Effect of side‐chain positions on morphology and photovoltaic properties of phenazine‐based donor–acceptor copolymers

Two phenazine donor–acceptor‐conjugated copolymers (P1 and P2) with the same polymer backbone but different anchoring positions of alkoxy chain on the phenazine unit were investigated to identify the effect of changing the position of alkoxy chains on their optical, electrochemical, blend film morphology, and photovoltaic properties. Although the optical absorption and frontier orbital energy levels were insensitive to the position of alkoxy chains, the film morphologies and photovoltaic performances changed significantly. P1/PC₇₁BM blend film showed the formation of phase separation with large coarse aggregates, whereas P2/PC₇₁BM blend film was homogeneous and smooth. Accordingly, power conversion efficiency (PCE) of photovoltaic devices increased from 1.50% for P1 to 2.54% for P2. In addition, the PCE of the polymer solar cell based on P2/PC₇₁BM blend film could be further improved to 3.49% by using solvent vapor annealing treatment. These results clearly revealed that tuning the side‐chain position could be an effective way to adjust the morphology of the active layer and the efficiency of the photovoltaic device. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2910–2918     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Quinoxaline‐based D‐A conjugated polymers for organic solar cells: Probing the effect of quinoxaline side chains and fluorine substitution on the power conversion efficiency

We describe the successful synthesis of four novel donor‐acceptor (D‐A) type copolymers, referred to as PQxBT , PQxFBT , TQxBT , and TQxFBT . The effects of using a fluorinated bithiophene (FBT) and varying the side‐chain moieties tethered to the quinoxaline (Qx) unit (electron‐withdrawing group in the polymer backbone) on the physical properties and photovoltaic performance were investigated. Specifically, the four polymers were synthesized using either alkoxyphenyl (P) or alkylthiophene (T) units anchored to the quinoxaline in the polymer backbone. The FBT‐bearing polymers, PQxFBT and TQxFBT , displayed more redshifted absorption spectra and higher crystallinity owing to the greater planarity of their polymer backbone as compared to the non‐fluorinated polymers. The TQxFBT copolymer, equipped with both the alkylthiophene side chains and FBT, exhibited face‐on orientation in film state and a well‐mixed nanophase morphology in TQxFBT :PC₇₁BM blend films. The photovoltaic device fabricated from TQxFBT :PC₇₁BM exhibited the highest power conversion efficiency of 4.18%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1209–1218     

Dithienosilole–phenylquinoxaline‐based copolymers with A‐D‐A‐D and A‐D structures for polymer solar cells

Two copolymers having D‐A‐D‐A ( P1 ) and D‐A ( P2 ) structures with quinoxaline acceptor unit and dithienosilole donor unit were synthesized and their optical and electrochemical (both experimental and theoretical) properties were investigated. The optical properties showed that these copolymers P1 and P2 exhibit optical bandgaps of 1.54 and 1.62 eV, respectively, with broader absorption profiles extending up to 800 nm and 770 nm, respectively. The electrochemical investigation of these two copolymers indicates that they exhibit suitable highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels for efficient exciton dissociation and high open circuit voltage in the resultant polymer solar cells (PSCs). These copolymers were used as donors along with the PC₇₁BM as acceptor for the fabrication of solution processed bulk heterojunction PSCs. The optimized P1 :PC₇₁BM and P2 :PC₇₁BM active layers treated with solvent vapor treatment showed overall power conversion efficiency (PCE) of 7.16% and 6.57%, respectively. The higher PCE of P1 ‐based device as compared to P2 might be attributed to higher crystallinity of P1 and good hole mobility resulting more balanced charge transport. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 376–386     

Silole‐containing polymers for high‐efficiency polymer solar cells

Silole‐containing conjugated polymers ( P1 and P2 ) carrying methyl and octyl substituents, respectively, on the silicon atom were synthesized by Suzuki polycondensation. They show strong absorption in the region of 300–700 nm with a band gap of about 1.9 eV. The two silole‐containing conjugated polymers were used to fabricate polymer solar cells by blending with PC₆₁BM and PC₇₁BM as the active layer. The best performance of photovoltaic devices based on P1 /PC₇₁BM active layer exhibited power conversion efficiency (PCE) of 2.72%, whereas that of the photovoltaic cells fabricated with P2 /PC₇₁BM exhibited PCE of 5.08%. 1,8‐Diiodooctane was used as an additive to adjust the morphology of the active layer during the device optimization. PCE of devices based on P2 /PC₇₁BM was further improved to 6.05% when a TiO_x layer was used as a hole‐blocking layer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and applications of cyano‐vinylene‐based polymers containing cyclopentadithiophene and dithienosilole units for photovoltaic cells

