Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Magnetic and Mössbauer studies of Ni substituted Li-Zn ferrite

Li-Zn ferrites substituted with Ni having the compositional formula Li_0.4−0.5xZn_0.2Ni_xFe_2.4−0.5xO₄ where x=0.02?x?0.1 in steps of 0.02 were fabricated by the citrate precursor method. This method has been employed to get nanosized particles and good magnetic properties. The spinel phase structure of the prepared ferrites was confirmed by XRD analysis. The effect of Ni concentration on magnetic properties such as saturation magnetization and Curie temperature were investigated. A good knowledge of these magnetic properties is desirable from application point of view. The values observed are large and both quantities were found to decrease with substitution. The saturation magnetizations were found to vary from 78 to 94 emu/gm while the Curie temperature which limits the operating temperature of the system ranges between 563 and 584 °C. Mössbauer data were also recorded at room temperature and the hyperfine parameters like isomer shift, quadrupole splitting and internal magnetic field estimated. The results obtained and mechanisms involved are discussed.     

Electromagnetic properties of samarium-substituted NiCuZn ferrite prepared by auto-combustion method

Ni_0.25Cu_0.2Zn_0.55Sm_xFe_2−xO₄ ferrite with x=0.00, 0.025, 0.05 and 0.075 compositions were synthesized through the nitrate-citrate auto-combustion method. These powders were calcined, compacted and sintered at 900 °C for 4 h. Effect of Sm substitution on phase composition, microstructure and relative density were studied. Permeability, magnetic loss and AC resistivity were measured in the frequency range of 1 kHz-10 MHz. Permeability and AC resistivity were found to increase and loss decreased with Sm substitution up to x=0.05. Saturation magnetization also increased up to that substitution limit. Observed variations in electromagnetic properties have been explained.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Structural and magnetic properties of Mg(In2−xMnx)O4 system

We synthesized the Mn-doped Mg(In_2−xMn_x)O₄ oxides with 0.03?x?0.55 using a solid-state reaction method. The X-ray diffraction patterns of the samples were in a good agreement with that of a distorted orthorhombic spinel phase. Their lattice parameters and unit-cell volumes decrease with x due to the substitution of the smaller Mn³⁺ ions to the larger In³⁺ ions. The undoped MgIn₂O₄ oxide presents diamagnetic signals for 5 K?T?300 K. The M(H) at T=300 K reveals a fairly negative-sloped linear relationship. Neither magnetic hysteresis nor saturation behavior was observed in this parent sample. For the Mn-doped samples, however, positive magnetization were observed between 5 and 300 K even if the x value is as low as 0.03. The mass susceptibility enhances with Mn content and it reaches the highest value of 1.4×10⁻³ emu/g Oe (at T=300 K) at x=0.45. Furthermore, the Mn-doped oxides with x=0.06 and 0.2, respectively, exhibit nonlinear magnetization curves and small hysteretic loops in low magnetic fields. Susceptibilities of the Mn-doped samples are much higher than those of MnO₂, Mn₂O₃ oxides, and Mn metals. These results show that the oxides have potential to be magnetic semiconductors.     

Magnetic entropy-change in La0.67−xBixCa0.33MnO3 compound

Bi doped lanthanum manganites with the chemical composition of La_0.67−xBi_xCa_0.33MnO₃ (x=0$x=0$, 0.05, 0.1, 0.2) were prepared by the standard solid-state process. The Curie temperatures were measured to be 267 K for x=0$x=0$, 248 K for x=0.05$x=0.05$, 244 K for x=0.1$x=0.1$ and 229 K for x=0.2$x=0.2$ samples. It was found that the maximum value of the magnetic entropy change ∣ΔS_m∣ has reached the highest value of 6.08 J/kg K at 3 T for the composition with x=0.05$x=0.05$. Nearly the same maximum entropy change was observed for the x=0$x=0$ sample. A large decrease in the magnitude of the entropy change was observed for the x=0.2$x=0.2$ sample.     

Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

Curie temperatures and crystallization behavior of amorphous Fe81−xNixZr7B12 (x=10, 20, 30, 40, 50, 60) alloys

Curie temperature, crystal structure and crystallization behavior of amorphous alloys with the stoichiometry Fe_81−xNi_xZr₇B₁₂ (x=10–60) have been studied by X-ray diffractometry (XRD), differential scanning calorimetry (DSC) and AC-magnetization (TMAG) measurements as functions of temperature. The thermal stability of long-range magnetic order, T_C vs. Ni content in as-quenched amorphous alloys exhibits maximum at 352 °C for x=40. The primary crystallization has been detected during annealing at the first crystallization stage of all ribbons investigated.     

Production of bulk dilute ferromagnetic semiconductor by mechanical milling

We tried to prepare the bulk dilute ferromagnetic semiconductor (DMS) by mechanical milling (MM). Experimental results were as following: (1) The observation of X-ray diffraction and transmitting electron microscopy showed that the particle diameter of host ZnO powder were reduced to about 10 nm by MM. (2) The MM for the mixtures of V₂O₅/ZnO or γ-Fe₂O₃/ZnO realizes the V- or Fe-doped ZnO nano-powders. (3) The values of magnetization under the field of 5 kOe were nearly saturated to 0.8×10⁻³ to 3×10⁻³ μ_B/V-ion for V_xZn_1−xO (x=0.05, 0.1 and 0.2), and 0.2–0.3 μ_B/Fe-ion for Fe_xZn_1−xO (x=0.05 and 0.1) at room temperature. The above results show that the ferromagnetic DMS powder of V_xZn_1−xO and Fe_xZn_1−xO were successfully prepared by MM method.     

Structural,electrical transport,and magnetic properties of Ni1−xZnxFe2O4

Structural, electrical, and magnetic properties of Ni_1−xZn_xFe₂O₄ (x=0.2, 0.4) samples sintered at various temperatures have been investigated thoroughly. The bulk density of the Ni_0.8Zn_0.2Fe₂O₄ samples increases as the sintering temperature (T_s) increases from 1200 to 1300 °C and above 1300 °C the bulk density decreases slightly. The Ni_0.6Zn_0.4Fe₂O₄ samples show similar behavior of changes to that of Ni_0.8Zn_0.2Fe₂O₄ samples, except that the bulk density is found to be the highest at 1350 °C. The DC electrical resistivity, ρ(T)$\rho (T)$, decreases as the temperature increases indicating that the samples have semiconductor-like behavior. As the Zn content increases, the Curie temperature (T_c), resistivity, and the activation energy decrease while the magnetization, initial permeability, and the relative quality factor (Q) increases. A Hopkinson peak is obtained near T_c in the real part of the initial permeability vs. temperature curves. The ferrite with higher permeability has a relatively lower resonance frequency. The initial permeability and magnetization of the samples has been found to correlate with density, average grain sizes. Possible explanation for the observed structural, magnetic, and changes of resistivity behavior with various Zn content are discussed.     

The effect of B2O3 addition to the microstructure and magnetic properties of Ni0.4Zn0.6Fe2O4 ferrite

The effects of 0.01 and 0.1 mol B₂O₃ addition to the microstructure and magnetic properties of a Ni–Zn ferrite composition expressed by a molecular formula of Ni_0.4Zn_0.6Fe₂O₄ were investigated. The toroid-shaped samples prepared by pressing the milled raw materials used in the preparation of the composition were sintered in the range of 1000–1300 °C. The addition of 0.01 mol B₂O₃ increased the grain growth and densification giving rise to reduced intergranular and intragranular porosity due to liquid-phase sintering. The sintered toroid sample at 1300 °C gave the optimum magnetic properties of B_r=170 mT, H_c=0.025 kA/m and a high initial permeability value of μ_i=4000. The increment of the B₂O₃ content to 0.1 mol resulted in a pronounced grain growth and also gave rise to large porosity due to the evaporation of B₂O₃ at higher sintering temperatures. Hence, it resulted in an air-gap effect in the hysteresis curves of these samples.     

