高聚物玻璃化转变温度和分子参数的关系 Ⅲ·聚甲基丙烯酸甲酯立构规整性和T_g的关系

本文研究了聚甲基丙烯酸甲酯(PMAA)的立构规整性与T_8的关系,结果表明立构单元分布和含量均对T_8有显著影响。应用前文导出的理论关系,进一步处理了T_8和构象参数实验数据,用这种简单方法计算得的无扰尺寸温度系数和实验值一致。由此推论,不同立构PMMA链的T_8之差反映了它们局部择优链构象的不同。     

结晶性间同立构1,2-聚丁二烯的单晶结构

近十几年来 ,结晶性间同立构 1 ,2 -聚丁二烯引起人们的广泛关注 ,但绝大多数研究工作集中在聚合物的制备、物理性质和应用方面[1～ 3] ,对于其结晶行为和晶体结构则未见报道 .原因是间同立构 1 ,2 -聚丁二烯分子侧链含有大量的双键 ,在较高温度下很容易交联 ,特别是高间规度的聚合物 ,由于其熔融温度高 (>2 0 0℃ )则更易产生交联 ,这给结晶行为和结构研究带来很大困难 .结晶性间同立构 1 ,2 -聚丁二烯的晶体结构为平面锯齿链正交堆砌 ,Pacm空间群[4 ] .我们曾报道了结晶性间同立构 1 ,2 -聚丁二烯的合成和溶液浇铸膜的板条状结构[5] ,本…     

甲基丙烯酸甲酯原子转移自由基聚合等规度研究

在0～100℃温度范围内,由原子转移自由基聚合方法,采用助催化和非助催化体系,引发甲基丙烯酸甲酯聚合,利用¹³CNMR测定聚甲基丙烯酸甲酯的等规度.发现原子转移自由基聚合仍以间同立构为主,随着聚合温度的升高间同立构等规度降低,与通常自由基聚合对有规立构控制特征相似.助催化剂异丙醇铝和活性端羰基配位,对聚合物的立构规整性有一定的影响.     

自成核对间同立构1,2-聚丁二烯结晶行为的影响

间同立构 1 ,2 -聚丁二烯自 1 95 5年问世以来 ,引起人们的广泛关注 ,但其形态结构方面的研究却很少报道 [1] .原因是间同立构 1 ,2 -聚丁二烯分子侧链含有大量双键 ,在较高温度下 ( >1 5 0℃ )很容易产生热交联 ,严重影响该聚合物的结晶行为 .我们曾报道了结晶性间同立构 1 ,2 -聚丁二烯的合成和溶液浇铸膜的板条状结构以及单晶结构 [2 ,3] .本文研究了间同立构 1 ,2 -聚丁二烯的自成核过程、结晶行为和形态结构 .自成核 ( Self- seeding nu-cleation)是指聚合物自身的微小晶粒作为晶核而诱导结晶生长的一种成核方式 ,它具有很高的成核效…     

高聚物玻璃化转变温度和分子参数的关系 Ⅲ·聚甲基丙烯酸甲酯立构规整性和Tg的关系

 本文研究了聚甲基丙烯酸甲酯(PMAA)的立构规整性与T₈的关系,结果表明立构单元分布和含量均对T₈有显著影响。应用前文导出的理论关系,进一步处理了T₈和构象参数实验数据,用这种简单方法计算得的无扰尺寸温度系数和实验值一致。由此推论,不同立构PMMA链的T₈之差反映了它们局部择优链构象的不同。     

间同立构1,2-聚丁二烯的合成和形态结构研究

间同立构 1 ,2 -聚丁二烯自 1 955年问世以来 ,引起人们的广泛关注 ,但绝大多数研究工作集中在聚合物的合成方面[1～ 3] ,对其形态结构方面的研究却很少报道[4 ] ,原因是该聚合物分子侧链含有大量双链 ,在较高温度下 (>1 50℃ )很容易产生热交联 ,这给结构研究造成了很大困难 .间同立构 1 ,2 -聚丁二烯的性能取决于间规度 ,低间规度聚合物呈现弹性体特征 ,而高间规度聚合物则是一种半结晶性塑料 ,其结晶为平面锯齿链正交堆砌 ,Pacm空间群[4 ] .本文采用一种新的催化体系 ,使合成的 1 ,2 -聚丁二烯间规度可以调控 .同时首次报道了结晶性间规…     