Two β‐cyano‐thiophenevinylene‐based polymers containing cyclopentadithiophene ( CPDT‐CN ) and dithienosilole ( DTS‐CN ) units were synthesized via Stille coupling reaction with Pd(PPh₃)₄ as a catalyst. The effects of the bridged atoms (C and Si) and cyano‐vinylene groups on their thermal, optical, electrochemical, charge transporting, and photovoltaic properties were investigated. Both polymers possessed the highest occupied molecular orbital (HOMO) levels of about ?5.30 eV and the lowest unoccupied molecular orbital (LUMO) levels of about ?3.60 eV, and covered broad absorption ranges with narrow optical band gaps (ca. 1.6 eV). The bulk heterojunction polymer solar cell (PSC) devices containing an active layer of electron‐donor polymers ( CPDT‐CN and DTS‐CN ) blended with an electron‐acceptor, that is, [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM), in different weight ratios were explored under 100 mW/cm² of AM 1.5 white‐light illumination. The PSC device based on DTS‐CN: PC₇₁BM (1:2 w/w) exhibited a best power conversion efficiency (PCE) value of 2.25% with V_oc = 0.74 V, J_sc = 8.39 mA/cm², and FF = 0.36. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Tailorable PC71BM Isomers: Using the Most Prevalent Electron Acceptor to Obtain High‐Performance Polymer Solar Cells

Despite being widely used as electron acceptor in polymer solar cells, commercially available PC₇₁BM (phenyl‐C₇₁‐butyric acid methyl ester) usually has a “random” composition of mixed regioisomers or stereoisomers. Here PC₇₁BM has been isolated into three typical isomers, α‐, β₁‐ and β₂‐PC₇₁BM, to establish the isomer‐dependent photovoltaic performance on changing the ternary composition of α‐, β₁‐ and β₂‐PC₇₁BM. Mixing the isomers in a ratio of α/β₁/β₂=8:1:1 resulted in the best power conversion efficiency (PCE) of 7.67 % for the polymer solar cells with PTB7:PC₇₁BM as photoactive layer (PTB7=poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]]). The three typical PC₇₁BM isomers, even though sharing similar LUMO energy levels and light absorption, render starkly different photovoltaic performances with average‐performing PCE of 1.28–7.44 % due to diverse self‐aggregation of individual or mixed PC₇₁BM isomers in the otherwise same polymer solar cells.     

The phase behavior of a polymer‐fullerene bulk heterojunction system that contains bimolecular crystals

Polymer:fullerene blends have been widely studied as an inexpensive alternative to traditional silicon solar cells. Some polymer:fullerene blends, such as blends of poly(2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene (pBTTT) with phenyl‐c71‐butyric acid methyl ester (PC₇₁BM), form bimolecular crystals due to fullerene intercalation between the polymer side chains. Here we present the determination of the eutectic pBTTT:PC₇₁BM phase diagram using differential scanning calorimetry (DSC) and two‐dimensional grazing incidence X‐ray scattering (2D GIXS) with in‐situ thermal annealing. The phase diagram explains why the most efficient pBTTT:PC₇₁BM solar cells have 75–80 wt % PC₇₁BM since these blends lie in the center of the only room‐temperature phase region containing both electron‐conducting (PC₇₁BM) and hole‐conducting (bimolecular crystal) phases. We show that intercalation can be suppressed in 50:50 pBTTT:PC₇₁BM blends by using rapid thermal annealing to heat the blends above the eutectic temperature, which forces PC₇₁BM out of the bimolecular crystal, followed by quick cooling to kinetically trap the pure PC₇₁BM phase. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Alternating and Diblock Donor–Acceptor Conjugated Polymers Based on Diindeno[1,2‐b:2′,1′‐d]thiophene Structure: Synthesis,Characterization, and Photovoltaic Applications

