New methods for the direct determination of dissolved inorganic, organic and total carbon in natural waters by Reagent-Free Ion Chromatography and inductively coupled plasma atomic emission spectrometry

New methods have been developed and applied successfully for the determination of dissolved inorganic, organic and total carbon in water samples. The new methods utilize two instrumental setups, Reagent-Free™ Ion Chromatography (RF™-IC) and inductively coupled plasma atomic emission spectrometry (ICP-AES). Dissolved inorganic carbon (DIC) was measured in untreated samples along with Cl⁻, F⁻ and SO₄²⁻ using RF™-IC and by in-line mixing with 0.1 M HNO₃ to enhance CO₂ removal in the nebulizer, followed by ICP-AES analysis. Total dissolved carbon (TDC) was measured by in-line mixing with 0.1 M NaOH following ICP-AES analysis. Dissolved organic carbon (DOC) was obtained as the difference between DIC and TDC. Only non-volatile organic carbon could be detected by the present method. The workable limits of detection obtained in the present study were 0.5 mM (RF™-IC) and 0.1 mM (ICP-AES) for dissolved inorganic and organic carbon, respectively. The power of the new methods lies in routine analysis of DIC and DOC in samples of natural waters of variable composition and salinity using analytical techniques and facilities available in most laboratories doing water sample analysis. The techniques are sensitive and precise, can be automated using gas-tight sample vials and auto-samplers, and are independent of most elemental interferences with the exception of chloride overload by saline samples when using RF™-IC. The new methods were successfully applied for analysis of DIC and DOC in selected samples of natural and synthetic waters.     

Development of novel and sensitive methods for the determination of sulfide in aqueous samples by hydrogen sulfide generation-inductively coupled plasma-atomic emission spectroscopy

Two new, simple and accurate methods for the determination of sulfide (S²⁻) at low levels (μg L⁻¹) in aqueous samples were developed. The generation of hydrogen sulfide (H₂S) took place in a coil where sulfide reacted with hydrochloric acid. The resulting H₂S was then introduced as a vapor into an inductively coupled plasma-atomic emission spectrometer (ICP-AES) and sulfur emission intensity was measured at 180.669 nm. In comparison to when aqueous sulfide was introduced, the introduction of sulfur as H₂S enhanced the sulfur signal emission. By setting a gas separator at the end of the reaction coil, reduced sulfur species in the form of H₂S were removed from the water matrix, thus, interferences could be avoided. Alternatively, the gas separator was replaced by a nebulizer/spray chamber combination to introduce the sample matrix and reagents into the plasma. This methodology allowed the determination of both sulfide and sulfate in aqueous samples. For both methods the linear response was found to range from 5 μg L⁻¹ to 25 mg L⁻¹ of sulfide. Detection limits of 5 μg L⁻¹ and 6 μg L⁻¹ were obtained with and without the gas separator, respectively. These new methods were evaluated by comparison to the standard potentiometric method and were successfully applied to the analysis of reduced sulfur species in environmental waters.     

A green analytical procedure for flow-injection determination of nitrate in natural waters

Nitrate determination in waters is generally carried out with cadmium filings and carcinogenic reagents or by reaction with phenolic compounds in highly concentrated sulfuric acid medium. In this work, it was developed a green analytical procedure for nitrate determination in natural waters based on direct spectrophotometric measurements in ultraviolet, using a flow-injection system with an anion-exchange column for separation of nitrate from interfering species. The proposed method employs only one reagent (HClO₄) in a minimum amount (equivalent to 18 μL concentrated acid per determination), and allowed nitrate determination within 0.50-25.0 mg L⁻¹, without interference of up to 200.0 mg L⁻¹ humic acid; 1.0 mg L⁻¹ NO₂⁻; 200.0 mg L⁻¹ PO₄³⁻; 75.0 mg L⁻¹ Cl⁻; 50.0 mg L⁻¹ SO₄²⁻ and 15.0 mg L⁻¹ Fe³⁺. The detection limit (99.7% confidence level) and the coefficient of variation (n = 20) were estimated as 0.1 mg L⁻¹ and 0.7%, respectively. The results obtained for natural water samples were in agreement with those achieved by the reference method based on nitrate reduction with copperized cadmium at the 95% confidence level.     

Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2–. Using an electrolyte system with 9.5 mmol L^–1 potassium chromate as UV-absorbing probe and 1 mmol L^–1 diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2– were 0.35, 0.25, 0.78 and 0.80 mg L^–1, respectively. Received: 16 December 1999 / Revised: 7 March 2000 / Accepted: 14 March 2000     

Simple spectrophotometric method for the determination of sulfur dioxide by its decolorizing effect on the peroxovanadate complex

A simple, rapid, and economical spectrophotometric method is developed for the determination of sulfur dioxide in sugar and air samples. The developed method is based on a red-brown peroxovanadate complex (λ_max = 470 nm) produced in 2 M sulfuric acid when ammonium metavanadate is treated with hydrogen peroxide. Under fixed concentrations of hydrogen peroxide and ammonium metavanadate, when sodium metabisulfite (Na₂S₂O₅ = 2SO₂) is added, it preferentially reacts with hydrogen peroxide producing sulfuric acid, and the unreacted hydrogen peroxide then reacts with ammonium metavanadate; therefore, the concentration of sulfur dioxide is directly proportional to a decrease in the concentration of the peroxovanadate complex. The stoichiometric ratio between hydrogen peroxide and ammonium metavanadate as well as the stability constant of the complex are determined by the modified Job’s method and the respective values are found to be 1: 1 and 2.5 × 10⁴ mol⁻¹ L, respectively. The system obeys Lambert-Beer’s law in the concentration range 3.57–64.26 ppm of sulfur dioxide. The molar absorptivity, correlation coefficient, and Sandell’s sensitivity values are found to be 0.649 × 10³ L mol⁻¹ cm⁻¹, 0.9908, and 0.1972 μg cm⁻², respectively. The method is applied to the determination of sulfur dioxide present in commercial sugars and air samples. The results obtained are reproducible with a standard deviation of 0.02–0.05. For method validation, sulfur dioxide is also determined separately following the AOAC method for an air sample and the ICUMSA method for commercial sugars. The results obtained by the developed and official methods are in good agreement. The text was submitted by the authors in English.     

Determination of sulfur contents of SO3, S2O3 and S based on the electrocatalytic interaction with homogeneous mediator tris(2,2'-bipyridyl)Ru(II)

A sensitive voltammetric method has been developed for the determination of total or single species of sulfur anions containing sulfide, sulfite and thiosulfate. The method is based on the catalytic effect of tris(2,2'-bipyridyl)Ruthenium(II) (Ru(bpy)₂^+ 2) as a homogeneous mediator on the oxidation of those anions at the surface of a glassy carbon electrode. A reversible redox couple of Ru(II)/Ru(III) were observed as a solute in aqueous solution. Cyclic voltammetry study showed that the catalytic current of the system depends on the concentration of the anions. Optimum pH values for voltammetric determination of sulfite, thiosulfate and sulfide has been found to be 5.6, 10.0 and 10.0, respectively. Under the optimized conditions the calibration curves have been obtained linear in the concentration ranges of 0.8–500.0, 0.4–1000.0 and 0.5–5000.0 µmol L^− 1 of SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The detection limits have been calculated to be 0.40, 0.17 and 0.33 µmol L^− 1 for SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The diffusion coefficients of sulfite and thiosulfate have been estimated using chronoamperometry. The chronoamperometric method also has been used to determine the catalytic rate constant for catalytic reaction of the Ru(bpy)₂^+ 2 with sulfite and thiosulfate. Finally the proposed method has been used for the determination of total sulfur contents in real samples of water and wastewater. Moreover the sulfite content in sugar and sulfur dioxide in air has been determined with satisfactory results.     

A multi-pumping flow-based procedure with improved sensitivity for the spectrophotometric determination of acid-dissociable cyanide in natural waters

An analytical procedure with improved sensitivity was developed for cyanide determination in natural waters, exploiting the reaction with the complex of Cu(I) with 2,2′-biquinoline 4,4′-dicarboxylic acid (BCA). The flow system was based on the multi-pumping approach and long pathlength spectrophotometry with a flow cell based on a Teflon AF 2400^® liquid core waveguide was exploited to increase sensitivity. A linear response was achieved from 5 to 200 μg L⁻¹, with coefficient of variation of 1.5% (n = 10). The detection limit and the sampling rate were 2 μg L⁻¹ (99.7% confidence level), and 22 h⁻¹, respectively. Per determination, 48 ng of Cu(II), 5 μg of ascorbic acid and 0.9 μg of BCA were consumed. As high as 100 mg L⁻¹ thiocyanate, nitrite or sulfite did not affect cyanide determination. Sulfide did not interfere at concentrations lower than 40 and 200 μg L⁻¹ before or after sample pretreatment with hydrogen peroxide. The results for natural waters samples agreed with those obtained by a fluorimetric flow-based procedure at the 95% confidence level. The proposed procedure is then a reliable, fast and environmentally friendly alternative for cyanide determination in natural waters.     

