PEROXIDASE MEDIATED CHEMILUMINESCENCE WITH PHENOL DERIVATIVES. PHYSICO-CHEMICAL PARAMETERS AND USES IN BIOLOGICAL ASSAYS

Abstract— The influence of pH and concentration of reagents on the chemiluminescence emitted during peroxidase mediated oxidation of phenol derivatives was studied. Maximal light emission was determined under conditions where chemiluminescence due to auto-oxidation was negligible. With phloroglucinol and purpurogallin as substrates, a direct proportionality was obtained between the concentration of peroxidase and the maximal light emission. p-Phenylenediamine enhances 8-fold the light emitted with purpurogallin. With resorcinol as substrate the relation between concentration of enzyme and maximal light emission gives an S-shaped curve. With pyrogallol the light emitted is proportional to the square of the concentration of peroxidase.     

Antioxidant effects of dihydroquercetin and rutin in peroxidase reactions catalyzed by cytochrome <Emphasis Type="Italic">c</Emphasis>

The combination of cytochrome c (Cyt c) and cardiolipin is known to catalyze free radical oxidation of membrane lipids, thereby triggering the cascade of reactions that lead to programmed cell death (apoptosis). It was interesting to estimate the possibility of controlling this reaction with the use of inhibitors of free radical reactions (antioxidants). The effects of bovine heart cardiolipin (BCL) and synthetic 1,1′,2,2′-tetraoleyl cardiolipin (TOCL) on the Cyt c peroxidase activity detected by luminol-enhanced chemiluminescence (CL) were studied. The CL amplitude substantially increased in the presence of TOCL and BCL in the ranges of the cardiolipin to Cyt c molar ratios from 0 to 30 and from 0 to 50, respectively, and insignificantly increased upon further increase in these ratios to 640: 1 and 320: 1. This dependence of the CL amplitude on the cardiolipin to protein ratio may have been accounted for by saturation of the protein surface with cardiolipin molecules reached at a certain molar ratio. The effects of the antioxidants rutin and dihydroquercetin (DHQ) on the peroxidase activity of Cyt c in combination with BCL was studied in the presence of the CL activator coumarine C-525 at a BCL to Cyt c molar ratio of 32: 1. In both cases, the peroxidase activity decreased as the antioxidant content of the system increased. A 50% inhibition of the reaction was observed at DHQ and rutin concentrations of 10 and 3 μM, respectively. It is supposed that the use of antioxidants will make it possible to control the formation of lipid radicals on membrane-bound Cyt c, which is the key stage of apoptosis.     

Effect of the luminol signal enhancer selection on the curve parameters of an immunoassay and the chemiluminescence intensity and kinetics

In the present study, three luminol signal enhancers {4-methoxyphenol, 4-hydroxybiphenyl and 4-(1H-pyrrol-1-yl)phenol} were utilized in the chemiluminescence (CL) substrate solution of horseradish peroxidase (HRP). The latter was applied in a heterogenous enzyme immunoassay that has been previously described. The employment of these molecules greatly affected important assay parameters, such as detection limit and the range of the calibration curve and the results were compared with those obtained from other two similar enhancers that have been described from our group. Practically, the use of a novel enhancer, even if this is a slightly changed 4-substituted phenol derivative, can affect assay properties so dramatically, one can assume that another substrate/enzyme system was applied. Furthermore, the use of different luminol signal enhancers in the luminol/HRP/H₂O₂ system affected not only the intensity of the obtained signal, which is well known, but also its kinetics. It was monitored that the stronger intensity was combined with a more rapid decrease of the CL signal.     

Enzymatic assay with detection by enhanced luminol chemiluminescence in a reversed micellar system: determination of l-amino acids and glucose

A detection system for hydrogen peroxide, i.e., luminol chemiluminescence (CL) in a hexadecyltrimethylammonium bromide (CTAB) reversed micellar system, was coupled to enzyme reactions. The use of CTAB reversed micellar medium allows one to conduct both the oxidase enzymatic and CL detection reactions simultaneously at mild pH (l-amino acid system, pH 8.7; glucose system, pH 8.5) in the absence of any co-oxidant or catalyst. Based on this result, simple and unique determinations of l-amino acids and glucose as substrates were developed. The calibration graph for a representative amino acid, l-phenylalanine, was linear in the concentration range 4.0×10^?6?200×10^?6M with a relative standard deviation of 5.78% (five determinations). The method established for l-phenylalanine was also applicable for the assay of fourteen other l-amino acids. The calibration graph for glucose was linear in the concentration range 5.4×10^??540×10^?6M with a relative standard deviation of 4.27% (eight determinations). This method was compared with a standard spectrophotometric method (hexokinase) and successfully applied to the determination of glucose in human serum.     

