Ultraviolet photolytic vapor generation from particulate ensembles for detection of malathion residues in aerosols

A method to selectively generate vapor signatures from malathion entrained within matrices of surface-impacted aerosol particles has been demonstrated. The method uses ultraviolet radiation (172 or 222 nm) from a continuous wave discharge lamp to photodissociate malathion molecules collected within and on surface-impacted particles, followed by detection via ion mobility spectrometry (IMS). Since surface heating does not occur, only those molecules whose photofragments exhibit high vapor pressure are introduced into the IMS instrument and then only those exhibiting high proton affinity are subsequently detected. This process produces less signal clutter than in pyrolysis-IMS, where the background aerosol is pyrolyzed along with the sample. Quantities of malathion as small as 50 ng could be detected when the malathion was entrained on a clean surface, and as small as 100 ng when co-entrained on a surface with much larger quantities of background aerosols such as diesel soot, road dust, Bacillus globigii, albumin, and cotton lint. This sensitivity indicates that, when combined with a particle collector as an effective pre-concentrator, detection of malathion aerosol concentrations of <0.01 mg/m³ will be possible. Since malathion can be viewed as a model compound, this technique is also extendable to the detection of organophosphate war chemicals.     

Comparison of the performance of three ion mobility spectrometers for measurement of biogenic amines

The performance of three different types of ion mobility spectrometer (IMS) devices: GDA2 with a radioactive ion source (Airsense, Germany), UV-IMS with a photo-ionization source (G.A.S. Germany) and VG-Test with a corona discharge source (3QBD, Israel) was studied. The gas-phase ion chemistry in the IMS devices affected the species formed and their measured reduced mobility values. The sensitivity and limit of detection for trimethylamine (TMA), putrescine and cadaverine were compared by continuous monitoring of a stream of air with a given concentration of the analyte and by measurement of headspace vapors of TMA in a sealed vial. Preprocessing of the mobility spectra and the effectiveness of multivariate curve resolution techniques (MCR-LASSO) improved the accuracy of the measurements by correcting baseline effects and adjusting for variations in drift time as well as enhancing the signal to noise ratio and deconvolution of the complex data matrix to their pure components. The limit of detection for measurement of the biogenic amines by the three IMS devices was between 0.1 and 1.2 ppm (for TMA with the VG-Test and GDA, respectively) and between 0.2 and 0.7 ppm for putrescine and cadaverine with all three devices. Considering the uncertainty in the LOD determination there is almost no statistically significant difference between the three devices although they differ in their operating temperature, ionization method, drift tube design and dopant chemistry. This finding may have general implications on the achievable performance of classic IMS devices.     

Fast detection of methyl tert-butyl ether from water using solid phase microextraction and ion mobility spectrometry

Methyl tert-butyl ether (MTBE) is commonly used as chemical additive to increase oxygen content and octane rating of reformulated gasoline. Despite its impact on enhancing cleaner combustion of gasoline, MTBE poses a threat to surface and ground water when gasoline is released into the environment. Methods for onsite analysis of MTBE in water samples are also needed. A less common technique for MTBE detection from water is ion mobility spectrometry (IMS). We describe a method for fast sampling and screening of MTBE from water by solid phase microextraction (SPME) and IMS. MTBE is adsorbed from the head space of a sample to the coating of SPME fiber. The interface containing a heated sample chamber, which couples SPME and IMS, was constructed and the SPME fiber was introduced into the sample chamber for thermal desorption and IMS detection of MTBE vapors. The demonstrated SPME-IMS method proved to be a straightforward method for the detection of trace quantities of MTBE from waters including surface and ground water. We determined the relative standard deviation of 8.3% and detection limit of 5 mg L⁻¹ for MTBE. Because of short sampling, desorption, and detection times, the described configuration of combined SPME and IMS is a feasible method for the detection of hazardous substances from environmental matrices.     