An improved flow analysis-ion chromatography method for determination of cationic and anionic species at trace levels in Antarctic ice cores

A method was developed for the quantitative determination of cations and anions in Antarctic ice cores at μg L⁻¹ and sub-μg L⁻¹ levels by ion chromatography (IC), after ultra-clean decontamination procedures. Strict manipulation and decontamination procedures were used in sub-sampling, in order to minimise sample contamination. Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺ were determined by 12-min isocratic elution (H₂SO₄ eluent). Contemporaneously, in a parallel device, F⁻, MSA (methanesulfonic acid), Cl⁻, NO₃⁻ and SO₄²⁻ were analysed in a single 12-min run with multiple-step elution using Na₂CO₃/NaHCO₃ as eluent. Melted ice samples were pumped from their still-closed containers (polystyrene accuvettes with polyethylene caps), shared between the two ion chromatographic systems, online filtered (0.45 μm Teflon membrane) and pre-concentrated (anions and cations pre-concentration columns) using a flow analysis system, thus avoiding uptake of contaminants from the laboratory atmosphere. Sensitivity, linear range, reproducibility and detection limit were evaluated for each chemical species. Anion or cation detection limits ranged from 0.01 to 0.15 μg L⁻¹ by using a relatively small sample volume (1.5 mL). Such values are significantly lower than those reported in literature for almost all the components. These methods were successfully applied to the analysis of cations and anions at trace levels in the Dome C ice core. The composition of the atmospheric aerosol for the last 850 kyr was reconstructed by high-resolution continuous chemical stratigraphies. Concentration trends in the last nine glacial-interglacial climatic cycles were shown and briefly discussed.     

Ultra-sensitive DNA assay based on single-molecule detection coupled with fluorescent quantum dot-labeling and its application to determination of messenger RNA

Rapid, inexpensive, and convenient methods for quantifying elemental sulfur (S⁰) with low or sub-μg g⁻¹ limits of detection would be useful for a range of applications where S⁰ can act as a precursor for noxious off-aromas, e.g., S⁰ in pesticide residues on winegrapes or as a contaminant in drywall. However, existing quantification methods rely on toxic reagents, expensive and cumbersome equipment, or demonstrate poor selectivity. We have developed and optimized an inexpensive, rapid method (∼15 min per sample) for quantifying S⁰ in complex matrices. Following dispersion of the sample in PEG-400 and buffering, S⁰ is quantitatively reduced to H₂S in situ by dithiothreitol and simultaneously quantified by commercially available colorimetric H₂S detection tubes. By employing multiple tubes, the method demonstrated linearity from 0.03 to 100 μg S⁰ g⁻¹ for a 5 g sample (R² = 0.994, mean CV = 6.4%), and the methodological detection limit was 0.01 μg S⁰ g⁻¹. Interferences from sulfite or sulfate were not observed. Mean recovery of an S⁰ containing sulfur fungicide in grape macerate was 84.7% with a mean CV of 10.4%. Mean recovery of S⁰ in a colloidal sulfur preparation from a drywall matrix was 106.6% with a mean CV of 6.9%. Comparable methodological detection limits, sensitivity, and recoveries were achieved in grape juice, grape macerate and with 1 g drywall samples, indicating that the methodology should be robust across a range of complex matrices.     

Ion Chromatographic Determination of Anions in Environmental Samples

Abstract

The use of ion-exchange chromatography with an IonPac AS 14 column, 3.5 mM Na₂CO₃/1.0 mM NaHCO₃ eluent and suppressed conductivity detection provides a simple, cost-effective, fast, accurate, and highly sensitive method for the determination of F^?, Cl^?, NO₂ ^?, Br^?, NO₃ ^?, PO₄ ^2?, SO₄ ^2?, and C₂O₄ ^2? at low μ/L levels in environmental samples. Data on sensitivity, selectivity, accuracy, and % relative standard deviation are described. The method is suitable for many environmental applications including atmospheric aerosols (exposed on cellulose, glass fiber, and quartz filters), rainwater, cloud water, potable- and non-potable waters, and carbonated waters. Dominant components of the aerosol were SO₄ ^2?, NO₃ ^?, and Cl^?. Rainwater, on the other hand, has relatively very low concentrations of these three species. The wide-spread concentration range for Cl^? in variety of water samples and the high concentrations for SO₄ ^2? in drinking water are striking. Determination of the anionic composition of carbonated waters revealed a considerable variation of the individual anions.     