Application of multivariate curve resolution-alternating least squares (MCR-ALS) for resolving pyrogallol autoxidation in weakly alkaline aqueous solutions

Multivariate curve resolution — alternating least squares (MCR-ALS) has been applied to data collected from UV/Vis spectrophotometric analysis of the autoxidation process of pyrogallol in weakly alkaline aqueous solutions. The MCR-ALS analysis was able to explain the autoxidation kinetics of pyrogallol at pH 7.4 and 8.0, allowing deduction of the pure spectra and concentration changes of different species present throughout the entire process. The autoxidation process at pH 7.4 was found to follow a first-order reaction model, with formation of purpurogallin as the sole and terminal product. Changing the pH to 8.0 not only accelerated autoxidation of pyrogallol to purpurogallin but also introduced a further autoxidation of purpurogallin. At pH 8.0 the process fits a model of two consecutive first-order reactions. The first step is formation of purpurogallin, which reacts in a further autoxidation to form a yellow colored substance, most probably purpurogallin polymer.      

Alkaline phosphatase-labeled macromolecular probe for sensitive chemiluminescence detection of proteins on a solid-phase membrane

In the present study, we synthesized dextran (MW = ca. 2,000 kDa)-based macromolecular probes containing multiple molecules of alkaline phosphatase (ALP) as a signal-trigger enzyme and of biotin as an assembly mediator. The ALP and biotin molecules were covalently attached into the dextran backbone after the formation of aldehyde groups into the macromolecule by periodate oxidation. The synthesized probes contained 27–31 molecules of ALP in their macromolecules when 50-fold molar ratio of ALP to the dextran was used for the synthesis. These probes provided 14–20 times stronger chemiluminescence (CL) than that of the equimolar free ALP adsorbed on a nylon membrane. The velocity of the CL reaction of ALP-catalyzed adamantlyl-1,2-dioxetane substrate was improved from a slower emission (glow type) of CL to a faster one (flash type). The CL signal integrated for 2 min under strongly alkaline conditions (pH 13.0) was about ten times greater than that obtained by the conventional conditions (pH 9.5). Therefore, the synthesized macromolecular probe could be successfully utilized for the high-throughput CL detection of biotin-conjugated anti-rabbit IgG antibody with a lower detection limit of 880 amol per spot on the nylon membrane. This study provides analytical strategy for the rapid, convenient, and sensitive detection of target proteins in immunoassays.     

Influence of pH upon surface-enhanced enzyme-catalyzed luminol chemiluminescence at vicinity of nanoscale-corrugated gold and silver films

Abstract Au and Ag biochips were fabricated to investigate the influence of pH upon the chemiluminescence (CL) of luminol at vicinity of surface-adsorbed peroxidase. A nanoscaled-corrugation of the metal induces an enhancement of the luminol CL which is maximal in the pH range favoring peroxidase catalysis and greater for gold than for silver. This is the proof that, in the CL process, the reactions involving peroxidase are surface-enhanced near corrugated surfaces.     

Analytical use of a biochemical luminous membrane

Luminous membranes were prepared by immobilizing peroxidase (POD) to collagen matrix. The POD luminous membrane generated luninescence in the presence of luminol and H₂O₂, and the peroxide was determined in the concentration range 10-⁶-10-³ M by following luminescence emitted from the membrane. Glucose was determined using a luminous membrane in which POD and glucose oxidase (GOD) were coimmobilized. The luminous membranes appear to be feasible for the determination of enzyme substrates and enzyme activity.     

