Renewable chain transfer agents for metallocene polymerizations: The effects of chiral monoterpenes on the polyolefin molecular weight and isotacticity

Monoterpenes were used as renewable chain transfer agents and polymerization solvents for metallocene/methylaluminoxane (MAO) catalysis. The polymerization of 1‐hexene, ethylene, and propylene in d‐limonene, hydrogenated d‐limonene and α‐pinene is reported. As detected by ¹H NMR analysis of the alkene region, chain transfer to d‐limonene yielded a higher percentage of trisubstituted alkenes. Size exclusion chromatography detected a decrease in molecular weight values resulting from chain transfer to d‐limonene. The [mmmm] pentads for isotactic polypropylene were characterized by ¹³C NMR and FTIR spectroscopy. Propylene polymerizations with the Et(Ind)₂ZrCl₂/MAO and Me₂Si(Ind)₂ZrCl₂/MAO catalyst systems in d‐limonene gave [mmmm] pentad values as high as 0.97. For the Et(Ind)₂ZrCl₂/MAO catalyst system at 0 °C, the mol fraction of [mmmm] pentads increased from 0.86 to 0.94 upon switching the solvent from toluene to d‐limonene. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3150–3165, 2007     

Homogeneous tandem catalysis of the bis‐(diphenylphosphino)‐amine/chromium tetramerization catalyst with metallocene catalysts

Homogeneous tandem catalysis of the bis(diphenylphoshino)amine‐chromium oligomerization catalyst with the metallocenes Ph₂C(Cp)(9‐Flu)ZrCl₂ and rac‐EtIn₂ZrCl₂, is discussed. GC, CRYSTAF, and ¹³C NMR analysis of the products obtained from reactions at constant temperatures show that during tandem catalysis, α‐olefins, mainly 1‐hexene and 1‐octene, are produced from ethylene by the oligomerization catalyst and subsequently built into the polyethylene chain. At 40 °C the Cr/PNP catalyst acts as a tetramerization catalyst while the polymerization catalyst activity is low. Copolymerization of ethylene and the in situ produced α‐olefins have also been carried out by increasing the temperature from 40 °C, where primarily oligomerization takes place, to above 100 °C, where polymerization becomes dominant. The melting temperature of the polymer is dependent on the catalyst and cocatalyst ratios as well as on the temperature gradient followed during the reaction, while the presence of the oligomerization catalyst reduces the activity of the polymerization catalyst. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6847–6856, 2006     

Copolymerization of vinylcyclohexane with ethene and propene using zirconocene catalysts

Vinylcyclohexane (VCH) was copolymerized with ethene and propene using methylaluminoxane‐activated metallocene catalysts. The catalyst precursor for the ethene copolymerization was rac‐ethylenebis(indenyl)ZrCl₂ ( 1 ). Propene copolymerizations were further studied with C_s‐symmetric isopropylidene(cyclopentadienyl)(fluorenyl)ZrCl₂ ( 2 ), C₁‐symmetric ethylene(1‐indenyl‐2‐phenyl‐2‐fluorenyl)ZrCl₂ ( 3 ), and “meso”‐dimethylsilyl[3‐benzylindenyl)(2‐methylbenz[e]indenyl)]ZrCl₂ ( 4 ). Catalyst 1 produced a random ethene–VCH copolymer with very high activity and moderate VCH incorporation. The highest comonomer content in the copolymer was 3.5 mol %. Catalysts 1 and 4 produced poly(propene‐co‐vinylcyclohexane) with moderate to good activities [up to 4900 and 15,400 kg of polymer/(mol of catalyst × h) for 1 and 4 , respectively] under similar reaction conditions but with fairly low comonomer contents (up to 1.0 and 2.0% for 1 and 4 , respectively). Catalysts 2 and 3 , both bearing a fluorenyl moiety, gave propene–VCH copolymers with only negligible amounts of the comonomer. The homopolymerization of VCH was performed with 1 as a reference, and low‐molar‐mass isotactic polyvinylcyclohexane with a low activity was obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6569–6574, 2006     

Comparison of the C1‐symmetric diastereoisomers of a zirconocene‐based catalyst in ethylene polymerization: A benzyl substituent as a regulator in branch formation

