Ce_(0.8)Nd_(0.2)O_(1.9)-La_(0.95)Sr_(0.05)Ga_(0.9)Mg_(0.1)O_(3-δ)固体复合电解质的结构和电性能

采用溶胶-凝胶法分别制备La0.95Sr0.05Ga0.9Mg0.1O3-δ(LSGM)和Ce0.8Nd0.2O1.9(NDC)电解质,并在NDC溶胶中加入0-15%(w,质量分数)的LSGM预烧粉体制得NDC-LSGM复合电解质,研究不同质量比复合电解质的结构和电性能.采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和X能量色散谱仪(EDS)对样品进行结构表征,交流(AC)阻抗谱测试样品导电性能.结果表明:NDC-LSGM复合体系主要由立方萤石结构相、钙钛矿结构相和杂质相组成;LSGM的添加可促进晶粒的生长,产生大量相界面,清除或降低SiO2有害影响,明显提高晶界导电性;LSGM质量分数为10%的样品NL10具有最高晶界电导率和总电导率,400°C时NL10的晶界电导率σgb和总电导率σt分别为12.15×10-4和3.49×10-4S cm-1,与NDC的σgb(1.41×10-4S cm-1)和σt(1.20×10-4S cm-1)相比分别提高了7.62和1.91倍,总电导率的提高主要归因于晶界电导率的影响.     

Li_(3.22)Na_(0.569)Mn_(5.78)O_(12.0)的电化学性能

以L iOH.H2O和Mn(CH3COO)2.2H2O作原料,应用微波-固相两段烧结法合成具有L i4Mn5O12结构特征,组成为L i3.22Na0.569Mn5.78O12.0的锂离子电池正极材料.XRD分析表明,在380℃的后处理温度下,微波烧结前处理有利于生成纯L i4Mn5O12尖晶石相.充放电实验表明,在4.5~2.5V电压区间,新制样品的初始放电容量为132 mAh.g-1,100循环的容量衰减率为6.8%;4个月存放样的初始放电容量为122 mAh.g-1,100循环的容量衰减率为17.4%.表现出较好的充放电性能和循环寿命.微波烧结使样品的Mn-O键被加强.     

La_(0.7)Pr_(0.15)Nd_(0.05)Mg_(0.3)Ni_(3.3-x)Co_(0.2)Al_(0.1)(Co_(0.75)Mn_(0.25))_x(x=0.0,0.2,0.4,0.6)的电化学性能研究

在Ar气保护下用悬浮熔炼制备La0.7Pr0.15Nd0.05Mg0.3N i3.3-xCo0.2A l0.1(Co0.75Mn0.25)x(x=0.0,0.2,0.4,0.6)合金,系统研究了Co和Mn对合金储氢性能和电化学性能的影响。XRD相分析表明,合金相主要由(La,Pr)(N i,Co)5,LaMg2N i9,(La,Nd)2N i7和LaN i3相组成;添加Co和Mn后合金中(La,Pr)(N i,Co)5,(La,Nd)2N i7和LaN i3相晶胞体积增加,LaMg2N i9相晶胞体积变小。合金放氢PCT曲线测试表明,随着合金中Co和Mn含量的增加,合金吸氢量先减小后增加,放氢平台压下降,合金氢化物稳定性增加。合金电极电化学性能测试表明,添加Co和Mn使合金电极放电容量减小,容量保持率S100从53.2%(x=0.0)增加到63.0%(x=0.6),合金电极的电循环稳定性增强,高倍率放电性能HRD1500先增加后减小。此外,合金电极的极化电阻先减小后增加,交换电流密度、循环伏安特性阳极峰电流密度和极限电流密度先增加后减小,合金内氢原子扩散系数先增加后减小,表明添加适量的Co和Mn可以提高合金电...     

Novel Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ) membranes for POM

A novel cobalt-free perovskite based on Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ)(BSFZ)were prepared by EDTA-citric acid method.The lattice constants of the BSFZ perovskite were characterized by in situ high-temperature X-ray diffraction(HTXRD).The thermal expansion coefficient of BSFZ is 10.5×10~(-6)K~(-1),which is lower than that of cobalt-based perovskite materials.The BSFZ membrane was also used to construct reactors for the partial oxidation of methane(POM)to syngas.Results show that the BSFZ membrane...     

