Investigations of thickness-shear mode elastic constant and damping of shunted piezoelectric materials with a coupling resonator

Shear-mode piezoelectric materials have been widely used to shunt the damping of vibrations where utilizing surface or interface shear stresses. The thick-shear mode(TSM) elastic constant and the mechanical loss factor can change correspondingly when piezoelectric materials are shunted to different electrical circuits. This phenomenon makes it possible to control the performance of a shear-mode piezoelectric damping system through designing the shunt circuit. However, due to the difficulties in directly measuring the TSM elastic constant and the mechanical loss factor of piezoelectric materials, the relationships between those parameters and the shunt circuits have rarely been investigated. In this paper, a coupling TSM electro–mechanical resonant system is proposed to indirectly measure the variations of the TSM elastic constant and the mechanical loss factor of piezoelectric materials. The main idea is to transform the variations of the TSM elastic constant and the mechanical loss factor into the changes of the easily observed resonant frequency and electrical quality factor of the coupling electro–mechanical resonator. Based on this model, the formular relationships are set up theoretically with Mason equivalent circuit method and they are validated with finite element(FE) analyses. Finally, a prototype of the coupling electro–mechanical resonator is fabricated with two shear-mode PZT5 A plates to investigate the TSM elastic constants and the mechanical loss factors of different circuit-shunted cases of the piezoelectric plate. Both the resonant frequency shifts and the bandwidth changes observed in experiments are in good consistence with the theoretical and FE analyses under the same shunt conditions. The proposed coupling resonator and the obtained relationships are validated with but not limited to PZT5 A.     

Sound absorption characteristics of a thin plate with PZT and shunt circuitⅠ.Theoretical analysis

The feasibility of sound absorbing by a vibrating plate with piezoelectric material and shunt circuits is theoretically investigated.Based on an equivalent compliance of a piezoelectric wafer shunted with RL circuits,the governing equations for the flexural vibration of the plate with the piezoelectric wafer are derived using Lagrange's approach.The equations take into account not only the mass,stiffness and structural damping of the plate and the wafer,but also the electrical resistance and electrical i...     

0-3型压电复合材料覆盖层水下 吸声性能的理论研究

目前压电分流阻尼技术在振动和噪声领域的应用得到了广泛的关注. 本文尝试将压电分流阻尼技术应用于水下吸声领域, 以提高覆盖层的吸声性能. 将压电覆盖层厚度模态的机电方程和声波传播的传递矩阵相结合, 建立一维电声模型. 该模型可以用于分析多层压电和非压电水下吸声覆盖层的吸声性能. 采用该模型分析了0-3型压电复合材料覆盖层的水下吸声性能. 压电复合材料的参数是采用Furukawa的模型计算的. 研究结果表明, 采用合适的分流电阻, 负电容分流电路可以在较宽的频率范围显著提高覆盖层的吸声性能. 其原理可以从阻抗匹配的角度解释, 负电容分流电路可以调整压电覆盖层的表面声阻抗, 使之与水的特性声阻抗相匹配.     

混合压电分流电路作用下声子晶体杆振动带隙结构分析

对于电阻电感(RL)及负阻抗变换器(NIC)混合压电分流电路分别采用紧密及间隔排列方式进行带隙结构计算,并且针对分流电路中电阻、电感及电容对于局域共振带隙的影响进行研究。采用传递矩阵法建立了压电分流电路作用下声子晶体杆带隙分析的理论模型,并运用MATLAB语言对带隙结构进行编程仿真计算。通过电阻、电感、电容参数的匹配及电路不同排列方式的对比,最终得到了在混合间隔压电分流电路作用下宽度为13 kHz的带隙,并对振动控制系统稳定性进行了分析。研究结果表明:采用混合压电分流电路会对杆件带隙结果产生影响,且采用压电片间隔排列的方式会使带隙宽度明显扩大。      

LCR分流电路下压电声子晶体智能材料的带隙

将带有LCR分流电路的压电陶瓷片对贴在铝和环氧树脂组成的声子晶体结构中.使智能材料的机械振动与压电陶瓷的压电效应耦合起来,推导出机械振动在压电陶瓷片上的等效附加应力;使LCR分流电路中的电磁振荡效应和声子晶体的能带特性有机结合,计算了在分流电路作用下智能材料扭转和弯曲振动的带隙特性,研究了电阻、电感、电容元件的改变对压电声子晶体智能材料带隙的影响.研究结果表明:在合理尺寸下,随着分流电路中电阻值的增大,带隙的频率范围变宽,但衰减幅值有所降低;电感和电容值的增大都可以使带隙向低频移动,带隙的衰减幅值随着电感值的增大而升高,但随着电容值的增大而降低.从而给压电声子晶体智能材料减震降噪的控制提供了一种新思路.     

