Importance of MS selectivity and chromatographic separation in LC-MS/MS-based methods when investigating pharmaceutical metabolites in water. Dipyrone as a case of study

Pharmaceuticals are emerging contaminants of increasing concern because of their presence in the aquatic environment and potential to reach drinking-water sources. After human and/or veterinary consumption, pharmaceuticals can be excreted in unchanged form, as the parent compound, and/or as free or conjugated metabolites. Determination of most pharmaceuticals and metabolites in the environment is commonly made by liquid chromatography (LC) coupled to mass spectrometry (MS). LC coupled to tandem MS is the technique of choice nowadays in this field. The acquisition of two selected reaction monitoring (SRM) transitions together with the retention time is the most widely accepted criterion for a safe quantification and confirmation assay. However, scarce attention is normally paid to the selectivity of the selected transitions as well as to the chromatographic separation. In this work, the importance of full spectrum acquisition high-resolution MS data using a hybrid quadrupole time-of-flight analyser and/or a suitable chromatographic separation (to reduce the possibility of co-eluting interferences) is highlighted when investigating pharmaceutical metabolites that share common fragment ions. For this purpose, the analytical challenge associated to the determination of metabolites of the widely used analgesic dipyrone (also known as metamizol) in urban wastewater is discussed. Examples are given on the possibilities of reporting false positives of dypirone metabolites by LC-MS/MS under SRM mode due to a wrong assignment of identity of the compounds detected. Copyright ? 2012 John Wiley & Sons, Ltd.     

Shotgun lipidomics on a LTQ Orbitrap mass spectrometer by successive switching between acquisition polarity modes

Top-down shotgun lipidomics relies on direct infusion of total lipid extracts into a high-resolution tandem mass spectrometer and implies that individual lipids are recognized by their accurately determined m/z. Lipid ionization efficiency and detection specificity strongly depend on the acquisition polarity, and therefore it is beneficial to analyze lipid mixtures in both positive and negative modes. Hybrid LTQ Orbitrap mass spectrometers are widely applied in top-down lipidomics; however, rapid polarity switching was previously unfeasible because of the severe and immediate degradation of mass accuracy. Here, we report on a method to rapidly acquire high-resolution spectra in both polarity modes with sub-ppm mass accuracy and demonstrate that it not only simplifies and accelerates shotgun lipidomics analyses but also improves the lipidome coverage because more lipid classes and more individual species within each class are recognized. In this way, shotgun analysis of total lipid extracts of human blood plasma enabled to quantify 222 species from 15 major lipid classes within 7?min acquisition cycle.     

Identification of isomeric 5-hydroxytryptophan- and oxindolylalanine-containing peptides by mass spectrometry

Cells continuously produce reactive oxidative species that can modify all cellular components. In proteins, for example, cysteine, methionine, tryptophan (Trp), and tyrosine residues are particularly prone to oxidation. Here, we report two new approaches to distinguish two isomeric oxidation products of Trp residues, i.e. 5-hydroxytryptophan (5-HTP) and oxindolylalanine (Oia) residues, in peptides. First, 2-nitrobenzenesulfenyl chloride, known to derivatize Trp residues in position 2 of the indole ring, was used to label 5-HTP residues. The mass shift of 152.98 m/z units allowed identifying 5-HTP- besides Trp-containing peptides by mass spectrometry, whereas Oia residues were not labeled. Second, fragmentation of the Oia- and 5-HTP-derived immonium ions at m/z 175.08 produced ions characteristic for each residue that allowed their identification even in the presence of y(1) ions at m/z 175.12 derived from peptides with C-terminal arginine residues. The pseudo MS(3) spectra acquired on a quadrupole time-of-flight hybrid mass spectrometer displayed two signals at m/z 130.05 and m/z 132.05 characteristic for Oia-containing peptides and a group of six signals (m/z 103.04, 120.04, 130.04, 133.03, 146.04, and 148.04) for 5-HTP-cointaining peptides. In both cases, the relative signal intensities appeared to be independent of the sequence providing a specific fingerprint of each oxidative modification.     

