Harvesting the Vibration Energy of BiFeO3 Nanosheets for Hydrogen Evolution

In this study, mechanical vibration is used for hydrogen generation and decomposition of dye molecules, with the help of BiFeO₃ (BFO) square nanosheets. A high hydrogen production rate of ≈124.1 μmol g^?1 is achieved under mechanical vibration (100 W) for 1 h at the resonant frequency of the BFO nanosheets. The decomposition ratio of Rhodamine B dye reaches up to ≈94.1 % after mechanical vibration of the BFO catalyst for 50 min. The vibration‐induced catalysis of the BFO square nanosheets may be attributed to the piezocatalytic properties of BFO and the high specific surface area of the nanosheets. The uncompensated piezoelectric charges on the surfaces of BFO nanosheets induced by mechanical vibration result in a built‐in electric field across the nanosheets. Unlike a photocatalyst for water splitting, which requires a proper band edge position for hydrogen evolution, such a requirement is not needed in piezocatalytic water splitting, where the band tilting under the induced piezoelectric field will make the conduction band of BFO more negative than the H₂/H₂O redox potential (0 V) for hydrogen generation.     

Synthesis of Tri‐functional Core‐shell CuO@carbon Quantum Dots@carbon Hollow Nanospheres Heterostructure for Non‐enzymatic H2O2 Sensing and Overall Water Splitting Applications

A core‐shell structure with CuO core and carbon quantum dots (CQDs) and carbon hollow nanospheres (CHNS) shell was prepared through facile in‐situ hydrothermal process. The composite was used for non‐enzymatic hydrogen peroxide sensing and electrochemical overall water splitting. The core‐shell structure was established from the transmission electron microscopy image analysis. Raman and UV‐Vis spectroscopy analysis confirmed the interaction between CuO and CQDs. The electrochemical studies showed the limit of detection and sensitivity of the prepared composite as 2.4 nM and 56.72 μA μM^?1 cm^?2, respectively. The core‐shell structure facilitated better charge transportation which in turn exhibited elevated electro‐catalysis towards hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and overall water splitting. The overpotential of 159 mV was required to achieve 10 mA cm^?2 current density for HER and an overpotential of 322 mV was required to achieve 10 mA cm^?2 current density for OER in 1.0 M KOH. A two‐electrode system was constructed for overall water splitting reaction, which showed 10 and 50 mA cm^?2 current density at 1.83 and 1.96 V, respectively. The prepared CuO@CQDs@CHNS catalyst demonstrated excellent robustness in HER and OER catalyzing condition along with overall water splitting reaction. Therefore, the CuO@CQDs@CHNS could be considered as promising electro‐catalyst for H₂O₂ sensing, HER, OER and overall water splitting.     

Electro‐Mechanochemical Atom Transfer Radical Cyclizations using Piezoelectric BaTiO3

The formation and regeneration of active Cu^I species is a fundamental mechanistic step in copper‐catalyzed atom transfer radical cyclizations (ATRC). Typically, the presence of the catalytically active Cu^I species in the reaction mixture is secured by using high Cu^I catalyst loadings or the addition of complementary reducing agents. In this study it is demonstrated how the piezoelectric properties of barium titanate (BaTiO₃) can be harnessed by mechanical ball milling to induce electrical polarization in the strained piezomaterial. This strategy enables the conversion of mechanical energy into electrical energy, leading to the reduction of a Cu^II precatalyst into the active Cu^I species in copper‐catalyzed mechanochemical solvent‐free ATRC reactions.     

Efficient One-Pot Microwave-Assisted Hydrothermal Synthesis of Nitrogen-Doped TiO2 for Hydrogen Production by Photocatalytic Water Splitting

Develop a photocatalyst system for solar energy conversion to electric energy or chemical energy is a topic of great interest for fundamental and practical importance. In this study, nitrogen-doped TiO₂ with high hydrogen production by photocatalytic water splitting were prepared by microwave-assisted hydrothermal method using titanium sulfate as precursor in the presence of urea. The nitrogen doped TiO₂ prepared in this study was pure anatase phase with a high surface area (372?m²?g^?1) and showed a very high hydrogen evolution rate of water splitting reaction under UV light irradiation (4,386?μmol?g^?1?h^?1) and visible light irradiation (185?μmol?g^?1?h^?1) which was about 15?times higher than commercial TiO₂ (Degussa P25).     

