Crystallographic and magnetic properties of (Nd,Dy)3Fe27.5(Ti,Mo)1.5 compounds

A systematic study of the formation, structure and magnetic properties of (Nd,Dy)₃Fe_27.5(Ti,Mo)_1.5 compounds has been performed. Rietveld analyses of the X-ray patterns of the samples indicate that the concentrations of Ti and Mo affect the formation and structural properties slightly, whereas different rare-earth (Nd and Dy) contents influence them significantly. It is found that high Dy contents make it difficult to form the 3:29-type structures. The Curie temperatures of Nd_2.1Dy_0.9Fe_27.5Ti_1.5−xMo_x decrease monotonically as more Ti was replaced by Mo but their saturation magnetizations remain almost unchanged; in contrast, for Nd_3−yDy_yFe_27.5TiMo_0.5, their saturation magnetizations decrease monotonically with increasing Dy contents while their Curie temperatures are constant.     

Preparation of substituted barium ferrite BaFe12−x(Ti0.5Co0.5)xO19 by citrate precursor method and compositional dependence of their magnetic properties

As a possible candidate for the left-handed metamaterial with negative permeability, a series of Ti, Co-substituted M-type barium hexaferrite BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ (x=0, 1, 2, 3, 4 and 5) was prepared by citrate precursor method. The formation processes of the substituted barium hexaferrite compounds from the precursors were followed by the measurements of powder X-ray diffraction (XRD), Infrared absorption spectra (FT-IR), and thermogravimetry and differential thermal analysis (TG/DTA) coupled with mass spectroscopy (MS). In the case of the non-substituted sample, the formation of the barium hexaferrite is regulated by the thermal decomposition of BaCO₃ and the solid-state reactions of BaO and Fe₂O₃ in the temperature range from 800 to 1100 K. The formation temperature of the substituted BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ is higher than that for the non-substituted sample and increases with the value of x, due to the effects of carbonate ions incorporated by the partial substitution of Fe³⁺ by (Ti_0.5Co_0.5)³⁺. On heating up to ca. 1200 K, all the substituted samples transform into the magenetoplumbite phase as is the non-substituted sample. The compositional dependence of the magnetic properties of the substituted barium hexaferrite was investigated by the magnetization measurement. The decrease in the magnetic anisotropy was confirmed by the change in the magnetization curve and coercivity H_C with the composition x. A negative permeability spectrum was observed in the BaFe₉(Ti_0.5Co_0.5)₃O₁₉ in the frequency range from 2 to 4 GHz.     

Ferromagnetism of epitaxially grown CaRu1−xMxO3 (M=Ti, Mn) films

Epitaxial thin films of CaRu_1−xM_xO₃ (M=Ti, Mn) were fabricated on a (0 0 1)-SrTiO₃ substrate by spin-coat method using organometallic solutions (metal alkoxides). Results of X-ray diffraction and transmission electron microscopy indicate that the epitaxial films were grown pseudomorphically so as to align the [0 0 l] axis of the CaRu_1−xM_xO₃ films perpendicular to the (0 0 1) plane of the SrTiO₃ substrate. Ferromagnetism and metal-insulator transition are induced by the substitution of transition metal ions. The occurrence of ferromagnetism was explained qualitatively assuming a TiRu₆ cluster model for CaRu_1−xTi_xO₃ film and a mixed valence model for CaRu_1−xMn_xO₃ film. Ferromagnetism was also observed for layered CaRuO₃/CaMnO₃ film and CaRuO₃/CaMnO₃/CaRuO₃/CaMnO₃ multilayer film and the magnetism was explained by an interfacial exchange interaction model with magnetic Mn³⁺, Mn⁴⁺, and Ru⁵⁺ ions.     

Structure and magnetic properties of SmCoxTi0.4-1:7 ribbons

SmCo_xTi_0.4 (x=6.6, 7.1, 7.6, 8.1) ribbons have been prepared by melt spinning at a wheel speed of 42 m/s, followed by annealing at 750 °C for 2 h. Both as-spun and as-annealed ribbons possess the disordered TbCu7-type (1:7) phase even when the Sm/(Co,Ti) atomic ratio deviates from 1/7. The c/a ratio increases with increasing Co concentration x, but the unit cell volume decreases. The Curie temperatures show above 700 °C, increasing from 707 °C for x=6.6 to 782 °C for x=8.1. The saturation magnetizations increase almost linearly with increasing Co content. The observed magnetic hardening is believed to arise from the high magnetocrystalline anisotropy of the 1:7 phase and the fine nanograin structure. The intrinsic coercivity of 9797 Oe has been obtained in the melt-spun SmCo_7.1Ti_0.4 ribbons.     