磁场对聚合物立体构型影响的研究(Ⅰ)——聚甲基丙烯酸甲酯

本文研究了在甲基丙烯酸甲酯聚合过程中,磁场对产物中间同立构含量的影响。间同立构含量的测定是采用红外光谱定量法。实验结果表明: (1)聚甲基丙烯酸甲酯的间同立构百分含量S%值随磁场强度的增加按指数关系增加。 (2)聚甲基丙烯酸甲酯的玻璃化温度随磁场强度的增加而增加。 (3)聚甲基丙烯酸甲酯的平均分子量随磁场强度的增加,也按指数关系增加。 (4)通过公式计算了聚甲基丙烯酸甲酯分子链中能连续出现N个间同立构链节的组成几率F_N值。     

聚(1,4-环己二烯碳酸酯)立体低聚物的合成及微结构分析

聚合物微结构控制是配位催化聚合领域最重要的目标之一.而合成各种立构规整性低聚物及其核磁碳谱研究是聚合物微结构定性和定量分析的关键.本文以手性环己-4-烯-1,2-二醇为原料,采用N,N'-羰基二咪唑和三光气作为羰化试剂,设计合成了CO_2/1,2-环氧-4-环己烯交替共聚物(聚(1,4-环己二烯碳酸酯),PCEC)全同立构和间同立构的二聚体、四聚体、六聚体、八聚体和十二聚体模型化合物.通过分析全同立构和间同立构模型化合物的核磁碳谱,完成了PCEC微结构的碳谱信息归属.发现聚合物全同立构序列的羰基、次甲基和亚甲基区域的出峰位置分别在δ=154.04、73.83和29.91;间同立构序列的羰基、次甲基和亚甲基区域的出峰位置分别在δ=153.72、72.97和28.98.     

铁系催化剂上合成高乙烯基聚丁二烯的研究Ⅰ.三苯基磷酸酯的影响

 考察了不同磷化合物、催化剂组成、加料方式及反应温度对2-乙基己酸铁(Fe)-三异丁基铝(Al)催化剂上1,3-丁二烯(BD)聚合反应的影响,发现以三苯基磷酸酯(P)为配体的铁系催化剂在己烷中,n(Fe)∶n(P)∶n(Al)=1∶4∶25,加料方式为BD+Fe+P+Al和θ=50 ℃的条件下具有最高的催化活性,聚合产物的分子量分布指数为250,GPC淋出曲线呈单峰分布,表明该催化剂具有单一的活性中心. 经NMR,GPC,DSC和XRD测定,所得聚丁二烯具有较高的1,2-结构含量(95%),较高的间同立构规整度(95%),较高的结晶度(68%),较高的分子量(Mn=74×105)及较高的熔点(189 ℃). 反应条件对聚合产物的立构规整性无明显影响.     

新型铁系催化剂聚合丁二烯

以铁化合物Fe(CF3SO3)2为催化剂,烷基铝为助催化剂,亚磷酸二异辛脂(P8)为给电子体,研究了该催化体系对丁二烯的聚合行为。 结果表明, 催化体系（n(Fe)∶n(P8)∶n(Al)=1∶4∶20）具有良好的聚合活性和间同立构选择性,并且聚合活性和间同立构选择性随聚合温度升高而增加,50 ℃时可得到1,2-结构含量大于85%、间规度达99%以上的间同1,2-聚丁二烯;该催化体系具有很好的立体选择性和温度耐受性,克服了以往铁系催化体系立体选择性差、需要低温聚合的缺点,并且催化体系不涉及使用有毒、有害的催化剂组分。     

Fluorescence probe studies on the complexation between poly(methacrylic acid) and poly(N, N-diethylacrylamide)