C₁‐symmetric diastereoisomers of a zirconocene dichloride, SiMe₂(3‐benzylindenyl)(indenyl)ZrCl₂, known as catalyst precursors used to produce polypropylenes with similar molecular weights and tacticities, have been investigated in ethylene polymerization. Activated by methylaluminoxane, they produce microstructurally different polymers: high‐density polyethylene and linear low‐density polyethylene, the latter characterized by the presence of ethyl branches. The formation of branches is relevant in the complex having a sterically more crowded (inward) site. A comparison with the complex without substituents, meso‐SiMe₂(indenyl)₂ZrCl₂, shows that the presence of a benzyl group on only one of the two indenyl moieties can regulate the number of branches and the molecular weight of the macromolecule. Actually, the unsubstituted complex is able to give double the number of branches and lower molecular weights, whereas the C₁‐symmetric disubstituted complexes previously reported generally give linear polyethylene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3551–3555, 2006     

Influence of the graphite type on the synthesis of polypropylene/graphene nanocomposites

In this work, the synthesis of polypropylene (PP)/graphene nanosheet (GNS) nanocomposites by in situ polymerization using metallocene catalysts was studied. Initial reactions were performed using rac‐Et(Ind)₂ZrCl₂ and rac‐Me₂Si(Ind)₂ZrCl₂ catalysts to select the best one to obtain good molecular weight, thermal properties, and tacticity. Subsequently, PP nanocomposites with different loadings of GNS were obtained. GNS from two different sources [Graphite Nacional (GN) and Graphite Aldrich (GA)] have been used, and the differences between the obtained nanocomposites were evaluated. The GNS and nanocomposites were studied by scanning electronic microcopy, transmission electronic microcopy, and X‐ray diffraction. They showed that the GN nanosheets had lower crystal size and diameter than the GA nanosheets and dispersed better in the PP matrix. Differential scanning calorimetry analyses of both types of nanocomposites showed an increase in the crystallization temperature with increasing graphite loading. The polymeric materials were also characterized by GPC, thermogravimetric analysis, and ¹³C NMR. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of a new zirconium catalyst for ethylene polymerization

A novel complex dichlorobis(2‐ethyl‐3‐hydroxy‐4‐pyrone)zirconium(IV) (ZrCl₂(ethylpyrone)₂) was synthesized. Complexation of the pyrone ligand to the zirconium was confirmed by UV, ¹H and ¹³C‐NMR, and electrochemical studies. NMR showed the presence of four isomers and density functional theory calculations indicated that the main isomer had a cis configuration. The catalyst was shown to be active in ethylene polymerization in the presence of the cocatalyst methylaluminoxane. The highest catalyst activity for the zirconium complex was achieved at Al/Zr = 2500, 70 °C and when a small concentration of catalyst was used (1 μmol). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3830–3841, 2008     

Synthesis and properties of high‐molecular‐weight stereo di‐block polylactides with nonequivalent D/L ratios

Di‐stereoblock polylactides (di‐sb‐PLA: PLLA‐b‐PDLA) having high molecular weight (M_n > 100 kDa) were successfully synthesized by two‐step ring‐opening polymerization (ROP) of L ‐ and D ‐lactides using tin(2‐ethylhexanoate) as a catalyst. By optimizing the polymerization conditions, the block sequences were well regulated at non‐equivalent feed ratios of PLLA and PDLA. This synthetic method consisted of three stages: (1) polymerization of either L ‐ or D ‐lactide to obtain a PLLA or PDLA prepolymer with a molecular weight less than 50 kDa, (2) purification of the obtained prepolymer to remove residual lactide, and (3) polymerization of the enantiomeric lactide in the presence of the purified prepolymer. Their ¹³C and ³¹P NMR spectra of the resultant di‐sb‐PLAs strongly supported their di‐stereo block structure. These di‐sb‐PLAs, having weight‐average molecular weights higher than 150 kDa, were fabricated into polymer films by solution casting and showed exclusive stereocomplexation. The thermomechanical analysis of the films revealed that their heat deformation temperature was limited probably because of their low crystallinity owing to the non‐equivalent PLLA/PDLA ratio. The blend systems of the di‐sb‐PLAs having complementary stereo‐sequences (the one with a long PLLA block and the other with long PDLA block) were also prepared and characterized to enhance the sc crystallinity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 794–801, 2010     

Stereospecific polymerization of 1‐hexene catalyzed by ansa‐metallocene/methylaluminoxane systems under high pressures

