Simultaneous separation and determination of Cu(II), Fe(III), and Pb(II) by reversed-phase ion-pair chromatography withN,N,N′, N′-ethylene-diaminetetrakis(methylenephosphonic Acid)

Summary A reversed-phase ion-pair chromatographic (RPIPC) method withN,N,N′, N′-ethylenediaminetetrakis(methylenephosphonic acid) (EDTMP) as coordinating agent has been developed for simultaneous separation and detection of Cu(II), Fe(III), and Pb(II) ions. Response is linearly dependent on amount of sample over the range 9.52–50.8 μg mL⁻¹ for Cu(II), 8.31–41.8 μg mL⁻¹ for Fe(III), and 37.3–51.8 μg mL⁻¹ for Pb(II). The method has been applied successfully to an artificial mixed-ore sample.     

Bromide/bromate speciation by NTI-IDMS and ICP-MS coupled with ion exchange chromatography

 Two different mass spectrometric methods, negative thermal ionization isotope dilution mass spectrometry (NTI-IDMS) and inductively coupled plasma mass spectrometry (ICP-MS), off-line and on-line coupled with anion exchange chromatography, have been developed for simultaneous bromide and bromate determinations in water samples. The detection limits of these methods are in the range of 0.03–0.09 μg/L using a 50 mL sample.The results are independent of the content of other anions, which could be demonstrated by the analyses of six mineral waters containing chloride and sulfate of up to 160 mg/L and 1500 mg/L, respectively. Bromide has been analyzed by the NTI-IDMS method in the range of 10–500 μg/L and bromate in the range of 1–50 μg/L with relative standard deviations of 0.3–1.2% and 0.4–6%. Quantification for the ICP-MS method was carried out by the standard addition technique, which resulted in relative standard deviations of 5.5% for bromide at the 500 μg/L level and of 13% for bromate at the level of about 3 μg/L. These results are compared with those described in the literature for ion chromatographic (IC) and other methods and those obtained in this work by IC using UV detection, which allows high concentrations of chloride in the bromate fraction. The detection limits of this IC method are 6 μg/L for bromide and 30 μg/L for bromate. NTI-IDMS and ICP-MS therefore fit the recommendations of the European Union (detection limit<2.5 μg/L; precision and accuracy better than 25% at the 10 μg/L level) for methods analyzing the carcinogenic bromate much better than IC and other methods applied up to now. As a definitive but time consuming method, NTI-IDMS is preferably applicable as a calibration technique, whereas ICP-MS, with relatively short analysis times, due to on-line coupling with chromatography, can be used as a sensitive and powerful routine method for trace bromide and bromate species in water samples. Received: 5 July 1996/Accepted: 7 August 1996     

Bromide/bromate speciation by NTI-IDMS and ICP-MS coupled with ion exchange chromatography

 Two different mass spectrometric methods, negative thermal ionization isotope dilution mass spectrometry (NTI-IDMS) and inductively coupled plasma mass spectrometry (ICP-MS), off-line and on-line coupled with anion exchange chromatography, have been developed for simultaneous bromide and bromate determinations in water samples. The detection limits of these methods are in the range of 0.03–0.09 μg/L using a 50 mL sample.The results are independent of the content of other anions, which could be demonstrated by the analyses of six mineral waters containing chloride and sulfate of up to 160 mg/L and 1500 mg/L, respectively. Bromide has been analyzed by the NTI-IDMS method in the range of 10–500 μg/L and bromate in the range of 1–50 μg/L with relative standard deviations of 0.3–1.2% and 0.4–6%. Quantification for the ICP-MS method was carried out by the standard addition technique, which resulted in relative standard deviations of 5.5% for bromide at the 500 μg/L level and of 13% for bromate at the level of about 3 μg/L. These results are compared with those described in the literature for ion chromatographic (IC) and other methods and those obtained in this work by IC using UV detection, which allows high concentrations of chloride in the bromate fraction. The detection limits of this IC method are 6 μg/L for bromide and 30 μg/L for bromate. NTI-IDMS and ICP-MS therefore fit the recommendations of the European Union (detection limit<2.5 μg/L; precision and accuracy better than 25% at the 10 μg/L level) for methods analyzing the carcinogenic bromate much better than IC and other methods applied up to now. As a definitive but time consuming method, NTI-IDMS is preferably applicable as a calibration technique, whereas ICP-MS, with relatively short analysis times, due to on-line coupling with chromatography, can be used as a sensitive and powerful routine method for trace bromide and bromate species in water samples. Received: 5 July 1996/Accepted: 7 August 1996     

