Aromatic polyisophthalamides with oxybenzoyl pendent groups

A series of polyisophthalamides containing pendent oxybenzoyl groups were prepared from 5-oxybenzoyl-isophthaloyl chloride and aromatic diamines. The analogous unsubstituted polyisophthalamides were also prepared in order to compare the two series and to determine the effect of oxybenzoyl pendent groups on the properties of aromatic polyamides. The modified polymers exhibited better solubility than, and approximately the same glass transition temperatures (in the range 260–290°C) as, the parent unsubstituted polymers. The mechanical strength of polymer films was affected only to a small extent by the presence of side groups, but the thermal resistance was negatively affected, with the result that polyisophthalamides with oxybenzoyl pendent groups began to decompose at about 360°C (TGA), 60–100°C lower than the unsubstituted polyisophthalamides. By means of an appropriate thermal treatment, crosslinking of the modified polymers was achieved and their thermal resistance significantly enhanced.     

Preparation and characterization of aromatic polyamides based on ether-sulfone-dicarboxylic acids

Two ether-sulfone-dicarboxylic acids, 4,4′-[sulfonylbis(2,6-dimethyl-1,4-phenylene)dioxy]dibenzoic acid (Me- III ) and 4,4′-[sulfonylbis(1,4-phenylene)dioxy]-dibenzoic acid ( III ), were prepared by the fluorodisplacement of 4,4′-sulfonylbis(2,6-dimethylphenol) and 4,4′-sulfonyldiphenol with p-fluorobenzonitrile, and subsequent alkaline hydrolysis of intermediate dinitriles. Using triphenyl phosphite (TPP) and pyridine as condensing agents, aromatic polyamides containing ether and sulfone links were prepared by the direct polycondensation of the dicarboxylic acids with various aromatic diamines in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The inherent viscosities of the resulting polymers were above 0.4 dL/g and up to 1.01 dL/g. Most of the polyamides were readily soluble in polar solvents such as NMP, N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), and dimethyl sulfoxide (DMSO), and afforded tough and transparent films by solution-casting. Most of the polymers showed distinct glass transition on their differential scanning calorimetry (DSC) curves, and their glass transition temperatures (T_g) were recorded between 212–272°C. The methyl-substituted polyamides showed slightly higher T_gs than the corresponding unsubstituted ones. The results of the thermogravimetry analysis (TGA) revealed that all the polyamides showed no significant weight loss before 400°C, and the methyl-substituted polymers showed lower initial decomposition temperatures than the unsubstituted ones. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2421–2429, 1997     

New organosoluble and thermally stable poly(amide‐imide)s with benzoxazole or benzothiazole pendent groups: synthesis and characterization

Two new benzoxazole or benzothiazole‐containing diimide‐dicarboxylic acid monomers, such as 2‐[3,5‐bis(N‐trimellitimidoyl)phenyl]benzoxazole ( 2 _o ) or 2‐[3,5‐bis(N‐trimellitimidoyl)phenyl]benzothiazole ( 2 _s ) were synthesized from the condensation reaction between 3,5‐diaminobenzoic acid and 2‐aminophenol or 2‐aminothiophenol in polyphosphoric acid (PPA) with subsequent reaction of trimellitic anhydride in the presence of glacial acetic acid, respectively, and two new series of modified aromatic poly(amide‐imide)s were prepared. This preparation was done with pendent benzoxazole or benzothiazole units from the newly synthesized diimide‐dicarboxylic acid and various aromatic diamines by triphenyl phosphite‐activated polycondensation. In addition, the corresponding unsubstituted poly(amide‐imide)s were prepared under identical experimental conditions for comparative purposes. Characterization of polymers was accomplished by inherent viscosity measurements, FT‐IR, UV–visible, ¹H‐NMR spectroscopy and thermogravimetry. The polymers were obtained in quantitative yields with inherent viscosities between 0.39 and 0.81 dl g^?1. The solubilities of modified poly(amide‐imide)s in common organic solvents as well as their thermal stability were enhanced compared to those of the corresponding unmodified poly(amide‐imide)s. The glass transition temperature, 10% weight loss temperature, and char yields at 800°C were, respectively, 7–26°C, 17–46°C and 2–5% higher than those of the unmodified polymers. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and properties of aromatic polyamides with oligobenzamide pendent groups. I. Poly-5-(4-benzoylamino-1-benzoylamino)isophthalamides