Stereospecific polymerization of 1‐hexene under high pressures (up to 1,000 MPa = ca. 10,000 atm) using metallocene/methylaluminoxane (MAO) catalysts was investigated. Several C₂‐symmetric ansa‐metallocenes, their meso‐isomers, and two C_s‐symmetric ansa‐metallocenes were employed as catalyst precursors. In the course of this study, novel C₂‐symmetric germylene‐bridged ansa‐metallocenes, (rac‐[Me₂Ge(η⁵‐C₅H‐2,3,5‐Me₃)₂MCl₂] (M = Zr, rac‐4a; M = Hf, rac‐4b), have been prepared. High pressures induced enhancement of the catalytic activity and the molecular weight of the polymers in most of the catalysts. The maximum of both the catalytic activity and the molecular weight of the polymers was mostly observed at 100–500 MPa in each catalyst, although the enhanced ratio was smaller than that observed for nonbridged metallocenes. Isospecificity of the C₂‐symmetric ansa‐metallocene catalysts was essentially maintained even under high pressure. Highly isotactic polyhexene ([mmmm] = 91.6%) with very high molecular weight (M_w = 2,360,000) was achieved by rac‐4b under 250 MPa. High pressures slightly decreased syndiotacticity when the C_s‐symmetric ansa‐metallocene, isopropylidene(1‐η⁵‐cyclopentadienyl)(9‐η⁵‐fluorenyl)zirconium dichloride 5, was employed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 283–292, 1999     

α‐keto‐β‐diimine nickel‐catalyzed olefin polymerization: Effect of ortho‐aryl substituents and preparation of stereoblock copolymers

A series of α‐keto‐β‐diimine nickel complexes (Ar‐N = C(CH₃)‐C(O)‐C(CH₃)=N‐Ar)NiBr₂; Ar = 2,6‐R‐C₆H₃‐, R = Me, Et, iPr, and Ar = 2,4,6‐Me₃‐C₆H₃‐) was prepared. All corresponding ligands are unstable even under an inert atmosphere and in a freezer. Stable copper complex intermediates of ligand synthesis and ethyl substituted nickel complex were isolated and characterized by X‐ray. All nickel complexes were used for the polymerization of ethene, propylene, and hex‐1‐ene to investigate their livingness and the extent of chain‐walking. Low‐temperature propene polymerization with less bulky ortho‐substituents was less isospecific than the one with isopropyl derivative. Propene stereoblock copolymers were prepared by iPr derivative combining the polymerization at low temperature to prepare isotactic polypropylene (PP) block and at a higher temperature, supporting chain‐walking, to obtain amorphous regioirregular PP block. Alternatively, a copolymerization of propene with ethene was used for the preparation of amorphous block. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2440–2449     

Influence of the catalyst and polymerization conditions on the long‐chain branching of metallocene‐catalyzed polyethenes

A study was made on the effects of polymerization conditions on the long‐chain branching, molecular weight, and end‐group types of polyethene produced with the metallocene‐catalyst systems Et[Ind]₂ZrCl₂/MAO, Et[IndH₄]₂ZrCl₂/MAO, and (n‐BuCp)₂ZrCl₂/MAO. Long‐chain branching in the polyethenes, as measured by dynamic rheometry, depended heavily on the catalyst and polymerization conditions. In a semibatch flow reactor, the level of branching in the polyethenes produced with Et[Ind]₂ZrCl₂/MAO increased as the ethene concentration decreased or the polymerization time increased. The introduction of hydrogen or comonomer suppressed branching. Under similar polymerization conditions, the two other catalyst systems, (n‐BuCp)₂ZrCl₂/MAO and Et[IndH₄]₂ZrCl₂/MAO, produced linear or only slightly branched polyethene. On the basis of an end‐group analysis by FTIR and molecular weight analysis by GPC, we concluded that a chain transfer to ethene was the prevailing termination mechanism with Et[Ind]₂ZrCl₂/MAO at 80 °C in toluene. For the other catalyst systems, β‐H elimination dominated at low ethene concentrations. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 376–388, 2000     

Synthesis of branched polypropylene with isotactic backbone and atactic side chains by binary iron and zirconium single‐site catalysts