Determination of EDTA in used fixing solutions by capillary electrophoresis

A capillary electrophoretic method for the determination of EDTA has been developed. EDTA was converted to Ni(II)-EDTA prior to separation, separated from Fe(III)-EDTA, thiosulphate, bromide and polythionates using a fused silica capillary (57 cm × 75 μm I.D.) filled with a borate buffer (50 mmol L^–1; pH 8.5; applied voltage, 30 kV) and detected at 214 nm. The separation time is about 6 min. The detection limit achieved is 2 × 10^–6 mol L^–1 for EDTA. This method was applied for the determination of free EDTA in used fixing solutions. Received: 27 February 1998 / Revised: 28 April 1998 / Accepted: 20 May 1998     

Determination of EDTA in used fixing solutions by capillary electrophoresis

A capillary electrophoretic method for the determination of EDTA has been developed. EDTA was converted to Ni(II)-EDTA prior to separation, separated from Fe(III)-EDTA, thiosulphate, bromide and polythionates using a fused silica capillary (57 cm × 75 μm I.D.) filled with a borate buffer (50 mmol L^–1; pH 8.5; applied voltage, 30 kV) and detected at 214 nm. The separation time is about 6 min. The detection limit achieved is 2 × 10^–6 mol L^–1 for EDTA. This method was applied for the determination of free EDTA in used fixing solutions. Received: 27 February 1998 / Revised: 28 April 1998 / Accepted: 20 May 1998     

Preparation and evaluation of a functionalized polymer-coated silica based sorbent for metal ion separation

A silica based sorbent with an anion complexone polymer coating, [24]ane-N₆ macrocycle, was prepared. The chelation properties of this material were investigated by elemental analysis, infrared spectra and Voige’s method. The polymer-coated silica column (25– 40 μm, 100 × 4.6 mm i.d.) was employed for trace metal analyses. Oxalic acid, malonic acid, succinic acid, citric acid, phthalic acid and acetic acid were used as mobile phases. Their retention characteristics were elucidated. Oxalic acid was found to be the most effective eluent. With a mobile phase consisting of oxalic acid (25 mM) and sodium nitrate (25 mM) at pH 4.2, the separation of copper(II), cadmium(II), cobalt(II) and zinc(II) in sea water could be achieved. The identification of metal ions was performed at 510 nm using 4(2-pyridylazo)resorcinol (1 × 10^–4 M) as post column reagent. The limits of detection were 5 × 10^–7 M, 1 × 10^–5 M, 3 × 10^–5 M and 2 × 10^–6 M for copper(II), cadmium(II), cobalt(II) and zinc(II) based on three times the standard deviation of the response for the lowest concentration (n = 5) in the chromatogram with a sample volume of 50 μL. For evaluation of data reliability, oyster tissue (NIST SRM 1566 a) was studied with the proposed system. Received: 9 February 1998 / Revised: 15 May 1998 / Accepted: 16 June 1998     

Preservation procedures for arsenic speciation in a stream affected by acid mine drainage in southwestern Spain