Characteristics of subtractive anodic stripping voltammetry of Pb and Cd at silver and gold electrodes

Silver and gold electrodes are useful for the quantitative determination of lead and cadmium with subtractive anodic stripping voltammetry (SASV). The use of SASV is essential for achieving good separation between the two peaks, to eliminate the interference of nitrates when cadmium is present and to allow analysis at very low concentrations without the removal of oxygen. The deposition and dissolution of Pb²⁺ and Cd²⁺ proceed at underpotential (UPD) on both electrodes. The UPD properties of the deposits are the main factor determining the analytical characteristics of the ASV method and are strongly affected by the type and concentration of the electrolyte. The effects of anions (Cl⁻, Br⁻, SO₄²⁻, NO₃⁻) and acids (HNO₃, HClO₄, H₂SO₄, HCl) are shown. The two electrodes complement each other and, in addition, enable the qualitative identification of Pb²⁺ and Cd²⁺, since the peaks appear in opposite order on the two electrodes. Analysis of mixtures of the two analytes is restricted on gold but not on silver. At gold the two peaks overlap: (i) at concentrations of cadmium higher than 250 nM at deposition times greater than 30 s, (ii) in the presence of copper at concentrations higher than 1 μM, and (iii) in the presence of Triton X-100 at concentrations above 10 mg/l. The repeatability at 10 nM analyte is better than 2.5%. The detection limits for Pb²⁺ and Cd²⁺ at 120 s deposition time and 3500 rpm rotation rate are: dl_Pb/Ag=0.04 nM; dl_Cd/Ag=0.7 nM; dl_Pb/Au=0.1 nM; dl_Cd/Au=0.3 nM. The analysis of lead and cadmium in natural waters has been performed.     

Photometrische Sulfitbestimmung mit Trinitrobenzoesäure

SO₃ ^2? can be determined photometrically with trinitrobenzoic acid within 2 min. SO₄ ^2?, S₂O₃ ^2?, S^2? and S_xO₆ ^2? in concentrations up to 1 mMole/100 ml do not interfere. The limit of determination is 0.22 mg SO₃ ^2?/100 ml, the standard deviation for the determination of 7 mg SO₃ ^2? is ± 0.59 Rel.-%.     

Reversed flow injection spectrophotometric determination of chlorate

An interfacing has been developed to connect a spectrophotometer with a personal computer and used as a readout system for development of a simple, rapid and sensitive reversed flow injection (rFI) procedure for chlorate determination. The method is based on the oxidation of indigo carmine by chlorate ions in an acidic solution (dil. HCl) leading to the decrease in absorbance at 610 nm. The decrease in absorbance is directly related to the chlorate concentration present in the sample solutions. Optimum conditions for chlorate were examined. A linear calibration graph over the range of 0.1-0.5 mg L⁻¹ chlorate was established with the regression equation of Y = 104.5X + 1.0, r² = 0.9961 (n = 6). The detection limit (3σ) of 0.03 mg L⁻¹, the limit of quantitation (10σ) of 0.10 mg L⁻¹ and the RSD of 3.2% for 0.3 mg L⁻¹ chlorate (n = 11) together with a sample throughput of 92 h⁻¹ were obtained. The recovery of the added chlorate in spiked water samples was 98.5 ± 3.1%. Major interferences for chlorate determination were found to be BrO₃⁻, ClO₂⁻, ClO⁻ and IO₃⁻ which were overcome by using SO₃²⁻ (as Na₂SO₃) as masking agent. The method has been successfully applied for the determination of chlorate in spiked water samples with the minimum reagent consumption of 14.0 mL h⁻¹. Good agreement between the proposed rFIA and the reference methods was found verified by Student's t-test at 95% confidence level.     