Influence of annealing temperature on structural, optical and magnetic properties of Mn-doped ZnO thin films prepared by sol-gel method

Thin films of Zn_1−xMn_xO (x=0.01) diluted magnetic semiconductor were prepared on Si (1 0 0) substrates by the sol-gel method. The influence of annealing temperature on the structural, optical and magnetic properties was studied by X-ray diffraction (XRD), atom force microscopy (AFM), photoluminescence (PL) and SQUID magnetometer (MPMS, Quantum Design). The XRD spectrum shows that all the films are single crystalline with (0 0 2) preferential orientation along c-axis, indicating there are not any secondary phases. The atomic force microscopy images show the surfaces morphologies change greatly with an increase in annealing temperature. PL spectra reveal that the films marginally shift the near band-edge (NBE) position due to stress. The magnetic measurements of the films using SQUID clearly indicate the room temperature ferromagnetic behavior, and the Curie temperature of the samples is above room temperature. X-ray photoelectron spectroscopy (XPS) patterns suggest that Mn²⁺ ions were successfully incorporated into the lattice position of Zn²⁺ ions in ZnO host. It is also found that the post-annealing treatment can affect the ferromagnetic behavior of the films effectively.     

Enhanced magnetoresistance effects in bulk polycrystalline Ag-added magnetite

A series of bulk polycrystalline Ag-added Fe₃O₄ with a nominal composition, (Fe₃O₄)_1−xAg_x (x is molar fraction) with x=0, 0.1, 0.2, 0.3, 0.4, and 0.5 have been prepared by conventional solid-state reaction. X-ray diffraction patterns show that the pure Fe₃O₄ sample (x=0) has a single-phase inverse spinel structure, while the Ag-added samples are two-phase composites consisting of a ferrimagnetic Fe₃O₄ phase and a non-magnetic metal Ag phase. The bright-field transmission electron microscopy images exhibit that the samples are typical granular solids with a porosity of about 22%. The addition of Ag slightly increases the average grain size of the Fe₃O₄ phase and significantly enhances the MR effect of bulk polycrystalline Fe₃O₄ samples. Of all the samples the x=0.3 sample has a maximal MR of −5.1% at 300 K in a magnetic field of 1 T, and −6.8% in 5 T, which are approximately three times greater than the corresponding MR values (−1.8% at 1 T and −2.4% at 5 T) of the Fe₃O₄ sample. This enhancement of the MR can be attributed to the combination effect from the spin-dependent scattering at the interfaces between the Fe₃O₄ grains and the Ag granules and the spin-polarized tunneling at grain boundaries of Fe₃O₄ phase of the spin-polarized electrons.     

Study on electro-magnetic properties of La substituted Ni–Cu–Zn ferrite synthesized by auto-combustion method

(Ni_0.25Cu_0.20Zn_0.55)La_xFe_2−xO₄ ferrite with x=0.00, 0.025, 0.050 and 0.075 compositions were synthesized through nitrate–citrate auto-combustion method. Crystalline spinel ferrite phase with about 16–19 nm crystallite size was present in the as-burnt ferrite powder. These powders were calcined, compacted and sintered at 950 °C for 4 h. Initial permeability, magnetic loss and AC resistivity of different compositions were measured in the frequency range from 10 Hz to 10 MHz. Saturation magnetization and hysteresis parameters were measured at room temperature with a maximum magnetic field of 10 kOe. Permeability and AC resistivity were found to increase and magnetic loss decreased with La substitution for Fe, up to x=0.025. Saturation magnetization and coercive field also increases up to that limit. The electromagnetic properties were found best in the ferrite composition of x=0.025, which would be better for more miniaturized multi layer chip inductor.     

Antiferromagnetism and spin-glass transition in the FeInxCr2−xSe4 series of selenides

The magnetic behavior of the FeIn_xCr_2−xSe₄ system (with x=0.0, 0.2 and 0.4) has been investigated by magnetic and Mössbauer spectroscopy. Hyperfine parameters indicate that iron is in the Fe²⁺ oxidation state, with a minor (∼9%) Fe³⁺ fraction, located at different layers in the structure. Low-field magnetization curves as a function of temperature showed that the antiferromagnetic (AFM) order temperature is T_N=208(2) K for FeCr₂Se₄ and decreases to 174(3) K for FeIn_0.4Cr_1.6Se₄. The effective magnetic moment μ_eff decreases with increasing In contents, and shows agreement with the expected values from the contribution of Fe²⁺ (⁵D) and Cr³⁺ (⁴F) electronic states. A second, low-temperature transition is observed at T_G∼13 K, which has been assigned to the onset of a glassy state.     