A preservation study has been performed for arsenic speciation in surface freshwaters affected by acid mine drainage (AMD), a pollution source characterized by low pH and high metallic content. Two sample preservation procedures described in the literature were attempted using opaque glass containers and refrigeration: i) addition of 0.25 mol L⁻¹ EDTA to the samples, which maintained the stability of the arsenic species for 3 h; and ii) in situ sample clean-up with a cationic exchange resin, in order to reduce the metallic load, which resulted in a partial co-adsorption of arsenic onto Fe precipitates. A new proposed method was also tried: sample acidification with 6 mol L⁻¹ HCl followed by in situ clean-up with a cationic exchange resin, which allowed a longer preservation time of at least 48 h. The proposed method was successfully applied to water samples with high arsenic content, taken from the Aguas Agrias Stream (Odiel River Basin, SW Spain), which is severely affected by AMD that originates at the nearby polymetallic sulfide mine of Tharsis. The speciation results obtained by liquid chromatography–hydride generation–atomic fluorescence spectrometry (HPLC-HG-AFS) indicated that during the summer the main arsenic species was As(V) at the hundred μg L⁻¹ level, followed by DMA (dimethyl arsenic) and As(III) below the ten μg L⁻¹ level. In winter, As(V) and As(III) increased at least fivefold, whereas the DMA was not detected.     

Determination of ascorbic acid by use of a flow-through solid phase UV spectrophotometric system

A continuous flow-through solid phase spectrophotometric system was developed for the determination of ascorbic acid based on the measurement of its intrinsic absorbance in the UV region when retained on a 1 mm Sephadex QAE A-25 anion exchanger gel layer which is placed into an appropriate quartz flow-through cell, the absorbance exhibited by this solid phase being monitored at 267 nm. A monochannel manifold was used, the sample (300, 600 or 1000 μL) being injected into the carrier solution (acetate buffer). This solution also elutes the analyte after developing the analytical signal, and regenerates the resin layer which, therefore, remains ready for the next sample. The linear dynamic range and other analytical parameters vary according to the sample volume injected. Three calibration lines were established for 300, 600 and 1000 μL sample volume, which ranged from 1.0 to 20.0, 0.5 to 10.0 and 0.2 to 6.0 μg mL^–1, respectively. The detection limits were 0.04 (300 μL), 0.03 (600 μL) and 0.02 μg mL^–1 (1000 μL), the sampling rates 28, 24 and 21 h^–1, and the RSDs (n = 10) 0.87%, 1.08% and 0.90%, respectively. The amount of ascorbic acid in various samples (pharmaceuticals, sweets and urine) were successfully determined with this method. Received: 28 April 1998 / Revised: 3 June 1998 / Accepted: 30 June 1998     

Determination of ascorbic acid by use of a flow-through solid phase UV spectrophotometric system

A continuous flow-through solid phase spectrophotometric system was developed for the determination of ascorbic acid based on the measurement of its intrinsic absorbance in the UV region when retained on a 1 mm Sephadex QAE A-25 anion exchanger gel layer which is placed into an appropriate quartz flow-through cell, the absorbance exhibited by this solid phase being monitored at 267 nm. A monochannel manifold was used, the sample (300, 600 or 1000 μL) being injected into the carrier solution (acetate buffer). This solution also elutes the analyte after developing the analytical signal, and regenerates the resin layer which, therefore, remains ready for the next sample. The linear dynamic range and other analytical parameters vary according to the sample volume injected. Three calibration lines were established for 300, 600 and 1000 μL sample volume, which ranged from 1.0 to 20.0, 0.5 to 10.0 and 0.2 to 6.0 μg mL^–1, respectively. The detection limits were 0.04 (300 μL), 0.03 (600 μL) and 0.02 μg mL^–1 (1000 μL), the sampling rates 28, 24 and 21 h^–1, and the RSDs (n = 10) 0.87%, 1.08% and 0.90%, respectively. The amount of ascorbic acid in various samples (pharmaceuticals, sweets and urine) were successfully determined with this method. Received: 28 April 1998 / Revised: 3 June 1998 / Accepted: 30 June 1998     

