Optimization of organic electrochemical transistors for sensor applications

Despite the recent interest in organic electrochemical transistors (OECTs) as chemical and biological sensors, little is known about the role that device architecture and materials parameters play in determining sensor performance. We use numerical modeling to establish design rules in two regimes of operation: We find that for operation as an ion‐to‐electron converter, the response of OECTs is maximized through the use of a gate electrode that is much larger than the channel or through the use of a nonpolarizable gate electrode. Improving the conductivity of the polymer and using a channel geometry that maximizes channel width and thickness, and minimizes channel length helps increase the response. For operation as an electrochemical sensor, the sensitivity is maximized in OECTs with gate electrodes that are smaller than their channels. The sensitivity can be improved by increasing the charge carrier mobility and the capacitance per unit area of the conducting polymer, and also its ability to be penetrated by ions from the electrolyte. A channel geometry that maximizes channel width and minimizes channel length also improves sensitivity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

以DNA为模板构造苯胺-DNA复合物纳米线和聚苯胺纳米导线

在溶液中, 以DNA为模板构造出了线性的苯胺-DNA复合物纳米线. 用压缩气流将得到的复合物纳米线拉直并固定到云母基底上. 用原子力显微镜(AFM)可观察到形貌规整的苯胺-DNA复合物纳米线. 苯胺单体在溶液中能从各个方向上组装到DNA分子上, 从而使DNA模板分子的表面包裹了一层苯胺. 以苯胺-DNA复合物纳米线为前驱体通过进一步化学氧化聚合得到了以DNA为模板的聚苯胺纳米导线.     

Polymer electrolyte-gated organic field-effect transistors: low-voltage, high-current switches for organic electronics and testbeds for probing electrical transport at high charge carrier density

We report the fabrication and extensive characterization of solid polymer electrolyte-gated organic field-effect transistors (PEG-FETs) in which a polyethylene oxide (PEO) film containing a dissolved Li salt is used to modulate the hole conductivity of a polymer semiconductor. The large capacitance (approximately 10 microF/cm2) of the solution-processed polymer electrolyte gate dielectric facilitates polymer semiconductor conductivities on the order of 103 S/cm at low gate voltages (<3 V). In PEG-FETs based on regioregular poly(3-hexylthiophene), gate-induced hole densities were 2 x 10(14) charges/cm2 with mobilities >3 cm2/V.s. PEG-FETs fabricated with gate electrodes either aligned or intentionally nonaligned to the channel exhibited dramatically different electrical behavior when tested in vacuum or in air. Large differences in ionic diffusivity can explain the dominance of either electrostatic charging (in vacuum) or bulk electrochemical doping (in air) as the device operational mechanism. The use of a larger anion in the polymer electrolyte, bis(trifluoromethanesulfonyl)imide (TFSI-), yielded transistors that showed clear current saturation and square law behavior in the output characteristics, which also points to electrostatic (field-effect) charging. In addition, negative transconductances were observed using the PEO/LiTFSI electrolyte for all three polymer semiconductors at gate voltages larger than -3 V. Bias stress measurements performed with PEO/LiTFSI-gated bottom contact PEG-FETs showed that polymer semiconductors can sustain high ON currents for greater than 10 min without large losses in conductance. Collectively, the results indicate that PEG-FETs may serve as useful devices for high-current/low-voltage applications and as testbeds for probing electrical transport in polymer semiconductors at high charge density.     

电化学制备有序聚苯胺纳米线阵列

以有序碳纳米管阵列电极为基底电极,在硫酸或高氯酸溶液中,分别探明不同电化学聚合方法以及苯胺单体浓度对聚苯胺形貌的影响. 结果表明：采用循环伏安法无法制备出聚苯胺纳米线;而应用恒电位法虽可制得聚苯胺纳米线,但纳米线不能形成有序阵列;只有应用恒电流方法,并且以高浓度苯胺的高氯酸溶液作为聚合溶液,方能制得有序聚苯胺纳米线阵列.     

