Non-Newtonian flow in microporous structures under the electroviscous effect

Single phase non-Newtonian microporous flow combined with the electroviscous effect is investigated in the pore-scale under conditions of various rheological properties and electrokinetic parameters. The lattice Boltzmann method is employed to solve both the electric potential field and flow velocity field. The simulation of commonly used power-law non-Newtonian flow shows that the electroviscous effect on the flow depends on both the fluid rheological behavior and pore surface area ratio significantly. For the shear thinning fluid with power-law exponent n < 1, the fluid viscosity near the wall is smaller and the electrovicous effect plays a more important role compared to the Newtonian fluid and shear thickening fluid. The high pore surface area ratio in the porous structure increases the electroviscous force and the induced flow resistance becomes important even to the flow of Newtonian and shear thickening fluids.     

Soret and Dufour effect on double diffusion mixed convection from a vertical surface in a porous medium saturated with a non-Newtonian fluid

A non-similar boundary layer analysis is presented to study the flow, heat and mass transfer characteristics of non-Darcian mixed convection of a non-Newtonian fluid from a vertical isothermal plate embedded in a homogeneous porous medium with the effect of Soret and Dufour and in the presence of either surface injection or suction. The value of the mixed-convection parameter lies between 0 and 1. In addition, the power-law model is used for non-Newtonian fluids with exponent n < 1 for pseudoplastics n = 1 for Newtonian fluids and n > 1 for dilatant fluids. Furthermore, the coordinates and dependent variables are transformed to yield computationally efficient numerical solutions that are valid over the entire range of mixed convection, from the pure forced-convection limit to the pure free-convection limit, and the whole domain of non-Newtonian fluids, from pseudoplastics to dilatant fluids. The numerical solution of the problem is derived using a Runge–Kutta integration scheme with Newton–Raphson shooting technique. Distributions for velocity, temperature and concentration, as well as for the rate of wall heat and mass transfer, have been obtained and discussed for various physical parametric values.     

Instability of channel flow of a shear-thinning White–Metzner fluid

We consider the inertialess planar channel flow of a White–Metzner (WM) fluid having a power-law viscosity with exponent n. The case n = 1 corresponds to an upper-convected Maxwell (UCM) fluid. We explore the linear stability of such a flow to perturbations of wavelength k⁻¹. We find numerically that if n < n_c ≈ 0.3 there is an instability to disturbances having wavelength comparable with the channel width. For n close to n_c, this is the only unstable disturbance. For even smaller n, several unstable modes appear, and very short waves become unstable and have the largest growth rate. If n exceeds n_c, all disturbances are linearly stable. We consider asymptotically both the long-wave limit which is stable for all n, and the short-wave limit for which waves grow or decay at a finite rate independent of k for each n.The mechanism of this elastic shear-thinning instability is discussed.     

Impact of aspect ratio on flow boiling of water in rectangular microchannels

In this paper we focus on the impact of varying the aspect ratio of rectangular microchannels, on the overall pressure drop involving water boiling. An integrated system comprising micro-heaters, sensors and microchannels has been realized on (1 1 0) silicon wafers, following CMOS compatible process steps. Rectangular microchannels were fabricated with varying aspect ratios (width [W] to depth [H]) but constant hydraulic diameter of 142 ± 2 μm and length of 20 mm. The invariant nature of the hydraulic diameter is confirmed through two independent means: physical measurements using profilometer and by measuring the pressure drop in single-phase fluid flow. The experimental results show that the pressure drop for two-phase flow in rectangular microchannels experiences minima at an aspect ratio of about 1.6. The minimum is possibly due to opposing trends of frictional and acceleration pressure drops, with respect to aspect ratio. In a certain heat flux and mass flux range, it is observed that the two-phase pressure drop is lower than the corresponding single-phase value. This is the first study to investigate the effect of aspect ratio in two-phase flow in microchannels, to the best of our knowledge. The results are in qualitative agreement with annular flow model predictions. These results improve the possibility of designing effective heat-sinks based on two-phase fluid flow in microchannels.     

