Oxidaiton of tin/II/ in air-kept hydrochloric acid solutions

An air-storage stability of tin/II/ chloride solution was studied by voltammetric and spectrophotometric methods. The chosen concentration range was due to the problems of the kits preparation for a^99mTc generator. The rate of oxidation of tin/II/ in the range of 0.04–12.5 mg.ml^–1 was shown to decrease with an increase in tin concentration. According to the obtained results one can determine maximal storage time for the correct practical use.     

Catalytic oxidation of no to NO2 over Cr/TiO2 and Cu/TiO2 under oxidizing atmosphere

The catalytic activity of Cr/TiO₂ and Cu/TiO₂ for the oxidation of NO under an oxidizing atmosphere has been examined. Both catalysts had excellent ability for the oxidation of NO to NO₂ in the temperature range of 350–400°C.     

Oxidation process of MoOxCy to MoO3: kinetics and mechanism

A non-isothermal kinetic study of the oxidation of “carbon-modified MoO₃” in the temperature range of 150-550°C by simultaneous TGA-DTA was investigated. During the oxidation process, two thermal events were detected, which are associated with the oxidation of carbon in MoO_xC_y and MoO₂ to MoO₃. The model-free and model-fitting kinetic approaches have been applied to TGA experimental data. The solid state-kinetics of the oxidation of MoO_xC_y to MoO₃ is governed by F1 (unimolecular decay), which suggests that the reaction is of the first order with respect to oxygen concentration. The constant (Ea)_α value (about 115±5 kJ/mol) for this first stage can be related to the nature of the reaction site in the MoO₃ matrix. This indicates that oxidation occurs in well-defined lattice position sites (energetically equivalent). On the other hand, for the second stage of oxidation, MoO₂ to MoO₃, the isoconversional analysis shows a complex (Ea)_α dependence on (α) and reveals a typical behavior for competitive reaction. A D2 (two-dimensional diffusion) mechanism with a variable activation energy value in the range 110-200 kJ/mol was obtained. This can be interpreted as an inter-layer oxygen diffusion in the solid bulk, which does not exclude other simultaneous mechanism reactions.     

金纳米粒子和钼氧化物复合膜修饰电极的制备及应用

利用循环伏安法将金纳米粒子和钼氧化物共同电沉积在玻碳电极表面,制备了金纳米粒子和钼氧化物复合膜修饰电极,利用SEM和XPS研究了MoOx/AuNPs复合膜的表面形态,并研究其修饰电极对葡萄糖的电催化氧化过程. 首次提出了阳极扫描极化反向催化伏安法,即在反向扫描过程中纯的催化氧化电流通过扣减背景电流的方法被提取出来. 显著提高电流测量灵敏度改善了信噪比. 制备的MoOx/AuNPs复合膜修饰电极在0.01-4.0 mmol/L对葡萄糖具有线性响应,电流灵敏度为2.35 mA·L/（mmol·cm2）,检测限为9.01 μmol/L（信噪比为3）.     

A Vinylanthracene and Vinylferrocene‐Containing Copolymer: A New Dual pH/Sulfide Sensor

A single electroactive copolymer containing both anthracene and ferrocene units has been synthesized to form a dual pH/sulfide sensor. Under cyclic voltammetric conditions the oxidation of the ferrocene moiety undergoes an electrocatalytic reaction with sulfide, producing a linear increase in the oxidative peak current over the range 0.2–2.0 mM. Furthermore, square wave voltammetry was utilized to determine the pH of the solution by measuring the variation in the anthracene oxidation potential with respect to the ferrocene oxidation wave.     

Electrochemical determination of methimazole based on the acetylene black/chitosan film electrode and its application to rat serum samples