Vibrational spectroscopy reveals electrostatic and electrochemical doping in organic thin film transistors gated with a polymer electrolyte dielectric

We apply attenuated total internal reflection Fourier transform infrared (ATR-FTIR) spectroscopy to directly probe active layers in organic thin film transistors (OTFTs). The OTFT studied uses the n-type organic semiconductor N-N'-dioctyl-3,4,9,10-perylene tetracarboxylic diimide (PTCDI-C8) and a polymer electrolyte gate dielectric made from poly(ethylene oxide) and LiClO4. FTIR spectroscopy of the device shows signatures of anionic PTCDI-C8 species and broad polaron bands when the organic semiconductor layer is doped under positive gate bias (VG). There are two distinctive doping regions: a reversible and electrostatic doping region for VG 2 V. On the basis of intensity loss of vibrational peaks attributed to neutral PTCDI-C8, we obtain a charge carrier density of 2.9 x 10(14)/cm2 at VG=2 V; this charge injection density corresponds to the conversion of slightly more than one monolayer of PTCDI-C8 molecules into anions. At higher gate bias voltage, electrochemical doping involving the intercalation of Li+ into the organic semiconductor film can convert all PTCDI-C8 molecules in a 30-nm film into anionic species. For comparison, when a conventional gate dielectric (polystyrene) is used, the maximum charge carrier density achievable at VG=200 V is approximately 4.5 x 10(13)/cm2, which corresponds to the conversion of 18% of a monolayer of PTCDI-C8 molecules into anions.     

Spatial control of p-n junction in an organic light-emitting electrochemical transistor

Low-voltage-operating organic electrochemical light-emitting cells (LECs) and transistors (OECTs) can be realized in robust device architectures, thus enabling easy manufacturing of light sources using printing tools. In an LEC, the p-n junction, located within the organic semiconductor channel, constitutes the active light-emitting element. It is established and fixated through electrochemical p- and n-doping, which are governed by charge injection from the anode and cathode, respectively. In an OECT, the electrochemical doping level along the organic semiconducting channel is controlled via the gate electrode. Here we report the merger of these two devices: the light-emitting electrochemical transistor, in which the location of the emitting p-n junction and the current level between the anode and cathode are modulated via a gate electrode. Light emission occurs at 4 V, and the emission zone can be repeatedly moved back and forth within an interelectrode gap of 500 μm by application of a 4 V gate bias. In transistor operation, the estimated on/off ratio ranges from 10 to 100 with a gate threshold voltage of -2.3 V and transconductance value between 1.4 and 3 μS. This device structure opens for new experiments tunable light sources and LECs with added electronic functionality.     

Integrated electrochemical transistor as a fast recoverable gas sensor

A new design of conductometric chemical sensors based on conducting polymers as chemosensitive elements was suggested. The sensor includes six electrodes. Four inner electrodes coated by chemosensitive polymer are used for simultaneous two- and four-point resistance measurements thus providing information on the bulk polymer resistance and on the resistance of the polymer/electrode contacts. Two outer electrodes wired to inner electrodes by polymeric electrolyte are used for electrical control of redox state of the chemosensitive polymer. The outer electrodes are connected to potentiostat as reference and counter electrodes. It allows us to control redox state of the inner (working) electrodes. This new measurement configuration, resembling chemosensitive electrochemical transistors, provides an internal test of the sensor integrity and an electrically driven sensor regeneration. It was tested as a sensor for the detection of nitrogen dioxide. Polythiophene or polyaniline was used as receptors. Cyclic voltammograms of these polymers on the sensor surface measured in air atmosphere were very similar to that measured in aqueous electrolyte. A control of conductivity of these chemosensitive polymers by electrical potential applied vs. incorporated reference electrode was demonstrated. This effect was used for the regeneration of the chemosensitive material after exposure to nitrogen dioxide: in comparison to usual chemiresistors displaying an irreversible behavior in such test even in the time scale of hours, a completely reversible sensor regeneration within few minutes was observed.     

Templateless assembly of molecularly aligned conductive polymer nanowires: a new approach for oriented nanostructures

Although oriented carbon nanotubes, oriented nanowires of metals, semiconductors and oxides have attracted wide attention, there have been few reports on oriented polymer nanostructures such as nanowires. In this paper we report the assembly of large arrays of oriented nanowires containing molecularly aligned conducting polymers (polyaniline) without using a porous membrane template to support the polymer. The uniform oriented nanowires were prepared through controlled nucleation and growth during a stepwise electrochemical deposition process in which a large number of nuclei were first deposited on the substrate using a large current density. After the initial nucleation, the current density was reduced stepwise in order to grow the oriented nanowires from the nucleation sites created in the first step. The usefulness of these new polymer structures is demonstrated with a chemical sensor device for H(2)O(2), the detection of which is widely investigated for biosensors. Finally, we demonstrated that controlled nucleation and growth is a general approach and has potential for growing oriented nanostructures of other materials.     