Structural characterisation of N-linked glycan mixtures by precursor ion scanning and tandem mass spectrometric analysis

2-Aminoacridone (2-AMAC) labelled N-linked glycan pools were analysed directly by a hybrid quadrupole orthogonal acceleration time-of-flight mass spectrometer (Q-Tof) in the precursor ion scanning and tandem mass spectrometry (MS/MS) modes. The use of a precursor ion scanning strategy on this instrument provides a rapid and sensitive method of screening glycan mixtures, without prior separation by chromatographic methods. It allows facile and preliminary characterisation of glycans into different classes, for example, high-mannose or complex glycans. Preliminary sequencing information for each glycan is obtained in the initial precursor ion scanning mode, but further sequencing information of selected glycans can be obtained using the MS/MS mode. Copyright 1999 John Wiley & Sons, Ltd.     

The Ion-optical scheme of a portable mass spectrometer

An ion-optical scheme for a portable magnetic double-focusing mass spectrometer that makes it possible to analyze several components simultaneously over a wide mass range (the mass-spectrograph operating mode) is proposed. This scheme effectively solves the research and technological problems involving the analysis of rapidly varying compositions.     

Plasma Source Mass Spectrometric Analysis of Biological and Environmental Samples: Dealing with Potential Interferences

Introduction

Effectiveness of a plasma to dissociate the sample into ions has been the basis of the development of plasma source optical emission spectrometer (OES) and mass spectrometer (MS) for elemental and isotope analysis. Among the available ways of inducing and sustaining a plasma, only inductively coupled plasma (ICP) has gained commercial application. The ICP is an electrodeless discharge in a gas at atmospheric pressure, maintained by energy coupled to it from a radio frequency generator. This is done by a coupling coil, which functions as the primary of radio frequency transformer, the secondary of which is created by the discharge itself (Jarvis et al., 1992). An ICP-MS system consists of a plasma source (ICP) interfaced with a quadrupole MS. The plasma ionizes the elements of the sample and the MS serves as a detector that measures the mass to charge (m/z) ratio of the element(s) or isotope(s) of interest. Generally an argon (Ar) plasma is used, but other plasma sources have also been proposed (Brown et al., 1988; Satzger et al., 1987).     

Ionic desorption in valence- and core-excited poly(vinyl chloride)

Photon stimulated ion desorption (PSID) studies have been performed in poly(vinyl chloride) (PVC) using synchrotron radiation, encompassing the valence and core electron (Cl 2p and C 1s) energy ranges. Data acquisition was performed at the Brazilian synchrotron light source (LNLS), operating in a multi-bunch mode and using a time-of-flight mass spectrometer (TOF-MS). A pulsed high voltage applied to the sample was used as a trigger for the TOF-MS experiments. Ionic desorption from PVC shows strong selectivity in the formation of chlorine ions around the Cl 2p-edge while very similar fragmentation patterns are observed for the other energies studied.     

Full utilization of a mass spectrometer using on-demand sharing with multiple LC units

The applicability of liquid chromatography-mass spectrometry (LC/MS) is often limited by throughput. The sharing of a mass spectrometer with multiple LCs significantly improves throughput; however, the reported systems have not been designed to fully utilize the MS duty cycle, and as a result to achieve maximum throughput. To fully utilize the mass spectrometer, the number of LC units that a MS will need to recruit is application dependent and could be significantly larger than the current commercial or published implementations. For the example of a single analyte, the number may approach the peak capacity to a first degree approximation. Here, the construction of a MS system that flexibly recruits any number of LC units demanded by the application is discussed, followed by the method to port a previously developed LC/MS method to the system to fully utilize a mass spectrometer. To demonstrate the performance and operation, a prototypical MS system of eight LC units was constructed. When 1-min chromatographic separations were performed in parallel on the eight LCs of the system, the average LC/MS analysis time per sample was 10.5 s when applied to the analysis of samples in 384-well plate format. This system has been successfully used to conduct large-volume biochemical assays with the analysis of a variety of molecular entities in support of drug discovery efforts. Allowing the recruitment of the number of LC units appropriate for a given application, this system has the potential to be a plug-and-play system to fully utilize a mass spectrometer. Copyright ? 2012 John Wiley & Sons, Ltd.     

