On the interfacial chemistry of aryl diazonium compounds in polymer science

This review emphasises the role of aryl diazonium compounds as a new class of coupling agents for grafting polymer thin layers onto carbon, diamond, metals, metal oxides, alloys, semi-conductors, ceramics, and polymers. Physical and chemical methods are first reported for anchoring aryl layers to the surfaces, then the review concentrates on the modification of the above substrates by thin polymer films via a range of the “grafting from” and “grafting onto” strategies. Some applications are described which highlight the important role that diazonium salts will continue to play in the near future in the polymer and surface sciences.     

Ferroelectric Materials by the Sol-Gel Method

The sol-gel method is ideally suitable for the preparation of ferroelectric thin films such as LiNbO₃, BaTiO₃, KNbO₃ and PZT. The preparation and properties of polycrystalline, amorphous and single crystal films of these ferroelectric oxides are summarized. The origin of “amorphous ferroelectricity” is discussed. Single crystal KNbO₃ films have been successfully fabricated into planar waveguides and their ability to convert infrared laser into green light demonstrated.     

AFM,ellipsometry, XPS and TEM on ultra-thin oxide/polymer nanocomposite layers in organic thin film transistors

Here we report on the fabrication and characterization of ultra-thin nanocomposite layers used as gate dielectric in low-voltage and high-performance flexible organic thin film transistors (oTFTs). Reactive sputtered zirconia layers were deposited with low thermal exposure of the substrate and the resulting porous oxide films with high leakage currents were spin-coated with an additional layer of poly-α-methylstyrene (PαMS). After this treatment a strong improvement of the oTFT performance could be observed; leakage currents could be eliminated almost completely. In ellipsometric studies a higher refractive index of the ZrO₂/PαMS layers compared to the “as sputtered” zirconia films could be detected without a significant enhancement of the film thickness. Atomic force microscopy (AFM) measurements of the surface topography clearly showed a surface smoothing after the PαMS coating. Further studies with X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) also indicated that the polymer definitely did not form an extra layer. The polymer chains rather (self-)assemble in the nano-scaled interspaces of the porous oxide film giving an oxide–polymer “nanocomposite” with a high oxide filling grade resulting in high dielectric constants larger than 15. The dielectric strength of more than 1 MV cm⁻¹ is in good accordance with the polymer-filled interspaces.     

Control of ionic transport through gated single conical nanopores

Control of ionic transport through nanoporous systems is a topic of scientific interest for the ability to create new devices that are applicable for ions and molecules in water solutions. We show the preparation of an ionic transistor based on single conical nanopores in polymer films with an insulated gold thin film “gate.” By changing the electric potential applied to the “gate,” the current through the device can be changed from the rectifying behavior of a typical conical nanopore to the almost linear behavior seen in cylindrical nanopores. The mechanism for this change in transport behavior is thought to be the enhancement of concentration polarization induced by the gate. Figure   Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Solid state structural aspects of electrochemically prepared poly (p -phenylene) thin films – crystalline order and spherulite morphology

The electrochemical polymerization of benzene via the microemulsion approach yields highly crystalline and anisotropic “spherulitic” polyparaphenylene (PPP) thin films. The crystalline order and the origin of spherulite morphology are discussed. Received: 29 July 1997 / Accepted: 27 October 1997     

A new SERS-active sandwich structure

We report surface-enhanced Raman scattering (SERS) from a “sandwich” structure of two silver layers, in which a thin film of activated carbon is embedded. The first silver layer is prepared by electroless deposition on a non-conductive substrate, while the second one is electrodeposited on the adsorbed carbon powder. This “sandwich” does not only yield stable SERS signals from the carbon but also a strong additional enhancement (compared to SERS from simple carbon/silver or silver/carbon structures), stemming from a coupling of the two silver layers. The “sandwich” structure should be widely applicable since its preparation is very simple.Paper presented at the “Jahrestagung der Fachgruppe Angewandte Electrochemie der Gesellschaft Deutscher Chemiker, Düsseldorf, 11.–14.06.2005.”     