Criteria for the appearance of recirculating and non-stationary regimes behind a cylinder in a viscoplastic fluid

The appearance of a recirculation zone and the formation of non-stationary vortices behind a cylinder in the unconfined flow of a Herschel–Bulkley fluid have been studied by numerical simulation. The Herschel–Bulkley constitutive equation was regularised by using the Papanastasiou model. Special attention was paid to determining the numerical parameters and comparing them to existing results. The influence of the Oldroyd number and power-law index on flow morphology and, in particular, on the unyielded zones was studied over a wide spectrum (0 ≤ Od ≤ 10) and (0.3 ≤ n ≤ 1.8). It was seen that the greater the Oldroyd number, the greater the critical Reynolds numbers and Strouhal number for the two flow regimes. The influence of the power-law index is more complex.     

New contributions on laminar flow of inelastic non-Newtonian fluid in the two-dimensional symmetric expansion: Creeping and slowly moving flow conditions

The steady flow of generalized Newtonian fluid in a two-dimensional 1:3 sudden expansion was studied numerically. Finite volume method was applied to solve the momentum equations along with the continuity equation and the Power law rheological model within the laminar flow regime for a range of Reynolds number and Power law index values. The values of generalized Reynolds number, based on physical and rheological properties, upstream channel height and bulk velocity, were varied between 0.0001 ≤ Re_gen ≤ 10, while the Power law index values mapped the 0.60 ≤ n ≤ 1.40 range, allowing for the investigation of both shear-thinning and shear-thickening effects at creeping as well as slowly moving fluid flow conditions. We report accurate results of a systematic study with a focus on most important characteristics of recirculating fluid flow in the downstream section of sudden expansion geometry. It is shown that for the creeping flow regime there exist finite sized redevelopment length, extra pressure drop (Couette correction) and recirculation zones (also called as Moffatt vortices) that are influenced by the non-Newtonian viscous behaviour.     

Comparative study of forced convection of a power-law fluid in a channel with a built-in square cylinder

A detailed comparison between the lattice Boltzmann method and the finite element method is presented for an incompressible steady laminar flow and heat transfer of a power-law fluid past a square cylinder between two parallel plates. Computations are performed for three different blockage ratios (ratios of the square side length to the channel width) and different values of the power-law index n covering both pseudo-plastic fluids (n < 1) and dilatant fluids (n > 1). The methodology is validated against the exact solution. The local and averaged Nusselt numbers are also presented. The results show that the relatively simple lattice Boltzmann method is a good alternative to the finite element method for analyzing non-Newtonian fluids.     

Laminar flow of power-law fluids past a rotating cylinder

In this work, the continuity and momentum equations have been solved numerically to investigate the flow of power-law fluids over a rotating cylinder. In particular, consideration has been given to the prediction of drag and lift coefficients as functions of the pertinent governing dimensionless parameters, namely, power-law index (1 ≥ n ≥ 0.2), dimensionless rotational velocity (0 ≤ α ≤ 6) and the Reynolds number (0.1 ≤ Re ≤ 40). Over the range of Reynolds number, the flow is known to be steady. Detailed streamline and vorticity contours adjacent to the rotating cylinder and surface pressure profiles provide further insights into the nature of flow. Finally, the paper is concluded by comparing the present numerical results with the scant experimental data on velocity profiles in the vicinity of a rotating cylinder available in the literature. The correspondence is seen to be excellent for Newtonian and inelastic fluids.     

Laminar,transitional and turbulent annular flow of drag-reducing polymer solutions

Mean and rms axial velocity-profile data obtained using laser Doppler anemometry are presented together with pressure-drop data for the flow through a concentric annulus (radius ratio κ = 0.506) of a Newtonian (a glycerine–water mixture) and non-Newtonian fluids—a semi-rigid shear-thinning polymer (a xanthan gum) and a polymer known to exhibit a yield stress (carbopol). A wider range of Reynolds numbers for the transitional flow regime is observed for the more shear-thinning fluids. In marked contrast to the Newtonian fluid, the higher shear stress on the inner wall compared to the outer wall does not lead to earlier transition for the non-Newtonian fluids where more turbulent activity is observed in the outer wall region. The mean axial velocity profiles show a slight shift (～5%) of the location of the maximum velocity towards the outer pipe wall within the transitional regime only for the Newtonian fluid.     