This article reports the use of a binary single‐site catalyst system for synthesizing comb‐branched polypropylene samples having isotactic polypropylene (iPP) backbones and atactic polypropylene (aPP) side chains from propylene feedstock. This catalyst system consisted of the bisiminepyridine iron catalyst {[2‐ArN?C(Me)]₂C₅H₃N}FeCl₂ [Ar = 2,6‐C₆H₃(Me)₂] ( 1 ) and the zirconocene catalyst rac‐Me₂Si(2‐MeBenz[e]Ind)₂ZrCl₂ ( 2 ). The former in situ generated 1‐propenyl‐ended aPP macromonomer, whereas the latter incorporated the macromonomer into the copolymer. The effects of reaction conditions, such as the catalyst addition procedure and the ratio of 1 / 2 on the branching frequency, were examined. Copolymer samples having a branching density up to 8.6 aPP side chains per 1000 iPP monomer units were obtained. The branched copolymers were characterized by ¹³C NMR and differential scanning calorimetry. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1152–1159, 2003     

Borane chain transfer reaction in olefin polymerization using trialkylboranes as chain transfer agents

This article discusses a new borane chain transfer reaction in olefin polymerization that uses trialkylboranes as a chain transfer agent and thus can be realized in conventional single site polymerization processes under mild conditions. Commercially available triethylborane (TEB) and synthesized methyl‐B‐9‐borabicyclononane (Me‐B‐9‐BBN) were engaged in metallocene/MAO [depleted of trimethylaluminum (TMA)]‐catalyzed ethylene (Cp₂ZrCl₂ and rac‐Me₂Si(2‐Me‐4‐Ph)₂ZrCl₂ as a catalyst) and styrene (Cp*Ti(OMe)₃ as catalyst) polymerizations. The two trialkylboranes were found—in most cases—able to initiate an effective chain transfer reaction, which resulted in hydroxyl (OH)‐terminated PE and s‐PS polymers after an oxidative workup process, suggesting the formation of the B‐polymer bond at the polymer chain end. However, chain transfer efficiencies were influenced substantially by the steric hindrances of both the substituent on the trialkylborane and that on the catalyst ligand. TEB was more effective than TMA in ethylene polymerization with Cp₂ZrCl₂/MAO, whereas it became less effective when the catalyst changed to rac‐Me₂Si(2‐Me‐4‐Ph)₂ZrCl₂. Both TEB and Me‐B‐9‐BBN caused an efficient chain transfer in the Cp₂ZrCl₂/MAO‐catalyzed ethylene polymerization; nevertheless, Me‐B‐9‐BBN failed in vain with rac‐Me₂Si(2‐Me‐4‐Ph)₂ZrCl₂/MAO. In the case of styrene polymerization with Cp*Ti(OMe)₃/MAO, thanks to the large steric openness of the catalyst, TEB exhibited a high efficiency of chain transfer. Overall, trialkylboranes as chain transfer agents perform as well as B? H‐bearing borane derivatives, and are additionally advantaged by a much milder reaction condition, which further boosts their applicability in the preparation of borane‐terminated polyolefins. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3534–3541, 2010     

Highly active copolymerization of ethylene with 10‐undecen‐1‐ol using phenoxy‐based zirconium/methylaluminoxane catalysts

Activated with methylaluminoxane (MAO), phenoxy‐based zirconium complexes bis[(3‐^tBu‐C₆H₃‐2‐O)‐CH?NC₆H₅]ZrCl₂, bis[(3,5‐di‐^tBu‐C₆H₂‐2‐O)‐PhC?NC₆H₅] ZrCl₂, and bis[(3,5‐di‐^tBu‐C₆H₂‐2‐O)‐PhC?N(2‐F‐C₆H₄)]ZrCl₂ for the first time have been used for the copolymerization of ethylene with 10‐undecen‐1‐ol. In comparison with the conventional metallocene, the phenoxy‐based zirconium complexes exhibit much higher catalytic activities [>10⁷ g of polymer (mol of catalyst)^?1 h^?1]. The incorporation of 10‐undecen‐1‐ol into the copolymers and the properties of the copolymers are strongly affected by the catalyst structure. Among the three catalysts, complex c is the most favorable for preparing higher molecular weight functionalized polyethylene containing a higher content of hydroxyl groups. Studies on the polymerization conditions indicate that the incorporated commoner content in the copolymers mainly depends on the comonomer concentration in the feed. The catalytic activity is slightly affected by the Al_(MAO)/Zr molar ratio but decreases greatly with an increase in the polymerization temperature. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5944–5952, 2005     