Multivariate analysis of HT/GC-(IT)MS chromatographic profiles of triacylglycerol for classification of olive oil varieties

The ability of multivariate analysis methods such as hierarchical cluster analysis, principal component analysis and partial least squares-discriminant analysis (PLS-DA) to achieve olive oil classification based on the olive fruit varieties from their triacylglycerols profile, have been investigated. The variations in the raw chromatographic data sets of 56 olive oil samples were studied by high-temperature gas chromatography with (ion trap) mass spectrometry detection. The olive oil samples were of four different categories (“extra-virgin olive oil”, “virgin olive oil”, “olive oil” and “olive-pomace” oil), and for the “extra-virgin” category, six different well-identified olive oil varieties (“hojiblanca”, “manzanilla”, “picual”, “cornicabra”, “arbequina” and “frantoio”) and some blends of unidentified varieties. Moreover, by pre-processing methods of chemometric (to linearise the response of the variables) such as peak-shifting, baseline (weighted least squares) and mean centering, it was possible to improve the model and grouping between different varieties of olive oils. By using the first three principal components, it was possible to account for 79.50% of the information on the original data. The fitted PLS-DA model succeeded in classifying the samples. Correct classification rates were assessed by cross-validation.     

From GUM to alternative methods for measurement uncertainty evaluation

Since the advent of the Guide to the expression of Uncertainty in Measurement (GUM) in 1995 laying the principles of uncertainty evaluation numerous projects have been carried out to develop alternative practical methods that are easier to implement namely when it is impossible to model the measurement process for technical or economical aspects. In this paper, the author presents the recent evolution of measurement uncertainty evaluation methods. The evaluation of measurement uncertainty can be presented according to two axes based on intralaboratory and interlaboratory approaches. The intralaboratory approach includes “the modelling approach” (application of the procedure described in section 8 of the GUM, known as GUM uncertainty framework) and “the single laboratory validation approach”. The interlaboratory approaches are based on collaborative studies and they are respectively named “interlaboratory validation approach” and “proficiency testing approach”.     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

Erbium and ytterbium co-doped SiO<Subscript>2</Subscript>:GeO<Subscript>2</Subscript> planar waveguide prepared by the sol–gel route using an alternative precursor

The sol–gel method combined with a spin-coating technique has been successfully applied for the preparation of rare-earth doped silica:germania films used for the fabrication of erbium-doped waveguide amplifiers (EDWA), presenting several advantages over other methods for the preparation of thin films. As with other methods, the sol–gel route also shows some drawbacks, such as cracks related to the thickness of silica films and high hydrolysis rate of certain precursors such as germanium alkoxides. This article describes the preparation and optical characterization of erbium and ytterbium co-doped SiO₂:GeO₂ crack-free thick films prepared by the sol–gel route combined with a spin-coating technique using a chemically stable non-aqueous germanium oxide solution as an alternative precursor. The non-crystalline films obtained are planar waveguides exhibiting a single mode at 1,550 nm with an average thickness of 3.9 μm presenting low percentages of porosity evaluated by the Lorentz–Lorenz Effective Medium Approximation, and low stress, according to the refractive index values measured in both transversal electric and magnetic polarizations. Weakly confining core layers (0.3% < Δn < 0.75%) were obtained according to the refractive index difference between the core and buffer layers, suggesting that low-loss coupling EDWA may be obtained. The life time of the erbium ⁴I_13/2 metastable state was measured as a function of erbium concentration in different systems and based on these values it is possible to infer that the hydroxyl group was reduced and the formation of rare-earth clusters was avoided.     

Electrochemical preparation of poly(<Emphasis Type="Italic">p</Emphasis>-phenylene) thin films

We report the electrochemical preparation of poly(p-phenylene) (PPP) thin films with a polymerization degree of approximately 20 using biphenyl as starting material. The PPP films are prepared directly on a tin oxide electrode, presenting a positive charge carrier mobility of 5×10⁻⁷ cm² V⁻¹ s⁻¹.     