A series of polyisophthalamides having pendent oligomeric benzamide groups were prepared by the Yamazaki reaction from common aromatic diamines and 5-(4-benzoylamino-1-benzoylamino)isophthalic acid. The latter was synthesized from 5-aminoisophthalic acid in a three-step synthesis by successive incorporation of benzamido groups. The new polymers were characterized by NMR, DSC, TGA, and WAXD and the properties were compared to those of corresponding unsubstituted polyisophthalamides. All of the polymers were essentially amorphous and their T_gs were about 20°C higher than the reference polymers. Initial thermal decomposition temperatures ranged from 375 to 420°C. All of the polymers were soluble in aprotic polar solvents without added salts. Properties of particular note were: the water uptake, which was particularly high, ranging from 7.5 to 18.2%, and the temporary insolubilization in concentrated sulfuric acid of films of the polymers heated for a short time to ≥ 200°C. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of new soluble polyamides containing phthalimide pendent group

A dicarboxylic acid monomer, 5-phthalimidoisophthalic acid, containing a phthalimide pendent group was prepared by the condensation of 5-aminoisophthalic acid and phthalic anhydride in glacial acetic anhydride. The monomer was reacted with various aromatic diamines to produce polyamides using triphenyl phosphite and pyridine as condensing agents. These polyamides were produced with inherent viscosities of 0.64–1.14 dL · g⁻¹. All the polymers, characterized by wide-angle X-ray diffraction, revealed an amorphous nature resulting from the presence of the bulky pendent group. These polyamides exhibited excellent solubility in a variety of solvents such as N- methyl-2-pyrrolidinone, N,N-dimethylacetamide (DMAc), N,N-dimethylformamide, dimethyl sulfoxide, pyridine, and cyclohexanone. These polyamides showed glass-transition temperatures (T_g's) between 247 and 273 °C (by DSC) and 248 and 337 °C (by a dynamic mechanical analyzer). The thermogravimetric analytic measurement revealed the decomposition temperature at 10% weight-loss temperatures (Td₁₀) ranging from 442 to 530 °C in nitrogen. The polyamides containing phthalimide groups exhibited higher T_g and Td₁₀ values than those having no phthalimide groups. Transparent, tough, and flexible films of these polyamides could be cast from the DMAc solutions. These casting films had tensile strengths ranging from 81 to 126 MPa, elongations at break ranging from 7 to 13%, and tensile moduli ranging from 2.0 to 2.9 GPa. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1557–1563, 2001     

Novel thermally stable triarylamine‐containing aromatic polyamides bearing anthrylamine chromophores for highly efficient green‐light‐emitting materials

A series of novel polyamides with pendent anthrylamine units were prepared via the direct phosphorylation polycondensation from various diamines and the anthrylamine‐based aromatic dicarboxylic acid, 9‐[N,N‐di(4‐carboxyphenyl)amino]anthracene (4). The aromatic polyamides had useful levels of thermal stability associated with relatively high softening temperatures (T_s) (290–300 °C), 10% weight‐loss temperatures (T_d¹⁰) nearly in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 60%. These aromatic polyamides I exhibited highly photoluminescence quantum yield in NMP solution ranges from 55% for Ia to 74% for Ie due to the introduction of anthrylamine chromophores. Cyclic voltammograms of the polyamide films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited one oxidation and reduction couples (E_onset) around 1.10 and ?1.50 V versus Ag/AgCl in acetonitrile (CH₃CN) and DMF solutions, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7354–7368, 2008     

Synthesis and characterization of novel aromatic polyamides containing 3-trifluoromethyl-substituted triphenylamine