Tacticity of poly‐α‐olefins from poly‐1‐hexene to poly‐1‐octadecene

A systematic study of the influence of the α‐olefin size, the catalyst stereospecificity and the reaction temperature was done on the catalytic activity and tacticity of poly‐α‐olefins from 1‐hexene to 1‐octadecene. The metallocenes used were rac‐Et[Ind₂]ZrCl₂ ( 1 ) and Me₂C[Cp(9‐Flu)]ZrCl₂ ( 2 ) to obtain isotactic and syndiotactic polyolefins. Some catalysts giving atactic polymers were also used in order to study all the possible ¹³C NMR pentades. Catalytic activities increased and isotacticity and syndiotacticity decreased with temperature, but no real trend was found with the α‐olefin size. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4744–4753, 2005     

Synthesis and characterization of ethylene‐propylene‐1‐pentene terpolymers

Ethylene (E), propylene (P), and 1‐pentene (A) terpolymers differing in monomer composition ratio were produced, using the metallocenes rac‐ethylene bis(indenyl) zirconium dichloride/methylaluminoxane (rac‐Et(Ind)₂ZrCl₂/MAO), isopropyl bis(cyclopentadienyl)fluorenyl zirconium dichloride/methylaluminoxane (Me₂C(Cp)(Flu)ZrCl₂/MAO, and bis(cyclopentadienyl)zirconium dichloride, supported on silica impregnated with MAO (Cp₂ZrCl₂/MAO/SiO₂/MAO) as catalytic systems. The catalytic activities at 25 °C and normal pressure were compared. The best result was obtained with the first catalyst. A detailed study of ¹³C NMR chemical shifts, triad sequences distributions, monomer‐average sequence lengths, and reactivity ratios for the terpolymers is presented. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 947–957, 2008     

Titanium and zirconium complexes containing modified TREN ligands for the polymerization of 1‐alkenes—A comparative study

The titanium and zirconium complexes in C₃ and C_s symmetric forms synthesized from corresponding aminotriols in combination with MAO polymerized 1‐hexene in a controlled manner. When the polymerization temperature was lowered, they gave high molecular weight monodisperse polyhexene with narrow polydispersities indicating quazi‐living systems. The isotactic polyhexene obtained from C₃ titanium catalyst has the molecular weight of around 46,500 with PDI of 1.3 and the hemi‐isotactic polymer from C_s titanium catalyst has the molecular weight of around 617,000 with PDI of 1.3. The analogues zirconium complexes upon activation with MAO polymerize hexene to give polyhexene having molecular weight of 53,000 (C₃) and 626,000 (pseudo‐C_s) with PDI ranging from 1.2 to 1.4. The MIX‐titanium catalyst prepared from the 50:50 mixture of aminotriols was also able to polymerize 1‐hexene and the GPC traces of the polyhexene suggests that even though the catalyst was formed from the mixture of aminotriols, the C₃ and C_s symmetry of the catalysts retain its originality avoiding the formation of aggregates or polymeric forms. When one of the arms of aminotriol was methylated yield C₂ and meso aminodiol ligands and their corresponding titanium and zirconium complexes gave higher molecular weight polyhexenes with lower PDI (C₂‐Zr‐M_n: 260,000; PDI: 1.05–1.10; mesoZr‐M_n: 220,000; PDI: 1.05–1.10) possibly suggesting that these systems are close to living systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5470–5479, 2007     

Polymerization of higher α‐olefins using a Cs‐symmetry hafnium metallocene catalyst. Kinetics of the polymerization and microstructural analysis

The C_s‐symmetry hafnium metallocene [(p‐Et₃Si)C₆H₄]₂C(2,7‐di‐tert‐BuFlu)(C₅H₄)Hf(CH₃)₂ and tetrakis(pentafluorophenyl) borate dimethylanilinium salt ([B(C₆F₅)₄]^?[Me₂NHPh]⁺) were used as the catalytic system for the polymerization of higher α‐olefins (from hexene‐1 to hexadecene‐1) in toluene at 0 °C. The evolution of the polymerization was studied regarding the variation of the molecular weight, molecular weight distribution and yield with time. The effect of the monomer structure on the polymerization kinetics was established. The role of trioctylaluminum in accelerating the polymerization was investigated. ¹³C NMR spectroscopy was used to study the microstructure of the poly(α‐olefins) by the determination of the pentad monomer sequences. The thermal properties of the polymers were obtained by differential scanning calorimetry, DSC. The results were discussed in connection with the polymer microstructure. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4314–4325, 2009     