Band gap structure analysis of phononic crystal rods with hybrid shunted piezoelectric patches

The band gap structures by arranging hybrid shunted piezoelectric materialswith resistance inductive(RL) circuit and negative impedance converter(NIC) closely and at intervals are presented.The theoretical model is built using transfer matrix method.Then the MATLAB computing language is utilized to simulate the band gap structures.Meanwhile,the effects of the resistance,inductance and capacitance on the local resonant gap are studied.By comparing different combinations of resistance,inductance and capacitance as well as different arrangement of circuits,a 13 kHz band gap is reached under the effect of arranging hybrid periodic shunted piezoelectric patches at intervals and the stability of the system is also analyzed.It is proved that utilizing hybrid shunted piezoelectric patches would have a clear impact on the band gap structure of phononic crystal rods.Moreover,the band gap would be clearly enlarged by arranging hybrid piezoelectric patches at intervals.     

Band gap control of phononic beam with negative capacitance piezoelectric shunt

Periodic arrays of negative capacitance shunted piezoelectric patches are employed to control the band gaps of phononic beams. The location and the extent of induced band gap depend on the mismatch in impedance generated by each patch. The total impedance mismatch is determined by the added mass and stiffness of each patch as well as the shunting electrical impedance. Therefore, the band gap of the shunted phononic beam can be actively tuned by appropriately selecting the value of negative capacitance. The control of the band gap of phononic beam with negative capacitive shunt is demonstrated numerically by employing transfer matrix method. The result reveals that using negative capacitive shunt to tune the band gap is effective.     

应用长度极化压电陶瓷33模态的 半主动减振技术研究*

本文提出利用长度方向极化的压电材料的33模态来实现半主动减振。论文以横梁为例,通过理论分析和有限元仿真,对比研究了当压电材料分别连接31, 33两种模态对应的最佳分流电路时,压电材料两种模态在横梁的共振频率附近的减振效果。结果表明33模态比31模态具有更高的减振效率。此外,鉴于33模态存在极化长度有限的问题,仿真分析了压电材料的尺寸和位置对减振效果的影响。在此基础之上,提出了一个利用压电材料33模态的多模态减振的组合设计,对横梁的前三个模态起到了很好地减振作用。相对31模态而言,横梁的每个振动模态均有约15dB的减振提升。     

Modeling and analysis of laminate composite plates with embedded active-passive piezoelectric networks

The objective of this work is to present the finite element modeling of laminate composite plates with embedded piezoelectric patches or layers that are then connected to active-passive resonant shunt circuits, composed of resistance, inductance and voltage source. Applications to passive vibration control and active control authority enhancement are also presented and discussed. The finite element model is based on an equivalent single layer theory combined with a third-order shear deformation theory. A stress-voltage electromechanical model is considered for the piezoelectric materials fully coupled to the electrical circuits. To this end, the electrical circuit equations are also included in the variational formulation. Hence, conservation of charge and full electromechanical coupling are guaranteed. The formulation results in a coupled finite element model with mechanical (displacements) and electrical (charges at electrodes) degrees of freedom. For a Graphite-Epoxy (Carbon-Fibre Reinforced) laminate composite plate, a parametric analysis is performed to evaluate optimal locations along the plate plane (xy) and thickness (z) that maximize the effective modal electromechanical coupling coefficient. Then, the passive vibration control performance is evaluated for a network of optimally located shunted piezoelectric patches embedded in the plate, through the design of resistance and inductance values of each circuit, to reduce the vibration amplitude of the first four vibration modes. A vibration amplitude reduction of at least 10 dB for all vibration modes was observed. Then, an analysis of the control authority enhancement due to the resonant shunt circuit, when the piezoelectric patches are used as actuators, is performed. It is shown that the control authority can indeed be improved near a selected resonance even with multiple pairs of piezoelectric patches and active-passive circuits acting simultaneously.     