A new 3-trifluoromethyl-substituted triphenylamine-containing aromatic diacid monomer, N,N-bis(4-carboxyphenyl)-3-trifluoromethylaniline, was prepared by the substitution reaction of 3-trifluoromethylaniline with 4-fluorobenzonitrile, followed by alkaline hydrolysis of the dinitrile intermediate. Novel aromatic polyamides with 3-trifluoromethyl-substituted triphenylamine moieties were prepared from the diacid and various aromatic diamines via the direct phosphorylation polycondensation. All the polyamides were amorphous and readily soluble in many polar organic solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone, and could be solution-cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability with relatively high glass-transition temperatures (258–327°C), 10% weight-loss temperatures above 500°C, and char yields higher than 60% at 800°C in nitrogen. These polymers had low dielectric constants of 3.22–3.70 (100 Hz), low moisture absorption in the range of 1.75–2.58%, and high transparency with an ultraviolet–visible absorption cut-off wavelength in the 375–395 nm range. Cyclic voltammograms of the polyamide films cast onto an indium tin oxide coated glass substrate exhibited a reversible oxidation redox couple with oxidation half-wave potentials (E_1/2) of 0.95–1.00 V vs. Ag/AgCl in an acetonitrile solution.     

Syntheses and properties of aromatic polyamides and polyimides derived from 9,9-bis[4-(p-aminophenoxy)phenyl]fluorene

9,9-Bis[4-(p-aminophenoxy)phenyl]fluorene ( II ) was used as a monomer with various aromatic dicarboxylic acids and tetracarboxylic dianhydrides to synthesize polyamides and polyimides, respectively. The diamine II was derived by a nucleophilic substitution of 9,9-bis(4-hydroxyphenyl)fluorene with p-chloronitrobenzene in the presence of K₂CO₃ and then hydro-reduced. Polyamides IV _a-g having inherent viscosities of 0.73–1.39 dL/g were prepared by the direct polycondensation of the diamine II with various aromatic diacids using triphenyl phosphite and pyridine as condensing agents. All the aromatic polyamides were amorphous and readily soluble in various polar solvents such as N,N-dimethylacetamide, N,N-dimethylformamide, dimethylsulfoxide, and N-methyl-2-pyrrolidone. Transparent and flexible films of these polymers could be cast from the DMAc solutions. These aromatic polyamides had glass transition temperatures in the range of 283–309°C and 10% weight loss occurred up to 460°C. The polyimides were synthesized from diamine II and various aromatic dianhydrides via the two-stage procedure that included ring-opening poly-addition in DMAc to give poly(amic acid)s, followed by thermal or chemical conversion to polyimides. The poly(amic acid)s had inherent viscosities of 0.62–1.78 dL/g, depending on the dianhydrides. Most of the aromatic polyimides obtained by chemical cyclization were found to be soluble in NMP. These polyimides showed almost no weight loss up to 500°C in air or nitrogen atmosphere. © 1993 John Wiley & Sons, Inc.     

High Glass Transition and Optical Transparency of Novel Organosoluble Polyamides Containing 4‐tert‐‐Butyltoluene Moiety

A series of novel polyamides 3a – 3d containing 4‐tert‐butyltoluene moiety, were prepared using the phosphorylation polycondensation technique. FT‐IR and ¹H NMR techniques were used to investigate the chemical structures of 3a–3d . The results confirmed that they agreed with the proposed structures for 3a – 3d completely. The 3a – 3d had inherent viscosities ranging from 0.71 to 1.67 dL·g⁻¹. All the polyamides showed excellent solubility, with the dissolvability at a concentration of 10 wt% in most amide polar solvents. Flexible and tough polyamide films could be prepared by casting from DMAc (N,N‐dimethylacetamide) solvent. Their films were nearly colorless and exhibited high optical transparency, with the UV cutoff wavelength in the range of 346–363 nm and transmittance higher than 80% at 450 nm. They also exhibited high glass transition temperatures in the range of 310–343°C and the onset decomposition temperatures in the range of 435–462°C in nitrogen atmosphere. Meanwhile, these polyamide films possess good mechanical properties with tensile strengths of 76.4–86.1 MPa and elongations at break of 11.2%–27.3%. Due to those properties, these polyamides could be considered as photoelectric and microelectronic materials.     