Ostensible enzyme promiscuity: alkene cleavage by peroxidases

Enzyme promiscuity is generally accepted as the ability of an enzyme to catalyse alternate chemical reactions besides the 'natural' one. In this paper peroxidases were shown to catalyse the cleavage of a C=C double bond adjacent to an aromatic moiety for selected substrates at the expense of molecular oxygen at an acidic pH. It was clearly shown that the reaction occurs due to the presence of the enzyme; furthermore, the reactivity was clearly linked to the hemin moiety of the peroxidase. Comparison of the transformations catalysed by peroxidase and by hemin chloride revealed that these two reactions proceed equally fast; additional experiments confirmed that the peptide backbone was not obligatory for the reaction and only a single functional group of the enzyme was required, namely in this case the prosthetic group (hemin). Consequently, we propose to define such a promiscuous activity as 'ostensible enzyme promiscuity'. Thus, we call an activity that is catalysed by an enzyme 'ostensible enzyme promiscuity' if the reactivity can be tracked back to a single catalytic site, which on its own can already perform the reaction equally well in the absence of the peptide backbone.     

Chemical dissolution of iron in aqueous solutions

By anodic oxidation of hydrogen on the Pt ring of a metal-disk-Pt-ring rotating electrode in aqueous acid (pH 0.5–3) sulfate solutions, it is shown that during the polarization of the metal disk hydrogen coevolves by two parallel reactions. One is the well known electrochemical charge transfer process, while the other one is a direct chemical reaction of the metal, i.e. iron, with water molecules from the electrolyte. This process was proposed a long time ago by Kolotyrkin and co-workers, but their experimental results were subjected to serious criticism which is taken care of in the present paper. The chemical reaction is potential- and pH-independent and, depending on the actual conditions during the corrosion processes (actual potential, pH, etc.), can be of greater or smaller importance in the overall process. The consequences of the existence of this direct chemical reaction of metal with water molecules (i.e. H₂O-induced corrosion or chemical corrosion) on pitting and stress corrosion cracking of metals is discussed. Dedicated to the ninetieth anniversary of Ya.M. Kolotyrkin’s birth. This article was submitted by the authors in English.     

Characterization of a micro spiral flow cell for chemiluminescence detection

A 5.5 μl spiral micro-flow cell, mounted in front of a photomultiplier, is made from Teflon capillary (75 cm×100 μm ID) with two inlets for the CL reagent and carrier buffer and a waste outlet. It allows the rapid mixing of CL reagent and analyte and simultaneous detection of the emitted light. Using a flow rate of 25 μl/min for a 0.4 mM luminol-8 μM hemin solution (pH 11.6) and 50 μl/min of carrier buffer (pH 11.6), the slight exponential calibration curve for the flow injection–chemiluminescence (FI–CL) determination of H₂O₂ is 2.5–10 μM and the detection limit is 1.5 μM. The detection limit achieved by using a spiral flow cell is 24 times lower than that obtained from a conventional FI system with a low dead volume tee mixer and a 12 μl flow cell in a HPLC fluorometer with the source lamp off. This luminol CL detection method is successfully applied to the enzymatic determination of -lactate by FI. The lactate sample is mixed with polyethylene glycol (PEG)-stabilized lactate oxidase (LO) enzyme and then injected into the buffered (pH 7.5) carrier stream for CL detection of the H₂O₂ product. Using the optimal conditions of reaction temperature set to 37.5 °C and flow rates of 45 μl/min for the CL reagent and 60 μl/min for the carrier buffer, the calibration range for lactate is 5–50 μM and the detection limit is 2.9 μM. This method is applied to the determination of -lactate in beer.     

Microfluidic device capable of sensing ultrafast chemiluminescence

Based on the principle of liquid core waveguide, a novel microfluidic device with micro-scale detection window capable of sensing flashlight emitted from rapid 1,1′-oxalyldi-4-methylimidazole (OD4MI) chemiluminescence (CL) reaction was fabricated. Light emitted from OD4MI CL reaction occurring in the micro-dimensional pentagonal detection window (length of each line segment: 900.0 μm, depth: 50.0 μm) of the microfluidic device with two inlets and one outlet was so bright that it was possible to take an image every 1/30 s at the optimal focusing distance (60 cm) using a commercial digital camera. Peaks obtained using a flow injection analysis (FIA) system with the micro-scale detection window and OD4MI CL detection show excellent resolution and reproducibility without any band-broadening observed in analytical devices having additional reaction channel(s) to measure light generated from slow CL reaction. Maximum height (H_max) and area (A) of peak, reproducibility and sensitivity observed in the FIA system with the microfluidic device and OD4MI CL detection depends on (1) the mole ratio between bis(2,4,6-trichlorophenyl) oxalate and 4-methyl imidazole yielding OD4MI, (2) the flow rate to mix OD4MI, H₂O₂ and 1-AP in the detection window of the microfluidic device, and (3) H₂O₂ concentration. We obtained linear calibration curves with wide dynamic ranges using H_max and A. The detection limit of 1-AP determined with H_max and A was as low as 0.05 fmole/injection (signal/background = 3.0).     

