Mg2Sn电子结构及热力学性质的第一性原理计算

采用基于第一性原理的赝势平面波方法系统地计算了Mg₂Sn基态的电子结构、弹性常数和热力学性质.计算结果表明Mg₂Sn的禁带宽度为0.1198eV.运用线性响应方法确定了声子色散关系和态密度,得出Mg₂Sn的热力学性质如等容比热和德拜温度.计算Mg₂Sn的热导率并与实验数据相比较. 关键词： 第一性原理 电子结构 弹性常数 热力学性质     

Mg-Sn-Si合金中Mg2(Si,Sn)复合相的结构与性能研究

研究了铸态Mg-Sn-Si合金中Mg₂(Si,Sn)复合相的结构、 特性以及该相对Mg-Sn-Si合金变质作用的影响. 结果表明: Sn原子能取代Mg₂Si中的部分Si生成Mg₂(Si,Sn)复合相, 该三元相与Mg₂Si, Mg₂Sn相的结构相同, 属于面心立方结构, Mg₂(Si,Sn)相的元素含量并不固定, 在Si富集区形成的Mg₂(Si,Sn)相中, Si元素含量高, 在Si贫乏区形成的Mg₂(Si,Sn)相中, Si元素含量低. Si含量较多的Mg₂(Si,Sn)相性能与Mg₂Si相接近, Sn含量较多的Mg₂(Si,Sn)相性能与Mg₂Sn相接近, 实验中发现Mg₂(Si,Sn)复合相的纳米硬度、 弹性模量与维氏硬度等物理性能介于Mg₂Si与Mg₂Sn之间, Mg₂(Si,Sn)相对汉字状Mg₂Si相的变质处理起到桥梁作用. 关键词： Mg-Sn-Si合金 2Si')" href="#">Mg₂Si 2Sn')" href="#">Mg₂Sn 2(Si,Sn)复合相')" href="#">Mg₂(Si,Sn)复合相     

第一性原理研究Mg2 Si同质异相体的结构、电子结构和弹性性质

在第一性原理框架下,采用赝势平面波方法研究了三种Mg₂Si同质异相体的晶胞结构、电子结构和弹性性质随压强的变化关系.研究发现,反萤石结构Mg₂Si、反氯铅矿结构Mg₂Si和Ni₂In型Mg₂Si分别在压强为0-7 GPa,7.5-20.2 GPa和21.9-40 GPa范围内能够保持结构稳定.计算获得了不同压强下Mg₂Si的弹性常数、体模量、剪切模量、杨氏模量、泊松比和各向异 关键词： 态密度 电子结构 弹性常数 第一性原理     

Elastic constants and thermodynamic properties of Mg2SixSn1-x from first-principles calculations

<正>This paper stuides the elastic constants and some thermodynamic properties of Mg₂Si_xSn_n-1（x=0,0.25,0.5, 0.75,1） compounds by first-principles total energy calculations using the pseudo-potential plane-waves approach based on density functional theory,within the generalized gradient approximation for the exchange and correlation potential. The elastic constants of Mg₂Si_xSn_n-1 were calculated.It shows that,at 273 K,the elastic constants of Mg₂Si and Mg₂Sn are well consistent with previous experimental data.The isotropy decreases with increasing Sn content.The dependences of the elastic constants,the bulk modulus,the shear modulus and the Debye temperatures of Mg₂Si and Mg₂Si_0.5Sn_0.5 on pressure were discussed.Through the quasi-harmonic Debye model,in which phononic effects were considered,the specific heat capacities of Mg₂Si_xSn_1-x at constant volume and constant pressure were calculated.The calculated specific heat capacities are well consistent with the previous experimental data.     

M2Sn17(M=Ni，Mn)及其阴离子的几何结构、电子结构和磁性的计算研究

采用密度泛函理论(density functional theory, DFT)中的广义梯度近似(generalized gradient approximation, GGA) 对Ni₂Sn₁₇，Mn₂Sn₁₇，［Ni₂Sn₁₇］^4-和［Mn₂Sn₁₇］^2-三种同分异构体的几何结构、电子 关键词： 2Sn₁₇')" href="#">Ni₂Sn₁₇ 2Sn₁₇')" href="#">Mn₂Sn₁₇ 几何结构 电子结构和磁性 密度泛函理论     