Isotope ratio monitoring gas chromatography/Mass spectrometry of D/H by high temperature conversion isotope ratio mass spectrometry

Of all the elements, hydrogen has the largest naturally occurring variations in the ratio of its stable isotopes (D/H). It is for this reason that there has been a strong desire to add hydrogen to the list of elements amenable to isotope ratio monitoring gas chromatography/mass spectrometry (irm-GC/MS). In irm-GC/MS the sample is entrained in helium as the carrier gas, which is also ionized and separated in the isotope ratio mass spectrometer (IRMS). Because of the low abundance of deuterium in nature, precise and accurate on-line monitoring of D/H ratios with an IRMS requires that low energy helium ions be kept out of the m/z 3 collector, which requires the use of an energy filter. A clean mass 3 (HD(+.)) signal which is independent of a large helium load in the electron impact ion source is essential in order to reach the sensitivity required for D/H analysis of capillary GC peaks. A new IRMS system, the DELTA(plus)XL(trade mark), has been designed for high precision, high accuracy measurements of transient signals of hydrogen gas. It incorporates a retardation lens integrated into the m/z 3 Faraday cup collector. Following GC separation, the hydrogen bound in organic compounds must be quantitatively converted into H(2) gas prior to analysis in the IRMS. Quantitative conversion is achieved by high temperature conversion (TC) at temperatures >1400 degrees C. Measurements of D/H ratios of individual organic compounds in complicated natural mixtures can now be made to a precision of 2 per thousand (delta notation) or, better, with typical sample amounts of approximately 200 ng per compound. Initial applications have focused on compounds of interest to petroleum research (biomarkers and natural gas components), food and flavor control (vanillin and ethanol), and metabolic studies (fatty acids and steroids). Copyright 1999 John Wiley & Sons, Ltd.     

Identification and structural characterization of in vivo metabolites of ketorolac using liquid chromatography electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS)

In vivo metabolites of ketorolac (KTC) have been identified and characterized by using liquid chromatography positive ion electrospray ionization high resolution tandem mass spectrometry (LC/ESI-HR-MS/MS) in combination with online hydrogen/deuterium exchange (HDX) experiments. To identify in vivo metabolites, blood urine and feces samples were collected after oral administration of KTC to Sprague-Dawley rats. The samples were prepared using an optimized sample preparation approach involving protein precipitation and freeze liquid separation followed by solid-phase extraction and then subjected to LC/HR-MS/MS analysis. A total of 12 metabolites have been identified in urine samples including hydroxy and glucuronide metabolites, which are also observed in plasma samples. In feces, only O-sulfate metabolite and unchanged KTC are observed. The structures of metabolites were elucidated using LC-MS/MS and MS(n) experiments combined with accurate mass measurements. Online HDX experiments have been used to support the structural characterization of drug metabolites. The main phase I metabolites of KTC are hydroxylated and decarbonylated metabolites, which undergo subsequent phase II glucuronidation pathways.     

Investigation of the quantitative properties of the quadrupole orthogonal acceleration time-of-flight mass spectrometer with electrospray ionisation using 3,4-methylenedioxymethamphetamine

This paper describes the investigation of the potential of a quadrupole orthogonal acceleration time-of-flight mass spectrometer (Q-TOF) equipped with an atmospheric pressure ionisation interface for quantitative measurements of small molecules separated by reversed phase liquid chromatography. To this end, the detection limits and linear dynamic range in particular were studied in an LC/MS/MS experiment using 3,4-methylenedioxymethamphetamine standards and 3,4-methylenedioxyethylamphetamine for internal standardisation. In a second phase, the experiment was repeated with real biological extracts (whole blood, serum, and vitreous humour). A calibration for 3,4-methylenedioxymethamphetamine and its metabolite 3,4-methylenedioxyamphetamine was prepared in each of these matrices again using 3,4-methylenedioxyethylamphetamine as internal standard. The resulting quantitative data were compared with those obtained by liquid chromatography with fluorescence detection for the same extracts. The Q-TOF results revealed excellent sensitivity and a linear dynamic range of nearly four decades (2-10 000 pg on-column, r(2) = 0.9998, 1/x weighting). Furthermore, all the calibration curves prepared in biological material were superimposable, LC/MS/MS and LC-fluorescence, and the quantitative results for actual samples compared very favourably. It was concluded that the Q-TOF achieves a linear dynamic range for quantitative LC/MS/MS work exceeding that of fluorescence detection and at much better absolute sensitivity. Copyright 1999 John Wiley & Sons, Ltd.     