Conducting Polyaniline Nanowire Arrays Modified Electrode for High Performance Supercapacitor and Enhanced Catalysis of Nitrite Reduction

Vertically aligned conducting polymer nanowire arrays had great potential applications in supercapacitor electrode material and exhibited enhanced electrocatalytic behavior towards the reduction of nitrite. In this paper, a facial template‐free approach to synthesize large arrays of vertically aligned polyaniline (PANI) nanowires on electrochemically pretreated glassy carbon electrodes was reported by using a galvanostatic current method. The as‐prepared large arrays of PANI nanowires had very narrow diameters and were oriented perpendicular to the substrate, which was a benefit to the ion diffusion when being used as the supercapacitor electrode. The highest specific capacitance of PANI nanowire arrays was measured and kept high at a large charge‐discharge current density. Furthermore, it also can detect nitrite with ultrahigh sensitivity of 62.99 µA mM^?1 cm^?2 and a remarkable fast response time of less 1 s. The results indicated that the vertically aligned PANI nanowires could dramatically enhance the electrochemical performance.     

Polyoxometallates as inorganic templates for monolayers and multilayers of ultrathin polyaniline

The ability of a polyoxometallate (dodecamolybdophosphate) to form negatively charged monolayers on solid electrode surfaces is explored here to perform immobilization of monomeric (anilinium) units followed by electropolymerization within the monolayer. Consequently, hybrid films containing ultrathin conducting polymer (polyaniline) layers can be formed. By repeated and alternate treatments in solutions of dodecamolybdophosphate anions and anilinium cations, the amount of the material can be increased systematically in a controlled fashion leading to stable three-dimensional multilayer hybrid assemblies. The fact, that formal potentials of the dodecamolybdophosphate redox processes appear in the potential range where polyaniline is conductive, allows the system to operate reversibly and reproducibly in acid electrolyte.     

Synthesis, manipulation and conductivity of supramolecular polymer nanowires

The synthesis of supramolecular conducting nanowires can be achieved by using DNA and pyrrole. Oxidation of pyrrole in DNA-containing solutions yields a material that contains both the cationic polypyrrole (PPy) and the anionic DNA polymers. Intimate interaction of the two polymer chains in the self-assembled nanowires is indicated by FTIR spectroscopy. AFM imaging shows individual nanowires to be continuous, approximately 5 nm high and conformationally flexible. This feature allows them to be aligned by molecular combing in a similar manner to bare DNA and provides a convenient method for fabricating a simple electrical device by stretching DNA/PPy strands across an electrode gap. Current-voltage measurements confirm that the nanowires are conducting, with values typical for a polypyrrole-based material. In contrast to polymerisation of pyrrole on a DNA template in bulk solution, attempts to form similar wires by polymerisation at surface-immobilised DNA do not give a continuous coverage; instead, a beads-on-a-string appearance is observed suggesting that immobilisation inhibits the assembly process.     

Potentiometric monitoring DNA hybridization with polyaniline/Nylon-6 working electrode

Electrically conducting polymers are useful in various applications such as transistors and sensors. A potentiometric pH meter has been developed using polyaniline based working electrode and with improved selectivity using ionophores, the polyaniline based potentiometer has been applied to monitor various ions mainly in environmental applications. The polyaniline working electrode can be used to monitor not only the binding of a biological ionic macromolecules on polyaniline surface but also the binding of the adsorbed macromolecule with another macromolecule. We present first how the working electrode was prepared by polymerization of aniline in Nylon-6 matrix to provide the mechanical strength and then how single strand oligonucleotide probe binds with polyaniline surface. We then present how an electrode modification with mercaptoethanol results in a surface protected against non-specific binding and then finally we present the results of monitoring the complimentary strand binding leading to the formation of the double strand DNA. The text was submitted by the authors in English.     

聚苯胺/贵金属复合纳米材料的可控合成及催化应用

导电高分子/贵金属复合纳米材料因其在催化、传感、表面增强拉曼、光热治疗等诸多领域的应用前景而受到广泛关注.本文主要介绍我们课题组近年来利用可控合成策略制备的负载型和包埋型两种结构聚苯胺/贵金属复合纳米材料,以及利用复合纳米材料的结构和功能特性,对其在多相催化领域的应用、结构与催化性能之间构效关系的探索.     