An NO+ reactant ion source for ion mobility spectrometry

The major reactant ion in conventional ion mobility spectrometry (IMS) is the hydronium ion, H₃O⁺ which is produced in the usual ionization sources such as corona discharge or radioactive sources. Using the hydronium reactant ion, mostly the analytes with proton affinity higher than that of water are ionized. A broader range of compounds can be detected by IMS if other alternative ionization channels, such as charge transfer from NO⁺, are employed. In this work we introduce a simple and novel method for producing NO⁺ as the major reactant ion in IMS. This was achieved by adding neutral NO to the corona discharge ionization source. The neutral NO was prepared via an additional discharge in an air stream, flowing into the corona discharge source. A curtain plate was mounted in front of the corona discharge to prevent the influence of the analyte on the production of NO⁺. Using this technique, the reactant ion could easily and quickly switch between the H₃O⁺ and NO⁺. The performance of the new source was evaluated by recording ion mobility spectra of test compounds with both H₃O⁺ and NO⁺ reactant ions.     

Highly selective determination of methylmercury with methylmercury-imprinted polymers

In this paper a new prototype of solid phase microextraction-ion mobility spectrometry (SPME-IMS) system was developed to effectively couple the extraction efficiency of SPME with the detection capability of IMS. The main component of this system was the transfer line/desorber, which was a low-thermal-mass (ca. 0.15 g) silicosteel coatings stainless steel tube. The transfer line/desorber was designed to rapidly desorb and transfer the analytes extracted by SPME to IMS. A custom-made temperature controller with a proportional-integral-differential (PID) was used to maintain the temperature of the transfer line/desorber stable and avoid overheating or oscillating. The low thermal mass of this interface allowed it to be rapidly heated and cooled with much less electrical power and could substantially reduce the demand for high capacity batteries. The operational characteristics of this system were demonstrated through the analysis of camphor vapour. The precision of reduced mobility and the peak amplitude of camphor were good (R.S.D. 0.62%, n = 10; R.S.D. 2.5%, n = 10, respectively). SPME-IMS system was also shown to be capable of on-site measurement by monitoring the biogenic volatile organic compounds (BVOCs) emitted from eucalyptus citriodora leaves. In addition, this system was applied to quantitation of diazepam and cocaine in aqueous solution. Limits of detection were 10 ng/mL for diazepam and 50 ng/mL for cocaine with the reported experimental conditions. This SPME-IMS system exhibits considerable promise as a robust, simple, rapid, energy-saving fieldable approach for on-site analysis of analytes in various matrix.     

Rapid analysis of captopril in human plasma and pharmaceutical preparations by headspace solid phase microextraction based on polypyrrole film coupled to ion mobility spectrometry

A rapid, simple, and sensitive headspace solid phase microextraction coupled to ion mobility spectrometry (HS-SPME-IMS) method is presented for analysis of the highly specific angiotensin-converting enzyme (ACE) inhibitor, captopril (CAP). Positive ion mobility spectra of CAP were acquired with an ion mobility spectrometer equipped with a corona discharge ionization source. Mass-to-mobility correlation equation was used to identify product ions. A dodecylsulfate-doped polypyrrole (PPy-DS) coating was used as a fiber for SPME. The results showed that PPy-DS based SPME fiber was suitable for successfully extracting CAP from human blood plasma and pharmaceutical samples. The HS-SPME-IMS method provided good repeatability (R.S.D.s < 4%) for aqueous and spiked plasma samples. The calibration graphs were linear in the range of 10-300 ng mL⁻¹ (R² > 0.99) and detection limits were 7.5 ng mL⁻¹ for aqueous and 6.3 ng mL⁻¹ for plasma blank samples. Finally, a standard addition calibration method was applied to HS-SPME-IMS technique for the analysis of blood plasma samples and tablets. Purpose method seemed to be suitable for the analysis of CAP in plasma samples as it is not time consuming (state total time from sample preparation to analysis), it required only small quantities of the sample, and no derivatization was required.     