Pentacyclic diindeno[1,2‐b:2′,1′‐d]thiophene ( DIDT ) unit is a rigid and coplanar conjugated molecule. To the best of our knowledge, this attractive molecule has never been incorporated into a polymer and thus its application in polymer solar cells has never been explored. For the first time, we report the detailed synthesis of the tetra‐alkylated DIDT molecule leading to its dibromo‐ and diboronic ester derivatives, which are the key monomers for preparation of DIDT ‐based polymers. Two donor–acceptor alternating polymers, poly(diindenothiophene‐alt‐benzothiadiazole) PDIDTBT and poly(diindenothiophene‐alt‐dithienylbenzothiadiazole) PDIDTDTBT , were synthesized by using Suzuki polymerization. Copolymer PTDIDTTBT was also prepared by using Stille polymerization. Although PTDIDTTBT is prepared through a manner of random polymerization, we found that the different reactivities of the dibromo‐monomers lead to the resulting polymer having a block copolymer arrangement. With the higher structural regularity, PTDIDTTBT , symbolized as (thiophene‐alt‐ DIDT )_0.5‐block‐(thiophene‐alt‐BT)_0.5, shows the higher degree of crystallization, stronger π–π stacking, and broader absorption spectrum in the solid state, as compared to its alternating PDIDTDTBT analogue. Bulk heterojunction photovoltaic cells based on ITO/PEDOT:PSS/polymer:PC₇₁BM/Ca/Al configuration were fabricated and characterized. PDIDTDTBT /PC₇₁BM and PTDIDTTBT /PC₇₁BM systems exhibited promising power‐conversion efficiencies (PCEs) of 1.65 % and 2.00 %, respectively. Owing to the complementary absorption spectra, as well as the compatible structures of PDIDTDTBT and PTDIDTTBT , the PCE of the device based on the ternary blend PDIDTDTBT / PTDIDTTBT /PC₇₁BM was further improved to 2.40 %.     

Synthesis and applications of 2,7‐carbazole‐based conjugated main‐chain copolymers containing electron deficient bithiazole units for organic solar cells

A series of low‐band‐gap (LBG) donor–accepor conjugated main‐chain copolymers ( P1 – P4 ) containing planar 2,7‐carbazole as electron donors and bithiazole units (4,4′‐dihexyl‐2,2′‐bithiazole and 4,4′‐dihexyl‐5,5′‐di(thiophen‐2‐yl)‐2,2′‐bithiazole) as electron acceptors were synthesized and studied for the applications in bulk heterojunction (BHJ) solar cells. The effects of electron deficient bithiazole units on the thermal, optical, electrochemical, and photovoltaic (PV) properties of these LBG copolymers were investigated. Absorption spectra revealed that polymers P1 – P4 exhibited broad absorption bands in UV and visible regions from 300 to 600 nm with optical band gaps in the range of 1.93–1.99 eV, which overlapped with the major region of the solar emission spectrum. Moreover, carbazole‐based polymers P1 – P4 showed low values of the highest occupied molecular orbital (HOMO) levels, which provided good air stability and high open circuit voltages (V_oc) in the PV applications. The BHJ PV devices were fabricated using polymers P1 – P4 as electron donors and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or (6,6)‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as electron acceptors in different weight ratios. The PV device bearing an active layer of polymer blend P4:PC₇₁BM (1:1.5 w/w) showed the best power conversion efficiency value of 1.01% with a short circuit current density (J_sc) of 4.83 mA/cm², a fill factor (FF) of 35%, and V_oc = 0.60 V under 100 mW/cm² of AM 1.5 white‐light illumination. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Effect of Fluorination on the Photovoltaic Properties of Medium Bandgap Polymers for Polymer Solar Cells

Fluorination of conjugated polymers is one of the effective strategies to tune the molecular energy levels and morphology for high efficient polymer solar cells (PSCs). Herein, two novel donor‐acceptor conjugated polymers, PffBT and PBT, based on bis(3,5‐bis(hexyloxy)phenyl)benzo[1,2‐ b:4,5‐b']dithiophene and benzo[c][1,2,5]thiadiazole (BT) with or without fluorination, respectively, were synthesized, and their photovoltaic properties were compared. The polymer PffBT based on fluorinated BT showed lower frontier energy levels, improved polymer ordering, and a well‐developed fibril structure in the blend with PC₇₁BM. As a result, the PSCs based on PffBT/PC₇₁BM exhibit a superior power conversion efficiency (PCE) of 8.6% versus 4.4% for PBT‐based devices, due to a high space charge limit current (SCLC) hole mobility, mixed orientation of polymer crystals in the active layer, and low bimolecular recombination.     

