Photoluminescence of osmocene and decamethylosmocene

Osmocene (and decamethylosmocene) is characterized by a lowest-energy ligand field triplet which occurs at _max=372nm (374nm) in absorption and 567nm (572nm) in emission. This orange–yellow phosphorescence is rather intense at 77K but is also visible at r.t.     

Multi-Syringe Flow Injection System with In-Line Pre-Concentration for the Determination of Total Phenolic Compounds

A multi-syringe flow injection system for the determination of total phenolics based on the 4-aminoantipyrine reaction is proposed. In-line preconcentration using solid-phase extraction was implemented, offering an environmentally friendly alternative to organic solvent extraction performed in the batch procedure and in previously described flow methodologies. Therefore, phenolic compounds were retained in Amberlite XAD4 resin using acidic conditions. The elution was carried out using 0.10molL^–1 NaOH solution, promoting the ionisation of the retained phenolic compounds, and thus their desorption.Since different elution profiles were obtained for several phenol derivatives, the calibration curves were established using the peak area as analytical signal. Moreover, a dynamic calibration range was applied by using a variable sample volume (0.500–6.00mL) and calibration curves based on the mass of phenol retained in the pre-concentration column. A methodology based on a fixed sample volume (24.0mL) was also proposed for determination at concentration levels below 50µgL^–1. A limit of detection of 52ng of phenol (9 or 2µgL^–1) was achieved with a sampling frequency of 10–16h^–1 for the variable volume method and 4h^–1 for the fixed volume method. The application of the proposed methodology to reference material provided results that were within the certified acceptance limits.     

Au-Induced Faceting of Si(5 5 12)

The growth of Au on the stable, high-index Si(5512) surface has been studied using scanning tunneling microscopy (STM). At very low coverages and moderate annealing temperatures (0.1ML, 400–500°C), Au appears to decorate the underlying Si rows and form an array of rows that maintains the underlying (5512) periodicity of 5.4nm. For higher annealing temperatures and coverages, however, Au causes faceting to a number of nearby planes. The two primary facets formed at lower (0.15ML) and higher (0.5–2ML) coverages are the (337) and (225) planes, which are tilted 0.7° down [towards (111)] and 1.1° up from (5512), respectively. Both orientations are in fact subunits of the (5512) unit cell, so their presence is not surprising. In addition to these facets, two types of sawtooth morphologies composed of planes oriented further from (5512) are found at very high annealing temperatures (800–900°C). These include (113)+(7715) planes at very low coverage (0.05ml) and (113)+(5511) planes at higher coverage (1ML), where (113) is tilted up by 5.3° and (7715) and (5511) are tilted down by 2.9° and 2.2°, respectively. Au adsorption on Si(5512) therefore results in the formation of five possible facet planes: (113), (225), (337), (5511), and (7715).     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Non-Aqueous Capillary Electrophoresis with Indirect Photometric Detection for Direct Analysis of Pb2+, Zn2+ and Cd2+ Ions

A new approach, based on non-aqueous capillary electrophoresis separation and indirect photometric detection, was established for the determination of the transition metal ions Pb²⁺, Zn²⁺ and Cd²⁺. Under optimized conditions, the method produced baseline separation of these three metal ions. The linear range and detection limits were 1050µM, 1.9µM for Cd²⁺; 1050µM, 2.1µM for Zn²⁺; and 20100µM, 3.8µM for Pb²⁺, respectively.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

Fluorescence Quenching Studies of Curcumin by Hydrogen Peroxide in Acetonitrile Solution

Summary. Steady state quenching studies of curcumin, 1,7-bis(4-hydroxy-3-methoxyphenyl)-1,6-heptadiene-3,5-dione, fluorescence by hydrogen peroxide were conducted in acetonitrile solution. A quenching rate constant, k_q, of 1.05×10¹⁰M^–1·s^–1 was obtained with a short fluorescence lifetime of 347ps. The reaction rate constant, which is within the diffusion-limited regime, is activation-controlled. The rate constant of deactivation of the thermally excited curcumin was 1.2 orders of magnitude more nonradiative (2.67×10⁹s^–1) than radiative (2.16×10⁸s^–1). The reaction was exothermic with a G° of –1.97eV and solvent reorganization energy of 1.37eV. These values indicate that the electron transfer reaction is solvent-mediated with electron transfer rate constant, k_ET, of 2.16×10¹⁰s^–1.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Column Solid-Phase Extraction with 2-Acetylmercaptophenyldiazoaminoazobenzene (AMPDAA) Impregnated Amberlite XAD-4 and Determination of Trace Heavy Metals in Natural Waters by Flame Atomic Absorption Spectrometry