Syntheses and properties of aromatic polyamides and polyimides based on N-phenyl-3,3-bis[4-(p-aminophenoxy) phenyl] phthalimidine

N-Phenyl-3,3-Bis[4-(p-aminophenoxy)phenyl] phthalimidine ( II ) was used as a monomer with various aromatic dicarboxylic acids and tetracarboxylic dianhydrides to synthesize polyamides and polyimides, respectively. The diamine II was derived by a nucleophilic substitution of N-phenyl-3,3-bis(4-hydroxyphenyl) phthalimidine with p-chloronitrobenzene in the presence of K₂CO₃ and then hydro-reduced. Polyamides IV _a-g having inherent viscosities of 0.55–1.64 dL/g were prepared by the direct polycondensation of the diamine II with various aromatic diacids using triphenyl phosphite and pyridine as condensing agents. All the aromatic polyamides were amorphous and readily soluble in various polar solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide, dimethylsulfoxide, and N-methyl-2-pyrrolidone (NMP). Transparent and flexible films of these polymers could be cast from the DMAc solutions. These aromatic polyamides had glass transition temperatures in the range of 293–319°C and 10% weight loss occurred up to 480°C. The polyimides were synthesized from diamine II and various aromatic dianhydrides via the two-stage procedure that included ring-opening polyaddition in DMAc to give poly(amic acid)s, followed by thermal or chemical conversion to polyimides. Most of the aromatic polyimides obtained by chemical cyclization were found to be soluble in NMP, m-cresol, and o-chlorophenol. These polyimides showed almost no weight loss up to 500°C in air or nitrogen atmosphere. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of new polyamides derived from 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene and aromatic dicarboxylic acids

The diamine 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene, containing symmetric, bulky di-tert-butyl substituents and a flexible ether unit, was synthesized and used to prepare a series of polyamides by the direct polycondensation with various aromatic dicarboxylic acids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.32–1.27 dL g⁻¹. Most of these polyamides, except II _a , II _d , and II _e , showed an amorphous nature and dissolved in polar solvents and less polar solvents. Polyamides derived from 4,4′-sulfonyldibenzoic acid, 4,4′-(hexafluoro-isopropylidene)dibenzoic acid, and 5-nitroisophthalic acid were even soluble in a common organic solvent such as THF. Most polyamide films could be obtained by casting from their N,N-dimethylacetamide (DMAc) solutions. The polyamide films had a tensile strength range of 49–78 MPa, an elongation range at break of 3–5%, and a tensile modulus range of 1.57–2.01 GPa. These polyamides had glass transition temperatures ranging between 253 and 276°C, and 10% mass loss temperatures were recorded in the range 402–466°C in nitrogen atmosphere. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1069–1074, 1998     

METAL ADHESIVE PROPERTIES OF POLYAMIDES HAVING 4,5-DI(1,4-PHENYLENE)-IMIDAZOLEDIYL STRUCTURE

Polyamides were synthesized by the direct polycondensation of aromatic diamines containing 4,5-imidazolediyl structure with aliphatic dicarboxylic acids, and the metal adhesive properties of these polymaides were studied. The inherent viscosity of the obtained polyamides was in the range of 0.28 to 0.71 dl g^?1. The decomposition temperatures (T _ds) of the obtained polyamides were above 400°C and their glass transition temperatures (T _gs) were from 168 to 198°C. These polyamides also showed good solubilities in polar solvents, such as N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc) and formic acid. A standard tensile test was performed in order to examine the adhesive property of these polyamides for stainless steel, and the obtained polyamides showed excellent tensile strengths, e.g. polyamide P1s derived from 4,5-di(4-aminophenyl)imidazole (DAPI) and sebasic acid had values of 212 kgf cm^?2 at 20°C, 183 kgf cm^?2 at 120°C, and 133 kgf cm^?2 at 180°C. A commercially available epoxy resin was also examined, and showed great tensile strength at 20°C. However, the strength of the epoxy resin was found to decrease with increasing temperature, whereas polyamide having 4,5-imidazolediyl structure retains its strength at temperatures of up to 180°C. In addition, the polyamide was also derived from 4,4″-diamino-o-terphenyl(DAOT) (rather than DAPI) and sebasic acid, and the properties of the polyamides derived, respectively from DAPI and DAOT were compared.     