Microstructure and magnetic properties of bulk amorphous and nanocrystalline Fe61Co10Zr2.5Hf2.5Nb2W2B20 alloy

The microstructure and magnetic properties, i.e. the initial magnetic susceptibility, its disaccommodation, core losses and approach to ferromagnetic saturation of the bulk amorphous and partially crystallized Fe₆₁Co₁₀Zr_2.5Hf_2.5Nb₂W₂B₂₀ alloy are studied. From X-ray, Mössbauer spectroscopy and electron microscopy studies we have stated that all samples in the as-quenched state are fully amorphous. However, after annealing the samples at 850 K for 30 min the crystalline α-FeCo grains embedded in the amorphous matrix are found. Moreover, from Mössbauer spectra analysis we have stated that the crystalline phase in those samples exhibits the long-range order. The alloy in the as-quenched state shows good thermal stability of the initial magnetic susceptibility. Furthermore, the intensity of the magnetic susceptibility disaccommodation in the rod is lower than in the ribbon. It is due to low quenching rate during the rod preparation which involves the reduction of free volumes. From the analysis of the isochronal disaccommodation curves, assuming the Gaussian distribution of relaxation times, we have found that activation energies of the elementary processes responsible for this phenomenon range from 1.2 to 1.4 eV. After the annealing of the samples the initial susceptibility slightly enhances and disaccommodation drastically decreases. From high-field magnetization studies we have learned that the size of structural defects depends on the quenching rate (the shape of the samples) and changes after annealing.     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Effect of K doping on the physical properties of La0.65Ca0.35−xKxMnO3 (0?x?0.2) perovskite manganites

The effects of K doping in the A-site on the structural, magnetic and magnetocaloric properties in La_0.65Ca_0.35−xK_xMnO₃ (0?x?0.2) powder samples have been investigated. Our samples have been synthesized using the solid-state reaction method at high temperature. The parent compound La_0.65Ca_0.35MnO₃ is an orthorhombic (Pbnm space group) ferromagnet with a Curie temperature T_C of 248 K. X-ray diffraction analysis using the Rietveld refinement show that all our synthesized samples are single phase and crystallize in the orthorhombic structure with Pbnm space group for x?0.1 and in the rhombohedral system with R3¯c space group for x=0.2 while La_0.65Ca_0.2K_0.15MnO₃ sample exhibits both phases with different proportions. Magnetization measurements versus temperature in a magnetic applied field of 50 mT indicate that all our investigated samples display a paramagnetic-ferromagnetic transition with decreasing temperature. Potassium doping leads to an enhancement in the strength of the ferromagnetic double-exchange interaction between Mn ions, and makes the system ferromagnetic at room temperature. Arrott plots show that all our samples exhibit a second-order magnetic-phase transition. The value of the critical exponent, associated with the spontaneous magnetization, decreases from 0.37 for x=0.05 to 0.3 for x=0.2. A large magnetocaloric effect (MCE) has been observed in all samples, the value of the maximum entropy change, |ΔS_m|_max, increases from 1.8 J/kg K for x=0.05 to 3.18 J/kg K for x=0.2 under a magnetic field change of 2 T. For x=0.15, the temperature dependence of |ΔS_m| presents two maxima which may arise from structural inhomogeneity.     

Synthesis and magnetic properties of Ni-doped zinc oxide powders

Polycrystalline Zn_1−xNi_xO diluted magnetic semiconductors have been successfully synthesized by an auto-combustion method. X-ray diffraction measurements indicated that the 5 at% Ni-doped ZnO had the pure wurtzite structure. Refinements of cell parameters from powder diffraction data revealed that the cell parameters of Zn_0.95Ni_0.05O were a little bit larger than ZnO. Transmission electron microscopy observation showed that the as-synthesized powders were of the size ∼60 nm. Magnetic investigations showed that the nanocystalline Zn_0.95Ni_0.05O possessed room temperature ferromagnetism with the saturation magnetic moment of 0.1 emu/g (0.29 μ_B/Ni²⁺).