Synthesis and Crystal Structure of Trans-diaquabis(hexamethylenetetramine-N)bis(isothiocyanato)cobalt(Ⅱ) trans-tetraaquabis(isothiocyanato)cobalt(Ⅱ) dihydrate

1 INTRODUCTION Supramolecular compounds assembled by coordination covalent bonding or hydrogen bonding are of considerable interest due to their potential applications in developing new materials with magnetic, optical and catalytic properties[1]. One of the synthesis methods used to construct the functional compounds is that octahedral metal ion connects to polydentate ligand such as 4, 4?bipyridine, pyrazine and so on to form multi-dimensional supramolecular polymer[2]. Hmt (hexamethyl…     

双水相萃取法分离铍(Ⅱ)、铁(Ⅲ)与铁(Ⅱ)、铬(Ⅲ)、锰(Ⅱ)、铝(Ⅲ)

研究了在聚乙二醇2000(PEG)-硫酸钠(Na2SO4)-邻苯二酚紫(PV)体系中铍(Ⅱ)、铁(Ⅲ)、铁(Ⅱ)、铝(Ⅲ)、铬(Ⅲ)、锰(Ⅱ)的萃取行为。试验结果表明,铍(Ⅱ)在pH 3.5-7.0及铁(Ⅲ)在pH 4.0-7.0范围内可以被PEG相几乎完全萃取,而铝(Ⅲ)、铬(Ⅲ)在pH 1.0-7.0、锰(Ⅱ)在pH 1.0-4.5、铁(Ⅱ)在pH 1.0-4.5则不被萃取。从而实现了将铍(Ⅱ)(pH 3.5)、铁(Ⅲ)(pH 5.0)与铝(Ⅲ)、铬(Ⅲ)、锰(Ⅱ)、铁(Ⅱ)混合离子的定量分离。同时探讨了PEG相的萃取机理。     

X-ray structures of trans-dichloro(4-methylpyrimidine) (η1-phenyl)bis(pyridine)rhodium(III) hydrate and trans-dichloro(phenyl)tris(triphenylstibine)rhodium(III) ethylacetate solvate. Molecular orbital analysis of trans-dichloro (4-methylpyrimidine)(η1-phenyl)bis(pyridine)rhodium(III)

The crystal and molecular structure of trans-dichloro(4-methylpyrimidine)(η ¹ -phenyl)cis-bis(pyridine)rhodium(III) water solvate, 1x 0.17H₂ O, and trans-dichloro(η ¹ -phenyl)tris(triphenylstibine)rhodium(III) ethylacetate solvate, 2x CH₃ CO₂ CH₂ CH₃ have been studied via X-ray diffraction from a single crystal at room temperature. The final refinement converged to R1 conventional index of 0.0350 and 0.0361 for the structural analysis of 1x 0.17H₂ O [space group R(-3) and 2x CH₃ CO₂ CH₂ CH₃ P(-1) , respectively. The 4-methylpyrimidine ligand (Pym) is only weakly bound to Rh in 1, as shown by the long Rh-N distance (2.251(4) Å), compared to the Rh N(pyridine) lengths average, 2.066(4) . N-C bond distances involving the N donor average 1.329(6) and 1.345(6) for Pym and pyridine (Py) ligands, respectively. The C N C bond angle on the donor is 114.1(5)° for Pym and average 117.4(4)^° for Py.The structure of the complex molecule of 2x CH₃ CO₂ CH₂ CH₃ has some differences when compared to that of the corresponding acetone solvate previously studied in this laboratory (Cini, R., Giorgi, G. and Pasquini, L., Inor`. Chim. Acta, 1992, 196, 7). The two structures differ mainly by the orientation of the phenyl donor with respect to the Cl-Rh-Cl axis (which is more eclipsed for the ethylacetate solvate) and by the conformation of the SbPh₃ ligands.Density functional calculations at the B3LYP/LANL2DZ level with full geometry optimization were carried out on the free Pym molecule and on some Sc(N ¹ Pym) ^{3 +}and Sc(N ² Pym) ^{3 +} model molecules. The effect of metal coordination consists mainly in enlarging the (Sc)N-C bond distances up to 0.150Å, whereas the C-N(Sc)-C bond angle decreases of 1.9°. Significant changes on other bond lengths and angles relevant to ring atoms of Pym occur upon metal coordination to the nitrogen atom. The metal coordination to N(2) is less favorable than to N(1) of 7.5 kcal for 1:1 species of Sc^{3 +}Extended Hückel calculations showed that HOMO consists mostly of metal-d orbitals with some character of chloride and phenyl and pyrimidine ligands, whereas LUMO is composed of phenyl, pyridine and pyrimidine orbitals. The method well reproduces the Rh-N and Rh-C bonding distances and gives Rh-C dissociation energy 2.38 and 5.48 times that for the Rh-N(Py) and Rh-N(Pym) bonds, respectively.     