Syntheses and properties of novel fluorinated polyamides based on a bis(ether‐carboxylic acid) or a bis(ether amine) extended from bis(4‐hydroxyphenyl)phenyl‐2,2,2‐trifluoroethane

Two series of novel fluorinated aromatic polyamides were prepared from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic dicarboxylic acids with the phosphorylation polyamidation technique. These polyamides had inherent viscosities ranging from 0.51 to 1.54 dL/g that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 36,200–80,000 and 17,200–64,300, respectively. All polymers were highly soluble in aprotic polar solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some could even be dissolved in less‐polar solvents like tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 76–94 MPa and initial moduli of 1.70–2.22 GPa. Glass‐transition temperatures (T_g's) and softening temperatures of these polyamides were observed in the range of 185–268 °C by differential scanning calorimetry or thermomechanical analysis. Decomposition temperatures (T_d's) for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. Almost all the fluorinated polyamides displayed relatively higher T_g and T_d values than the corresponding nonfluorinated analogues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 420–431, 2003     

Thermostable laminating resins based on aromatic diketone bis- and tetramaleimides

Twelve structurally different bis- and tetramaleimides were synthesized by Friedel–Crafts reaction between 4-maleimido-benzoylchloride or 3,5-bismaleimido-benzoylchloride and various aromatic reagents. They were characterized by infrared (IR) and proton nuclear magnetic resonance (¹H-NMR) spectroscopy. Crosslinked resins were obtained by curing the monomers at 250°C/6 h. Thermal characterization of monomers and cured resins was accomplished by differential thermal analysis (DTA), dynamic thermogravimetric analysis (TGA), and isothermal gravimetric analysis (IGA). Tetramaleimides were polymerized at lower temperatures than did the respective bismaleimides. The cured resins were stable up to 317–385°C in N₂ atmosphere and formed an anaerobic char yield of 52–66% at 800°C.     

Synthesis and properties of new aromatic polyisophthalamides with adamantylamide pendent groups

A new diacid monomer containing a pendent adamantyl ring was reacted with various aromatic diamines to prepare novel aromatic polyisophthalamides (PIPAs). The polymers were obtained in high yield and high molecular weight by the Yamazaki‐Higashi phosphorylation method of polycondensation. Inherent viscosities ranged from 0.40 to 0.82 dL/g, which corresponds to weight‐average and number‐average molecular weights (GPC) in the range 21,000–63,000 g/mol and 9000–31,000 g/mol, respectively. The polymers were essentially amorphous and soluble in a variety of polar aprotic solvents, and they afforded transparent, creasable films by the solution‐casting method. The great size of the polyhedral adamantyl moiety brought about a significant restriction of segmental mobility, which translated into a strong increase of T_g, so that very high glass transition temperatures were observed, in the range 335–370 °C (DSC), which are 70–90 °C above the glass transition temperatures of homologous PIPAs without pendent groups. Thus, it can be stated that these adamantyl containing polyamides are among the soluble aromatic PIPAs with highest T_g ever described. Conversely, the initial decomposition temperature, as measured by thermogravimetric analysis, was about 400 °C, which is lower by 40–70° than that of unsubstituted counterparts. Polymer films exhibited good mechanical properties, with tensile strengths over 65 MPa and tensile moduli between 2.0 and 2.6 GPa. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1743–1751, 2010     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Synthesis and properties of aromatic polyamides based on 4,4′-(2,7-naphthalenedioxy)dibenzoic acid