A novel method has been developed for the determination of methimazole, which was based on the enhanced electrochemical response of methimazole at the acetylene black/chitosan composite film modified glassy carbon electrode. The electrochemical behavior of methimazole was studied at this film electrode by cyclic voltammetry and differential pulse voltammetry. The experimental results showed that methimazole exhibited a remarkable oxidation peak at 0.63V at the film electrode. Compared with the bare glassy carbon electrode, the oxidation peak current increased greatly, and the peak potential shifted negatively, which indicated that the acetylene black/chitosan film electrode had good catalysis to the electrochemical oxidation of methimazole. The enhanced oxidation current of methimazole was indebted to the nano-porus structure of the composite film and the enlarged effective electrode area. The influences of some experimental conditions on the oxidation of methimazole were tested and the calibration plot was examined. The results indicated that the differential pulse response of methimazole was linear with its concentration in the range of 1.0×10(-7) to 2.0×10(-5)mol/L with a linear coefficient of 0.998, and in the range of 4.0×10(-5) to 3.0×10(-4)mol/L with a linear coefficient of 0.993. The detection limit was 2.0×10(-8)mol/L (S/N=3). The film electrode was used to detect the content of methimazole in rat serum samples by the standard addition method with satisfactory results.     

多菌灵在羧甲基纤维素钠/蒙脱土修饰电极上的电化学行为及测定

制备了羧甲基纤维素钠/蒙脱土修饰电极,研究了多菌灵在该修饰电极上的电化学行为并用方波伏安法对其进行测定。实验结果表明,多菌灵在修饰电极上出现了一个不可逆氧化峰,该氧化过程受扩散控制,多菌灵浓度在2.0×10-6～6.0×10-5mol/L范围内,方波伏安法的氧化峰电流与多菌灵浓度呈现良好的线性关系,检出限为8.5×10-7mol/L,可用于检测溶液中多菌灵含量。     

Preparation of photocatalytic nano-ZnO/TiO2 film and application for determination of chemical oxygen demand

A composite nano-ZnO/TiO₂ film as photocatalyst was fabricated with vacuum vaporized and sol-gel methods. The nano-ZnO/TiO₂ film improved the separate efficiency of the charge and extended the range of spectrum, which showed a higher efficiency of photocatalytic than the pure nano-TiO₂ and nano-ZnO film. The photocatalytic mechanism of nano-ZnO/TiO₂ film was discussed, too. A new method for determination of low chemical oxidation demand (COD) value in ground water based on nano-ZnO/TiO₂ film using the photocatalytic oxidation technology was founded. This method was originated from the direct determination of the Mn(VII) concentration change resulting from photocatalytic oxidation of organic compounds on the nano-ZnO/TiO₂ film, and the COD values were calculated from the absorbance of Mn(VII). Under the optimal operation conditions, the detection limit of 0.1 mg l⁻¹, COD values with the linear range of 0.3-10.0 mg l⁻¹ were achieved. The results were in good agreement with those from the conventional COD methods.     

Oxidation behavior of Ru/TiO2 and metallic Ru fine particles on heating in air

Thermogravimetry (TG) and differential thermal analysis (DTA) were used to investigate the oxidation behavior of Ru/TiO2 and metallic Ru fine particles during heating in air in the range 20-1000 degrees C. Temperature ranges of the oxidation for two samples of Ru/TiO2 with the compositions (92 wt% Ru, 8 wt% TiO2) and (75 wt% Ru, 25 wt% TiO2) and for pure metallic Ru fine particle agglomerates were determined. It was assumed that after the partial oxidation of Ru in the sample containing 75 wt% Ru and 25 wt% TiO2 and in the pure metallic Ru a diffusion barrier was formed, preventing further oxidation of Ru in Ru/RuO2 and Ru/RuO2/TiO2 matrices. XRD and TEM were used for the sample characterization.     

吸附有苯酚氧化残留物的Cu-Ce/AC吸附 催化剂的氢处理研究

对经苯酚吸附和干态催化氧化过程后吸附有苯酚残留物的活性炭载氧化铜和氧化铈(Cu Ce/AC)进行了氢处理研究。结果表明,氢处理可明显促进残留物的分解,恢复Cu Ce/AC对苯酚的吸附性能,减少在后续苯酚氧化过程中苯酚脱附量。氢处理温度越高,苯酚吸附容量恢复得越好。但氢处理不能恢复Cu Ce/AC对苯酚的催化氧化活性,是由于活性组分晶粒长大所致。     

Catalytic Oxidation of Dimethyl Ether to Hydrocarbons over SnO2/MgO and SnO2/CaO Catalysts

A novel reverse microemulsion method was used to prepare SnO2/MgO and SnO2/CaO catalysts. It was found that both the catalysts were active for the reaction of catalytic oxidation of dimethyl ether (DME) in the temperature range of 275 to 300℃. SnO2/CaO catalyst exhibits much higher activity than SnO2/MgO. On SnO2/CaO catalyst, DME conversion of 21.8% was obtained at 300℃, while selectivities to methyl formate (MF) and dimethoxyethane (DMET) of 19.1% and 59.0% respectively were obtained at 275℃.     

