功能梯度压电圆板轴对称自由振动问题精确解

将功能梯度压电圆板的位移变量和电势变量写为分离变量的形式，由压电动力学平衡方程导出以位移、电势及其一阶导数为状态变量的状态方程，考虑周边固支接地的边界条件，导出了求解功能梯度压电圆板自振频率精确解的方程。将方程退化至一般的非梯度纯弹性圆板的形式，求解其自振频率，得到的结果与相应的理论解完全吻合，从而验证了本文方法的正确性。更进一步地对梯度函数沿板厚以指数形式变化的功能梯度压电圆板的自振频率进行了计算，并得到了梯度化对板自振频率的影响规律。     

柱面受温度载荷的轴对称横观各向同性压电热弹性圆柱的精化理论

将精化理论的研究方法推广到轴对称横观各向同性压电热弹性圆柱的研究中,利用压电热弹性问题的轴对称通解以及准调和函数的Bessel算子函数表示方法,获得了该圆柱在柱面受温度载荷作用下的精确耦合场;当柱面受到随轴向Z增大而逐渐减小的轴对称量纲为一的温度载荷时,绘制出圆柱在半径r分别为0.2、0.4、0.6、0.8、1.0时的位移分量、电势、温度增量沿轴向z的分布。结果表明:圆柱在同一高度的情况下,径向位移和轴向位移随半径增大而增大,电势的绝对值也随半径的增大而增大,而温度增量随半径的变化则不明显。此外,本文还通过算例验证了该精化理论应用的正确性。     

压电材料中切口/接头端部平面电弹性场奇异性有限元分析

为了对平面载荷作用下压电材料中切口或接头端部附近电弹性场奇异性问题进行分析，首先以应力平衡方程、Maxwell方程和和边界条件为基础，得到一种求解压电材料特征问题的弱式方程；其次，假定楔形切口或接头端部附近单元内位移和电势沿径向分布为指数形式，而周向方向分布则采用泡函数插值，将其代入弱式方程，建立一种只需对楔形切口或接头端部附近周边进行离散的一维简单有限元方法．压电材料的极化轴可以是任意方向．利用该有限元模型讨论了楔形切口角度、极化轴方向和边界条件对奇性场的影响．通过和其它特定情况下的现有解相比，证实了该文有限元数值方法的有效性，而且精度很高．     

压电陶瓷中圆币形裂纹在横向剪力下的机－电耦合行为

以弹性位移分量和电势函数为基本未知量时，横观各向同性压电介质三维问题的场方程可化为四个联立的二阶线性偏微分方程组，本文导出了用四个调和函数表示位移分量及电势函数的表达式，即得到了该场方程的势函数通解，作为通解的应用举例，文中求解了圆币形裂纹受横向剪切作用的问题，得到了裂尖附近应力场及电位移场的解析表达式，结果表明，在横向剪切载荷下圆币形裂纹的尖端场及应力、电位移强度因子均具有明显的机－电耦合性质，而应力和电位移分量在裂尖仍具有－１／２的奇异性。     

压电陶瓷中圆币形裂纹在横向剪力下的机—电耦合行为

以弹性位移分量和电热函数基本未知量时，横观各向同性压电介质三维问题的场方程可化为四个联立的二阶线性偏微分方程组，本文导出了用四个调和函数表示位移分量及电势函数的表达式，即得到了该场方程的势函数能通解，作为通解的应用举例，文中求解了圆币形裂纹受横向剪切载荷下圆币形裂纹的尖端场及应力、电位移强度因子均具有明显的机－电耦合性质，而应力和电位移分量在裂尖仍具有－１／２的奇异性。     

反对称斜交叠层板双向弯曲问题的横向基理论解

研究反对称斜交叠层板的双向弯曲问题。根据横向基理论，在厚度方向，给出了三个方向位移沿厚度的分布规律；在面内方向，采用升阶谱位移函数；然后，应用最小势能原理导出叠层板的静力控制方程。通过对多种层数和铺层角的层板力学响应计算分析表明：在典型位置的应力分布，本文解与三维弹性解符合很好，并有较好的收敛性。     

压电材料中椭圆片状裂纹问题精确解的一种方法

在线性压电陶瓷本构关系和裂纹边界绝缘的框架下,用超奇异积分方程的方法对椭圆类片状裂纹问题进行了重新研究．超奇异积分方程中的未知位移间断和电势间断近似地表示为基本密度函数与多项式之积,其中基本密度函数反映了椭圆片状裂纹前沿电弹性场的奇异性,而多项式在均布载荷作用下可用一个常数来表达．引入椭球坐标系后,得到了均布载荷作用下未知位移间断和电势间断的解析解．使用这些解析解和电弹性场强度的定义,得到了裂纹前沿Ⅰ型、Ⅱ型和Ⅲ型应力强度因子以及电位移强度因子的精确表达式．法向均布载荷作用下的结果与现有精确解完全一致,切向均布载荷作用下的结果则尚未见有其它报道．     