Flow-injection chemiluminescent determination of vanadium(IV) and total vanadium by means of catalysis on the periodate oxidation of purpurogallin

A flow-injection chemiluminescent (CL) method is proposed for the successive determination of nanogram levels of vanadium(IV) and total vanadium. The method is based on the catalytic effect of vanadium(IV) on the oxidation of purpurogallin by periodate to produce light emission at 4 °C. The presence of hydrogen carbonate enhanced the light emission arising from the vanadium(IV)-catalyzed reaction. Since vanadium(V) did not catalyze the CL reaction of purpurogallin, vanadium(V) was determined after being reduced to vanadium(IV) by using an on-line silver-reducing column. Calibration curves for vanadium(IV) and (V) were linear in the range 0.1–10 ng ml⁻¹ with sampling rate of about 50 h⁻¹. The limit of detection for signal-to-noise ratio of 2 was 0.05 ng ml⁻¹ and the relative standard deviations were 1.4 and 1.6% for ten determinations of 2.0 ng ml⁻¹ vanadium(IV) and (V), respectively. Interferences from metal ions could be eliminated by the use of O,O′-bis(2-aminoethyl)ethyleneglycol- N,N,N′,N′-tetraacetic acid and diphosphate as masking agents. The proposed method was successfully applied to the determination of vanadium(IV) and total vanadium in fresh water samples.     

Automated chemiluminescent dual-analyte immunoassay based on resolved immunosensing channels

A novel system of series-wound immunosensing channels (SWIC) was proposed for automated chemiluminescent (CL) dual-analyte immunoassay by immobilizing respectively different capture antibodies on the inner walls of series-wound glass channels. This system could use a single enzyme as label to perform multiplex immunoassay in one fluid way. Using α-fetoprotein (AFP) and carcinoembryonic antigen (CEA) as model analytes, the mixture including AFP, horseradish peroxidase (HRP)-labeled anti-AFP antibody, CEA and HRP-labeled anti-CEA antibody was introduced into the SWIC for carrying out the on-line incubation. Upon injection of CL substrate the CL signals from the two immunosensing channels were conveniently resolved and near-simultaneously collected with the aid of optical shutter. AFP and CEA could be rapidly assayed in the ranges of 1.0-100 and 1.0-80 ng/ml with detection limits of 0.41 and 0.39 ng/ml, respectively. The assay results of clinical serum samples were in an acceptable agreement with the reference values. This designed flow-through immunosensing system based on SWIC provided an automated, reusable, simple, sensitive and low-cost approach for multianalyte immunoassay.     

Optical Fiber Chemiluminescence Biosensor for Antioxidants Based on an Immobilized Luminol/Hematin Reagent Phase

ABSTRACT

A chemiluminescence (CL) biosensing system for antioxidants was developed based on luminol and hematin co-immobilized on a cellulose membrane disc. The concentration of the antioxidant was quantified through the measurement of the inhibition of the CL emitted when hydrogen peroxide was introduced into the reagent phase. The instrumentation employed in the measurement was a fabricated luminometer employing optical fibers and a UV-enhanced photodiode transducer. Under optimum conditions, linear calibration curves were obtained for antioxidant concentrations ranging from 1 × 10^-4 M to 0.10 M, with an average relative standard deviation of about 5%. The minimum detectable concentration was 100 μM, and the response time was less than 60 seconds. The sensor response correlated well (r = 0.9979) with the results of a standard colorimetric method for a specific antioxidant (propyl gallate). The sensor was used to assess the antioxidant capacity of water infusions prepared from the dried leaves of some Philippine medicinal plants.     