Separation of Sulfur Species in Water by Co-Electroosmotic Capillary Electrophoresis with Direct and Indirect UV Detection

Co-electroosmotic capillary electrophoresis (co-CZE) with both direct and indirect UV detection was investigated for the separation of sulfur species. With direct UV detection, the separation of S₂O^2? ₃, S₂O^2? ₄ was possible using 20 mM phosphate electrolyte containing 0.75 mM tetradecyltrimethylammonium bromide (TTAB) and 15% acetonitrile. To obtain optimal peak shape and sensitivity using indirect UV detection, a range of background electrolytes (BGEs), including benzoate, phthalate, 2,6-pyridinedicarboxylate (2,6-PDCA) and trimellitate, were examined as the BGEs. Of all the BGEs, 2,6-PDCA gave high selectivity and indirect UV response due to its mobility matching to that of sulfur species and its high absorptivity. Detection limits in range of 3-6 μM were obtained using either direct UV or indirect UV detection. The proposed CZE methods were used for the determination of sulfur species in water samples, and provided fast separation of sulfur species in less than 5 min.     

Development of an on-line preconcentration system for zinc determination in biological samples

An on-line preconcentration system for zinc determination in 24-h urine, blood plasma and erythrocyte matrices by flame atomic absorption spectrometry (FAAS) was used. This procedure was based on adsorption of Zn(II) ions onto a minicolumn filled with silica gel, chemically modified with niobium(V) oxide (Nb₂O₅-SiO₂). The determination of the optimum conditions for Zn(II) preconcentration was done using two-level full factorial and Doehlert designs. In the optimization procedure, four variables (sample pH, eluent concentration, sample flow rate and eluent flow rate) were investigated. The results obtained from the full factorial design demonstrated that the sample pH and sample flow rate variables, and their interactions, were statistically significant. A Doehlert matrix was used in order to determine the optimum conditions for the sample pH and sample flow rate. The optimized conditions for sample pH and flow rate sampling were 6.6 and 7.1 ml min⁻¹, respectively, to obtain the maximum Zn(II) preconcentration and determination in the biological samples studied. Parameters of analytical curve, precision, effect of other ions in the proposed system and accuracy were achieved to assess the proposed method. The accuracy was confirmed by analysis of certified reference materials (urine Seronorm™ Trace Elements) and recovery tests in blood plasma and erythrocyte samples. Detection limit (3σ/S) of 0.77 μg l⁻¹, precision (calculated as relative standard deviation) of 1.5% for Zn(II) concentration of 10 μg l⁻¹ (n = 7) and a sampling frequency of 27 samples/h were obtained from the proposed system.     

Determination of sulfur forms in wine including free and total sulfur dioxide based on molecular absorption of carbon monosulfide in the air–acetylene flame

A new method for the determination of sulfur forms in wine, i.e., free SO₂, total SO₂, bound SO₂, total S, and sulfate, is presented. The method is based on the measurement of the carbon monosulfide (CS) molecular absorption produced in a conventional air–acetylene flame using high-resolution continuum source absorption spectrometry. Individual sulfur forms can be distinguished because of the different sensitivities of the corresponding CS molecular absorption. The sensitivity of free SO₂ is about three times higher than the value for bound SO₂ and sulfate. The method makes use of procedures similar to those used in classic reference methods. Its performance is verified by analyzing six wine samples. Relative standard deviations are between 5 and 13% for free SO₂ and between 1 and 3% for total SO₂. For the validation of the accuracy of the new method, the results are compared with those of reference methods. The agreement of the values for total SO₂ with values of the classic method is satisfactory: five out of six samples show deviations less than 16%. Due to the instability of free SO₂ in wine and the known problems of the used reference method, serious deviations of the free SO₂ results are found for three samples. The evaluation of the limits of detection focuses on the value for free SO₂, which is the sulfur form having by far the lowest concentration in wine. Here, the achievable limit of detection is 1.8 mg L⁻¹. Figure Detection of non-metal elements using continuum source flame absorption spectrometry     

Derivatized humic acids modified gold electrode: electrochemical characterization and analytical applications

The preparation and application of a humic acids modified gold electrode (HA-CME) have been described. Derivatization of HAs as β-thioesters caused their partial fragmentation and, thus, a consequent separation by size exclusion chromatography (SEC) was necessary.The CME prepared with functionalized HAs having an average MW of 52000 demonstrated to be effective for trace As(III) determination (LOQ = 0.3 μg L⁻¹). This CME has been characterized both by electrochemical techniques and atomic force microscopy (AFM). The HA-CME provided reliable measurements in natural waters at different salinity with no need of desalting the sample. Total inorganic arsenic could be determined after reduction of As(V) with SO₂. Under these conditions, organic arsenic species were not mineralized and did not interfere.     