Stable two-layer flows at all Re; visco-plastic lubrication of shear-thinning and viscoelastic fluids

Multi-fluid flows are frequently thought of as being less stable than single phase flows. Consideration of different non-Newtonian models can give rise to different types of hydrodynamic instability. Here we show that with careful choice of fluid rheologies and flow paradigm, one can achieve multi-layer flows that are linearly stable for Re = ∞. The basic methodology consists of two steps. First we eliminate interfacial instabilities by using a yield stress fluid in one fluid layer and ensuring that for the base flow configurations studied we maintain an unyielded plug region at the interface. Secondly we eliminate linear shear instabilities by ensuring a strong enough Couette component in the second fluid layer, imposed via the moving interface. We show that this technique can be applied to both shear-thinning and visco-elastic fluids.     

Experimental quantification of the plastic blunting process for stage II fatigue crack growth in one-phase metallic materials

The plastic blunting process during stage II fatigue crack growth was studied in pure polycrystalline Ni to investigate effects of strain localization and inelastic behavior on the kinematics of crack advance. Correlations were obtained between strain fields ahead of a fatigue crack, crack advance per cycle and crack growth kinetics. Strain fields were quantified using a combination of in situ loading experiments, scanning electron microscopy and digital image correlation for 8 < ΔK < 20 MPa m^1/2 and a fixed load ratio of 0.1. Results indicate that strain localized along a dominant deformation band, which was usually crystallographic and carried mostly pure shear for large loads and was of mixed character for lower loads. Instances of double deformation bands were observed, with bands acting either in a simultaneous or alternating fashion. It was found that the area integral of the opening strain for values larger than a given threshold, an “integrated” strain, had a power-law relationship with ΔK, with the exponent approximately equal to the Paris exponent (m). Therefore, the crack growth rate was proportional to the integrated strain. An analysis based on this correlation and the presence of dominant shear bands indicated that the integrated strain is related to the accumulated displacement in the band. This, in turn, is proportional to the product of the cyclic plastic zone radius and the average shear strain ahead of the tip, which represents a basic length scale for plastic blunting. Assumptions on the load dependence of these quantities, based on their observed spatial variation, allowed estimating $m=2\left(1+\frac{1}{1+n^{\prime }}\right)$, where n′ is the cyclic hardening exponent (0 < n′ < 1). This gives 3 < m < 4, which accounts for about 50% of the observed values of m between 1.5 and 6 for a wide variety of metallic materials.     

Asymptotic crack-tip fields for dynamic crack growth in compressive power-law hardening materials

The effect of material compressibility on the stress and strain fields for a mode-I crack propagating steadily in a power-law hardening material is investigated under plane strain conditions. The plastic deformation of materials is characterized by the J₂ flow theory within the framework of isotropic hardening and infinitesimal displacement gradient. The asymptotic solutions developed by the present authors [Zhu, X.K., Hwang K.C., 2002. Dynamic crack-tip field for tensile cracks propagating in power-law hardening materials. International Journal of Fracture 115, 323–342] for incompressible hardening materials are extended in this work to the compressible hardening materials. The results show that all stresses, strains, and particle velocities in the asymptotic fields are fully continuous and bounded without elastic unloading near the dynamic crack tip. The stress field contains two free parameters σ_eq0 and s₃₃₀ that cannot be determined in the asymptotic analysis, and can be determined from the full-field solutions. For the given values of σ_eq0 and s₃₃₀, all field quantities around the crack tip are determined through numerical integration, and then the effects of the hardening exponent n, the Poisson ratio ν, and the crack growth speed M on the asymptotic fields are studied. The approximate behaviors of the proposed solutions are discussed in the limit of ν → 0.5 or n → ∞.     