The complexation between poly(methacrylic acid) (PMAA) and poly(N, N-diethylacrylamide) (PDEAM) in aqueous phase was studied by UV-vis and fluorescence probe techniques. It was demonstrated that the complexation of PMAA with PDEAM occurs within a pH range of 1-6.5 and along with the complexation, the conformation of PMAA changed from a hypercoiled to a loose coiled form. The complex ratio between the two polymers is 1:1 (PMAA:PDEAM, in monomer unit). Salt effect studies showed that the complexation occurred due to formation of hydrogen bonds between the two polymers. Based upon these conclusions and the "compact micelle-like structure" for PMAA at low pH, a "ladder" model was proposed for the structure of PMAA-PDEAM complex formed at low pH.     

磁性半互穿网络智能水凝胶的合成及性质评价

以甲基丙烯酸(MAA)、N-异丙基丙烯酰胺(NIPAAm)、丙烯酰胺(AM)为原料,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,利用IPN技术并结合磁性的γ-Fe2O3增强剂,在水溶液中制备了半互穿网络水凝胶(PMAA/PAM-NIPAAm/γ-Fe2O3),研究了水凝胶的溶胀性﹑热稳定性和电磁性。实验表明,水凝胶形成稳定的IPN互穿网络结构且该水凝胶具温度、pH双重敏感性和顺电磁性。所合成的水凝胶在低临界溶解温度31℃以下,具有明显正向温敏性,高于此温度,水凝胶的温度敏感性会逐渐减弱。产品成功克服了NIPAAm类水凝胶的温缩性。     

Thermal stability of porous it‐PMMA thin film obtained by the extraction of st‐PMAA from it‐PMMA/st‐PMAA stereocomplex with layer‐by‐layer assembly on a substrate

The functionality of porous isotactic (it) poly(methyl methacrylate) (PMMA) thin films, which were previously developed by the selective extraction of syndiotactic (st) poly(methacrylic acid) (PMAA) from the it‐PMMA/st‐PMAA stereocomplex thin film on a substrate using the layer‐by‐layer assembly method was investigated after thermal treatment (70, 80, and 90 °C) in water for 4 h. Quartz crystal microbalance analysis and infrared spectra measurements revealed that the st‐PMAA incorporation ability of the porous it‐PMMA thin film decreased in order at 80 and 90 °C, while there was no decrease observed at 70 °C. X‐ray diffraction analysis also supported the thermal stability of the porosity at 70 °C, whereas two it‐PMMA crystalline peaks (2θ = 9° and 14°) were generated during heating at 90 °C. The loss of the functionality of the it‐PMMA thin film was thus shown to be due to crystallization, which was caused by the increase in polymer‐chain mobility during the heating process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3265–3270, 2010     

Self-association of water-soluble fluorinated diblock copolymers in solutions

The self-association of the fluorinated diblock copolymer, poly(methacrylic acid)-block-poly(perfluorooctylethyl methacrylate) (PMAA-b-PFMA), in water has been investigated by light scattering, potentiometry, atomic force microscopy, and transmission electron microscopy. The size of the polymer micelles increases, as the degree of dissociation of the PMAA blocks increases. Since the charged PMAA block takes the stretched structure, PMAA-b-PFMA can easily form large micelles due to the low steric hindrance of PMAA blocks. Addition of NaCl shielded electrostatic repulsion in the PMAA chain and induced the formation of smaller micelles than water without NaCl did because of the bulky structure of the PMAA chain in the shell of the micelles. The micelle of PMAA-b-PFMA in ethanol is larger than that of poly(t-butyl methacrylate)-block-poly(perfluorooctylethyl methacrylate) (PtBMA-b-PFMA) in ethanol as a result of the higher steric hindrance of the PtBMA block. The dimensions of the core and shell of the micelles were estimated. The micelle of PMAA-b-PFMA in water possesses a rather thick shell and a large volume per molecule, consistent with the extended PMAA chain. On the other hand, the shell of the micelle in an ethanol solution of PtBMA-b-PFMA is thin but has a large surface area. Facts are consistent with the shrunk structure of the PtBMA block in poor solvent.     

