xMnx helical magnets up to high magnetic fields

Magnetic properties of the Ce₂Fe_17−xMn_x, x=0–2, alloys in magnetic fields up to 40 T are reported. The compounds with x=0.5–1 are helical antiferromagnets and those with 1<x?2 are helical ferromagnets or helical antiferromagnets at low and high T, respectively. Mn ions in the system carry average magnetic moment of 3.0±0.2 μ_B that couple antiparallelly to the Fe moments. Easy-plane magnetic anisotropy in the Ce₂Fe_17−xMn_x compounds weakens upon substitution of Mn for Fe. The absolute value of the first anisotropy constant in the Ce₂Fe_17−xMn_x helical ferromagnets decreases slower with increasing temperature than that calculated from the third power of the spontaneous magnetization. Noticeable magnetic hysteresis in the Ce₂Fe_17−xMn_x, x=0.5–2, helical magnets over the whole range of magnetic fields reflects mainly irreversible deformation of the helical magnetic structure during the magnetization of the compounds. A contribution from short-range order (SRO) magnetic clusters to the magnetic hysteresis of the helical magnets has been also estimated.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Spin-glass-like behavior in ZnxCryAlzSe4

The magnetic and electrical properties of the Al-doped polycrystalline spinels Zn_xCr_yAl_zSe₄ (0.13≤z≤0.55) with the antiferromagnetic (AFM) order and semiconducting behavior were investigated. A complex antiferromagnetic structure below a Néel temperature T_N≈23 K for the samples with z up to 0.4 contrasting with the strong ferromagnetic (FM) interactions evidenced by a large positive Curie-Weiss temperature θ_CW decreasing from 62.2 K for z=0.13 to 37.5 K for z=0.55 was observed. Detailed investigations revealed a divergence between the zero-field-cooling (ZFC) and field-cooling (FC) susceptibilities at temperature less than T_N suggesting bond frustration due to competing ferromagnetic and antiferromagnetic exchange interactions in the compositional range 0.13≤z≤0.4. Meanwhile, for z=0.55 a spin-glass-like behavior of cluster type with randomly oriented magnetic moments is observed as the ZFC-FC splitting goes up to the freezing temperature T_f=11.5 K and the critical fields connected both with a transformation of the antiferromagnetic spin spiral via conical magnetic structure into ferromagnetic phase disappear.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Synthesis and magnetic characterization of cobalt-substituted ferrite (CoxFe3−xO4) nanoparticles

Cobalt-substituted ferrite nanoparticles were synthesized with a narrow size distribution using reverse micelles formed in the system water/AOT/isooctane. Fe:Co ratios of 3:1, 4:1, and 5:1 were used in the synthesis, obtaining cobalt-substituted ferrites (Co_xFe_3−xO₄) and some indication of γ-Fe₃O₄ when 4:1 and 5:1 Fe:Co ratios were used. Inductively coupled plasma mass spectroscopy (ICP-MS) verified the presence of cobalt in all samples. Fourier transform infrared (FTIR) showed bands at ∼560 and ∼400 cm⁻¹, characteristic of the metal–oxygen bond in ferrites. Transmission electron microscopy showed that the number median diameter of the particles was ∼3 nm with a geometric deviation of ∼0.2. X-ray diffraction (XRD) confirmed the inverse spinel structure typical of ferrites with a lattice parameter of a=8.388 Å for Co_0.61Fe_0.39O₄, which is near that of CoFe₂O₄ (a=8.394 Å). Magnetic properties were determined using a superconducting quantum interference device (SQUID). Coercivities higher than 8 kOe were observed at 5 K, whereas at 300 K the particles showed superparamagnetic behavior. The anisotropy constant was determined based on the Debye model for a magnetic dipole in an oscillating field and an expression relating χ′ and the temperature of the in-phase susceptibility peak. Anisotropy constant values in the order of ∼10⁶ erg/cm³ were determined using the Debye model, whereas anisotropy constants in the order of ∼10⁷ erg/cm³ were calculated assuming Ωτ=1 at the temperature peak of the in-phase component of the susceptibility curve as commonly done in the literature. Our analysis demonstrates that the assumption Ωτ=1 at the temperature peak of χ′ is rigorously incorrect.     