Alternating copolymers incorporating cyclopenta[2,1‐b:3,4‐b′]dithiophene unit and organic dyes for photovoltaic applications

We have synthesized six p‐type copolymers, CPDT ‐ co ‐ TPADCN , CPDT ‐ co ‐ TPADTA , CPDT ‐ co ‐ TPATCN , CPDT ‐ co ‐ DFADCN , CPDT ‐ co ‐ DFADTA , and CPDT ‐ co ‐ DFATCN , consisting of a cyclopenta[2,1‐b:3,4‐b′]dithiophene (CPDT) unit and an organic dye in an alternating arrangement. Triphenylamine (TPA) or difluorenylphenyl amine (DFA) units serve as the electron donors, whereas dicyanovinyl (DCN), 1,3‐diethyl‐2‐thiobarbituric acid, or tricyanovinyl (TCN) units act as the electron acceptors in the dyes. The target polymers were prepared via Stille coupling, followed by postfunctionalization to introduce the electron acceptors to the side chains. Because of the strongest withdrawing ability of TCN acceptor to induce efficient intramolecular charge transfer, CPDT ‐ co ‐ TPATCN and CPDT ‐ co ‐ DFATCN exhibit the broader absorption spectra covering from 400 to 900 nm and the narrower optical band gaps of 1.34 eV. However, the CPDT ‐ co ‐ TPATCN :PC₇₁BM and CPDT ‐ co ‐ DFATCN :PC₇₁BM based solar cells showed the power conversion efficiencies (PCEs) of 0.22 and 0.31%, respectively, due to the inefficient exciton dissociation. The DFA‐based polymers possess deeper‐lying HOMO energy levels than the TPA‐based polymer analogues, leading to the higher V_oc values and better efficiencies. The device based on CPDT ‐ co ‐ DFADTA :PC₇₁BM blend achieved the best PCE of 1.38% with a V_oc of 0.7 V, a J_sc of 4.57 mA/cm², and a fill factor of 0.43. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Comprehensive study of pyrido[3,4‐b]pyrazine‐based D–π–a copolymer for efficient polymer solar cells

Two D–π–A copolymers, based on the benzo[1,2‐b:4,5‐b′]‐dithiophene (BDT) as a donor unit and benzo‐quinoxaline (BQ) or pyrido‐quinoxaline (PQ) analog as an acceptor (PBDT‐TBQ and PBDT‐TPQ), were designed and synthesized as a p‐type material for bulk heterojunction (BHJ) photovoltaic cells. When compared with the PBDT‐TBQ polymer, PBDT‐TPQ exhibits stronger intramolecular charge transfer, showing a broad absorption coverage at the red region and narrower optical bandgap of 1.69 eV with a relatively low‐lying HOMO energy level at ?5.24 eV. The experimental data show that the exciton dissociation efficiency of PBDT‐TPQ:PC₇₁BM blend is better than that in the PBDT‐TBQ:PC₇₁BM blend, which can explain that the IPCE spectra of the PBDT‐TPQ‐based solar cell were higher than that of the PBDT‐TBQ‐based solar cell. The maximum efficiency of PBDT‐TPQ‐based device reaches 4.40% which is much higher than 2.45% of PBDT‐TBQ, indicating that PQ unit is a promising electron‐acceptor moiety for BHJ solar cells. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1822–1833     

An Oligothiophene–Fullerene Molecule with a Balanced Donor–Acceptor Backbone for High‐Performance Single‐Component Organic Solar Cells

A new balanced donor–acceptor molecule, namely, benzodithiophene (BDT)‐rhodanine‐[6,6]‐phenyl‐C₇₁ butyric acid methyl ester (Rh‐PC₇₁BM) comprising two covalently linked blocks, a p‐type oligothiophene‐containing BDT‐based moiety and an n‐type PC₇₁BM unit was designed and synthesized. The single‐component organic solar cell (SCOSC) fabricated from Rh‐PC₇₁BM molecules showed a power conversion efficiency (PCE) of 3.22 % with an open‐circuit voltage (V_oc) of 0.98 V. These results rank are among the highest values for SCOSCs based on a monomolecular material. In particular, the one‐molecule Rh‐PC₇₁BM device exhibits excellent thermal stability compared to reference Rh‐OH:PC₇₁BM device. The success of our monomolecular strategy can provide a new way to develop high‐performance SCOSCs.     