Synthesis of cyclic methacrylic acid oligomers by atom transfer radical polymerization

Poly(methacrylic acid) (PMAA) oligomers were synthesized by combining template polymerization and copper‐mediated atom transfer polymerization with multivinyl monomer of β‐cyclodextrin (CD) having 20.4 methacryloyl groups on both primary and secondary hydroxyl group sides of CD scaffold, with 1,3‐dibromobutane as an initiator. The initiation and propagation sites of polymerized sequence of β‐CD were connected by postpolymerization of polymerized products with CuBr and tris[(2‐dimethylamino)ethyl]amine (Me₆TREN) in a methanol/water mixture of 10 wt % of water. Polymerized and cyclized sequences, PMAA oligomers formed on the primary and the secondary hydroxyl group sides, were detached from β‐CD scaffold by hydrolysis. Molecular weights of PMAA oligomers were measured by GPC and matrix assisted laser desorption ionization time‐of‐flight mass measurement. By ¹H NMR measurements, it was found that three types of cyclic PMAA were obtained by postpolymerization. The cyclization preferentially occurred on the secondary hydroxyl group side than on the primary hydroxyl group side. From the structures of cyclic PMAA, two reaction positions were proposed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6262–6271, 2005     

Studies on interpolymer self-organisation behaviour of protoporphyrin IX bound poly(carboxylic acid)s with complimentary polymers by means of fluorescence techniques

Covalently bound protoporphyrin IX was used as a fluorophore to investigate the interpolymer complex formation between the poly(carboxylic acid)s, PMAA/PAA and poly(N-vinyl pyrrolidone), PVP, poly(ethylene oxide), PEO or poly(ethylene glycol), PEG. Absorption and emission spectral properties of protoporphyrin IX bound to PAA, PMAA and PVP have been studied. Protoporphyrin IX in poly(MAA-co-PPIX) was found to be present in the dimer or higher aggregated form at low pH due to the environmental restriction imposed by the polymer whereas in the case of poly(AA-co-PPIX) and poly(VP-co-PPIX), PPIX exists in monomeric form. The fluorescence intensity and lifetime of PPIX bound to poly(carboxylic acid)s increase on complexation through hydrogen bonding with PVP, PEO and PEG due to the displacement of water molecules in the vicinity of the PPIX. Poly(MAA-co-PPIX) shows longer fluorescence lifetime due to the more compact interpolymer complexation as compared to poly(AA-co-PPIX) due to the enhanced hydrophobicity of PMAA. Poly(VP-co-PPIX) shows a decrease in the fluorescence lifetime on complexation with PMAA or PAA due to the hydrophilic and microgel like environment of the fluorophore bound to PVP. The contrasting behaviour of the same polymer adduct with respect to the site of the fluorophore is interpreted to be due to the solvent structure which determines the environment of the fluorophore.     

Tandem mass spectrometry of poly(methacrylic acid) oligomers produced by negative mode electrospray ionization

Dissociation of small poly(methyl acrylic acid) (PMAA) anions produced by electrospray was characterized by tandem mass spectrometry. Upon collisional activation, singly, and doubly deprotonated PMAA oligomers were shown to fragment via two major reactions, dehydration and decarboxylation. The elimination of a water molecule would occur between two consecutive acid groups in a charged-remote mechanism, giving rise to cyclic anhydrides, and was shown to proceed as many times as pairs of neutral pendant groups were available. As a result, the number of dehydration steps, together with the abundance of the fragment ions produced after the release of all water molecules, revealed the polymerization degree of the molecule in the particular case of doubly charged oligomers. For singly deprotonated molecules, the exact number of MAA units could be reached from the number of carbon dioxide molecules successively eliminated from the fully dehydrated precursor ions. In contrast to dehydration, decarboxylation reactions would proceed via a charge-induced mechanism. The proposed dissociation mechanisms are consistent with results commonly reported in thermal degradation studies of poly(acrylic acid) resins and were supported by accurate mass measurements. These fragmentation rules were successfully applied to characterize a polymeric impurity detected in the tested PMAA sample.     