Multimode shunt damping of piezoelectric smart panel for noise reduction

Multimode shunt damping of piezoelectric smart panel is studied for noise reduction. Piezoelectric smart panel is a plate structure on which a piezoelectric patch is attached with an electrical shunt circuit. When an incidence sound is impinged on the panel structure, the structure vibrates and the attached piezoelectric patch produces an electrical energy, which can be effectively dissipated as heat via the electrical shunt circuit. Since the energy dissipation strongly depends on the vibration mode of the panel structure, many patches are required for multiple vibration modes. Instead of using multiple piezoelectric patches, a single piezoelectric patch is used in conjunction with a blocked shunt circuit for multimode shunt damping. Modeling, shunt parameter tuning, and implementation of the blocked shunt circuit along with an acoustic test of the panel are explained. A remarkable reduction of the transmitted noise was achieved for multiple modes of the panel. Since this technology has many merits in terms of compactness, low cost, robustness, and ease of installation, practical applications in many noise problems can be anticipated.     

Simulation and optimization of dynamic characteristics of piezoelectric smart structures

The paper deals with optimization of dynamic characteristics of smart structures based on piezoelectric materials with external electric circuits comprising resistance, capacitance and inductance. The dynamic parameters to be optimized are resonance frequencies and damping properties. For numerical estimation of the dynamic characteristics of the model system, a natural vibration problem of an electroviscoelastic solid with differing external electric circuits is proposed. Model examples are given to demonstrate the efficiency of the natural vibration problem in finding dynamically optimum piezoelectric smart structures with external electric circuits.     

压电瞬态响应在换能器声功率测量中的应用

探索一种简便的聚焦超声功率测量方法,利用压电陶瓷片直接接收超声信号,通过机电类比得到压电瞬态响应由压电片在声波作用力下引起受迫振动产生的电压响应与固有振动产生的高频衰减响应叠加而成,分析输出压电信号与换能器声功率之间的换算关系。对输出压电信号进行二次包络提取,获得表征声功率变化的电压幅度曲线,分别找出不同换能器驱动电压下包络曲线的最大峰值电压,将其平方值与声功率计所测声功率进行线性拟合,并对理论关系式中的比例系数进行标定。实验结果所得线性拟合度较高,且标定后所得声功率与声功率计所测值相对误差低于8.7%,证明了通过压电瞬态响应测量换能器声功率具有可行性。      

Placement and dimension optimization of shunted piezoelectric patches for vibration reduction

Passive structural vibration reduction by means of shunted piezoelectric patches is addressed in this paper. We present a strategy to optimize, in terms of damping efficiency, the geometry of piezoelectric patches as well as their placement on the host elastic structure. This procedure is based on the maximization of the modal electro-mechanical coupling factor (MEMCF) of the mechanical vibration mode to which the shunt is tuned. To illustrate the method, a general analytical model of a laminated beam is proposed. Two particular configurations are investigated: (i) a beam with two collocated piezoelectric patches connected in series or in parallel to the shunt and (ii) a cantilever beam with one patch. After a modal expansion, original closed-form solutions of the MEMCF are exhibited, which enables to compute optimal values for the placement, length and thickness of the piezoelectric patches that maximize the MEMCF. A dimensionless model is used so that this study can be used to design any smart beam, whatever be its dimensions. More general results about the coupling mechanisms between the piezoelectric patches and the host structure are also raised. In particular, it is found that the patches thickness is an essential parameter and that several configurations are possible, depending on the considered vibration mode. Experiments are also proposed to validate the model.     

Essentially nonlinear piezoelectric shunt circuits applied to mistuned bladed disks

An essentially nonlinear piezoelectric shunt circuit is proposed for the practical realization of nonlinear energy sink, and then applied to a mistuned bladed disk for blade vibration reduction. First, the global dynamics of a single degree-of-freedom linear mechanical oscillator, coupled to an essentially nonlinear shunted piezoelectric attachment, is studied. Under certain conditions, the nonlinear targeted energy transfer, i.e. a fast, passive energy transfer from the mechanical oscillator to the nonlinear attachment is observed. A numerical method, referred to as the variable-coefficient harmonic balance method, is developed to calculate quasi-periodic responses arising in the electromechanical system under harmonic forcing. Characterized by the nonexistence of a resonance frequency, the essentially nonlinear shunt circuit is able to work robustly over a broad frequency band with a smaller inductance requirement compared with the linear resonant shunt circuit.     

Coupled FEM/BEM for control of noise radiation and sound transmission using piezoelectric shunt damping

In this paper, we present a coupled finite element/boundary element method (FEM/BEM) for control of noise radiation and sound transmission of vibrating structure by passive piezoelectric techniques. The system consists of an elastic structure (with surface mounted piezoelectric patches) coupled to external/internal acoustic domains. The passive shunt damping strategy is employed for vibration attenuation in the low frequency range. The originality of the present paper lies in evaluating the classically used FEM/BEM methods for structural–acoustics problems when taking account smart systems at the fluid–structure interfaces.     