Low‐bandgap quinoxaline‐based D–A‐type copolymers: Synthesis,characterization, and photovoltaic properties

Three classes of quinoxaline (Qx)‐based donor–acceptor (D–A)‐type copolymers, poly[thiophene‐2,5‐diyl‐alt‐2,3‐bis(4‐(octyloxy)phenyl‐quinoxaline‐5,8‐diyl] P(T‐Qx), poly{4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl‐alt‐2,3‐bis(4‐(octyloxy)phenyl‐quinoxaline‐5,8‐diy} P(BDT‐Qx), and poly{4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl‐alt‐(5′,8′‐di‐2‐thienyl‐2,3‐bis(4‐octyloxyl)phenyl)‐quinoxaline‐5,5‐diyl} P(BDT‐DTQx), were synthesized via a Stille coupling reaction. The Qx unit was functionalized at the 2‐ and 3‐positions with 4‐(octyloxy)phenyl to provide good solubility and to reduce the steric hindrance. The absorption spectra of the Qx‐containing copolymers could be tuned by incorporating three different electron‐donating moieties. Among these, P(T‐Qx) acted as an electron donor and yielded a high‐performance solar cell by assuming a rigid planar structure, confirmed by differential scanning calorimetry, UV–vis spectrophotometer, and density functional theory study. In contrast, the P(BDT‐Qx)‐based solar cell displayed a lower power conversion efficiency (PCE) with a large torsional angle (34.7°) between the BDT and Qx units. The BDT unit in the P(BDT‐DTQx) backbone acted as a linker and interfered with the formation of charge complexes or quinoidal electronic conformations in a polymer chain. The PCEs of the polymer solar cells based on these copolymers, in combination with [6,6]‐phenyl C70 butyric acid methyl ester (PC₇₁BM), were 3.3% [P(T‐Qx)], 1.9% [P(BDT‐Qx)], and 2.3% [P(BDT‐DTQx)], respectively, under AM 1.5G illumination (100 mW cm^?2). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Photovoltaic polymers based on difluoroqinoxaline units with deep HOMO levels

We report the synthesis of low bandgap polymers with a difluoroquinoxaline unit by Stille polymerization for use in polymer solar cells (PSCs). A new series of copolymers with 2,3‐didodecyl‐6,7‐difluoro quinoxaline as the electron‐deficient unit and alkyloxybenzo[1,2‐b:4,5‐b′]dithiophene and thiophene as the electron‐rich unit were synthesized. The photovoltaic properties of the devices based on the synthesized polymers revealed that the fluorine atoms at the quinoxaline units aid in decreasing the highest occupied molecular orbital (HOMO) energy levels; this in turn increased the open circuit voltage of the devices. The polymers with long alkyl chains exhibited good solubility that increased their molecular weight, but the power conversion efficiency was low. Efficient polymer solar cells were fabricated by blending the synthesized copolymers with PC₇₁BM, and the PCE increased up to 5.11% under 100 mW cm⁻² AM 1.5 illumination. These results demonstrate that the importance of having a control polymer to be synthesized and characterized side by side with the fluorine analogues. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1489–1497     

Synthesis and photovoltaic performances of benzo[1,2‐b:4,5‐b']dithiophene‐alt‐2,3‐diphenylquinoxaline copolymers pending functional groups in phenyl rings

Two donor/acceptor (D/A)‐based benzo[1,2‐b:4,5‐b′]dithiophene‐alt‐2,3‐biphenyl quinoxaline copolymers of P 1 and P 2 were synthesized pending different functional groups (thiophene or triphenylamine) in the 4‐positions of phenyl rings. Their thermal, photophysical, electrochemical, and photovoltaic properties, as well as morphology of their blending films were investigated. The poly(4,8‐bis((2‐ethyl‐hexyl)oxy)benzo[1,2‐b:4,5‐b'] dithiophene)‐alt‐(2,3‐bis(4′‐bis(N,N‐bis(4‐(octyloxy) phenylamino)‐ 1,1′‐biphen‐4‐yl)quinoxaline) ( P 2) exhibited better photovoltaic performance than poly(4,8‐bis((2‐ethylhexyl)oxy)benzo[1,2‐b:4,5‐b'] dithiophene)‐alt‐(2,3‐bis(4‐(5‐octylthiophen‐2‐yl)phenyl)quinoxaline) ( P 1) in the bulk‐heterojunction polymer solar cells with a configuration of ITO/PEDOT:PSS/polymers: [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)/LiF/Al. A power conversion efficiency of 3.43%, an open‐circuit voltage of 0.80 V, and a short‐circuit current of 9.20 mA cm^?2 were achieved in the P 2‐based cell under the illumination of AM 1.5, 100 mW cm^?2. Importantly, this power conversion efficiency level is 2.29 times higher than that in the P 1‐based cell. Our work indicated that incorporating triphenylamine pendant in the D/A‐based polymers can greatly improved the photovoltaic properties for its resulting polymers.     