Selected properties of EuCo2(Si1−xGex)2 alloys

EuCo₂(Si_1−xGe_x)₂, x=0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1 samples were synthesised by induction melting followed by annealing at 900 °C and rapid quenching. X-ray powder diffraction and Auger electron spectroscopy studies revealed that solid solutions are formed only for x?0.2 and x?0.7. Magnetic susceptibility investigations for the solid solutions revealed a dominant divalent europium valence state in the germanium-rich samples and a dominant trivalent europium component in the silicon-rich samples. In the germanium-rich samples, a long-range antiferromagnetic ordering was observed. In all samples studied, additional magnetic transitions at various temperatures were detected, which could be attributed to small clusters containing different europium chemical surrounding from that in the predominant phase.     

Structure and magnetostrictive properties of melt-spun Pr(Fe0.4Co0.6)1.93 alloys

Pr(Fe_0.4Co_0.6)_1.93 ribbons were prepared by a melt-spinning method. Their structure and magnetic properties are investigated as functions of wheel speed and annealing temperature. The as-spun ribbon consists of a Pr(Fe, Co)₂ cubic Laves phase and an amorphous phase at a wheel speed of v≥35 m/s, while the non-cubic phases of PuNi₃-type and rare earth appear when the speed lower than 30 m/s. A single Pr(Fe, Co)₂ phase with MgCu₂-type structure has been synthesized by the process for the wheel speed of v≥35 m/s and subsequent annealing at 500 °C for 30 min. The epoxy/Pr(Fe_0.4Co_0.6)_1.93 composite has been produced by a cold isostatic pressing technique, and the magnetic properties have been investigated. The composite rod sample possesses good magnetostrictive properties, i.e., a large magnetostriction (λ_a=λ_∥−λ_⊥) of 710 ppm at 800 kA/m and a dynamic coefficient d₃₃ of 0.67 nm/A at 100 kA/m, and is of practical value.     

Ferromagnetic resonance studies on (Co40Fe40B20)x(SiO2)1−x granular magnetic films

Magnetic properties of granular (Co₄₀Fe₄₀B₂₀)_x(SiO₂)_1−x   thin films (x=0.37-0.53$x=0.37-0.53$) have been studied by ferromagnetic resonance (FMR) technique. Samples have been prepared by ion-beam deposition of Co–Fe–B particles and SiO₂ on sitall ceramic substrate. The FMR measurements have been done for different orientations of DC magnetic field with respect to the sample plane. It was found that the deduced value of effective magnetization from FMR data of the thin granular film is reduced by the volume-filling factor of the bulk saturation magnetization. The overall magnetization changes from 152 to 515 G depending on the ratio of the magnetic nanoparticles in the SiO₂ matrix. From angular measurements an induced in-plane uniaxial anisotropy has been obtained due to the preparation of the film conditions as well.     

Large vertical loop shifts in mechanically synthesized (Mn,Fe)2O3−t nanograins

Magnetic properties of zero field cooled (ZFC) and field cooled (FC) sample of (Mn,Fe)₂O_3−t nanograins have been investigated by magnetometry (up to 70 kOe) and Mössbauer spectroscopy (up to 60 kOe) in the temperature interval 4.2–300 K. Large horizontal (up to 0.8 kOe) and vertical (up to 80%) shifts of the magnetization hysteresis loops are observed in the FC regime. The obtained results are discussed in terms of exchange interaction between an antiferromagnetic core and a spin-glass-like state of the nanograins boundaries. It is shown that hysteresis loop shifts (horizontal and vertical) depend on the field cooling magnitude, an effect that can be understood by the change of the boundary magnetic structure induced by the external magnetic field. The vertical magnetization shift is described by a phenomenological model, which takes into account the magnetic interaction between the spin-glass like boundary spins and the applied field.     

Magnetic ordering in the frustrated system FeSc2S4

The sample of FeSc₂S₄ was prepared by solid reaction method. The crystallographic structure and the magnetic properties of the fabricated compound were investigated by X-ray, and superconducting quantum interference device (SQUID) magnetometer and Mössbauer spectroscopy. The polycrystalline FeSc₂S₄ confirmed the normal cubic spinel structure (space group Fd3m). The lattice constants a₀ and anion parameter u are 10.519 Å and 0.255, respectively. The Mössbauer spectroscopy has been studied for the FeSc₂S₄ at various temperatures, ranging from 4.2 K to room temperature. The spectra consist of two doublets at 4.2 K while a single line at room temperature. It is noticeable that the Mössbauer spectra of two doublet patterns with large electric quadrupole splitting (ΔE_Q) remain over the Néel temperature. Those are interpreted as a result of large electric quadrupole interaction compared to magnetic dipole interaction. The magnetic susceptibility measurements were performed with a SQUID magnetometer for temperatures 2<T<320 K, in external fields up to 5 kOe. Magnetic behavior shows antiferromagnetic behavior and the magnetic superexchange interactions between the Fe ions are weakly antiferromagnetic. The paramagnetic susceptibilities follow Curie–Weiss (CW) law with CW temperature Θ_CW=−100 K, and frustration parameter f=−Θ_CW/T_N is of the order of 1000. We conclude that two sublattices are coupled antiferromagnetically, leading to strong frustration effects.     