Heterostructure of Si and CoSe2: A Promising Photocathode Based on a Non‐noble Metal Catalyst for Photoelectrochemical Hydrogen Evolution

Development of a solar water splitting device requires design of a low‐cost, efficient, and non‐noble metal compound as alternative to noble metals. For the first time, we showed that CoSe₂ can function as co‐catalyst in phototoelectrochemical hydrogen production. We designed a heterostructure of p‐Si and marcasite‐type CoSe₂ for solar‐driven hydrogen production. CoSe₂ successively coupled with p‐Si can act as a superior photocathode in the solar‐driven water splitting reaction. Photocurrents up to 9 mA cm^?2 were achieved at 0 V vs. reversible hydrogen electrode. Electrochemical impedance spectroscopy showed that the high photocurrents can be attributed to low charge transfer resistance between the Si and CoSe₂ interfaces and that between the CoSe₂ and electrolyte interfaces. Our results suggest that this CoSe₂ is a promising alternative co‐catalyst for hydrogen evolution.     

Mechanically Activated Solid-State Radical Polymerization and Cross-Linking via Piezocatalysis

Piezocatalysis offers a means to transduce mechanical energy into chemical potential, harnessing physical force to drive redox reactions. Working in the solid state, we show here that piezoelectric BaTiO₃ nanoparticles can transduce mechanical load into a flux of reactive radical species capable of initiating solid state free radical polymerization. Activation of a BaTiO₃ powder by ball milling, striking with a hammer, or repeated compressive loading generates highly reactive hydroxyl radicals (⋅OH), which readily initiate radical chain growth and crosslinking of solid acrylamide, acrylate, methacrylate and styrenic monomers. Control experiments indicate a critical role for chemisorbed water on the BaTiO₃ nanoparticle surface, which is oxidized to ⋅OH via mechanoredox catalysis. The force-induced production of radicals by compressing dry piezoelectric materials represents a promising new route to harness mechanical energy for solid state radical synthesis.     

A Hydrogen Farm Strategy for Scalable Solar Hydrogen Production with Particulate Photocatalysts

Scalable solar hydrogen production by water splitting using particulate photocatalysts is promising for renewable energy utilization. However, photocatalytic overall water splitting is challenging owing to slow water oxidation kinetics, severe reverse reaction, and H₂/O₂ gas separation. Herein, mimicking nature photosynthesis, a practically feasible approach named Hydrogen Farm Project (HFP) is presented, which is composed of solar energy capturing and hydrogen production subsystems integrated by a shuttle ion loop, Fe³⁺/Fe²⁺. Well‐defined BiVO₄ crystals with precisely tuned {110}/{010} facets are ideal photocatalysts to realize the HFP, giving up to 71 % quantum efficiency for photocatalytic water oxidation and full forward reaction with nearly no reverse reaction. An overall solar‐to‐chemical efficiency over 1.9 % and a solar‐to‐hydrogen efficiency exceeding 1.8 % could be achieved. Furthermore, a scalable HFP panel for solar energy storage was demonstrated under sunlight outdoors.     

Bifunctional Electrocatalysts for Overall Water Splitting from an Iron/Nickel‐Based Bimetallic Metal–Organic Framework/Dicyandiamide Composite

Pyrolysis of a bimetallic metal–organic framework (MIL‐88‐Fe/Ni)‐dicyandiamide composite yield a Fe and Ni containing carbonaceous material, which is an efficient bifunctional electrocatalyst for overall water splitting. FeNi₃ and NiFe₂O₄ are found as metallic and metal oxide compounds closely embedded in an N‐doped carbon–carbon nanotube matrix. This hybrid catalyst (Fe‐Ni@NC‐CNTs) significantly promotes the charge transfer efficiency and restrains the corrosion of the metallic catalysts, which is shown in a high OER and HER activity with an overpotential of 274 and 202 mV, respectively at 10 mA cm^?2 in alkaline solution. When this bifunctional catalyst was further used for H₂ and O₂ production in an electrochemical water‐splitting unit, it can operate in ambient conditions with a competitive gas production rate of 1.15 and 0.57 μL s^?1 for hydrogen and oxygen, respectively, showing its potential for practical applications.     