基于修正高精度广义胞元法的复合材料细观力学分析

高精度广义胞元法是多尺度分析复合材料模量和微观应力应变场的有效方法之一．然而，由于位移插值函数中缺少二次耦合项，很大程度上影响了复合材料局部应力、应变场，特别是剪切场的计算精度．本文通过引入二次方向耦合项，提出了一种修正的高精度广义胞元法插值函数．在施加周期性边界条件、平均应力和平均位移连续性条件后，可以确定位移插值函数中的系数．通过对多相复合材料弹性模量和局部场分析，并且与有限元分析和实验测量结果比较，验证了修正高精度广义胞元法的准确性．与高精度广义胞元相比，本文提出的修正高精度广义胞元法在不需要引入额外未知变量，不影响计算效率的前提下，对复合材料的局部应力场计算得更加准确．     

横观各向同性三维热弹性力学通解及其势理论法

通过引入两个位移函数，对用位移表达的运动平衡方程作了简化．利用算子理论，严格地导出了横观各向同性非耦合热弹性动力学问题的通解．对于静力学问题，通解的形式可进一步简化成用4个准调和函数来表示．具体考察了横观各向同性体内平面裂纹上下表面有对称分布温度作用的问题，推广了势理论方法，导出了一个积分方程和一个微分-积分方程．针对币状裂纹表面受均布温度作用情形，给出了具体的解。     

压电层合圆杆中的几何非线性波

利用有限变形理论,导出了描述压电层合杆中几何非线性波的传播方程.在端部作用有限振幅位移函数的边界条件下,用逐步近似法对位移函数进行了假设,推导出了一维压电杆中位移函数与电势函数之间的关系式,并应用变动参数法求解了变换得到的非齐次波动方程,得到了位移和电势的响应.数值分析表明:初始频率的改变对位移和电势的非线性特性影响不大;而初始振幅的增加会使非线性波形畸变特性明显增强.     

Wave propagation in elastic laminates using a second order microstructure theory

A generalization of the simpler microstructure theory developed earlier for elastic laminates by Sun, Achenbach and Herrmann is used to analyze steady state plane wave propagation. This new version incorporates higher-order thickness variations in the displacement functions and includes restrictions on both displacement and stress at the laminate interfaces.To assess the potential of a second-order microstructure theory for accurate modeling of mechanical processes in laminates, dispersion results and especially mode shape data for both displacements and stresses are obtained and compared to corresponding solutions obtained by the theory of elasticity. The comparisons indicate that while dispersion results may be nearly identical, extremely significant differences may be observed in the mode shapes.     

Nonlinear dynamic response of piezoelastic laminated plates considering interfacial damage effects

This paper presents a nonlinear model for cross-ply piezoelastic laminated plates containing the damage effect of the intralayer materials and interlaminar interfaces. The model is based on the general six-degrees-of-freedom plate theory, the discontinuity of displacement, and electric potential on the interfaces are depicted by three shape functions, which are formulated according to solutions about three equilibrium equations and conservation of charge. By using the Hamilton variation principle, the three-dimensional nonlinear dynamic equations of piezoelastic laminated plates with damage are presented. Then using the finite difference method and the Newmark scheme, an analytical solution is presented. In numerical examples, the effects of different damage models, damage evolution, amplitude and frequency of electric loads on the nonlinear dynamic response of piezoelectric laminated plate with interfacial imperfections are investigated.     

A coupled zigzag theory for the dynamics of piezoelectric hybrid cross-ply plates

A recently developed coupled third-order zigzag theory for the statics of piezoelectric hybrid cross-ply plates is extended to dynamics. The theory combines a third-order zigzag approximation for the in-plane displacements and a sub-layerwise linear approximation for the electric potential, considering all components of the electric field. The nonuniform variation of the transverse displacement due to the piezoelectric field is accounted for. The conditions for the absence of shear traction at the top and bottom surfaces and continuity of transverse shear stresses in the presence of electromechanical loading are satisfied exactly, thereby reducing the number of displacement variables to five, which is the same as in a first- or third-order equivalent single-layer theory. The governing equations of motion are derived from the extended Hamilton's principle. The theory is assessed by comparing the Navier solutions for the free and forced harmonic vibration response of simply supported plates with the exact three-dimensional piezoelasticity solutions. Comparisons for hybrid test, composite and sandwich plates establish that the present theory is quite accurate for the dynamic response of moderately thick plates.     