Response of halogenated compounds in ion mobility spectrometry depending on their structural features

Ion mobility spectrometry (IMS) with handheld and transportable devices permits the sensitive detection of chlorinated compounds which are important in environmental monitoring. The ion mobility spectra in negative measuring modus mostly show one product ion peak [(H₂O)_nCl⁻] due to dissociative electron attachments. In this paper, we investigated relevant chlorinated compounds (R-Cl) where R represents allyl-, benzyl-, phenyl-, alkyl- and vinyl-groups. These groups cause differences in the R-Cl bond strength and differences in the cleavage of chlorine can therefore be expected. All chlorinated substances investigated provide the same product ion peak at 2.75 cm² Vs⁻¹ independent on the different C-Cl bond strength. However, distinct influences of structural features on the peak intensities of the (H₂O)_nCl⁻ product ion peak were established. Generally, increasing sensitivities were obtained in the order chlorobenzenes < vinyl- < allyl- < alkyl compounds < benzylchlorides. Sensitivities and limits of detection (LODs) of aromatic compounds depend on the nature and position of second substituent. Electron-withdrawing substituents (chlorine, fluorine, nitrile) enhance sensitivity while electron-repelling substituents decrease it. A dependence of sensitivity on the chain length or ring size can be observed for alkyl compounds. Additional influences of intramolecular interactions on the sensitivity were found for di-halogenated compounds. Therefore, the quantification of negative product ion peaks of chlorinated compounds requires a consideration of structural features of analytes.     

Headspace solid-phase microextraction using a dodecylsulfate-doped polypyrrole film coupled to ion mobility spectrometry for the simultaneous determination of atrazine and ametryn in soil and water samples

A simple and rapid headspace solid-phase microextraction (HS-SPME) based method is presented for the simultaneous determination of atrazine and ametryn in soil and water samples by ion mobility spectrometry (IMS). A dodecylsulfate-doped polypyrrole (PPy-DS), synthesized by electrochemical method, was applied as a laboratory-made fiber for SPME. The HS-SPME system was designed with a cooling device on the upper part of the sample vial and a circulating water bath for adjusting the sample temperature. The extraction properties of the fiber to spiked soil and water samples with atrazine and ametryn were examined, using a HS-SPME device and thermal desorption in injection port of IMS. Parameters affecting the extraction efficiency such as the volume of water added to the soil, pH effect, extraction time, extraction temperature, salt effect, desorption time, and desorption temperature were investigated. The HS-SPME-IMS method with PPy-DS fiber, provided good repeatability (RSDs < 10 %), simplicity, good sensitivity and short analysis times for spiked soil (200 ng g⁻¹) and water samples (100 and 200 ng mL⁻¹). The calibration graphs were linear in the range of 200-4000 ng g⁻¹ and 50-2800 ng mL⁻¹ for soil and water respectively (R² > 0.99). Detection limits for atrazine and ametryn were 37 ng g⁻¹ (soil) and 23 ng g⁻¹ (soil) and 15 ng mL⁻¹ (water) and 10 ng mL⁻¹ (water), respectively. To evaluate the accuracy of the proposed method, atrazine and ametryn in the three kinds of soils and two well water samples were determined. Finally, comparing the HS-SPME results for extraction and determination of selected triazines using PPy-DS fiber with the other methods in literature shows that the proposed method has comparable detection limits and RSDs and good linear ranges.     

Polypyrrole/montmorillonite nanocomposite as a new solid phase microextraction fiber combined with gas chromatography–corona discharge ion mobility spectrometry for the simultaneous determination of diazinon and fenthion organophosphorus pesticides