Fabrication of NiC/MoC/NiMoO4 Heterostructured Nanorod Arrays as Stable Bifunctional Electrocatalysts for Efficient Overall Water Splitting

Developing noble‐metal‐free, earth‐abundant, highly active, and stable electrocatalysts with high efficiency for both hydrogen and oxygen evolution reactions is of great importance for the development of overall water‐splitting devices, but still remains a challenging issue. Herein, a 3D heterostructured NiC/MoC/NiMoO₄ electrocatalyst was prepared through a facile synthetic procedure. The electrocatalyst shows a superior catalytic activity and stability toward the hydrogen and oxygen evolution reactions. The optimized NiC/MoC/NiMoO₄ catalyst presents low overpotentials of 68 and 280 mV to reach a current density of 10 mA cm^?2 in 1.0 m KOH for the hydrogen and oxygen evolution reactions, respectively. Assembled as an electrolyzer for overall water splitting, such a heterostructure shows quite a low cell voltage of 1.52 V at 10 mA cm^?2 and remarkable stability for more than 20 h. This work provides a facile but efficient approach for the design and preparation of highly efficient bifunctional and self‐supported heterostructured electrocatalysts that can serve as promising candidates in electrochemical energy storage and conversion.     

Electro-Mechanochemical Atom Transfer Radical Cyclizations using Piezoelectric BaTiO3

The formation and regeneration of active Cu^I species is a fundamental mechanistic step in copper-catalyzed atom transfer radical cyclizations (ATRC). Typically, the presence of the catalytically active Cu^I species in the reaction mixture is secured by using high Cu^I catalyst loadings or the addition of complementary reducing agents. In this study it is demonstrated how the piezoelectric properties of barium titanate (BaTiO₃) can be harnessed by mechanical ball milling to induce electrical polarization in the strained piezomaterial. This strategy enables the conversion of mechanical energy into electrical energy, leading to the reduction of a Cu^II precatalyst into the active Cu^I species in copper-catalyzed mechanochemical solvent-free ATRC reactions.     

Highly Efficient Photocatalytic H2 Evolution from Water using Visible Light and Structure‐Controlled Graphitic Carbon Nitride

The major challenge of photocatalytic water splitting, the prototypical reaction for the direct production of hydrogen by using solar energy, is to develop low‐cost yet highly efficient and stable semiconductor photocatalysts. Herein, an effective strategy for synthesizing extremely active graphitic carbon nitride (g‐C₃N₄) from a low‐cost precursor, urea, is reported. The g‐C₃N₄ exhibits an extraordinary hydrogen‐evolution rate (ca. 20 000 μmol h^?1 g^?1 under full arc), which leads to a high turnover number (TON) of over 641 after 6 h. The reaction proceeds for more than 30 h without activity loss and results in an internal quantum yield of 26.5 % under visible light, which is nearly an order of magnitude higher than that observed for any other existing g‐C₃N₄ photocatalysts. Furthermore, it was found by experimental analysis and DFT calculations that as the degree of polymerization increases and the proton concentration decreases, the hydrogen‐evolution rate is significantly enhanced.     

Transparent Ta3N5 Photoanodes for Efficient Oxygen Evolution toward the Development of Tandem Cells

Photoelectrochemical water splitting is regarded as a promising approach to the production of hydrogen, and the development of efficient photoelectrodes is one aspect of realizing practical systems. In this work, transparent Ta₃N₅ photoanodes were fabricated on n‐type GaN/sapphire substrates to promote O₂ evolution in tandem with a photocathode, to realize overall water splitting. Following the incorporation of an underlying GaN layer, a photocurrent of 6.3 mA cm^?2 was achieved at 1.23 V vs. a reversible hydrogen electrode. The transparency of Ta₃N₅ to wavelengths longer than 600 nm allowed incoming solar light to be transmitted to a CuInSe₂ (CIS), which absorbs up to 1100 nm. A stand‐alone tandem cell with a serially‐connected dual‐CIS unit terminated with a Pt/Ni electrode was thus constructed for H₂ evolution. This tandem cell exhibited a solar‐to‐hydrogen energy conversion efficiency greater than 7 % at the initial stage of the reaction.     

Noble‐Metal‐Free Janus‐like Structures by Cation Exchange for Z‐Scheme Photocatalytic Water Splitting under Broadband Light Irradiation

Z‐scheme water splitting is a promising approach based on high‐performance photocatalysis by harvesting broadband solar energy. Its efficiency depends on the well‐defined interfaces between two semiconductors for the charge kinetics and their exposed surfaces for chemical reactions. Herein, we report a facile cation‐exchange approach to obtain compounds with both properties without the need for noble metals by forming Janus‐like structures consisting of γ‐MnS and Cu₇S₄ with high‐quality interfaces. The Janus‐like γ‐MnS/Cu₇S₄ structures displayed dramatically enhanced photocatalytic hydrogen production rates of up to 718 μmol g⁻¹ h⁻¹ under full‐spectrum irradiation. Upon further integration with an MnO_x oxygen‐evolution cocatalyst, overall water splitting was accomplished with the Janus structures. This work provides insight into the surface and interface design of hybrid photocatalysts, and offers a noble‐metal‐free approach to broadband photocatalytic hydrogen production.     