Development of a cloud point extraction and preconcentration method for chromium(III) and total chromium prior to flame atomic absorption spectrometry

A sensitive and selective method has been developed for the determination of chromium in water samples based on using cloud point extraction (CPE) preconcentration and determination by flame atomic absorption spectrometry (FAAS). The method is based on the complexation of Cr(III) ions with Brilliant Cresyl Blue (BCB) in the presence of non-ionic surfactant Triton X-114. Under the optimum conditions, the preconcentration of 50 mL of water sample in the presence of 0.5 g/L Triton X-114 and 1.2 × 10⁻⁵ M BCB permitted the detection of 0.42 μg/L chromium(III). The calibration graph was linear in the range of 1.5–70 μg/L, and the recovery of more than 99% was achieved. The proposed method was used in FAAS determination of Cr(III) in water samples and certified water samples. In addition, the developed CPE-FAAS method was also used for speciation of the inorganic chromium species after reduction of Cr(VI) to Cr(III) using a thiosulphate solution of 120 mg/L in the presence of Hg(II) ion as a stabilizer.     

Determination of oxytetracycline and some impurities in plasma by non-aqueous capillary electrophoresis using solid-phase extraction

Summary The potential of a non-aqueous, capillary electrophoresis (NACE) system for separating oxytetracycline from three of its impurities—tetracycline, 4-epioxytetracycline and 4-epitetracycline—using UV detection has been studied. The running buffer was: 25 mM sodium acetate, 1 mM EDTA, methanesulfonic acid, pH 4, dissolved in MeOH-ACN (50∶50,v/v). The method was also used to determine these compounds in pig plasma. A solid-phase extraction (SPE) procedure as a clean-up step has also developed. For this we tested Sep Pak C₁₈, LiChrolut EN and OASIS cartridges. OASIS cartridges were best. Recoveries were 90–100% for all compounds except EOTC which had a recovery of 74%.     

Effect of additives on the chemical vapour generation of bismuthane by tetrahydroborate(III) derivatization

The effect of mM concentrations of K₃[Fe(CN)₆], Fe(III), Mo(VI), KSCN and KMnO₄ on the generation of BiH₃ by the reaction of 0.2–10 μg ml⁻¹ Bi(III) with 0.2 M tetrahydroborate(III) at 1 M acidity (HCl or HNO₃) was investigated. Chemical vapour generation (CVG) of BiH₃ was investigated by atomic absorption spectrometry using a continuous flow reaction system (CF–CVG–AAS) and different mixing sequences and reagent reaction times. Gas chromatography–mass spectrometry (GC–MS) was employed in batch generation experiments with NaBD₄. In the absence of additives, the formation of Bi⁰ at high concentrations of Bi(III) caused rollover of calibration curves and limited the linear range to less than 1 μg ml⁻¹ Bi(III). In the presence of additives, the formation of Bi⁰ was not observed and the linear range was increased to 5 μg ml⁻¹ of Bi(III) while rollover was completely removed. GC–MS experiments indicated that the presence of additives did not affect the direct transfer of H from boron to bismuth. Experiments with CF–CVG–AAS and different mixing sequences and reagent reaction times suggest that additives act by preventing the formation of Bi⁰ through the formation of reaction intermediates which evolve towards the formation of BiH₃ at elevated Bi(III)/NaBH₄ ratios.      