A novel solid phase microextraction (SPME) fiber was prepared and coupled with gas chromatography corona discharge ion mobility spectrometry (GC–CD–IMS) based on polypyrrole/montmorillonite nanocomposites for the simultaneous determination of diazinon and fenthion. The nanocomposite polymer was coated using a three-electrode electrochemical system and directly deposited on a Ni–Cr wire by applying a constant potential. The scanning electron microscopy images revealed that the new fiber exhibited a rather porous and homogenous surface. The thermal stability of the fabricated fiber was investigated by thermogravimetric analysis. The effects of different parameters influencing the extraction efficiency such as extraction temperature and time, salt addition, stirring rate, the amount of nanoclay, and desorption temperature were investigated and optimized. The method was exhaustively evaluated in terms of sensitivity, recovery, and reproducibility. The linearity ranges of 0.05–10 and 0.08–10 μg L⁻¹, and the detection limits of 0.020 and 0.035 μg L⁻¹ were obtained for diazinon and fenthion, respectively. The relative standard deviation values were calculated to be lower than 5% and 8% for intra-day and inter-day, respectively. Finally, the developed method was applied to determine the diazinon and fenthion (as model compounds) in cucumber, lettuce, apple, tap and river water samples. The satisfactory recoveries revealed the capability of the two-dimensional separation technique (retention time in GC and drift time in IMS) for the analysis of complex matrices extracted by SPME.     

Ionic liquid-based single drop microextraction and room-temperature gas chromatography for on-site ion mobility spectrometric analysis

The combination of ionic liquid-based headspace single drop microextraction (IL-HS-SDME) and room-temperature gas chromatography/ion mobility spectrometry (RTGC-IMS) is presented for the first time using the direct determination of trihalomethanes in waters as model analytical problem. The ionic liquid allows the transference of the analytes from the sample to the analytical system, at the same time that it provides an increase of the sensitivity and selectivity of the determination. An injection unit has been designed to permit the efficient volatilization of the analytes at room temperature and to avoid the entering of IL in the system. The direct combination allows the determination of the halocompounds in a rapid and simple way taking advance of their characteristic IMS spectra. The limits of the detection range between 0.1 ng mL⁻¹ (bromoform) and 0.9 ng mL⁻¹ (chloroform), the reproducibility of the system being better than 7.1% (RSD). The proposed coupling opens up a new horizon in IMS-based applications.     

Analysis of 2,4,6-trinitrotoluene, pentaerythritol tetranitrate and cyclo-1,3,5-trimethylene-2,4,6-trinitramine using negative corona discharge ion mobility spectrometry

In this study, the capability of negative corona discharge ion mobility spectrometry (IMS) for quantitative magnitude of several explosives including 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN) and cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX) has been evaluated for the first time. The total current obtained with the negative corona discharge was about 100 times larger than that of IMS based on ⁶³Ni, which results in a lower detection limit and a wider linear dynamic range. The detection limits for PETN, TNT and RDX were 8×10⁻¹¹, 7×10⁻¹¹ and 3×10⁻¹⁰ g, respectively. The calibration plots for these explosives showed linear dynamic ranges of about four orders of magnitude.     

Determination of ochratoxin A in maize bread samples by LC with fluorescence detection

Ochratoxin A (OTA) is a secondary fungal metabolite produced by several moulds, mainly by Aspergillus ochraceus, A. carbonarius, A. niger and by Penicillium verrucosum. The present work shows the results of comparative studies using different procedures for the analysis of OTA in maize bread samples. The studied analytical methods involved extraction with different volumes of PBS/methanol, different extraction apparatus, and clean-up through immunoaffinity columns. The separation and identification were carried out by high-performance liquid chromatography with fluorescence detection. The optimized method for analysis of OTA in maize bread involved extraction with PBS:methanol (50:50), and clean-up with IAC column. The limit of quantification was 0.033 ng g⁻¹. Recoveries ranged from 87% to 102% for fortifications at 2.000 and 0.500 ng g⁻¹, respectively, within-day R.S.D. of 1.4% and 4.7%. The proposed method was applied to 15 samples and the presence of OTA was found in nine samples at concentrations ranging from nd to 2.650 ng g⁻¹.     