Synthesis of Ni–Ru Alloy Nanoparticles and Their High Catalytic Activity in Dehydrogenation of Ammonia Borane

We report the synthesis and characterization of new Ni_xRu_1?x (x=0.56–0.74) alloy nanoparticles (NPs) and their catalytic activity for hydrogen release in the ammonia borane hydrolysis process. The alloy NPs were obtained by wet‐chemistry method using a rapid lithium triethylborohydride reduction of Ni²⁺ and Ru³⁺ precursors in oleylamine. The nature of each alloy sample was fully characterized by TEM, XRD, energy dispersive X‐ray spectroscopy (EDX), and X‐ray photoelectron spectroscopy (XPS). We found that the as‐prepared Ni–Ru alloy NPs exhibited exceptional catalytic activity for the ammonia borane hydrolysis reaction for hydrogen release. All Ni–Ru alloy NPs, and in particular the Ni_0.74Ru_0.26 sample, outperform the activity of similar size monometallic Ni and Ru NPs, and even of Ni@Ru core‐shell NPs. The hydrolysis activation energy for the Ni_0.74Ru_0.26 alloy catalyst was measured to be approximately 37 kJ mol^?1. This value is considerably lower than the values measured for monometallic Ni (≈70 kJ mol^?1) and Ru NPs (≈49 kJ mol^?1), and for Ni@Ru (≈44 kJ mol^?1), and is also lower than the values of most noble‐metal‐containing bimetallic NPs reported in the literature. Thus, a remarkable improvement of catalytic activity of Ru in the dehydrogenation of ammonia borane was obtained by alloying Ru with a Ni, which is a relatively cheap metal.     

Strong‐Base‐Assisted Synthesis of a Crystalline Covalent Triazine Framework with High Hydrophilicity via Benzylamine Monomer for Photocatalytic Water Splitting

Methods to synthesize crystalline covalent triazine frameworks (CTFs) are limited and little attention has been paid to development of hydrophilic CTFs and photocatalytic overall water splitting. A route to synthesize crystalline and hydrophilic CTF‐HUST‐A1 with a benzylamine‐functionalized monomer is presented. The base reagent used plays an important role in the enhancement of crystallinity and hydrophilicity. CTF‐HUST‐A1 exhibits good crystallinity, excellent hydrophilicity, and excellent photocatalytic activity in sacrificial photocatalytic hydrogen evolution (hydrogen evolution rate up to 9200 μmol g^?1 h^?1). Photocatalytic overall water splitting is achieved by depositing dual co‐catalysts in CTF‐HUST‐A1, with H₂ evolution and O₂ evolution rates of 25.4 μmol g^?1 h^?1 and 12.9 μmol g^?1 h^?1 in pure water without using sacrificial agent.     

Visible Light Photocatalytic Activity of Pt/N‐TiO2 towards Enhanced H2 Production from Water Splitting

Present work mainly focuses on experimental investigation to improvement of hydrogen production by water photoelectrolysis. An experimental facility was designed and constructed for visible light photocatalysis. A series of N‐TiO₂ photocatalysts impregnated with platinum on the surface of N‐TiO₂ were prepared. Hydrogen production upon irradiating aqueous Pt/N‐TiO₂ suspension with visible light was investigated. The shift in excitation wavelength of TiO₂ was 380 nm improved the yield of hydrogen production by N‐TiO₂ and Pt/N‐TiO₂. We used a 400 W mercury arc lamp combined with a 400 nm cutoff filter eliminating all the wavelengths under 400 nm. Pt/N‐TiO₂ material was characterized with TPR, reflective UV/Visible spectroscopy and TEM. The best hydrogen production rate obtained for this setup for N/Ti = 10, 0.05 wt% Pt/N‐TiO₂, through water splitting was about 772 μmolh^?1g^?1.     

Hierarchical NiCo2O4 Hollow Microcuboids as Bifunctional Electrocatalysts for Overall Water‐Splitting

Bifunctional electrocatalysts for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in alkaline electrolyte may improve the efficiency of overall water splitting. Nickel cobaltite (NiCo₂O₄) has been considered a promising electrode material for the OER. However, NiCo₂O₄ that can be used as an electrocatalyst in HER has not been studied yet. Herein, we report self‐assembled hierarchical NiCo₂O₄ hollow microcuboids for overall water splitting including both the HER and OER reactions. The NiCo₂O₄ electrode shows excellent activity toward overall water splitting, with 10 mA cm^?2 water‐splitting current reached by applying just 1.65 V and 20 mA cm^?2 by applying just 1.74 V across the two electrodes. The synthesis of NiCo₂O₄ microflowers confirms the importance of structural features for high‐performance overall water splitting.     