多维核磁共振数据在通用计算机上的处理与三维谱的观测

本文分析、讨论了利用外部通用计算机处理核磁共振数据的方法及程序,包括数据格式转换,一维、二维、三维谱的数据处理,谱图的显示及输出,并以VAX机为例实现了三维谱的观测。文中还详细讨论了编程的原理和一些技术细节。     

Simultaneous analysis of several synthetic cannabinoids, THC, CBD and CBN, in hair by ultra-high performance liquid chromatography tandem mass spectrometry. Method validation and application to real samples

A simple procedure for the quantitative detection of JWH-018, JWH-073, JWH 200, JWH-250, HU-210, Δ(9)-tetrahydrocannabinol (THC), cannabidiol (CBD) and cannabinol (CBN) in hair has been developed and fully validated. After digestion with NaOH and liquid-liquid extraction, the separation was performed with an ultra-high performance liquid chromatography system coupled to a triple quadrupole mass spectrometer operating in the selected reaction monitoring mode. The absence of matrix interferents, together with excellent repeatability of both retention times and relative abundances of diagnostic transitions, allowed the correct identification of all analytes tested. The method was linear in two different intervals at low and high concentration, with correlation coefficient values between 0.9933 and 0.9991. Quantitation limits ranged from 0.07 pg/mg for JWH-200 up to 18 pg/mg for CBD The present method for the determination of several cannabinoids in hair proved to be simple, fast, specific and sensitive. The method was successfully applied to the analysis of 179 real samples collected from proven consumers of Cannabis, among which 14 were found positive to at least one synthetic cannabinoid.     

Mass Spectrometry,Review of the Basics: Electrospray,MALDI, and Commonly Used Mass Analyzers

Abstract

Mass spectrometry (MS) has progressed to become a powerful analytical tool for both quantitative and qualitative applications. The first mass spectrometer was constructed in 1912 and since then it has developed from only analyzing small inorganic molecules to biological macromolecules, practically with no mass limitations. Proteomics research, in particular, increasingly depends on MS technologies. The ability of mass spectrometry analyzing proteins and other biological extracts is due to the advances gained through the development of soft ionization techniques such as electrospray ionization (ESI) and matrix-assisted laser desorption ionization (MALDI) that can transform biomolecules into ions. ESI can efficiently be interfaced with separation techniques enhancing its role in the life and health sciences. MALDI, however, has the advantage of producing singly charges ions of peptides and proteins, minimizing spectral complexity. Regardless of the ionization source, the sensitivity of a mass spectrometer is related to the mass analyzer where ion separation occurs. Both quadrupole and time of flight (ToF) mass analyzers are commonly used and they can be configured together as QToF tandem mass spectrometric instruments. Tandem mass spectrometry (MS/MS), as the name indicates, is the result of performing two or more sequential separations of ions usually coupling two or more mass analyzers. Coupling a quadrupole and time of flight resulted in the production of high-resolution mass spectrometers (i.e., Q-ToF). This article will historically introduce mass spectrometry and summarizes the advantages and disadvantages of ESI and MALDI along with quadrupole and ToF mass analyzers, including the technical marriage between the two analyzers. This article is educational in nature and intended for graduate students and senior biochemistry students as well as chemists and biochemists who are not familiar with mass spectrometry and would like to learn the basics; it is not intended for mass spectrometry experts.     

Barium/barium oxide dispensation rate measurement

A quantitative knowledge of the Ba/BaO dispensation rate is necessary in order to understand the physics and chemistry of dispenser cathode surfaces, and the consequent cathode activity. This paper discusses three devices for determining Ba/BaO evaporation rate: the quartz crystal microbalance, the quadrupole mass spectrometer, and the Becker diode. An improved Becker diode technique is described which eliminates the drawbacks of the classical methods, and therefore may be suitable for routine use.     