压电介质二维边界积分方程中的基本解

由于压电介质的变形－电场耦合效应及压电响应的各向异性，使解析求解压电介质问题的工作变量十分复杂，若采用边界元数值方法求解，必须具备积分方程中的基本解，本文根据电磁场方程及连续介质力学的耦合性质论层出了二维无限域中分别在单位力及单位电荷载作用下的位移场，电势场、应力场和电位移场的解，从而确立了边界积分方程中所必需的八个基本解。     

Exact static analysis of a rotating piezoelectric spherical shell

This paper gives an exact analysis of a rotating piezoelectric spherical shell with arbitrary thickness. At first, three displacement functions are introduced to simplify the basic equations of a spherically isotropic, piezoelectric medium. By expanding the displacement functions as well as the electric potential in terms of spherical harmonics, the basic equations of equilibrium are converted to an uncoupled Euler type, second order ordinary differential equation and a coupled system of three second order ordinary differential equations. A general solution to the homogeneous equations of equilibrium is then derived. The static analysis of a rotating spherical shell is then performed and numerical example is presented. The project supported by the National Natural Science Foundation of China, the Zhejiang Provincial Natural Science Foundation, and the Japanese Committee of Culture, Education and Science.     

Penny-shaped crack in transversely isotropic piezoelectric materials

Using a method of potential functions introduced successively to integrate the field equations of three-dimensional problems for transversely isotropic piezoelectric materials, we obtain the so-called general solution in which the displacement components and electric potential functions are represented by a singular function satisfying some special partial differential equations of 6th order. In order to analyse the mechanical-electric coupling behaviour of penny-shaped crack for above materials, another form of the general solution is obtained under cylindrical coordinate system by introducing three quasi-harmonic functions into the general equations obtained above. It is shown that both the two forms of the general solutions are complete. Furthermore, the mechanical-electric coupling behaviour of penny-shaped crack in transversely isotropic piezoelectric media is analysed under axisymmetric tensile loading case, and the crack-tip stress field and electric displacement field are obtained. The results show that the stress and the electric displacement components near the crack tip have (r ^−1/2) singularity. The project supported by the Natural Science Foundation of Shaanxi Province, China     

Indentation of a compressible soft electroactive half-space: Some theoretical aspects

We theoretically study the indentation response of a compressible soft electroactive material by a rigid punch. The half-space material is assumed to be initially subjected to a finite deformation and an electric biasing field. By adopting the linearized theory for incremental fields, which is established on the basis of a general nonlinear theory for electroelasticity, the appropriate equations governing the perturbed infinitesimal elastic and electric fields are derived particularly when the material is subjected to a uniform equibiaxial stretch and a uniform electric displacement. A general solution to the governing equations is presented, which is concisely expressed in terms of four quasi-harmonic functions. By adopting the potential theory method, exact contact solutions for three common perfectly conducting rigid indenters of flat-ended circular, conical and spherical geometries can be derived, and some explicit relations that are of practical importance are outlined.     

压电弹性层合板静力机耦合特性的解析解

应用经典权壳理论和压电理论对层合板结构进行简化。对四边简支压电层合板在不同电学边界条件下,包括四边电学开路和电学短路。上下表面受外电压及无外加电压作用,进行分析,求得了电势和挠度的解析表达式,给出了压电层和基体的挠度、电势分布图。     

板桁结构考虑局部屈曲空间计算的横向条带板段单元法

用有限个横向条带法构造了板桁组合结构板段考虑局部屈曲的空间位移模式。基于三维连续体的虚功增量方程,导出了横向条带板段单元的ＵＬ列式,并考虑了板段单元位形变化的影响。此计算方法自由度少,计算精度高,能用于大型板桁结构的几何非线性分析。文末计算了广东西江桥板桁组合结构模型梁,计算结果与实测结果吻合较好。     

压电、压磁材料球对称问题的通解

研究压电、压磁材料在球坐标系下,不计体力、体电荷和体电流的情况下,由平衡方程、梯度方程、压电和压磁的本构方程导出应力、应变、位移、电位移、电场强度、电位势、磁感强度和磁位势各未知量的通解．考虑不同的边界条件,将其通解应用到应力、电学短路以及位移、电学开路和磁场分布的边界条件中,得到不同边界条件下问题的解。