Controlled polymerization of ϵ-caprolactone -from macromolecules to microspheres

Pseudoanionic polymerization of ϵ-caprolactone (CL), initiated with dialkylaluminum alkoxides, was used for the tailored synthesis of poly(CL) with M̄_n ≤ 100 000 and M̄_w /M̄_n < 1. 20. Macromolecules with functional groups at one or at both ends were obtained in this way. Controlled polymerization of CL allowed to prepare poly(dodecyl acrylate)-g-poly(ϵ-caprolactone) (poly(DAC)-g-poly(CL)) with well defined poly(CL) grafts. These copolymers were used as the surface active agents for the direct synthesis of poly(CL) microspheres. The number average diameter (D̄_n ) of poly(CL) microspheres varied from 0.628 μm to 0.94 μm and the diameter polydispersity (D̄_v /D̄_n ) varied from 1.038 to 1.26, depending on the composition of poly(DAC)-g-poly(CL). Human serum albumin (HSA) and human gamma globulins (_γ G) were attached to the poly(CL) microspheres. The maximal surface concentrations of HSA and _γ G adsorbed onto the microspheres were equal to 9·10⁻⁴ g/m² and 2.0·10⁻³ g/m² respectively.     

Determination of medroxyprogesterone acetate residues by CE immunoassay with chemiluminescence detection

A rapid and simple method is developed for the determination of medroxyprogesterone acetate (MPA) by CE immunoassay with chemiluminescence (CL). This method is based on the competitive reactions between horseradish peroxidase (HRP)-labeled MPA (MPA-HRP) and free MPA with anti-MPA antiserum. The influencing factors on the electrophoresis and CL detection were studied completely and the optimal conditions of separation and determination were obtained. The linear range was 2.0-50 nmol/L and the LOD for MPA was 0.9 nmol/L. The present method was applied to the analysis of pork tissues.     

On-line chemiluminescence detection for isoelectric focusing of heme proteins on microchips

In this paper we present a sensitive chemiluminescence (CL) detection of heme proteins coupled with microchip IEF. The detection principle was based on the catalytic effects of the heme proteins on the CL reaction of luminol-H2O2 enhanced by para-iodophenol. The glass microchip and poly(dimethylsiloxane) (PDMS)/glass microchip for IEF were fabricated using micromachining technology in the laboratory. The modes of CL detection were investigated and two microchips (glass, PDMS/glass) were compared. Certain proteins, such as cytochrome c, myoglobin, and horseradish peroxidase, were focused by use of Pharmalyte pH 3-10 as ampholytes. Hydroxypropylmethylcellulose was added to the sample solution in order to easily reduce protein interactions with the channel wall as well as the EOF. The focused proteins were transported by salt mobilization to the CL detection window. Cytochrome c, myoglobin, and horseradish peroxidase were well separated within 10 min on a glass chip and the detection limits (S/N=3) were 1.2x10(-7), 1.6x10(-7), and 1.0x10(-10) M, respectively.     

Enzyme electrodes with substrate and co-enzyme amplification

The enzyme couples horseradish peroxidase/glucose dehydrogenase, glucose oxidase/glucose dehydrogenase, and cytochrome b₂/lactate dehydrogenase are applied in enzyme electrodes. Based on amplification by the recyclization reactions catalyzed by these two-enzyme systems, NADH, NAD⁺, glucose, lactate and pyruvate, are determined with 8–40-fold increased sensitivity compared to the unamplified reactions. Detection limits are 1.0 × 10^?6 M NADH, 1.2 × 10^?6 M NAD⁺, 8 × 10^?7 M glucose, and 3 × 10^?7 M lactate or pyruvate.     

Simultaneous detection of uric acid and glucose on a dual-enzyme chip using scanning electrochemical microscopy/scanning chemiluminescence microscopy

Scanning electrochemical microscopy (SECM) and scanning chemiluminescence microscopy (SCLM) were used for imaging an enzyme chip with spatially-addressed spots for glucose oxidase (GOD) and uricase microspots. For the SECM imaging, hydrogen peroxide generated from the GOD and/or uricase spots was directly oxidized at the tip microelectrode in a solution containing glucose and/or uric acid (electrochemical (EC) detection). For the SCLM imaging, a tapered glass capillary (i.d. of 1∼2 μm) filled with luminol and horseradish peroxidase (HRP) was used as the scanning probe for generating the chemiluminescence (CL). The inner solution was injected from the capillary tip at 78 pl s⁻¹ while scanning above the enzyme-immobilized chip. The CL generated when the capillary tip was scanned above the enzyme spots was detected using a photon-counter (CL detection). Two-dimensional mapping of the oxidation current and photon-counting intensity against the tip position affords images of which their contrast reflects the activity of the immobilized GOD and uricase. For both the EC and CL detections, the signal responses were plotted as a function of the glucose and uric acid concentrations in solution. The sensitivities for the EC and CL detection were found to be comparable.