An Efficient,Visible‐Light‐Driven,Hydrogen Evolution Catalyst NiS/ZnxCd1−xS Nanocrystal Derived from a Metal–Organic Framework

Photocatalytic water splitting for hydrogen production using sustainable sunlight is a promising alternative to industrial hydrogen production. However, the scarcity of highly active, recyclable, inexpensive photocatalysts impedes the development of photocatalytic hydrogen evolution reaction (HER) schemes. Herein, a metal–organic framework (MOF)‐template strategy was developed to prepare non‐noble metal co‐catalyst/solid solution heterojunction NiS/Zn_xCd_1?xS with superior photocatalytic HER activity. By adjusting the doping metal concentration in MOFs, the chemical compositions and band gaps of the heterojunctions can be fine‐tuned, and the light absorption capacity and photocatalytic activity were further optimized. NiS/Zn_0.5Cd_0.5S exhibits an optimal HER rate of 16.78 mmol g^?1 h^?1 and high stability and recyclability under visible‐light irradiation (λ>420 nm). Detailed characterizations and in‐depth DFT calculations reveal the relationship between the heterojunction and photocatalytic activity and confirm the importance of NiS in accelerating the water dissociation kinetics, which is a crucial factor for photocatalytic HER.     

Improving piezoelectric performance of lead-free polymer composites with high aspect ratio BaTiO3 nanowires

Flexible and lead-free piezoelectric nanocomposites were synthesized with BaTiO₃ nanowires (filler) and poly(vinylidene fluoride) (PVDF) (matrix), and the piezoelectric performances of the composites were systematically studied by varying the aspect ratio (AR) and volume fraction of the nanowire and poling time. BaTiO₃ nanowires with AR of 18 were synthesized and incorporated into PVDF to improve the piezoelectric performance of the composites. It was found that high AR significantly increased the dielectric constant up to 64, which is over 800% improvement compared to those from the composites containing spheroid shape BaTiO₃ nanoparticles. In addition, the dielectric constant and piezoelectric coefficient were also enhanced by increasing the concentration of BaTiO₃ nanowires. The piezoelectric coefficient with 50-vol% BaTiO₃ nanowires embedded in PVDF displayed 61 pC/N, which is much higher than nanocomposites with spheroid shape BaTiO₃ nanoparticles as well as comparable to, if not better, other nanoparticle-filled polymer composites. Our results suggest that it is possible to fabricate nanocomposites with proper mechanical and piezoelectric properties by utilizing proper AR fillers.     

Highly Dispersed TiO6 Units in a Layered Double Hydroxide for Water Splitting

A family of photocatalysts for water splitting into hydrogen was prepared by distributing TiO₆ units in an MTi‐layered double hydroxide matrix (M=Ni, Zn, Mg) that displays largely enhanced photocatalytic activity with an H₂‐production rate of 31.4 μmol h^?1 as well as excellent recyclable performance. High‐angle annular dark‐field scanning transmission electron microscopy (HAADF‐STEM) mapping and XPS measurement reveal that a high dispersion of TiO₆ octahedra in the layered doubled hydroxide (LDH) matrix was obtained by the formation of an M²⁺‐O‐Ti network, rather different from the aggregation state of TiO₆ in the inorganic layered material K₂Ti₄O₉. Both transient absorption and photoluminescence spectra demonstrate that the electron–hole recombination process was significantly depressed in the Ti‐containing LDH materials relative to bulk Ti oxide, which is attributed to the abundant surface defects that serve as trapping sites for photogenerated electrons verified by positron annihilation and extended X‐ray absorption fine structure (EXAFS) techniques. In addition, a theoretical study on the basis of DFT calculations demonstrates that the electronic structure of the TiO₆ units was modified by the adjacent MO₆ octahedron by means of covalent interactions, with a much decreased bandgap of 2.1 eV, which accounts for its superior water‐splitting behavior. Therefore, the dispersion strategy for TiO₆ units within a 2D inorganic matrix can be extended to fabricate other oxide or hydroxide catalysts with greatly enhanced performance in photocatalysis and energy conversion.