Electromechanical response of 2-2 layered piezoelectric composites: A micromechanical model based on the asymptotic homogenization method

A micromechanical model based on the asymptotic homogenization technique has been developed to predict the complete elastic, dielectric and piezoelectric properties of a general 2-2 layered piezoelectric composite where the constituent phases are elastically anisotropic and piezoelectrically active. Two classes of layered piezoelectric composites (i.e. longitudinally and transversely layered) are considered in two widely different ceramic- and polymer-based systems and their effective properties are obtained in the limits of both large-volume (i.e. bulk) and small-volume (i.e. thin-film) systems. It is demonstrated that: (i) in the bulk, ceramic–ceramic layered composite system, the elastic, piezoelectric, and dielectric properties of the composites vary linearly with volume fraction of the second phase, while in the bulk ceramic–polymer layered composite system, the corresponding properties vary non-linearly with volume fraction of the second phase; (ii) in the prismatic (thin-film) layered piezoelectric composite system, the non-vanishing, effective elastic, piezoelectric and dielectric properties vary linearly with the volume fraction of the second phase for both the longitudinally and transversely layered composite structures in the ceramic–ceramic and the ceramic–polymer composite systems; (iii) the ceramic–polymer piezoelectric layered composites that incorporate a low density polymeric phase with lower acoustic impedance generally exhibit enhanced piezoelectric coupling constants and lowered acoustic impedance; (iv) the longitudinally layered composites exhibit higher piezoelectric coupling constants and lower acoustic impedance compared to that of the transversely layered composites; and (v) the best combination of properties for applications such as hydrophones (i.e. the highest piezoelectric coupling constants and the lowest acoustic impedance) is obtained in the ceramic–polymer, longitudinally layered, thin-film, piezoelectric composites.     

基于弹性波超表面的Lamb波透射调控

根据广义Snell定律,该文提出了一种新型曲梁型弹性波超表面结构。通过该结构对入射波进行相位调制,实现了板中Lamb波(A0模态)的异常透射调控,从而实现了波的负折射、非对称传输、声聚焦等功能。进一步的研究结果显示,若将该类超表面结构贴置在完整的铝板表面,通过引入吸声材料(阻尼),在保证薄板完整性的同时,可以起到显著消除薄板和超表面透射波场叠加的作用。该方法实现了对完整板结构Lamb波透射方向的有效调控,也为弹性波超表面提供了新的研究思路。     

Active modal control simulation of vibro-acoustic response of a fluid-loaded plate

Active modal control simulation of vibro-acoustic response of a fluid-loaded plate is presented. The active modal control of the vibro-acoustic response is implemented using piezoelectric actuators/sensors. The active modal damping is added to the coupled system via negative velocity feedback. The feedback gain between the piezoelectric actuators/sensors for the modal control is obtained using the in-vacuo modal matrix and the incompressible fluid-loaded modal matrix. The modal control performance of structural vibration and acoustic radiation of a baffled plate is numerically studied. It is shown that the proposed method increases the modal damping ratio and achieves reduction in the mean square velocity and the sound power for given modes of the fluid-loaded plate.     

The influence of external tensile stress on surface elastic waves on piezoelectric ceramic plates

Experimental results on the output voltage via a propagating surface elastic wave and the convolution output of two oppositely propagating surface elastic waves on a piezoelectric ceramic plate are described as a function of external tensile stress. The convolution output increases with the cummulative load, while the output voltage via the surface elastic wave decreases. The variation of the output voltage is considered to be due to the change in nonlinearity that arises from the external load.     

Equivalent circuit with complex physical constants and equivalent-parameters-expressed dissipation factors of piezoelectric materials

The equivalent circuit with complex physical constants for a piezoelectric ceramic in thickness mode is established. In the equivalent circuit, electric components (equivalent circuit parameters) are connected to real and imaginary parts of complex physical coefficients of piezoelectric materials. Based on definitions of dissipation factors, three of them (dielectric, elastic and piezoelectric dissipation factors) are represented by equivalent circuit parameters. Since the equivalent circuit parameters are detectable, the dissipation factors can be easily obtained. In the experiments, the temperature and the stress responses of the three dissipation factors are measured.