Development of a new method for sulfide determination by vapor generator–inductively coupled plasma–mass spectrometry

A new sensitive methodology for the determination of total reduced sulfur species in natural waters and acid volatile sulfides in sediments at low levels (μg L^− 1) is described. Reduced sulfur species were separated from the water matrix in the form of H₂S after reaction with hydrochloric acid in a commercial vapor generator coupled to an inductively coupled plasma quadrupole mass spectrometer (VG–ICP–QMS) equipped with a reaction cell. The method avoided the effect of polyatomic isobaric interferences at m/z 32 caused by ¹⁶O¹⁶O⁺ and ¹⁴N¹⁸O⁺ through the elimination of the aqueous matrix, a source of oxygen. By introducing a mixture of helium and hydrogen gases into the octopole reaction cell, a series of ion-molecule reactions were induced to reduce the interfering polyatomic species. Operating conditions of the octopole reaction cell system and the analyzer were optimized to get the best signal to background ratio for ³²S; a full factorial 2³ experimental design was developed in order to evaluate which variables had a significant effect and a simplex methodology was applied to find the optimum conditions for the variables. The new method was evaluated by comparison to the standard potentiometric method. The analytical methodology developed was applied to the analysis of reduced sulfur species in natural waters and acid volatile sulfides in sea sediments.     

Microflow injection chemiluminescence system with spiral microchannel for the determination of cisplatin in human serum

A new microflow injection chemiluminescence (μFI-CL) system was described for the determination of cisplatin in human serum. By using the microchip with double spiral channel configuration, the sensitivity was greatly enhanced due to more efficient mixing of the analyte and reagent solutions. Experimental results revealed that common ions in human serum, such as Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Ni²⁺, Na⁺, K⁺, Ca²⁺, Cl⁻, NO₃⁻, Ac⁻, CO₃²⁻, PO₄³⁻, SO₄²⁻ did not cause interference with the detection of Pt(II) by using 1,10-phenanthroline as the masking agent. Under the optimized conditions, a linear calibration curve (R² = 0.998) over the range 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ was obtained with the detection limit of 1.24 × 10⁻⁹ mol L⁻¹. The relative standard deviation was found to be 3.46% (n = 12) for 2.0 × 10⁻⁷ mol L⁻¹. The sample consumption was only 2 μL with the sample throughput of 72 h⁻¹. It had been used for trace platinum determination in cisplatin injection and human serum samples after the dosage of cisplatin. The recovery varied from 97.6 to 103.9%. The results proved that the proposed μFI-CL system had the advantages of high sensitivity and precision, low sample and reagents consumption, and high analytical throughput.     

A very sensitive flow system for the direct determination of copper in natural waters based on spectrophotometric detection

A very sensitive flow injection method with spectrophotometric detection has been developed for the on-line determination of copper in natural waters. The method exhibits a limit of detection three times lower than the most sensitive direct spectrophotometric method previously described and then allows the direct and simple in situ determination of copper in most natural waters.The method was based on the measurement of the absorbance of the coloured complex formed by copper with the chromogenic reagent di-2-pyridyl ketone benzoylhydrazone (dPKBH) in an alkaline medium. This complex presents stoichiometry 1:2 (Cu:dPKBH), and exhibits maximum absorbance at 370 nm. The manifold used was very simple, and consisted of two channels. The first one contained the sample while the second one contained the colorimetric reagent (3.3×10⁻⁴ M dPKBH in 10% ethanol), in a 1.6×10⁻² M phosphate buffer solution at pH 8. The performance of the system was optimised by using both univariate and modified simplex methodologies. When modified simplex was used, the best signal was obtained for a sample injection volume of 529 μl, a reaction coil length of 1.29 m, and a reagent flow rate of 4.8 ml min⁻¹. Under optimum conditions, the response was linear up to 3 mg l⁻¹ copper, the equation of the straight line being y=0.314x+5.2×10⁻⁴ (r²=0.998). The method allowed a sampling frequency of 40 samples per hour and exhibited a precision of 2.11% (as R.S.D., n=11). The limit of detection was 4.6 μg l⁻¹ (calculated as 3s_b/m, where s_b is the standard deviation of the y-intercept and m represents the slope of the straight line), and was therefore more sensitive than all the direct continuous methods reported previously.The method was successfully applied to the analysis of real water samples, with an average relative error of 5.32%.