Flow-injection solid surface lanthanide-sensitized luminescence sensor for determination of <Emphasis Type="Italic">p</Emphasis>-aminobenzoic acid

A single optosensing device based on lanthanide-sensitized luminescence was developed for determination of p-aminobenzoic acid (PABA). The method is based on the formation of a complex between PABA and Tb(III) immobilized on the solid phase (QAE A-25 resin) placed inside the flow cell. NaCl (1 M) was used as carrier solution and HCl (0.05 M) as eluent. The sample solutions of PABA (100 μL) containing Tb(III) and buffered at pH = 6.0 were injected into the carrier stream and the luminescence was measured at λ _ex = 290 nm and λ _em = 546 nm. The method shows a linear range from 0.2 to 6.0 μg mL⁻¹ with an RSD of 1.2% (n = 10) and a sampling frequency of 22 h⁻¹. A remarkable characteristic of the method is its high selectivity which allows it to be satisfactorily applied to the analysis of PABA in pharmaceutical samples without prior treatment. Figure Typical emission bands of Tb(III) in a solid-phase PABA–Tb(III) luminescence spectrum     

The use of Chromazurol S in the presence of a mixture of cationic and non-ionic surfactants for the spectrophotometric determination of iron in cereals

Simple and sensitive methods for the spectrophotometric determination of iron(III) in food, based on the formation of coloured complexes of Fe(III) with Chromazurol S (CAS) in the presence of tetradecyltrimethylammonium bromide (TTA) or octadecyltrimethylammonium chloride (ODTA) and Triton X-100 (TX100), have been developed. Optimum pH and the concentrations of CAS, TTA, ODTA, and TX100 ensuring maximum absorbance have been determined. For the Fe-CAS-TTA-TX100 system the molar absorptivity is 1.12 × 10⁵ L/(mol cm) at 650 nm; for Fe-CAS-ODTA-TX100 it is 1.35 × 10⁵ L/(mol cm) at 659.5 nm. Beer’s law was obeyed for iron concentration in the range 0.08–0.56 μg/mL for the complex Fe-CAS-TTA-TX100 and 0.08–0.64 μg/mL for Fe-CAS-ODTA-TX100. The influence of several interfering ions has been discussed. The stoichiometry of the complexes was established by applying Job’s method. The more sensitive method, based on the Fe-CAS-ODTA-TX100 system, has been applied to the determination of iron in cereals. To evaluate the accuracy of the elaborated method, the determined content of Fe was compared to the declared value as well as to the result obtained by the reference ICP-OES method.     

A simple and fast liquid chromatography–tandem mass spectrometry method for measurement of underivatized <Emphasis Type="SmallCaps">l</Emphasis>-arginine,symmetric dimethylarginine,and asymmetric dimethylarginine and establishment of the reference ranges

Asymmetric dimethylarginine (ADMA) is an endogenous inhibitor of nitric oxide synthase and an established biomarker for endothelial function, while symmetric dimethylarginine (SDMA), an emerging biomarker for renal function, has been shown to outperform creatinine-based equations for estimated glomerular filtration rate. In order to study these analytes for clinical research, a fast and simple method for measuring arginine (ARG), SDMA, and ADMA in plasma by liquid chromatography–tandem mass spectrometry (LC-MS/MS) has been developed. Plasma (50 μL) was mixed with 50 μL of internal standard of ¹³C-arginine and d₇-ADMA followed by protein precipitation with methanol containing 1% ammonium acetate (300 μL). After centrifugation, the supernatant (100 μL) was mixed with 300 μL of acetonitrile with 1% formic acid, and the mixture was injected onto a silica column monitored by a mass spectrometer. The analytical cycle time was 5.0 min. The method was linear from 5.7 to 489.7 μM for ARG, 0.06 to 5.15 μM for SDMA, and from 0.34 to 5.65 μM for ADMA, with an accuracy of 99.0–120.0%. Total coefficients of variation for all analytes ranged from 2.7% to 7.7% for three concentration levels. The effects of hemolysis, lipemia, uremia, icterus, specimen tube types, storage at different temperature, and freeze/thaw were thoroughly investigated. Reference ranges were established using 51 well-defined reference subjects (12 men and 39 women, age 19–64 years): 53.1–129.7 μM for ARG, 0.32–0.65 μM for SDMA, and 0.36–0.67 μM for ADMA. In conclusion, the validated LC-MS/MS method described here offers a fast and reliable ARG, SDMA, and ADMA quantitation in plasma with minimum sample preparation.     