Vacuum ultraviolet luminescence from a micro-pulling-down method grown Nd:(La0.9,Ba0.1)F2.9

Vacuum ultraviolet (VUV) luminescence from a Nd³⁺:(La_1−x,Ba_x)F_3−x (x=0.1) and a Nd³⁺:LaF₃ single crystal grown by the micro-pulling-down method modified for fluoride crystal growth is discussed. Emission resulting from excitation with 157 nm pulses of a F₂ laser and by 290 nm femtosecond pulses of a Ti:sapphire laser show that the luminescence spectral and temporal characteristics are similar for both excitation cases and that they have good prospects as a VUV laser material.     

Particle analysis and properties of mechanically alloyed Nd16Fe76−xTixB8

Nanocrystalline Nd₁₆Fe_76−xTi_xB₈ hard magnetic powders were prepared by mechanical alloying and respective heat treatment at 973–1073 K /30–60 min. The nanocrystalline hard magnetic powders were investigated by the NanoSight Halo LM10^TM Nanoparticle Analysis System, AFM, SEM and Mössbauer spectrometry. The nanocrystals have average size of 40 nm and the crystals form agglomerates with an average size of about 180 nm. Halo^TM, AFM and SEM techniques are the complementary methods, which give comparable results.     

Coercivity mechanism of Sm(Co, Cu)5

The mechanism of the high intrinsic coercivity of the Sm(Co_1−xCu_x)₅ (0≦x<1) system was studied by relating the coherency between the lattice constants of hexagonal Sm(Co, Cu)₅ and hcp Co to the coercive force. It was found analytically that the intrinsic coercive force reaches a maximum in the composition range from x=0.6 to 0.8, where the lattice mismatch approaches zero, so that there is a strong correlation between lattice matching and coercive force. When a Sm ion was located within a Sm(Co, Cu)₅ grain and in the outmost edge of the a and c planes of its grain surrounded or not surrounded by the coherent Co phase, the crystal field parameter at each Sm³⁺ site was calculated using a point charge model under the assumption that the Co and Cu atoms located in a grain and the hcp Co atoms situated at the interface uniformly have a charge of 3/5−. The results indicated that the Co phase precipitated coherently along the grain boundaries effectively enhances the magnetocrystalline anisotropy of Sm ions located in the outmost edges of the a and c planes of a Sm(Co, Cu)₅ grain.     

Preference orientation and magnetic properties of CoxFe3−xO4 nanocrystalline thin films on quartz substrate

Nanocrystalline spinel ferrite thin films of Co_xFe_3−xO₄ (x=0.3$x=0.3$, 0.5, 0.8, and 1.0) have been prepared by RF sputtering on quartz substrate without a buffer layer at room temperature and annealed at the temperature range from 200 to 600 °C in air. The as-sputtered films exhibit the preferred orientation and the high magnetization and coercivity. After annealing, the preferred orientations become poor, but the magnetization and coercivity increase. The sample with a magnetization of 455 emu/cm³, a coercivity of 2.8 kOe, a remanence ratio of 0.72, and a maximum energy product of 2.4 MGOe has been obtained. The influence of Co ions and annealing temperature on the magnetic properties has been discussed.     

Magnetostriction, Curie temperature and microstructure of Tb0.29(Dy1−xPrx)0.71Fe1.97 oriented alloys

The Tb_0.29(Dy_1−xPr_x)_0.71Fe_1.97 (x=0, 0.1, 0.2 and 0.3) alloys were prepared by directional solidification method. The orientation, magnetostriction λ, Curie temperature T_c and microstructure of alloys were characterized by XRD, standard resistant strain gauge technique, VSM and SEM-EDS. The results reveal that the alloys have a preferred orientation of 〈1 1 0〉 and 〈1 1 3〉 direction when x>0. With the increase in Pr content, the T_c of alloys decreases gradually and the non-cubic phase appears, resulting in the decline of λ dramatically, from 1935.2×10⁻⁶ for x=0 to 695.9×10⁻⁶ for x=0.3 at a compressive stress of 6 MPa and a magnetic field of H=240 kA m⁻¹.     