Effect of sol temperature on the structure,morphology, optical and photoluminescence properties of nanocrystalline zirconia thin films

Transparent nanocrystalline zirconia thin films were prepared by sol–gel dip coating technique using Zirconium oxychloride octahydrate as source material on quartz substrates, keeping the sol at room temperature (SET I) and 60 °C (SET II). X-ray diffraction (XRD) pattern shows the formation of mixed phase [tetragonal (T) + monoclinic (M)] in SET I and a pure tetragonal phase in SET II ZrO₂ thin films annealed at 400 °C. Phase transformation from tetragonal to monoclinic was achieved in SET II film annealed at 500 °C. Atomic force microscopy analysis reveals lower rms roughness and skewness in SET II film annealed at 500 °C indicating better optical quality. The transmittance spectra gives a higher average transmittance >85% (UV–VIS region) in SET II films. Optical spectra indicate that the ZrO₂ films contain direct—band transitions. The sub- band in the monoclinic ZrO₂ films introduced interstitial O⁻defect states above the top of the valance band. The energy bandgap increased (5.57–5.74 eV) in SET I films and decreased (5.74–5.62 eV) in SET II films, with annealing temperature. This is associated with the variations in grain sizes. Photoluminescence (PL) spectra give intense band at 384 and 396 nm in SET I and SET II films, respectively. A twofold increase in the PL intensity is observed in SET II film. The “Red” shift of SET I films and “Blue” shift of SET II films with annealing temperature, originates from the change of stress of the film due to lattice distortions.     

Titanium-supported nickel-copper oxide catalysts for oxidation of carbon(II) oxide

Nickel-copper compositions for catalytic oxidation of carbon(II) oxide to carbon(IV) oxide were prepared by impregnation of oxide films on titanium surface, obtained by plasma electrolytic oxidation followed by annealing. Plasma electrolysis oxide coatings with a layer thickness of 5 to 50 μm were generated using different electrolytes. The compositions were studied by X-ray powder diffraction, X-ray spectral analysis, and electron microscopy, and moisture absorption of the initial plasma electrolytic structures was estimated. A linear correlation was found between the overall concentration of nickel and copper (4 to 25 mol %) in the surface layer of ∼2–5-μm compositions and their catalytic activity. The overall concentration of nickel and copper was found to increase in parallel with the moisture absorption of plasma electrolytic oxidation coatings. Nickel-copper compositions based on plasma electrolytic oxidation coatings generated in a silicate electrolyte displayed the best catalytic, mechanical, and adhesion properties.     

New serinolic amino-<Emphasis Type="Italic">s</Emphasis>-triazines by chemoselective amination of cyanuric chloride and their (pro)diastereomerism in restricted rotational phenomena

The highly chemoselective preparation of new elaborated N-unsymmetrically substituted chlorodiamino-s-triazines and melamines, seen as building-blocks for iterative synthesis, is reported. It consisted of amination of cyanuric chloride with commercial C-2-substituted 2-aminopropane-1,3-diols (“serinols”), playing the role as “open-chain” unit and enantiopure (1S,2S)-2-amino-1-(4-nitrophenyl)propane-1,3-diols (“p-nitrophenylserinols”) based amino-1,3-dioxanes (“closed-chain” unit). Issued from the restricted rotation about C(s-triazine)-N(exocyclic) partial double bonds, seen as axes of (pro)diastereomerism, a global four-component rotational equilibrium involving the title compounds is discussed based on DFT computation and (VT) NMR data. Depending on π-deficiency of the s-triazine core, an (un)synchronised deblocking of the generated rotational diastereomers was observed. They are discussed as influence of intra-vs. intermolecular NH...OH (dynamic) interactions occurring in the “open-chain” unit and the anancomeric, axial vs. equatorial, amino-anchorage of the “closed-chain” unit.      