Colorimetric determination of iron in infant fortified formulas by sequential injection analysis

 A procedure is described for the colorimetric determination of iron in infant fortified formulas based on sequential injection analysis (SIA). Iron(III) complexation with thiocyanate is used as colour developing reaction. The system enables the determination of iron in the samples (after digestion by dry ashing and treatment with 0.2 mol/L nitric acid in the range of 0.50–20.0 mg/L, consuming 140 μL of the sample and 8 mg thiocyanate per determination. The reactor geometry and the adjustment of the ionic content of the calibration solutions is important for the accuracy of the results. A regression line according to the equation [Fe(III) (mg/L)]_SIA=−0.3(±0.4)+1.03(±0.04) [Fe(III) (mg/L)]_FAAS was obtained after comparative analysis of a set of 12 samples. The measurement rate was 34 s, thus allowing to analyze 100 samples per hour with a relative standard deviation lower than 2%. Received: 30 July 1996/Revised: 1 October 1996/Accepted: 4 October 1996     

Speciation analysis of inorganic antimony in soil using HPLC-ID-ICP-MS

Speciation analysis of Sb(III) and Sb(V) in a soil sample was performed through extraction and on-line isotope dilution concentration determination after a chromatographic separation. The total Sb concentration found in a through traffic contaminated soil sample was (4.17 μg g⁻¹, 0.3 μg g⁻¹ SD, n=6). It was determined using ICP-MS after soil digestion using the sodium peroxide sintering method. The optimized extraction procedure for speciation analysis was carried out using 100 mmol L⁻¹ citric acid at pH 2.08 by applying an ultrasonic bath for 45 min at room temperature. The effects of citric acid concentration (0–500 mmol L⁻¹), pH (1–6), and temperature (30–60°C) on inorganic antimony species distribution in the examined sample were studied and optimized. The separation of Sb(III) and Sb(V) was achieved using an anion exchange column (PRP-X100) and 10 mmol L⁻¹ EDTA and 1 mmol L⁻¹ phthalic acid at pH 4.5 as a mobile phase. The eluent from the HPLC was mixed with an enriched (94.2%) ¹²³Sb spike solution that was pumped by a peristaltic pump with a constant flow rate (0.5 mL min⁻¹) in a three-way valve. The blend passed directly to the Conikal nebulizer of the ICP-MS. By using the above extraction procedure and methodology, 43.2% Sb(V) (2.9% RSD, n=3) and 6.0% Sb(III) (1.3% RSD, n=3) of total Sb found in the sample could be detected. The detection limits achieved by the proposed method were 20 ng L⁻¹ and 65 ng L⁻¹ for Sb(V) and Sb(III), respectively. The precision, evaluated by using RSD with 100 ng L⁻¹ calibration solutions, was 2.7% and 3.2% (n=6) for Sb(V) and Sb(III), respectively, in aqueous solutions.     

Determination of biogenic amines in food by automated pre-column derivatization with 2-naphthyloxycarbonyl chloride (NOC-CI)

Summary The fluorogenic reagent 2-naphthyloxycarbonyl chloride (NOC-Cl) has been used for the automated precolumn derivatization of biogenic amines (BAs) at ambient followed by liquid-chromatographic separation of the derivatives formed. For optimized derivatization samples in 0.5 M borate buffer (pH 9.0) were derivatized with 5 mM NOC-Cl in acetonitrile (MeCN) for 3 minutes. Excess of reagent was scavenged by addition of 20 mM glycine in water. For HPLC a Superspher^? RP-18e column and gradient elution using 0.1 M sodium acetate buffer (pH 4.4) and MeCN were used. The NOC-derivatives were detected by fluorescence at an emission wavelength of 335 nm at an excitation wavelength of 274 nm. This method allows the detection of BAs (2-phenylethylamine, putrescine, histamine, cadaverine, tyramine, spermidine, spermine) found in food and beverages (fruit juices, wines, various vinegars, fermented cabbage juice, and salmon). Detection limit of BAs are approximately 49–113 μg kg⁻¹ with the exception of histamine (747 μg kg⁻¹) (injected amounts: 18–41 pg histamine 267 pg), at a signalto-noise ratio of 3:1. The limits of determination are approximately 82–189 μg kg⁻¹ (histamine 1245 μg kg⁻¹) at a signal-to-noise ratio of 5:1. The correlation coefficients of linearity are 0.9910–0.9976. Recoveries from different matrices range from 65 to 109%, depending on the sample investigated. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996.     