Direct detection of trimethylamine in meat food products using ion mobility spectrometry

Biogenic amines are degradation products generated by bacteria in meat products. These amines can indicate bacterial contamination or have a carcinogenic effect to humans consuming spoiled meats; therefore, their rapid detection is essential. Trimethylamine (TMA) is a good target for the detection of biogenic amines because its volatility. TMA was directly detected in meat food products using ion mobility spectrometry (IMS). TMA concentrations were measured in chicken meat juice for a quantitative evaluation of the meat decaying process. The lowest detected TMA concentration in chicken juice was 0.6 ± 0.2 ng and the lowest detected signal for TMA in a standard aqueous solution was 0.6 ng. IMS data were processed using partial least squares (PLS) and Fuzzy rule-building expert system (FuRES). Using these two chemometric methods, trimethylamine concentrations of different days of meat spoilage can be separated, indicating the decaying of meat products. Comparing the two methods, FuRES provided a better classification of different days of meat spoilage.     

Rapid preseparation of interferences for ion mobility spectrometry

Two new approaches to reduce false positive interferences commonly observed with explosives and drugs detection in the field were reported for ion mobility spectrometry (IMS). One of the approaches involved the rapid preseparation of potential interferences prior to detection by IMS. Firstly, it was found that the introduction of a short column packed with adsorption packing material before an IMS could help to reduce the false positive rates. Secondly, the retention time at which the most intense response occurred over the analysis time period could be utilized to separate false positive responses from target analytes with the same drift times. Rapid preseparation of potential interferences provided a greater degree of confidence for the detection (in less than 30 s) of drugs, explosives and chemical warfare agents (CWAs). Detection limits as low as 10 pg of TNT with a sensitivity of 12 A g⁻¹ were reported. Successful development of this technique may lead to the construction of a simple interface fitted with a short column of adsorption packing material to enhance either initial separation or to hold-back interferences mixed with explosive and drug responses in the field.     

Corona discharge ion mobility spectrometry for the determination of theophylline and guaifenesin in human serum

This paper describes the determination of theophylline and guaifenesin in human serum using ion mobility spectrometry with positive corona discharge as source ionization. The optimization of parameters that could influence ion mobility spectrometry was investigated. Under optimum conditions (Temperature; injection: 220 and oven: 175 °C, Flow rate; carrier: 300 and drift: 600 mL min^?1, Voltage; corona: 2300 and drift: 7000 V, pulse width: 100 μs), calibration curves were linear in the ranges of 2 to120 and 6 to 120 ng for theophylline and guaifenesin, respectively. The relative standard deviation (n?=?10) was below 12 %. The detection limits were found to be 0.1 ng for theophylline and 0.5 ng for guaifenesin. The recovery results for the theophylline and guaifenesin determination in human serum was about 80 % that indicate the proposed method can be applied for the two drugs analysis in real sample. Furthermore, the proposed method has been evaluated in the simultaneous determination of the two drugs.     

Determination of terpenes in humid ambient air using ultraviolet ion mobility spectrometry

Atmospheric humidity causes the major problem using ion mobility spectrometers (IMS) under ambient conditions. Significant changes of the spectra are decreasing sensitivity as well as selectivity. Therefore, the influence of humidity on the IMS signal was investigated in case of direct introduction of the analyte into the ionisation chamber and in case of pre-separation by help of a multi-capillary column (MCC). For direct analyte introduction, a significant decrease of the total number of ions in the range of 28-42% with increasing relative humidity was found. Simultaneously additional peaks in the spectra were formed, thus complicating the identification of the analytes. In case of pre-separation of the analyte, the spectra do not change with increasing relative humidity, due to the successive appearance of the analyte and the water molecules in the ionisation chamber. Detection limits were found in the range of 5 μg/m³ (about 1 ppbv) for selected terpenes and—with pre-separation—independent on relative humidity of the analyte. Without pre-separation, detection limits are in the same range for dry air as carrier gas but in the range of 200-600 μg/m³ when relative humidity reaches 100%. Thus, MCC-UV ion mobility spectrometry is optimally capable for the detection of trace substances in ambient air (e.g. indoor air quality control, process control, odour detection) without further elaborate treatment of the carrier gas containing the analyte and independent on relative humidity.     