Electrochemical Detection of Hydrazine Based on Electrospun Palladium Nanoparticle/Carbon Nanofibers

In this work, we developed an electrochemical method for the detection of hydrazine based on palladium nanoparticle/carbon nanofibers (Pd/CNFs). Pd/CNFs were prepared by electrospinning technique and subsequent thermal treatments. The electrocatalytic behaviors of Pd/CNFs modified glassy carbon electrode (Pd/CNF‐GCE) for hydrazine oxidation were evaluated by cyclic voltammetry (CV), an obvious and well‐defined oxidation peak appeared at ?0.32 V (vs. Ag/AgCl). The mechanism of the oxidation of hydrazine at Pd/CNF‐GCE was also studied, which demonstrated an irreversible diffusion‐controlled electrode process and a four‐electron transfer involved in the overall reaction. Furthermore, the wide linear range, low detection limit, good reproducibility and excellent storage stability were obtained utilizing differential pulse voltammetry (DPV).     

Reaction of oxygen with adsorbed hydrogen species of a reduced Pt/TiO2 catalyst

Reaction of oxygen with the adsorbed hydrogen species of Pt/TiO₂ catalysts reduced in the temperature range of RT-773 K has been studied by temperature-programmed oxidation (TPO). It is obtained that the Pt-assisted reaction of oxygen with both the surface hydroxy groups and titanium hydride species occurs in the temperature range of 320–450 K; direct oxidation of the surface hydrogen species takes place on the surface of TiO₂ in the temperature range of 500–600 K; and oxygen reacts with the stored hydrogen species in the sublayer and bulk of the TiO₂ support when the temperature was increased to above 600 K.     

Preferential CO oxidation promoted by the presence of H2 over K-Pt/Al2O3

In preferential CO oxidation in H2-rich gas, K-Pt/Al2O3(K/Pt = 10) was very effective in decreasing CO concentration below 10 ppm in the 375-410 K range, and the turnover frequency of the K-Pt/Al2O3 was 20 times as high as that of Pt/Al2O3 at 353 K; furthermore, the activity of CO oxidation was promoted drastically by the presence of H2.     

In situ surface oxidation study of a planar Co/SiO2/Si(100) model catalyst with nanosized cobalt crystallites under model Fischer-Tropsch synthesis conditions

The oxidation of nanosized metallic cobalt to cobalt oxide during Fischer-Tropsch synthesis (FTS) has long been postulated as a major deactivation mechanism. In this study a planar Co/SiO(2)/Si(100) model catalyst with well-defined cobalt crystallites, close to the threshold value reported for oxidation in the literature (4-10 nm), was prepared by the spin coating method. The planar Co/SiO(2)/Si(100) model catalyst was characterized with atomic force microscopy, X-ray photoelectron spectroscopy, and Rutherford backscattering. The surface oxidation behavior of the nanosized metallic cobalt crystallites of 4-5 nm was studied using in situ near-edge X-ray absorption fine structure under model FTS conditions, i.e., H(2)/H(2)O = 1, P(Total) = 0.4 mbar, and 150-450 degrees C. No surface oxidation of metallic cobalt was observed under these model FTS conditions over a wide temperature range, i.e., 150-400 degrees C.     

Partial oxidation of dimethyl ether to H2/syngas over supported Pt catalyst

Dimethyl ether （DME） is a non-toxic fuel with high H/C ratio and high volumetric energy density, and could be served as an ideal source of H2/syngas production for application in solid oxide fuel cells （SOFC）. This study presents results of DME partial oxidation over a 1.5 wt% Pt/Ce0.4Zr0.6O2 catalyst under the condition of gas hourly space velocity （GHSV） of 15000-60000 ml/（g·h）, molar ratio of O2/DME of 0.5 and 500-700 ℃, and this temperature range was also the operation temperature range for intermediate temperature SOFC. The results indicated that the catalyst showed good activity for the selective partial oxidation of DME to H2/syngas. Under the working conditions investigated, DME was completely converted. Increase in reaction temperature enhanced the amount of syngas, but lowered the H2/CO ratio and yield of methane; while increase in reaction GHSV resulted in only slight variation in the distribution of products. The good catalytic activity of Pt supported on Ce0.4Zr0.6O2 for the partial oxidation of DME may be directly associated with the good oxygen storage capacity of the support, which is worth of further investigation to develop materials for application in SOFC.     