Ultrahigh resolution mass spectrometry and accurate mass measurements for high-throughput food lipids profiling

In the present study, accurate mass measurements by ultrahigh resolution mass spectrometry with Orbitrap-Exactive working at resolving power R: 100,000 (m/z 200, full width at half maximum) with an accuracy better than 2?ppm in all the mass range (m/z 200 to 2000) were used to show a detailed molecular composition of diverse edible oils and fats. Flow injection was used to introduce samples into the mass spectrometer, obtaining a complete analysis of each sample in less than 10 min, including blanks. Meticulous choice of organic solvents and optimization of the ion source and Orbitrap mass analyzer parameters were carried out, in order to achieve reproducible mass spectra giving reliable elemental compositions of the lipid samples and to prevent carry over. More than 200 elemental compositions attributable to diacylglycerols, triacylglycerols (TAGs), and their oxidation products have been found in the spectra of food lipids from different origin. Several compounds with very close molecular mass could only be resolved through ultrahigh resolution, allowing detailed and robust TAG profiling with a high characterization potential. Copyright ? 2012 John Wiley & Sons, Ltd.     

Sensitive analysis of metal cations in positive ion mode electrospray ionization mass spectrometry using commercial chelating agents and cationic ion-pairing reagents

Metals play a very important role in many scientific and environmental fields, and thus their detection and analysis is of great necessity. A simple and very sensitive method has been developed herein for the detection of metals in positive ion mode ESI-MS. Metal ions are positively charged, and as such they can potentially be detected in positive ion mode ESI-MS; however, their small mass-to-charge (m/z) ratio makes them fall in the low-mass region of the mass spectrum, which has the largest background noise. Therefore, their detection can become extremely difficult. A better and well-known way to detect metals by ESI-MS is by chelating them with complexation agents. In this study eleven different metals, Fe(II), Fe(III), Mg(II), Cu(II), Ru(III), Co(II), Ca(II), Ni(II), Mn(II), Sn(II), and Ag(I), were paired with two commercially available chelating agents: ethylenediaminetetraacetic acid (EDTA) and ethylenediaminedisuccinic acid (EDDS). Since negative ion mode ESI-MS has many disadvantages compared to positive ion mode ESI-MS, it would be very beneficial if these negatively charged complex ions could be detected in the positive mode. Such a method is described in this paper and it is shown to achieve much lower sensitivities. Each of the negatively charged metal complexes is paired with six cationic ion-pairing reagents. The new positively charged ternary complexes are then analyzed by ESI-MS in the positive single ion monitoring (SIM) and single reaction monitoring (SRM) modes. The results clearly revealed that the presence of the cationic reagents significantly improved the sensitivity for these analytes, often by several orders of magnitude. This novel method developed herein for the detection of metals improved the limits of detection (LODs) significantly when compared to negative ion mode ESI-MS and shows great potential in future trace studies of these and many other species.     

Time-of-flight mass spectrometer coupled to a position sensitive detection

In this article we present the first results that we have obtained with a time-of-flight mass spectrometer coupled to a position sensitive detector. This new spectrometer provides a three-dimensional imaging (X and Y positions and time-of-flight) of the ion packet on the detector, with a high acquisition rate and a high resolution on both the mass and the position. This new apparatus is used to measure the electric deflection of PABA (p-amino benzoic acid) and PABA dimer beams and to study the kinetic energy release of the photofragmentation of the PABA dimer.     

IBM PC controller for Bruker EN250 ENDOR system

Module upgrading the existing IBM PC data acquisition and processing system for Bruker ER200D equipped with EN250 ENDOR attachment is described. The old ASPECT 2000 computer is fully replaced by a modern IBM PC without any modification of the Bruker EN003 ENDOR standard interface. Thus the spectrometer can operate under IBM PC control in ENDOR and TRIPLE modes. Moreover its features are extended with ENDOR INDUCED EPR operating mode which was not available before.     

Ion/molecule reactions provide new evidence for the structure and origin of

Ion/molecule reactions leading to formation of the diagnostically useful [C(3)H(4)N](+) ion (m/z 54), from acetonitrile CI plasma, have been studied using a tandem quadrupole mass spectrometer. Evidence is presented to demonstrate that [C(3)H(4)N](+) is produced from an ion/molecule reaction between [C(2)H(2)N](+) (m/z 40) and neutral acetonitrile, via a [C(4)H(5)N(2)](+) (m/z 81) intermediate. Loss of HCN, where the H atom arises from neutral acetonitrile and the CN group from [C(2)H(2)N](+) (m/z 40), leads to the production of [C(3)H(4)N](+) (m/z 54). These results are consistent with a proposed concerted elimination of HCN, generating m/z 54 as a methylene vinylidene ammonium ion. Copyright 1999 John Wiley & Sons, Ltd.