Direct synthesis of linear low‐density polyethylene of ethylene/1‐hexene from ethylene with a tandem catalytic system in a single reactor

Tandem catalysis offers a promising synthetic route to the production of linear low‐density polyethylene. This article reports the use of homogeneous tandem catalytic systems for the synthesis of ethylene/1‐hexene copolymers from ethylene stock as the sole monomer. The reported catalytic systems employ the tandem action between an ethylene trimerization catalyst, (η⁵‐C₅H₄CMe₂C₆H₅)TiCl₃ ( 1 )/modified methylaluminoxane (MMAO), and a copolymerization metallocene catalyst, [(η⁵‐C₅Me₄)SiMe₂(^tBuN)]TiCl₂ ( 2 )/MMAO or rac‐Me₂Si(2‐MeBenz[e]Ind)₂ZrCl₂ ( 3 )/MMAO. During the reaction, 1 /MMAO in situ generates 1‐hexene with high activity and high selectivity, and simultaneously 2 /MMAO or 3 /MMAO copolymerizes ethylene with the produced 1‐hexene to generate butyl‐branched polyethylene. We have demonstrated that, by the simple manipulation of the catalyst molar ratio and polymerization conditions, a series of branched polyethylenes with melting temperatures of 60–128 °C, crystallinities of 5.4–53%, and hexene percentages of 0.3–14.2 can be efficiently produced. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4327–4336, 2004     

Methyl branching in polyethylene from homopolymerization of ethylene with N‐arylcyano‐β‐diketiminate methallyl nickel‐B(C6F5)3

N‐Arylcyano‐β‐diketiminate methallyl nickel complexes activated with B(C₆F₅)₃ were used in the polymerization of ethylene. The microstructure analysis of obtained polyethylene (PE) was done by differential scanning calorimetry and ¹³C nuclear magnetic resonance (NMR). The branched polymer structures produced by these catalysts were attributed to one step isomerization mechanism of the catalyst along the polymer chain. The ortho or para position of the cyano group with co‐ordinated B(C₆F₅)₃ in both methallyl nickel catalysts influenced the polymer molecular weight, branching, and consequently melting and crystallization temperatures. NMR spectroscopic studies showed predominantly the formation of methyl branches in the obtained PE. Catalysts under study gave linear low‐density PEs with good crystallinities at temperatures of reaction between 50 °C and 70 °C at moderate pressures (12.3 atm). A propylene–ethylene copolymer produced by the metallocene catalyst had the same concentration of branches as the PE synthesized from methallyl nickel/B(C₆F₅)₃. Comparing the two polyolefins with the same degree of branching, it was observed that the polymer obtained with the nickel catalyst proved to be twice more crystalline and had greater T_m. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 452–458     

Derivatization of propene/methyloctadiene copolymers: A flexible approach to side‐chain‐functionalized polypropenes

The copolymerization of propene with 7‐methyl‐1,6‐octadiene (MOD) catalyzed by Cp*TiMe₃/B(C₆F₅)₃ ( A ) and rac‐C₂H₄(Ind)₂ZrCl₂/methylaluminoxane ( B ) in toluene under 1 bar propene gave copolymers with unsaturated side chains. Under these conditions, catalyst A produced copolymers with an atactic backbone structure of type 1 , with 3.5–19.6 mol % MOD incorporation and weight‐average molecular weight = 0.7–2.7 × 10⁵. Using catalyst B , copolymers 2 with 0.4–3.8 mol % MOD incorporation were prepared. The comonomer incorporation was a linear function of the feed ratio. The titanium catalyst A had a significantly higher affinity for MOD than the sterically more hindered zirconocene B . Postpolymerization modification of the side‐chain C?C bond allowed the facile introduction of a wide variety of functional groups. Epoxidation and especially ozonolysis of the C?C bond, to give ? CHO and ? COOH functionalized copolymers, proved to be very facile routes to functionalized polypropenes. According to monitoring by NMR, most of these transformations proceed in an essentially quantitative conversion. As an example of potential applications of such polymers, polypropenes with covalently attached dyes were prepared that are suitable for blending. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1484–1497, 2002