O2对燃煤烟气中As2 O3均相反应生成途径影响研究

应用量子化学密度泛函理论研究了燃煤烟气中As和AsO与O_2均相生成As_2O_3的反应机理。首先计算确定了各反应物、中间体、过渡态和产物的结构和能量,然后运用热力学和动力学方法对As_2O_3均相生成过程进行分析。结果表明,由As和AsO与O_2均相生成As_2O_3的最大反应能垒分别为32.9和157.2kJ/mol,在烟气中由As转化为As_2O_3更为容易进行。在500-1900 K下,各反应的正逆反应速率常数均随温度的提高而增大,但不同反应过程受温度影响的程度不同。As与O_2反应生成AsO和AsO_2的两个反应过程的平衡常数在所研究的温度范围内均大于10~5,能完全反应,可以认为是单向反应。AsO与O_2反应生成AsO_2的过程平衡常数在所研究的温度范围内小于10~5,反应不完全,转化率低。AsO与AsO_2生成As_2O_3(D3H)构型的平衡常数极低,反应难以进行,而生成As_2O_3(GAUCHE)构型反应能垒低,可自发进行。     

抗坏血酸和尿酸在甘氨酸-壳聚糖修饰玻碳电极上的电化学行为及测定

制备了甘氨酸-壳聚糖复合膜修饰玻碳电极(Gly-CTS/GCE),研究了抗坏血酸(AA)和尿酸(UA)在该修饰电极上的电化学行为。结果表明在pH=5.59的磷酸盐缓冲溶液中,AA、UA在Gly-CTS/GCE上均产生灵敏的不可逆氧化峰,其峰电流与浓度在一定范围内呈良好的线性关系。对AA和UA混合溶液平行测定7次,相对标准偏差分别为4.6%、2.9%,表明该电极重现性和稳定性良好。AA、UA在Gly-CTS/GCE电极上的氧化峰峰电位相差340mV,据此可实现对二者的同时检测,并可应用于实际样品测定。     

4‐OH‐TEMPO/TCQ/TBN/HCl: A Metal‐Free Catalytic System for Aerobic Oxidation of Alcohols under Mild Conditions

A green and economical catalyst system, 4‐OH‐TEMPO/TCQ/TBN/HCl, for the aerobic oxidation of a broad range of primary and secondary alcohols to the corresponding carbonyl compounds has been developed. These reactions proceed without transition‐metals under mild conditions with excellent yields.     

Enhanced NADH Oxidation Using Polytyramine/Carbon Nanotube Modified Electrodes for Ethanol Biosensing

Polytyramine (PT) has been electro‐deposited onto multi‐walled carbon nanotube (MWCNT) modified glassy carbon (GC) electrodes via oxidation of tyramine in 0.1 M H₃PO₄ by cycling the potential over the range of −400 mV to 1300 mV (versus Ag/AgCl). The reactivity of the resulting chemically‐modified electrodes was characterized using cyclic voltammetry in the presence and absence of reduced nicotinamide adenine dinucleotide (NADH). The modified electrodes displayed electrochemical activity due to the formation of quinone species and were catalytically active towards NADH oxidation by lowering the oxidation peak potential by 170 mV compared to the value of the MWCNT modified electrode with a peak potential of 180±10 mV (versus Ag/AgCl). The MWCNT/PT surface was further characterized using SEM and XPS methods, which indicated that a thin polymeric film had been formed on the electrode surface. The present work demonstrates the advantage of using PT as a platform that combines both the immobilization of alcohol dehydrogenase (ADH) and the mediation of NADH oxidation at a low overpotential essential to the design of high performance ethanol biosensors, all within an easily electropolymerizable film. The resulting biosensor displayed an ethanol sensitivity of 4.28±0.06 μA mM⁻¹ cm⁻², a linear range between 0.1 mM and 0.5 mM and a detection limit of 10 μM.