Effect of thickness on the thermal properties of hydrogen-bonded LbL assemblies

Layer-by-layer (LbL) assemblies have attracted much attention for their functional versatility and ease of fabrication. However, characterizing their thermal properties in relation to the film thickness has remained a challenging topic. We have investigated the role of film thickness on the glass transition temperature (T(g)) and coeffecient of thermal expansion for poly(ethylene oxide)/poly(acrylic acid) (PEO/PAA) and PEO/poly(methacrylic acid) (PEO/PMAA) hydrogen-bonded LbL assemblies in both bulk and ultrathin films using modulated differential scanning calorimetry (modulated DSC) and temperature-controlled ellipsometry. In PEO/PAA LbL films, a single, well-defined T(g) was observed regardless of film thickness. The T(g) increased by 9 °C relative to the bulk T(g) as film thickness decreased to 30 nm because of interactions between the film and its substrate. In contrast, PEO/PMAA LbL films show a single glass transition only after a thermal cross-linking step, which results in anhydride bonds between PMAA groups. The T(g), within error, was unaffected by film thickness, but PEO/PMAA LbL films of thicknesses below ~2.7 μm exhibited a small amount of PEO crystallization and phase separation for the thermally cross-linked films. The coefficients of thermal expansion of both types of film increased with decreasing film thickness.     

预氧化聚铝碳硅烷纤维的热分解动力学及其机理

利用热重分析仪(TGA)对预氧化聚铝碳硅烷(PACS)纤维进行了热动力学研究, 用改良的Coats-Redfern法计算了动力学参数, 用Doyle法计算了理论失重值, 并根据FT-IR, XRD和SEM对其热分解的机理进行了分析. 结果表明, 在热分解反应的主要阶段, 预氧化纤维的反应活化能低于PACS纤维, 氧的引入有利于纤维的热分解; 快速升温有利于预氧化PACS纤维的热分解. 在初始分解阶段, 主要为低分子量的PACS和H₂O的逸出, 同时≡Si—H键之间以及≡Si—H与≡Si—CH₃键发生了脱氢、脱CH₄反应, 从而导致交联程度的增加; 随热分解温度进一步的提高, 分子的有机侧基急剧热解, 分解产物从有机物转变为存在部分微晶的无机结构; 热分解温度继续提高, 纤维结构进一步完善, 1300 ℃左右, β-SiC晶粒大小约为2～4 nm左右, 纤维具有较好的性能.     

Nanoaggregates of ABC-type triple hydrophilic block copolymers by binding of cationic surfactant

A triple hydrophilic block copolymer comprised of poly(ethylene oxide), poly(sodium 2-acrylamido-2-methylpropanesulfonate), and poly(methacrylic acid) (PEO–PAMPS–PMAA) does not form a micelle by itself when it is dissolved in water. However, in the previous paper, we fabricated the nanoaggregates of PEO–PAMPS–PMAA and cationic surfactant, such as cetyltrimethylammonium chloride (CTAC), by insolubilizing the anionic PAMPS and/or PMAA blocks of the polymer with CTAC only at high pH. In this paper, we fabricated the nanoaggregates of dodecyltrimethylammonium chloride (DTAC) and PEO–PAMPS–PMAA in a wide range of pH to examine the effect of ionization of the PMAA blocks of the polymer on the aggregates formation of PEO–PAMPS–PMAA. The properties of the nanoaggregates are affected by the ionization of PMAA block of the polymer. DTAC (C12 alkyl chain) was employed instead of CTAC (C16 alkyl chain) to reveal the effect of alkyl chain length of surfactant on the aggregate formation of PEO–PAMPS–PMAA. The properties of PEO–PAMPS–PMAA nanoaggregates also depend on the structure of surfactant. The binding of DTAC to PEO–PAMPS–PMAA was monitored by electrophoresis measurements, while the formation of DTAC/PEO–PAMPS–PMAA nanoaggregates was confirmed by scanning electron microscopy, dynamic light scattering measurements and fluorescence spectroscopy.