Smoothed particle hydrodynamics simulation of non-Newtonian moulding flow

Smoothed particle hydrodynamics (SPH) has been widely applied in simulating fluid flow because of its attractive properties, for example, it is fully Lagrangian and mesh free. However, this method usually uses the explicit method to solve the conservation equations and in this form it is only suitable to momentum dominated flows with low viscosity. In polymer processing, the fluid is non-Newtonian with high viscosity, O(10³) to O(10⁴) Pa-s say, and the pressure is high as O(10⁶) to O(10¹⁰) Pa. The algorithm of the standard SPH is infeasible in this case, because only very small time steps can be used for a stable simulation. We have developed an implicit SPH for non-Newtonian flow, which is completely matrix free, to solve the equation system iteratively and robustly. The artificial pressure is introduced between particles to stabilize the SPH system avoiding the tensile instability. The fluid is compressible under high pressure. Realistic state equations for polymers, such as the Tait and SSY [16] equations are adopted to describe the density/pressure relations. The method is finally applied to the simulation of moulding flow of a modified power law fluid with the zero shear rate viscosity of 1.22 × 10⁴ Pa-s, Reynolds number of 3 × 10^?4 to 6 × 10^?5 and the highest pressure of O(10⁸) to O(10¹⁰) Pa.     

Unsteady gravity-driven slender rivulets of a power-law fluid

Unsteady gravity-driven flow of a thin slender rivulet of a non-Newtonian power-law fluid on a plane inclined at an angle α to the horizontal is considered. Unsteady similarity solutions are obtained for both converging sessile rivulets (when 0 < α < π/2) in the case x < 0 with t < 0, and diverging pendent rivulets (when π/2 < α < π) in the case x > 0 with t > 0, where x denotes a coordinate measured down the plane and t denotes time. Numerical and asymptotic methods are used to show that for each value of the power-law index N there are two physically realisable solutions, with cross-sectional profiles that are ‘single-humped’ and ‘double-humped’, respectively. Each solution predicts that at any time t the rivulet widens or narrows according to |x | ^{(2N+1)/2(N+1)} and thickens or thins according to |x | ^N/(N+1) as it flows down the plane; moreover, at any station x, it widens or narrows according to |t | ^?N/2(N+1) and thickens or thins according to |t | ^?N/(N+1). The length of a truncated rivulet of fixed volume is found to behave according to |t | ^N/(2N+1).     

Squeeze flow of a power-law fluid between non-parallel plates

Squeeze flow in the gap between non-parallel circular plates of radius R is discussed. The test material is assumed to be a power-law fluid, with a no-slip boundary condition at the plates. If the mean separation between the plates is h, and the angle of inclination between the plates is ? ? h/R, the force on the plates is perturbed only at O(?²) and is increased by less than 10% if ? < 0.35h/R. A torque O(?) tends to return the plates to a parallel configuration.     

Effect of gravity on the mechanical properties of lunar regolith tested using a low gravity simulation device

Simulations of the bearing capacity and shear strength of regolith under Earth’s gravity produce different results from those under low gravity. A low-gravity simulation device was developed in this study, and an internal stress model of regolith simulant was established to correct the errors. The model revealed additional force on both shear plane in the shear test and the press plate area in the pressure–sinkage test. The sinkage and shear test results showed that low gravity decreased the deformable index n, frictional modulus k_φ and cohesion c, whereas there were no obvious changes to the cohesive modulus k_c and internal friction angle φ. The sinkage generally increased as the gravity decreased under a consistent normal load larger than 50 N, but when the wheel load was lower than 50 N, the sinkage of the TYII-1 simulant was larger under 1 G than 1/6 G. Gravity had little effect on the shear strength of the regolith. However, the tractive thrust of the TYII-1 simulant was lower under 1/6 G than 1 G. The smaller difference was due to differences in the way the soils responded to changes in the gravity level for the TYII-2 simulant.     