Simultaneous voltammetric detection of dopamine and uric acid in the presence of high concentration of ascorbic acid using multi-walled carbon nanotubes with methylene blue composite film-modified electrode

An electrochemically functional nanocomposite through the adsorption of methylene blue onto the multi-walled nanotubes (MB-MWNTs) was prepared, and a sensitive voltammetric sensor was fabricated. The modified electrode showed excellent electrocatalytic activity toward dopamine (DA) and uric acid (UA) in 0.1 M phosphate solution medium (pH 3.0). Compared to the bare electrode, the MB-MWNTs film-modified electrode not only remarkably enhanced the anodic peak currents of DA and UA, i.e., shifted the anodic peak potential of DA negatively, but also avoided the overlapping of the anodic peaks of DA and UA. The interference of ascorbic acid (AA) was eliminated. Under the optimized conditions, the peak separation between AA and DA and between DA and UA was 219 and 174 mV, respectively. In the presence of 1.0 mM AA and 10.0 μM UA, the anodic peak current was linear to the concentration of DA in the range of 0.4–10.0 μM with a detection limit of 0.2 μM DA. The anodic peak current of UA was linear to the concentration in the range of 2.0–20.0 and 20.0–200.0 μM with a lowest detection limit of 1.0 μM in the presence of 1.0 mM AA and 1.0 μM DA.     

Application of computer imaging,stripping voltammetry and mass spectrometry to study the effect of lead (Pb-EDTA) on the growth and viability of early somatic embryos of Norway spruce (<Emphasis Type="Italic">Picea abies</Emphasis> /L./ Karst.)

Image analysis (IA) was used to determine the areas and circumferences of clusters of early somatic embryos (ESEs) of the Norway spruce (Picea abies /L./Karst.). Results obtained from IA were compared with the fresh weights of the ESE clusters and their esterase activities. The areas of the ESE clusters correlated well with both the increases in fresh weight (R ²=0.99) of the ESEs and their esterase activities (R ²=0.99). In addition, we studied the viability of the ESEs, which was determined by (a) double staining with fluorescein diacetate and propidium iodide (the resulting fluorescence was quantified by IA) and (b) determining esterase activity using a spectrofluorimetric detector. The results obtained with IA and esterase assay were comparable (the deviation between the tangents of the bisectors was 6.4%). IA was also used to study the effect of Pb–EDTA chelate (50, 250 and 500 μM) on the viability of the ESEs and on the growth of clusters. The presence of Pb–EDTA markedly slowed the growth of ESEs clusters (by more than 65% with 250 μM of Pb–EDTA after 288 h of cultivation) and decreased the viability of ESEs (by more than 30% with 500 μM of Pb–EDTA after 288 h of cultivation). The lead concentration in the ESEs was determined by differential pulse anodic stripping voltammetry and increased with the external lead concentration and the time of treatment from 100 to 600 pg Pb/100 mg of fresh weight of ESEs. Glutathione is a diagnostic marker of the influence of Pb–EDTA on ESEs and its content was determined by high–performance liquid chromatography coupled with mass spectrometry. The glutathione content changed linearly with treatment time and the applied external lead concentration. The highest glutathione content was obtained at 250 μM of Pb–EDTA after 192 h of cultivation.