Effects of Adsorbed Polyaniline on Redox Process on MoO3 Surface

The effects exhibited by adsorbed conducting polyaniline on the redox process on a molybdenum oxide surface were studied. Thermogravimetric results indicate a 4% polyaniline deposition. Cyclic voltammograms of the adsorbed polymer on MoO3 show that polyaniline exerts remarkable effects on the molybdenum blue oxidation-reduction process, with oxidation and reduction potentials of 0.33 and 0.18 V, respectively. This effect strongly enhances the electrode response, and can be used as an important tool in qualitative and/or quantitative determinations of molybdenum in solution as well as in any substrate. Copyright 1999 Academic Press.     

Bistability in doped organic thin film transistors

Organic thin film transitors (TFTs) with the conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid), PEDOT:PSS, as the active layer and cross-linked, layer-by-layer assembled poly(allylamine hydrochloride)/poly(acrylic acid) (PAH/PAA) multilayers as the gate dielectric layer were investigated. A combination of spectroscopic data and device performance characteristics was used to study the behavior of these TFT devices under a variety of controlled environmental test conditions. It was shown that depletion and recovery of the device can be induced to occur by a means that is consistent with the electrochemical oxidation and reduction of water contained in the film. In addition to acting as a reactant, moisture also acts as a plasticizer to control the mobility of other species contained in the film and thereby permits bistable operation of these devices. Raman spectroscopy was used to show that the observed device switching behavior is due to a change in the PEDOT doping level.     

Hybrid organic–inorganic nanocomposite materials for application in solid state electrochemical supercapacitors

Integration into a conducting polymer matrix to form a hybrid material is an effective way to harness the electrochemical activity of nanosized oxide clusters. By anchoring them into polyaniline, the reversible redox chemistry of the otherwise soluble polyoxometalate clusters can be combined with that of the conducting polymer and be put to work in energy storage applications. We present here preliminary results that show how the resulting hybrid polymer displays the combined activity of its organic and inorganic components to store and release charge in a solid state electrochemical capacitor device.     

聚合物场效应晶体管材料及其器件

导电聚合物因为可以大面积成膜、器件制作工艺简单,近年来在有机场效应晶体管的研究中受到越来越多的关注。有的聚合物场效应晶体管其性能已经可以和无定型硅晶体管相比拟。本文回顾了聚合物场效应晶体管的发展历程,概述了聚合物场效应晶体管的材料、器件制作、性能及工作机理。同时,对聚合物场效应晶体管的发展前景和目前存在的问题作了简单的总结。     

聚合物场效应晶体管材料及其器件

导电聚合物因为可以大面积成膜、器件制作工艺简单,近年来在有机场效应晶体管的研究中受到越来越多的关注.有的聚合物场效应晶体管其性能已经可以和无定型硅晶体管相比拟.本文回顾了聚合物场效应晶体管的发展历程,概述了聚合物场效应晶体管的材料、器件制作、性能及工作机理.同时,对聚合物场效应晶体管的发展前景和目前存在的问题作了简单的总结.     

Doping of polyaniline with polymeric dopants in solid state,gel state and solutions

Polystyrene with different degrees of sulfonation was empolyed as a polymeric dopant for polyaniline. The purpose of using a polymeric dopant is to avoid the migration of a small molecule dopant to increase stability of the doped complex. We applied the polymeric dopant to polyaniline in three different ways: in solid state, in solution and in gel state. In solid state, the conducting form was achieved only through a novel thermal doping method with the increase in temperature and pressure. In solution, the doping process was shown to be dependent on the nature of the solution and also on the molecular weight of the polymer. In the gel form of polyaniline, a polymeric dopant with a surprising low degree of sulfonation was found to be successful in the doping process.     

Fabrication of organic thin-film transistors using layer-by-layer assembly

Layer-by-layer assembly is presented as a deposition technique for the incorporation of ultrathin gate dielectric layers into thin-film transistors utilizing a highly doped organic active layer. This deposition technique enables the fabrication of device structures with a controllable gate dielectric thickness. In particular, devices with a dielectric layer comprised of poly(allylamine hydrochloride)/poly(acrylic acid) (PAH/PAA) bilayer films were fabricated to examine the properties of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as the transistor active layer. The transistor Ion/off ratio and switching speed are shown to be controlled by the gate bias, which is dependent upon the voltage applied and the number of bilayers deposited for the gate dielectric. The devices operate in the depletion mode as a result of dedoping of the active layer with the application of a positive gate bias. The depletion and recovery rate are highly dependent on the level of hydration in the film and the environment under which the device is operated. These observations are consistent with an electrochemical dedoping of the conducting polymer during operation.