Some exact solutions for rotating flows of a generalized Burgers’ fluid in cylindrical domains

The velocity field and the adequate shear stress corresponding to the flow of a generalized Burgers’ fluid model, between two infinite co-axial cylinders, are determined by means of Laplace and finite Hankel transforms. The motion is due to the inner cylinder that applies a time dependent torsional shear to the fluid. The solutions that have been obtained, presented in series form in terms of usual Bessel functions J₁( ? ), J₂( ? ), Y₁( ? ) and Y₂( ? ), satisfy all imposed initial and boundary conditions. Moreover, the corresponding solutions for Burgers’, Oldroyd-B, Maxwell, second grade, Newtonian fluids and large-time transient solutions for generalized Burgers’ fluid are also obtained as special cases of the present general solutions. The effect of various parameters on large-time and transient solutions of generalized Burgers’ fluid is also discussed. Furthermore, for small values of the material parameters, λ₂ and λ₄ or λ₁, λ₂, λ₃ and λ₄, the general solutions corresponding to generalized Burgers’ fluids are going to those for Oldroyd-B and Newtonian fluids, respectively. Finally, the influence of the pertinent parameters on the fluid motion, as well as a comparison between models, is shown by graphical illustrations.     

A model for tracking inertial particles in a lattice Boltzmann turbulent flow simulation

A computationally inexpensive model for tracking inertial particles through a turbulent flow is presented and applied to the turbulent flow through a square duct having a friction Reynolds number of Re_τ = 300. Prior to introducing particles into the model, the flow is simulated using a lattice Boltzmann computation, which is allowed to evolve until a steady state turbulent flow is achieved. A snapshot of the flow is then stored, and the trajectories of particles are computed through the flow domain under the influence of this static probability field. Although the flow is not computationally evolving during the particle tracking simulation, the local velocity is obtained stochastically from the local probability function, thus allowing the dynamics of the turbulent flow to be resolved from the point of view of the suspended particles. Particle inertia is modeled by using a relaxation parameter based on the particle Stokes number that allows for a particle velocity history to be incorporated during each time step. Wall deposition rates and deposition patterns are obtained and exhibit a high level of agreement with previously obtained DNS computational results and experimental results for a wide range of particle inertia. These results suggest that accurate particle tracking through complex turbulent flows may be feasible given a suitable probability field, such as one obtained from a lattice Boltzmann simulation. This in turn presents a new paradigm for the rapid acquisition of particle transport statistics without the need for concurrent computations of fluid flow evolution.     

Evaluation of subgrid-scale models in large-eddy simulation of flow past a two-dimensional block

Large-eddy simulations of flow past a two-dimensional (2D) block were performed to evaluate four subgrid-scale (SGS) models: (i) the traditional Smagorinsky model, (ii) the Lagrangian dynamic model, (iii) the Lagrangian scale-dependent dynamic model, and (iv) the modulated gradient model. An immersed boundary method was employed to simulate the 2D block boundaries on a uniform Cartesian grid. The sensitivity of the simulation results to grid refinement was investigated by using four different grid resolutions. The velocity streamlines and the vertical profiles of the mean velocities and variances were compared with experimental results. The modulated gradient model shows the best overall agreement with the experimental results among the four SGS models. In particular, the flow recirculation, the reattachment position and the vertical profiles are accurately reproduced with a relative coarse grid resolution of (N_x × N_y × N_z=) 160 × 40 × 160 (n_x × n_z = 13 × 16 covering the block). Besides the modulated gradient model, the Lagrangian scale-dependent dynamic model is also able to give reasonable prediction of the flow statistics with some discrepancies compared with the experimental results. Relatively poor performance by the Lagrangian dynamic model and the Smagorinsky model is observed, with simulated recirculating patterns that differ from the measured ones. Analysis of the turbulence kinetic energy (TKE) budget in this flow shows evidence of a strong production of TKE in the shear layer that forms as the flow is deflected around the block.