Nd_2(Fe_(1-x)Co_x)_(14)B和Y_2(Fe_(1-x)Co_x)_(14)B的磁性

用磁测量和X-射线衍射研究了Nd_2(Fe_(1-x)Cox)_(14)B和Y_2(Fe_(1-x)Cox)_(14)B的晶格结构和内禀磁性。结果表明,低温下当钴含量较少时,Y_2(Fe_(1x)Cox)_(14)B的磁晶格向异性随钴含量的增加而增加,在1.5K和150K温度下,分别在x为0.4和0.2左右时磁晶各向异性常数达到极大;室温时的磁晶各向异性常数却随钴含量的增加而单调下降。用钴代换铁,对Nd_2(Fe_(1-x)Cox)_(14)B的自旋再取向温度的影响是复杂的。1.5K的饱和磁化强度在x=0.1左右达到极大。钴可以显著提高居里温度,对于Nd_2(Fe_(1-x)Cox)_(14)B和Y_2(Fe_(1-x)Cox)_(14)B,钴的作用几乎相同,表明居里温度主要由3d过渡金属原子之间的交换作用决定。     

New access to (η(5)-cyclohexadienyl)Mn(CO)3 and cationic (η(6)-arene)Mn(CO)3 complexes by Suzuki-Miyaura reaction

First Suzuki-Miyaura coupling reactions applied to (η(5)-chloro-cyclohexadienyl)Mn(CO)3 complexes are described and lead to the syntheses of (η(5)-aryl-cyclohexadienyl)Mn(CO)3 and of cationic (η(6)-arene)Mn(CO)3 complexes after rearomatization. The structures of two of the new complexes have been investigated by X-ray diffraction study.     

~(13)C核磁共振(六)

分子式为C_6H_8O的哪一个化合物与图E-11符合? 取谱条件: 溶剂:CDCl_3(δ77.2三重峰) 浓度:50V/V％温度:28℃测定频率:22.63MHz 去偶:上——~1H偏共振去偶(500次) 下——~1H宽带去偶(100次) [解答]C_6H_8O含有三个双键当量。在~(13)C谱中找到一个羰基(δ198.65)以及一个C=C键(δ150.6及129.85)。还余下一个双键与三个次甲基(δ38.2,25.75及22.95)。总结起     

OH(3) (-) and O(2)H(5) (-) double Rydberg anions: predictions and comparisons with NH(4) (-) and N(2)H(7) (-)

A low barrier in the reaction pathway between the double Rydberg isomer of OH(3) (-) and a hydride-water complex indicates that the former species is more difficult to isolate and characterize through anion photoelectron spectroscopy than the well known double Rydberg anion (DRA), tetrahedral NH(4) (-). Electron propagator calculations of vertical electron detachment energies (VEDEs) and isosurface plots of the electron localization function disclose that the transition state's electronic structure more closely resembles that of the DRA than that of the hydride-water complex. Possible stabilization of the OH(3) (-) DRA through hydrogen bonding or ion-dipole interactions is examined through calculations on O(2)H(5) (-) species. Three O(2)H(5) (-) minima with H(-)(H(2)O)(2), hydrogen-bridged, and DRA-molecule structures resemble previously discovered N(2)H(7) (-) species and have well separated VEDEs that may be observable in anion photoelectron spectra.     

Mixed ligand titanium(IV) complexes. Chlorobis(dithiocarbamato)bis(methylsalicylato)titanium(IV) andbis(dithiocarbamato)bis(methylsalicylato)titanium(IV)

Summary Dichlorobis(methylsalicylato)titanium(IV) reacts with potassium or amine salts of dialkyl or diaryl dithiocarbamates in 11 and 12 molar ratios in anhydrous benzene (room temperature) or in boiling CH₂Cl₂ to yield mixed ligand complexes: (AcOC₆H₄O)₂ Ti(S₂CNR₂)Cl (1) and (AcOC₆H₄O)₂ Ti(S₂CNR₂)₂ (2), R=Et, n-Pr, n-Bu, cyclo-C₄H₈ and cyclo-C₅H₁₀. These compounds are moisture sensitive and highly soluble in polar solvents. Molecular weight measurement in conjunction with i.r.,¹H and¹³C n.m.r. spectral studies suggest coordination number 7 and 8 around titanium(IV) in (1) and (2) respectively.     

Bis(trifluoroacetyl) peroxide, CF(3)C(O)OOC(O)CF(3)

Pure, highly explosive CF(3)C(O)OOC(O)CF(3) is prepared for the first time by low-temperature reaction between CF(3)C(O)Cl and Na(2)O(2). At room temperature CF(3)C(O)OOC(O)CF(3) is stable for days in the liquid or gaseous state. The melting point is -37.5 degrees C, and the boiling point is extrapolated to 44 degrees C from the vapor pressure curve log p = -1875/T + 8.92 (p/mbar, T/K). Above room temperature the first-order unimolecular decay into C(2)F(6) + CO(2) occurs with an activation energy of 129 kJ mol(-1). CF(3)C(O)OOC(O)CF(3) is a clean source for CF(3) radicals as demonstrated by matrix-isolation experiments. The pure compound is characterized by NMR, vibrational, and UV spectroscopy. The geometric structure is determined by gas electron diffraction and quantum chemical calculations (HF, B3PW91, B3LYP, and MP2 with 6-31G basis sets). The molecule possesses syn-syn conformation (both C=O bonds synperiplanar to the O-O bond) with O-O = 1.426(10) A and dihedral angle phi(C-O-O-C) = 86.5(32) degrees. The density functional calculations reproduce the experimental structure very well.