(Ti1-xNbx)5AlC4(x=0.4, 0.75, 1)固溶体系的第一性原理研究

采用第一性原理计算,通过投影缀加波(PAW)和广义梯度近似(GGA)研究三元层状化合物(MAX) Ti₅AlC₄中Nb多比例掺杂M位元素.通过计算该固溶体系的声子谱、生成焓和弹性常数,讨论了(Ti_1-xNb_x)₅AlC₄固溶体系的稳定性,得到了三种稳定的结构：(Ti_0.6Nb_0.4)₅AlC₄、(Ti_0.25Nb_0.75)₅AlC₄和Nb₅AlC₄,即(Ti_1-xNb_x)₅AlC₄(x=0.4, 0.75, 1)固溶体系.Bader电荷、局域电荷密度、态密度表明该固溶体系呈现出金属特性,且电导率随着掺杂比例的增大,电荷不断转移,电导率增强.通过计算不同掺...     

Dy-Sn二元系合金相图

本工作用X射线粉末照相法和差热分析法测定了Dy-Sn二元系合金相图。Dy-Sn系存在九个金属间化合物,其中DySn₂,Dy₅Sn₃,Dy₅Sn₄以及Dy₁₁Sn₁₀已有结构报道,其余五个化合物尚未见报道,它们是:Dy₂Sn,DySn,Dy₈Sn₉,Dy₄Sn₇和DySn₄存在四个共晶反应,六个包晶反应。化合物Dy₂Sn,DySn,Dy₄Sn₇分别在1237℃,1222℃及1154℃同成份熔化,Dy₅Sn₃,Dy₅Sn₄,Dy₁₁Sn₁₀,Dy₈Sn₉,DySn₂及DySn₄则分别在包晶反应温度,1140℃、1160℃,1175℃,1134℃,738℃以及442℃分解,富Dy区在1182℃存在一熔晶转变。DySn₄与Sn互不溶解。α-Dy中最大含Sn量大约为5wt％,β-Dy中最大含Sn量大约为7wt%。 关键词：     

第一性原理计算Mo浓度对Mo掺杂BiVO4光催化性能的影响

本文利用基于密度泛函理论的第一性原理研究了不同浓度的Mo掺杂BiVO₄的V位的电子结构、光学性质和光催化性能.缺陷形成能的计算结果说明BiMo_xV_1-xO₄(x=0.0625, 0.125, 0.25)三种掺杂体系都是可以稳定存在的.电子结构计算结果表明：BiMo_xV_1-xO₄(x=0, 0.0625, 0.125, 0.25)四种体系的带隙分别为2.123 eV,2.142 eV,2.160 eV和2.213 eV.掺杂BiVO₄体系的带隙值均大于本征BiVO₄,且带隙随着Mo浓度的增加而增大. BiMo_xV_1-xO₄(x=0.0625, 0.125, 0.25)三种掺杂体系的能带结构全部向低能量区域移动,导致掺杂体系导带底越过费米能级,Mo掺杂BiVO₄后具...     

Mg原子修饰的封闭型六硼烷B6H62-储氢性质的研究

利用密度泛函理论的方法研究了Mg原子修饰的封闭型六 硼烷B₆H₆^2-吸附氢的性能. Mg可以稳定地结合在B₆H₆^2-上, 它可以吸附六个氢分子. 电荷转移所导致的Mg周围电场的增强和体系更大的偶极矩使 得MgB₆H₆^2-比MgB₆H₆具有更好的储氢性能, 储氢密度达到11.1 wt%, 氢分子的平均结合能在0.23 eV/H₂至0.34 eV/H₂之间. 结果表明可以通过控制金属-有机物体系的电荷态来增强电场, 进而改善其储氢性能. 关键词： 6H₆^2-团簇')" href="#">MgB₆H₆^2-团簇 密度泛函理论(DFT) 储氢性能 电荷态     

高压下Nb3Sn单晶的超导相转变

研究高压下Nb₃Sn单晶的超导相转变行为对探究力学变形诱导的材料超导性能弱化机理有重要意义。通过分子动力学模拟研究了Nb₃Sn单晶在高压下的原子尺度变形和晶体结构变化,在此基础上,建立了高压下Nb₃Sn单晶的超导相转变模型,模型预测结果与实验观测结果吻合较好。结果表明:静水压作用下,Nb₃Sn单晶体发生了明显的晶格畸变,但晶体结构保持完整;压力诱导的费米面上电子态密度的变化在高压下Nb₃Sn单晶体超导相转变中起主导作用。所得研究结果为研究高压下Nb₃Sn多晶体以及复合多晶体的相转变行为奠定了基础,同时有助于进一步认识Nb₃Sn材料超导性能的弱化机理。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.