4,4′-(2,7-Naphthalenedioxy)dibenzoic acid, a new aromatic dicarboxylic acid monomer, was prepared starting from 2,7-dihydroxynaphthalene and p-fluorobenzonitrile in three steps. Using triphenyl phosphite (TPP) and pyridine as condensing agents, a series of novel aromatic polyamides were synthesized by the direct polycondensation of the diacid monomer and aromatic diamines in N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The resulting polyamides had inherent viscosities ranging from 0.48 to 0.67 dL/g. Most of these polyamides were readily soluble in polar solvents, such as NMP and N,N-dimethylacetamide (DMAc). Transparent, flexible, and tough films were cast from their DMAc solutions. They had tensile strengths of 65–70 MPa, elongations to break of 5–7%, and initial moduli of 1.4–1.6 GPa. Most of these polymers proved to be amorphous, with glass transition temperatures in the range between 143–227°C. Thermogravimetric analysis (TG) showed that all the polyamides were stable up to 450°C in both air and nitrogen atmospheres. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1469–1478, 1997     

Laminating resins obtained from 2,2′-(1,4-phenylenedivinylene)bispyridine bismaleimides and maleimide-terminated styrylpyridine prepolymers

A new bismaleimide (2a) , biscitraconimide (2b) , and bisnadimide (4) were synthesized by reacting 2-amino-6-methylpyridine with an equimolar amount of maleic, citraconic, or nadic anhydride, respectively, and then with a half molar amount of 1,4-benzenedicarbaldehyde in the presence of acetic anhydride. They, as well as the intermediate amic acids ( 1a, 1b, and 3 ) were characterized by IR and ¹H-NMR spectroscopy. The DTA thermograms showed that crosslinking of polymer precursors started at 180–212°C. The crosslinked resins obtained from 2a and 2b were stable up to 300–313°C and afforded anaerobic char yield of 53–60% at 800°C. The cured resin of 4 was less thermostable. In addition, end-capping of styrylpyridine prepolymers was accomplished by reacting 2,6-dimethylpyridine (n mol) with 1,4-benzenedicarbaldehyde (n + 1 mol) in acetic anhydride to yield a formyl-terminated styrylopyridine prepolymer. The latter reacted with the maleamic acid 1a (2 mol) to afford a series of maleimide-terminated styrylpyridine prepolymers MTSOs. They showed lower curing temperatures than did the ordinary poly(styrylpyridine). Their cured resins did not lose weight up to 310–344°C both in N₂ or air and afforded anaerobic char yield of 66-72% at 800°C.     

Soluble and fusible polyamides and polyimides containing pyrazoline moieties and their crosslinking to heat-resistant resins

3-(4-Aminophenyl)-5-(3-aminophenyl)-2-pyrazoline as well as the 1-acetyl- or 1-benzoyl-substituted derivatives of this compound were synthesized and used for preparing a new series of polyamides and polyimides. Characterization of polymers was accomplished by inherent viscosity, ¹H-NMR, ¹³C-NMR, x-ray, DTA, TMA, TGA, and isothermal gravimetric analysis. The properties of polymers were correlated with their chemical structures. They were amorphous or microcrystalline and soluble in polar aprotic solvents, CCl₃COOH, and m-cresol. The polyamides showed an excellent solubility being soluble even in o-dichlorobenzene, 1,2-dichloroethane, and chloroform. The polymers displayed T_g at 127–163°C and softening at 150–195°C. The polyamide bearing unsubstituted pyrazoline moieties was remarkably more hydrophilic than those containing 1-acetyl- or 1-benzoyl-substituted pyrazoline segments. Upon curing, crosslinked polymers were obtained and their thermal stability was evaluated. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1353–1361, 1997     

Synthesis and characterization of soluble aromatic polyamides from 2,5-bis(4-aminophenyl)—3,4-diphenylthiophene and aromatic diacid chlorides

New soluble aromatic polyamides with inherent viscosities of 1.0–1.7 dL/g were prepared by the low temperature solution polycondensation of 2,5-bis(4-aminophenyl)—3,4-diphenylthiophene, bis(4-aminophenyl) ether, and aromatic diacid chlorides in N,N-dimethylacetamide. The polyamides and copolyamides are generally soluble in amide-type solvents. They have glass transition temperatures in the range of 280–325°C and showed no weight loss below 390°C on thermogravimetry curves in both air and nitrogen atmospheres.