Magnetic domain structure in Fe78.8−xCoxCu0.6Nb2.6Si9B9 nanocrystalline alloys studied by Lorentz microscopy

The magnetic domain structures of Fe_78.8−xCo_xCu_0.6Nb_2.6Si₉B₉ (x=0, 20, 40, 60) alloys are investigated by Lorentz microscopy coupled with the focused ion beam method. The specimen prepared using the FIB method is found to have a considerably more uniform thickness compared to that prepared using the ion-milling method. In Fe_38.8Co₄₀Cu_0.6Nb_2.6Si₉B₉ and Fe_18.8Co₆₀Cu_0.6Nb_2.6Si₉B₉ alloys, 180° domain walls extending in the direction of the induced magnetic anisotropy are observed. Analysis with Lorentz microscopy reveals that the width of the magnetic domains decreases with an increase in the cobalt content or the induced magnetic anisotropy K_u, that is, the domain width d is proportional to the induced magnetic anisotropy (K_u)^−1/4. On the other hand, in the in situ Lorentz microscopy observation as a function of temperature, magnetic ripple structures are found to appear in a localized area due to the fluctuation of magnetization vectors from 423 K. It is observed that the induced magnetic anisotropy caused by the applied magnetic field at 803 K is not suppressed by the magnetic ripple structures observed at 423–443 K.     

Magnetic properties of nanocrystalline Co1−xZnxFe2O4 prepared by forced hydrolysis method

Nanocrystalline zinc-substituted cobalt ferrite powders, Co_1−xZn_xFe₂O₄ (x=0, 0.2, 0.4), were for the first time prepared by forced hydrolysis method. Magnetic and structural properties in these specimens were investigated. The average crystallite size is about 3.0 nm. When the zinc substitution increases from x=0 to x=0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g and the coercive field decreases from 1.22 to 0.71 T. All samples are superparamagnetic at room temperature and ferrimagnetic at temperatures below the blocking temperature. The high value of the saturation magnetization and the very thin thickness of the disorder surface layer of all samples suggests that this forced hydrolysis method is suitable not only for preparing two metal element systems but also for three or more ones.     

Antiferromagnetism and spin-glass transition in the FeInxCr2−xSe4 series of selenides

The magnetic behavior of the FeIn_xCr_2−xSe₄ system (with x=0.0, 0.2 and 0.4) has been investigated by magnetic and Mössbauer spectroscopy. Hyperfine parameters indicate that iron is in the Fe²⁺ oxidation state, with a minor (∼9%) Fe³⁺ fraction, located at different layers in the structure. Low-field magnetization curves as a function of temperature showed that the antiferromagnetic (AFM) order temperature is T_N=208(2) K for FeCr₂Se₄ and decreases to 174(3) K for FeIn_0.4Cr_1.6Se₄. The effective magnetic moment μ_eff decreases with increasing In contents, and shows agreement with the expected values from the contribution of Fe²⁺ (⁵D) and Cr³⁺ (⁴F) electronic states. A second, low-temperature transition is observed at T_G∼13 K, which has been assigned to the onset of a glassy state.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Magnetic structure and phase diagram of the frustrated spinel Cd1−xZnxCr2Se4

In attempt to characterise the magnetic ordering in the whole composition range of the Cd_1−xZn_xCr₂Se₄ system, various magnetic measurements were performed on both crystalline and polycrystalline samples with 0?x?1. The magnetic properties of the system are typical of a ferromagnet below x=0.4 and of a complex antiferromagnet one above x=0.6. In this work the intermediate region was carefully studied. The variations of both M(T) and χ_ac at low fields suggest that transitions from ferromagnetic to Gabay–Toulouse ferromagnetic-spin-glass mixed phase at low temperature occur in the range 0.41?x?0.58. The high-temperature susceptibility measurements show that for the whole concentration range the system obeys Curie–Weiss laws. The results can be explained by the coexistence of competing interactions (ferromagnetic between nearest neighbours and antiferromagnetic between higher order neighbours) and disorder due to the random substitution between zinc and cadmium ions in the tetrahedral sites of the spinel lattice. An experimental magnetic phase diagram of the system is established.