Refinement of the microstructure and enhancement of the magnetic properties in α-Fe/(Nd,Dy)2Fe14B nanocomposite using the two-step annealing technique

The Nd_8−xDy_xFe_87.5B_4.5 (x=0–1.0$x=0–1.0$) nanocomposites have been prepared by melt spinning and subsequent two-step heat treatment technique. The crystallization behaviors, microstructures and magnetic properties of the samples have been investigated. The experimental results show that the crystallization temperature of α-Fe soft phase has no obvious change through Dy addition while the crystallization temperature of 2:14:1 hard phase increases remarkably with increasing Dy content. By adopting a two-step heat treatment technique, a finer and more uniform microstructure can be developed. A dramatic enhancement of remanence J_r from 0.84 to 1.1 T, coercivity H_cj from 417 to 520 kA/m and energy product (BH)_m from 76.8 to 110 kJ/m³ have been obtained in Nd₇Dy₁Fe_87.5B_4.5 (30 vol%α-Fe ) nanocomposite.     

Magnetic and electrical properties of amorphous Ge1−xCrx thin films grown by low temperature vapor deposition

Amorphous Ge_1−xCr_x thin films are deposited on (1 0 0)Si by using a thermal evaporator. Amorphous phase is obtained when Cr concentration is lower than 30.7 at%. The electrical resistivities are 1.89×10⁻³–0.96×10² Ω cm at 300 K, and decrease with Cr concentration. The Ge_1−xCr_x thin films are p-type. The hole concentrations are 5×10¹⁶–7×10²¹ cm⁻³ at 300 K, and increase with Cr concentration. Magnetizations are 7.60–1.57 emu/cm³ at 5 K in the applied field of 2 T. The magnetizations decrease with Cr concentration and temperature. Magnetization characteristics show that the Ge_1−xCr_x thin films are paramagnetic.     

Structural and magnetic properties of Mg(In2−xMnx)O4 system

We synthesized the Mn-doped Mg(In_2−xMn_x)O₄ oxides with 0.03?x?0.55 using a solid-state reaction method. The X-ray diffraction patterns of the samples were in a good agreement with that of a distorted orthorhombic spinel phase. Their lattice parameters and unit-cell volumes decrease with x due to the substitution of the smaller Mn³⁺ ions to the larger In³⁺ ions. The undoped MgIn₂O₄ oxide presents diamagnetic signals for 5 K?T?300 K. The M(H) at T=300 K reveals a fairly negative-sloped linear relationship. Neither magnetic hysteresis nor saturation behavior was observed in this parent sample. For the Mn-doped samples, however, positive magnetization were observed between 5 and 300 K even if the x value is as low as 0.03. The mass susceptibility enhances with Mn content and it reaches the highest value of 1.4×10⁻³ emu/g Oe (at T=300 K) at x=0.45. Furthermore, the Mn-doped oxides with x=0.06 and 0.2, respectively, exhibit nonlinear magnetization curves and small hysteretic loops in low magnetic fields. Susceptibilities of the Mn-doped samples are much higher than those of MnO₂, Mn₂O₃ oxides, and Mn metals. These results show that the oxides have potential to be magnetic semiconductors.     

Microstructures and coercivities of SmCox and Sm(Co,Cu)5 films prepared by magnetron sputtering

We have investigated the influence of composition and annealing conditions on the magnetic properties and microstructural features of SmCo_x films that were prepared by sputtering and subsequent annealing. A huge in-plane coercivity of 5.6 T was obtained from an optimally annealed Sm–Co film, which was attributed to the nanometer sized polycrystalline microstructure of the highly anisotropic SmCo₅ phase. Although a high density of planar defects were observed in the films that were annealed at high temperatures, they did not act as strong pinning sites for domain wall motion. The effect of Cu on [SmCo_4.5(9 nm)/Cu(xnm)]₁₀ multilayer thin films was also studied. An appropriate Cu content increased the coercivity.     

Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Synthesis and structure refinement of layered perovskites Ba5−xLaxNb4−xTixO15 (x=0, 1, 2, 3 and 4) solid solutions

Ba_5−xLa_xNb_4−xTi_xO₁₅ solid solutions were prepared by solid state reaction method. Structural analysis for the stoichiometric phases was performed for x=0, 1, 2 and 3 by Rietveld analysis of neutron powder diffraction data. The x=0, 1 and 2 members could be refined in the space group P-3m1 (stacking sequence chhcc, polytypoid 5 H). There is a decrease in cell volume as x increases. La³⁺ occupies preferentially the A2 site (Wyckoff site 2d) and Ti⁴⁺ the B2 site (Wyckoff site 2c). As x increases there is an increase of the global instability index (GII) (which is a measure of the extent to which the BVS rule is violated over the whole structure) indicating the presence of intrinsic strains large enough to cause instability at room temperature. This strain is responsible for a structural change for the member with x=3, which could be refined in the space group P-3c1 (stacking sequence (chhcc)₂, polytypoid 2×5H=10H). This change in space group is associated with a cooperative rotation of (Nb/Ti)O₆ octahedra around the c-axis, necessary to accommodate the smaller La³⁺ ion in the cuboctahedral cavity.     

Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

Magnetotransport properties of (La0.7Pb0.3MnO3)1−xAgx composites

Magnetic and transport properties of (La_0.7Pb_0.3MnO₃)_1−xAg_x composites are explored in this study. Ferromagnetism is gradually attenuated due to the magnetic dilution with increase of Ag content percentage. Clearly irreversible behavior in the zero-field cooling and field cooling curves at a low field caused by the competition between the magnetization and magnetic domain orientation processes has been observed as x increases. Saturation magnetization decreases as x increases, while ferromagnetic transition temperature remains around 346 K for all composites. The resistivity decreases significantly for (La_0.7Pb_0.3MnO₃)_1−xAg_x composites. It is suggested that introduction of Ag into the niche of grain boundaries forms artificial conducting network and improves the carriers to transport. However, enhancement of magnetoresistance has been observed for the system.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Structural and magnetic properties of SmCo5.6Ti0.4 alloy

Three series of SmCo_5.6Ti_0.4 samples were prepared by quenching, melt spinning, and ball milling, respectively. Annealing at different temperatures was carried out for the three series. The influence of the processing routes on the structural and magnetic properties was systematically investigated for this alloy. The as-quenched bulk sample consisted of three phases with a rather coarse grain microstructure. Low intrinsic coercivity (_iH_c) of 0.12 T was obtained in this sample. While the as-spun ribbons and as-milled/annealed powders showed the CaCu₅-type phase (1:5) plus Th₂Zn₁₇-type phase (2:17), and the 1:5 phase plus TbCu₇-type phase (1:7), respectively, with nanograin microstructure. The _iH_c of as-spun ribbons and as-milled/annealed (700 °C for 2 h) powders was found to be 0.59 and 2.23 T, respectively. Coercivity mechanism of these as-spun ribbons is mainly of nucleation type. In the as-milled/annealed powders, the network of the nanograin boundaries is believed to provide strong pinning sites for the domain wall movement.     

Synthesis and magnetic characterization of cobalt-substituted ferrite (CoxFe3−xO4) nanoparticles

Cobalt-substituted ferrite nanoparticles were synthesized with a narrow size distribution using reverse micelles formed in the system water/AOT/isooctane. Fe:Co ratios of 3:1, 4:1, and 5:1 were used in the synthesis, obtaining cobalt-substituted ferrites (Co_xFe_3−xO₄) and some indication of γ-Fe₃O₄ when 4:1 and 5:1 Fe:Co ratios were used. Inductively coupled plasma mass spectroscopy (ICP-MS) verified the presence of cobalt in all samples. Fourier transform infrared (FTIR) showed bands at ∼560 and ∼400 cm⁻¹, characteristic of the metal–oxygen bond in ferrites. Transmission electron microscopy showed that the number median diameter of the particles was ∼3 nm with a geometric deviation of ∼0.2. X-ray diffraction (XRD) confirmed the inverse spinel structure typical of ferrites with a lattice parameter of a=8.388 Å for Co_0.61Fe_0.39O₄, which is near that of CoFe₂O₄ (a=8.394 Å). Magnetic properties were determined using a superconducting quantum interference device (SQUID). Coercivities higher than 8 kOe were observed at 5 K, whereas at 300 K the particles showed superparamagnetic behavior. The anisotropy constant was determined based on the Debye model for a magnetic dipole in an oscillating field and an expression relating χ′ and the temperature of the in-phase susceptibility peak. Anisotropy constant values in the order of ∼10⁶ erg/cm³ were determined using the Debye model, whereas anisotropy constants in the order of ∼10⁷ erg/cm³ were calculated assuming Ωτ=1 at the temperature peak of the in-phase component of the susceptibility curve as commonly done in the literature. Our analysis demonstrates that the assumption Ωτ=1 at the temperature peak of χ′ is rigorously incorrect.