The new low‐band gap polymers comprising C‐, Si‐, or N‐bridged dithiophene and alkoxy‐modified 2,1,3‐benzooxadiazole units for bulk heterojunction solar cells

In this study, we used Stille coupling polymerization to synthesize a series of new low‐band gap‐conjugated polymers— PCyTBO , PCySiTBO , and PCyNTBO —comprising mainly electron‐rich C‐, Si‐, and N‐bridged dithiophene units in conjugation with electron‐deficient alkoxy‐modified 2,1,3‐benzooxadiazole moieties. The highest occupied molecular orbital energy levels of these polymers become higher as the electron‐donating ability of C‐, Si‐, or N‐bridged dithiophene units increases. These polymers also displayed excellent thermal stability and broad spectral absorptions, with PCySiTBO revealing some crystallinity. As a result, the photovoltaic device incorporating the PCySiTBO /PC₇₁BM (1:1) blend system and 1,8‐diiodooctane (2 vol %) as an additive exhibited excellent performance, under AM 1.5 G irradiation (100 mW cm^?2), with a value of V_oc of 0.64 V, a short‐circuit current density of 13.8 mA cm^?2, a fill factor of 0.57, and a promising power conversion efficiency of 5.0%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

2,1,3‐benzothiadiazole‐5,6‐dicarboxylicimide based semicrystalline polymers for photovoltaic cells

Two semicrystalline low band gap polymers based on highly electron‐deficient 2,1,3‐benzothiadiazole‐5,6‐dicarboxylicimide (BTI) were synthesized by considering the chain planarity via intrachain noncovalent coulombic interactions. The thiophene‐BTI and thienothiophene‐BTI based PPDTBTI and PPDTTBTI have a low band gap (～1.5 eV) via strong intramolecular charge transfer interaction, showing a broad light absorption covering 300～850 nm. Semicrystalline film morphology was observed for both polymers in the grazing incidence wide angle X‐ray scattering measurements. Interestingly, PPDTBTI showed a pronounced edge on packing structure but PPDTTBTI showed predominantly a face on orientation in both pristine and blend films. Different packing patterns influenced significantly the charge carrier transport, recombination and resulting photovoltaic characteristics. The best power conversion efficiency was measured to be 5.47% for PPDTBTI and 6.78% for PPDTTBTI, by blending with the fullerene derivative, PC₇₁BM. Compared to the PPDTBTI blend, PPDTTBTI: PC₇₁BM suffered from the lower open‐circuit voltage but showed the substantially higher hole mobility and short‐circuit current density with smaller charge recombination, showing very good agreements with molecular structures and morphological characteristics. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3826–3834     

Control of vertical distribution of thiophene‐based copolymers containing 4,7‐Dithien‐2‐yl‐benzo[C][1,2,5]thiadiazole and 3,6‐Dithien‐2‐yl‐pyrrolo[3,4‐C]pyrrole‐1,4(2H,5H)‐dione as Side Groups for Photovoltaics

Four new D—A type copolymers with 2D‐conjugated side‐chain identified PfToBT, PbToBT, PfTDPP and PbTDPP, containing two acceptors 4,7‐dithien‐2‐yl‐benzo[c][1,2,5]thiadiazole (DTBT), and diketopyrrolopyrrole (DPP) linked by thiophene donors, are obtained using Pd‐catalyzed Stille‐coupling reaction. These polymers show a broad visible‐near‐infrared absorption band (E_g = 1.79–1.66 eV) and possess a relatively low‐lying HOMO level at ?5.34 to ?5.12 eV. All the polymer:PC₇₀BM blend films showed edge‐on structure and have similar d_π‐spacing values. According to the structure of conjugated side‐chain, the vertical distributions of polymer chains and PC₇₀BM within the BHJ (bulk heterojunction) were different. When DPP used as an acceptor, conjugated side chains of the polymer coexisted with PC₇₀BM in same position. The BHJ film prepared from PfToBT, PbToBT had a discontinuous network between polymer and PC₇₀BM, whereas films from PfTDPP and PbTDPP formed continuous and evenly distributed network between them. This optimized vertical morphology promotes hole transport along respective pathways of polymers and fullerenes in the vertical direction, leading to high J_SC. PbTDPP shows PCE up to 2.9% (Jsc of 9.4 mA/cm², Voc of 0.68 V, and FF of 0.44). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2746–2759