A column solid-phase extraction (SPE) preconcentration method was developed for the determination of Cd, Co, Cu, Ni and Zn ions in natural water samples by flame atomic absorption spectrometry. The procedure is based on the retention of analytes in the form of 2-acetylmercaptophenyldiazoaminoazobenzene (AMPDAA) complexes on a short column of AMPDAA-XAD-4 resin from buffered sample solution and subsequent elution with hydrochloric acid plus sodium chloride. Important SPE parameters were optimized using model solutions. The loading half-time, t_1/2, for Cd, Co, Cu and Zn was found to be less than 5min, and for Ni the value was 12min. The detection limit for Cd, Co, Cu, Ni and Zn was 0.028, 0.064, 0.042, 0.023 and 0.16µgL^–1, respectively, and the quantification limit was 0.043, 0.11, 0.099, 0.044 and 0.29µgL^–1, respectively. The AMPDAA-XAD-4 resin has good selectivity for Cd, Co, Cu, Ni and Zn over several electrolytes, especially over earth alkaline metals with tolerance limits of 0.05molL^–1. The method was validated by analysing a standard reference material (GBW 08301), and it was found that the results agree with those quoted by the manufactures. The developed method was applied to the determination of trace metal ions in tap water and river water samples with satisfactory results.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Determination of Proteins at Nanogram Levels Using the Resonance Light Scattering Technique with a Novel PVAK Nanoparticle

A novel functionalized polyvinyl alcohol keto-derivative nanoparticle (PVAK) has been prepared in a one-step method using oxidation and degradation under ultrasonic irradiation. The nanoparticle is water-soluble, chemically stable, non-toxic and biocompatible. The surface of the nanoparticle is covered with abundant hydroxyl, carbonyl and carboxyl. At pH 3.0, the interactions of PVAK with different proteins can result in obviously enhanced RLS signals at 380nm. Under optimal conditions, the calibration graphs are linear over the range of 0.024.0µgmL^–1 for human serum albumin (HSA), 0.023.5µgmL^–1 for bovine serum albumin (BSA), and 0.053.5µgmL^–1 for human -globulin (-G), respectively. Detection limits were 6.4ngmL^–1 for HSA, 9.2ngmL^–1 for BSA, and 12.5ngmL^–1 for -G, respectively. The method was employed for the determination of total proteins in human serum with satisfactory results.     

Use of 2,4-dinitrophenylhydrazone of glyoxylic acid for the determination of glyoxylic acid by the chromatographic-spectrophotometric method and by differential pulse polarography

Two different methods (one based on chromatography and spectrophotometry and the other on polarography) have been developed for the determination of glyoxylic acid in the form of a derivative with 2,4-dinitrophenylhydrazine (DNPHGA). The TLC method allows the separation of two DNPHGA isomers (trans and cis). Spectrophotometric measurements of the eluents of the separated compounds (=360 nm) allow the determination of GA within the range from 4 to 30 g. Using differential pulse polarography, the conditions of DNPHGA formation were examined. The reduction peak of this derivative (E_P=–0.430 V), observed by dpp, was used to develop a polarographic determination of GA within the concentration range from 110^-4 to 710^–4 mol/l.     

Preparation of a Novel Agarose-Salen Adsorbent,and its Use for Efficient Column Preconcentration and Flame AAS Determination of Lead in Water

A cross-linked agarose (Novarose) support was chemically modified with a novel salen-type Schiffs base; 2,2-[1,2-ethandiyl bis(nitrilimethylidyne)] bis(orthocresol) and was used to develop an efficient, simple and low-cost method for matrix separation and preconcentration of lead in water. The binding capacity of the adsorbent, packed in a 6.5mm i.d. glass column, was tested for different metal ions, and a capacity of 4973 (±95) µg per mL of packed adsorbent for triplicate measurements was obtained for lead at pH 6.0.The effects of pH, ionic strength, buffer concentration, sample volume, eluent concentration and volume, and matrix ions on the column recovery of Pb²⁺ were carefully studied. Quantitative recoveries were obtained for the analyte in a pH range of 5.5 to 7.0. Enrichment volumes up to 300mL and ionic strengths up to 0.5molL^–1 had no significant effect on the recovery of Pb²⁺. The method also tolerated relatively high concentrations of matrix ions such as Ca²⁺, Mg²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Mg²⁺ and Cd²⁺ with no considerable effect on the analytes signal. A few mL of 0.4molL^–1 hydrochloric acid was sufficient for quantitative elution of the analyte from a 0.5mL column before its flame AAS determination. Preconcentration factors up to 60 and a detection limit of 2.5µgL^–1 were obtained for the method. The precision, expressed as relative standard deviation, was 2.9% (at 100µgL^–1) calculated from six replicate measurements. The method was successfully applied to the determination of Pb²⁺ in some river and spiked river water samples with good precision.     