Sub-micron wear measurement using activities under the free handling limit

In the present work we demonstrate the development of a thin layer activation (TLA) method to be able to measure micrometer wear or less by using radioactive tracing. In order to activate very swallow depths we decreased the bombarding energy to the “linear” region of the cross-section curve. The disadvantage of the method is that the wear curve will be “linear” near to the surface instead of “constant” as is the case with the usual (high energy) TLA. The advantage is that the activity of the sample will be much lower and it is concentrated in the swallower studied depth. The other possible method is irradiation under small angle (15 to 30° or even grazing incidence), which also causes a near-surface concentration of the activity produced. Both methods are demonstrated with the most suitable nuclear reactions and some commonly used industrial materials.     

Crystallization Behavior of Sol-Gel Derived Films by Self-Seeding Process

We propose the novel preparation method, Self-seeding Process, based on the following concept for low temperature crystallization of oxide films. Introduction of desirable inhomogeneity should give lowering of a crystallization temperature through heterogeneous nucleation accompanied with reduced activation energy. We carried out inspection of the above concept through use of PZT films. PZT gel films with the desirable inhomogeneity of microstructure were prepared, and their crystallization behaviors was examined. The PZT film was successfully crystallized at 500°C by the self-seeding process. The single phase (001) oriented PZT film with 0.55 m in thickness was obtained at 550°C for 5 min. The self-seeding process by microstructure control is efficient for the low temperature process of the oxide thin film.     

Overview: The Potential of silanes for chromate replacement in metal finishing industries

Trialkoxysilanes (or silanes) have emerged as a very promising alternative for chromates in metal finishing industries. Compared to the conventional chromating processes, the major merits of silane-based surface treatments include: eco-compliance, easy-control processing, comparable corrosion protection of metals as well as paint adhesion to a variety of topcoats. In this overview paper, we report the recent status of silane studies including results of corrosion performance tests, the mechanism of corrosion protection of metals by silanes and the themal stabilities of silane films. We also address the new fields that we are beginning to explore such as nano-structured silane films, “self-healing” silane films, and “super-primers”.     

纳米二氧化钛粉体及薄膜制备的研究进展

本文对近几年有关纳米二氧化钛粉体及薄膜的制备研究进行综述。重点介绍及评述了以无机钛盐和有机钛盐为前驱体制备纳米二氧化钛粉体及利用自组装方法制备二氧钛薄膜的最新研究成果。对今后研究工作的趋势进行了探讨。     

Spectroscopic,electrocatalytic, and photoelectrochemical characteristics of mixed-ligand bis(β-dicarbonylato) phthalocyanine complexes of zirconium(IV) and hafnium(IV)

The electronic absorption (EAS) and fluorescence spectra and electrocatalytic and photoelectrochemical characteristics of mixed-ligand complexes of zirconium(IV) and hafnium(IV) based on phthalocyanines in solutions and in thin films were investigated. It was established that a significant bathochromic shift of the Q band and redistribution of the intensities in the absorption bands are observed in the electronic absorption spectra. It was shown that films of the synthesized compounds are promising for use as photosensitizers and electrochemical sensors for oxygen in solution. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 3, pp. 133–137, May–June, 2008.     

Correlation between structural and optical properties of TiO<Subscript>2</Subscript>:ZnO thin films prepared by sol–gel method

We have studied structural and optical properties of thin films of TiO₂, doped with 5% ZnO and deposited on glass substrate (by the sol–gel method). Dip-coated thin films have been examined at different annealing temperatures (350–450 °C) and for various layer thicknesses (89–289 nm). Refractive index, porosity and energy band gap were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.97–2.44, the porosity is in the range of 0.07–0.46 and the energy band gap is in the range of 3.32–3.43. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZnO, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 20.23 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range of 8.61–29.48 nm.