Separation of sarcosine and L-alanine isomers using corona discharge ion mobility spectrometry

The capability of corona discharge ion mobility spectrometry (CD-IMS) for separation and quantification of sarcosine and L-alanine isomers has been evaluated for the first time. Although these two compounds have the same mass and m/z values in mass spectrometer, ion mobility spectrometry was able to separate and determine them. Variables including carrier gas flow rate, injection and cell temperatures were optimized. The reduced mobilities (K ₀) of sarcosine and L-alanine were 1.96 and 1.83, respectively, based on the reduced mobility of nicotinamide. At the optimized conditions the detection limit of sarcosine and L-alanine were 0.7 and 0.9 μg/mL, respectively. The relative standard deviation (RSD) was found to be 6%. Furthermore, a sample injection port of a gas chromatograph was also modified to introduce solvent-free samples into the IMS.     

Evaporation of ionic liquids at atmospheric pressure: study by ion mobility spectrometry

A conventional ion mobility spectrometry (IMS) was used to study atmospheric pressure evaporation of seven pure imidazolium and pyrrolidinium ionic liquids (ILs) with [Tf₂N], [PF₆], [BF₄] and [fap] anions. The positive drift time spectra of the as-received samples measured at 220 °C exhibited close similarity; the peak at reduced mobility K₀ = 1.99 cm² V⁻¹ s⁻¹ was a dominant spectral pattern of imidazolium-based ILs. With an assumption that ILs vapor consists mainly of neutral ion pairs, which generate the parent cations in the reactant section of the detector, and using the reference data on the electrical mobility of ILs cations and clusters, this peak was attributed to the parent cation [emim]. Despite visible change in color of the majority of ILs after the heating at 220 °C for 5 h, essential distinctions between spectra of the as-received and heated samples were not observed. In negative mode, pronounced peaks were registered only for ILs with [fap] anion.     

Determination of MTBE in drinking water using corona discharge ion mobility spectrometry

Methyl tertiary-butyl ether (MTBE) is an organic compound which is used as a gasoline additive. Contamination of ground and surface water can occur due to large scale use of MTBE and its high solubility in water. According to United State Environmental Protection Agency (USEPA), MTBE is a possible human carcinogen at high doses and its detection and measurement in the water is important as concerned about human health. In this work, ion mobility spectrometry (IMS) equipped with a corona discharge ionization source was used for determination of MTBE in drinking water. Both pure and aqueous solutions of MTBE were studied and their ion mobility spectra were obtained at different temperatures. Using a calibration curve for detection of MTBE in drinking water, a detection limit (LOD) of 1 mg/L was obtained by IMS. This work proved that, IMS with corona discharge can be used for fast and direct detection of MTBE in water sample without any sample preparation.     

Ultrasensitive one-step rapid detection of ochratoxin A by the folding-based electrochemical aptasensor

A one-step electrochemical aptasensor using the thiol- and methylene blue- (MB-) dual-labeled aptamer modified gold electrode for determination of ochratoxin A (OTA) was presented in this research. The aptamer against OTA was covalently immobilized on the surface of the electrode by the self-assembly effect and used as recognition probes for OTA detection by the binding induced folding of the aptamer. Under the optimal conditions, the developed electrochemical aptasensor demonstrated a wide linear range from 0.1 pg mL⁻¹ to 1000 pg mL⁻¹ with the limit of detection (LOD) of 0.095 pg mL⁻¹, which was an extraordinary sensitivity compared with other common methods for OTA detection. Moreover, as a practical application, this proposed electrochemical aptasensor was used to monitor the OTA level in red wine samples without any special pretreatment and with satisfactory results obtained. Study results showed that this electrochemical aptasensor could be a potential useful platform for on-site OTA measurement in real complex samples.