Kinetics of EDTA-catalyzed oxidation of Indigo Carmine by vanadium(V)

The reaction is first order both in vanadium(V) and substrate and is markedly inhibited by H⁺ ions. Kinetic evidence for the formation of a 11 complex of vanadium(V) and EDTA is obtained. The stability constant of this complex and its thermodynamic parameters were evaluated. A suitable mechanism is proposed.

---

(V), H⁺. 11 (V) . . .

     

Investigation of Medium Power Radiofrequency Capacitively Coupled Plasmas and Their Application to Atomic Emission Spectrometry for the Determination of Aluminium in Water Samples

A medium power radiofrequency capacitively coupled plasma (275W, 27.12MHz) with low argon consumption (0.5Lmin^–1) was investigated to be used for the determination of aluminium in water samples pneumatically nebulised by atomic emission spectrometry. The plasma torch was operated in two geometric configurations, coaxial and coaxial-annular with single (SRTr.f.CCP) or double ring electrodes (DRTr.f.CCP), respectively. The optimum experimental parameters (observation height, Ar flow rate, distance between ring electrodes, matrix interference of Na⁺ and Ca²⁺ and anion nature) for Al 396.152nm emission were established. Under optimum operating conditions of the DRTr.f.CCP torch (6cm distance between annular electrodes), a detection limit of 70ngmL^–1 aluminium was found. Both operating parameters and several figures of merit of the investigated plasmas were compared to those of microwave plasmas and inductively coupled plasma used in atomic emission spectrometry. The method was used to control the quality of drinking and industrial water. Samples were mineralised with 2mL of 1+1 HNO₃ and 10mL of 1+1 HCl. In the range of 0.15–3.5mgL^–1 Al³⁺ the relative standard deviation varied between 3.7 and 8.6% (n=3). For two certified drinking water samples containing 0.206 and 0.218mgL^–1 Al³⁺ the recovery (n=5) was 97.6±6.8% and 98.6±7.3%, respectively.     

Indirect Determination of Sulfide by Cold Vapor Atomic Absorption Spectrometry

A method for the determination of sulfide based on its interference with the determination of Hg by cold vapor atomic absorption spectrometry is described. The decrease in mercury absorbance at 253.7nm is proportional to the concentration of sulfide over the range of 10–320ngmL^–1. The limit of detection was found to be 7ngmL^–1 and the relative standard deviation (R.S.D.) for the determination of different concentrations of sulfide was in the range of 1.8–2.2%. This method was applied to the determination of sulfide in whole human blood after gas-phase separation.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Methane Adsorption and Plasma-Assisted Catalytic Conversion on the Surface of γ-Alumina

Diffuse scattering IR spectroscopy was applied to study the adsorption and plasma-assisted catalytic conversion of methane (deuteromethane) on the surface of -alumina. It was found that CH₄ adsorption sites on the -Al₂O₃ surface were formed by molecular and dissociative mechanisms under the action of an electric-discharge plasma at room temperature. As distinct from -radiolysis, plasma treatment leads to the formation of acetylene in addition to other hydrocarbon products, aluminum hydrides, and surface hydroxyl groups. Plausible mechanisms were proposed for plasma-assisted catalytic reactions in the -Al₂O₃–adsorbed CH₄(CD₄) system.     

Specific activity of ruthenium for hydrogenation and hydrogenolysis of benzene in relation to metal dispersity

The specific activity V_sp of ruthenium supported on -alumina (0.084–0.84 wt.%, average particle size 1=1–7 nm) has been investigated for hydrogenation and hydrogenolysis of benzene at 80–320°C and compared with that of Ru powder of 1>1400 nm. A decrease of V_sp with increasing Ru dispersity was found for both reactions, the decrease having been more pronounced for hydrogenolysis. The effect is considered to be due mainly to an influence of dispersity of supported metal on the mode and extent of benze chemisorption.

---

(V_Sp) , - (0,084–0,84 .%, 1=1–7 ), 80–320°C - 1>1400 . V_Sp , . , -, - .

     

Influence of cerium and lanthanum cations on the thermal stability of HY zeolite. Characterization of the zeolitic structure by nitrogen adsorption

Capacities for nitrogen adsorption of HY, CeHY and LaHY zeolites have been measured after calcination at several temperatures. CeHY and LaHY zeolites were prepared by ion exchange of HY, both presenting the same rare earth exchange ratio of 41%. Rare earth HY zeolites calcined at 1073 K present higher adsorption capacity than HY, which allows to conclude that cerium and mainly lanthanum increase the thermal stability of HY zeolite.

---

HY, CeHY LaHY . CeHY LaHY HY, , 41%. 1073 K HY. , , , HY.