Optimisation of 40 Gb/s wavelength converters based on four-wave mixing in a semiconductor optical amplifier

The optimum operating powers and wavelengths for a 40 Gb/s wavelength converter based on four-wave mixing in a semiconductor optical amplifier are inferred from experimental results. From these measurements, some general rules of thumb are derived for this kind of devices. Generally, the optimum signal power should be 10 dB lower than the pump power (−16 dB conversion efficiency) whereas the wavelength separation between the signal and the pump carrier should not be lower than about four times the signal bitrate (1.3 nm for 40 Gb/s RZ signals).     

Stimulated Brillouin scattering limited intensity-dependent four-wave mixing between pump and signal in a non-zero dispersion shifted fiber

The intensity-dependent four-wave mixing (FWM) efficiency is derived by the nonlinear Schrodinger equations including the self phase modulation and cross phase modulation between the two Fabry–Perot modes of a pump and a single-wavelength signal. The maximum FWM for mixing the pump with signal in non-zero dispersion shifted fiber is explained as the minimum phase mismatch for FWM due to equal group delay for the pump and signal. It was also found that the experimental measurements for the generated FWM power are limited by the stimulated Brillouin scattering (SBS) threshold. Under the SBS threshold, the experimental results are still coincided well with the theoretical calculations of the FWM generated power ratio to have the difference of 0.12 dB for the input signal power of 12 mW.     

Spectral inversion with no wavelength shift based on four-wave mixing with orthogonal pump beams

Generation of phase-conjugate light with no wavelength shift that utilizes four-wave mixing (FWM) with two orthogonal pump beams is discussed. Owing to the polarization properties of nondegenerate FWM, phase-conjugate light generated at the original signal wavelength can be obtained. An experiment using dispersion-shifted fiber as an optical nonlinear medium confirms the proposed scheme.     

Measurement of nonlinear coefficient of a highly nonlinear fiber based on peak four-wave mixing signal generation conditions

We introduce a new measurement method of the nonlinear coefficient (NC) of a highly nonlinear fiber based on a four-wave mixing (FWM) technique. The NC along with the fiber's zero-dispersion wavelength (ZDW) was determined from the precise measurement of the pump power dependent optimum pump frequency for peak FWM signal generation conditions. The measurement errors of the NC and ZDW values determined with this method were less than 4.6% and 0.051 nm, respectively.     

Performance analysis for an all-optical wavelength converter using four-wave mixing (FWM) in a single mode fiber

An analytical approach is presented to determine the performance of a tunable wavelength converter based on four wave mixing (FWM) in a single mode fiber (SMF) with two pump lasers. The analysis is carried out for an intensity modulated (IM) signal taking into considerations the effects of spectral broadening due to FWM and laser phase noise. The results evaluated at a bit rate of 10 Gb/s show that the signal power is substantially higher at lower values of wavelength separation. For example, for input powers of 10 mW each, wavelength separation of 4 nm between the pump-2 and the input signal, the output converted power is found to be –10 dBm corresponding to wavelength separation of 2 nm between pump-1 and converter signal. The corresponding crosstalk power is found to be –25 dBm at a channel separation of 3 times bit rate.     

Polarization insensitive wavelength multicasting of DPSK signal using four-wave mixing in a birefringent photonic crystal fiber

We demonstrate polarization-insensitive wavelength multicasting of differential phase-shift keying (DPSK) signal based on four-wave mixing (FWM) in a highly nonlinear, birefringent photonic crystal fiber (PCF). The 10-Gbit/s RZ-DPSK input signal is copied to 8 wavelength channels through FWM with three optical pumps. The pump wavelengths are unequally spaced to avoid undesirable crosstalk from pump-to-pump beatings. The dependence of conversion efficiency on input signal polarization is suppressed by exploiting the PCF birefringence together with control of the pump polarizations. All pump polarizations are aligned at 45 degrees to the principal axes of the PCF. Open eyes and error-free results are obtained in all the 8 multicast channels for polarization-scrambled RZ-DPSK input signal.     

FDTD simulation of wavelength conversion of ultrashort pulses utilizing intersubband absorption in AlGaN/GaN quantum wells

The four-wave mixing (FWM) characteristics of 500-fs pulses in nonlinear optical waveguides utilizing the saturation of the intersubband absorption at 1.55 μm in nitride multiple quantum wells are calculated by a one-dimensional finite-difference time-domain (FDTD) method combined with three-level rate equations describing the intersubband carrier dynamics. Efficiency for a 100-nm wavelength conversion in a 160-μm waveguide is predicted to be higher than 3% both for up- and down-conversions. The extinction ratio is higher than 20 dB. As for the short-pulse application, however, the conversion efficiency is strongly dependent on the phase difference between the pump and signal pulses, especially when the efficiency is high. This causes ambiguity in the output power. Therefore, the cross-loss-modulation (XLM) converter is preferable to the FWM converter for OTDM application. The FWM converters are considered to be applicable to simultaneous conversion of WDM signals.     

A Novel Method for Wavelength Conversion with Dual-pump Four-wave Mixing in a Semiconductor Optical Amplifier

Using a semiconductor-fiber ring laser, a novel method for the all optical wavelength conversion based on dual-pump four-wave mixing (FWM) in a semiconductor optical amplifier (SOA) is demonstrated. For the input signal with different wavelengths, only one external pump is needed. This scheme can simplify the dual-pump FWM in SOA and has nearly constant conversion efficiency and signal-to-noise ratio (SNR) over 50nm range of wavelength shifts.     

A Novel Method for Wavelength Conversion with Dual-pump Four-wave Mixing in a Semiconductor Optical Amplifier

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　ＩｎｔｈｅＷＤＭｎｅｔｗｏｒｋ ,ｔｈｅｄｅｓｉｒａｂｌｅｆｅａｔｕｒｅｓｏｆａｎａｌｌ ｏｐｔｉｃａｌｗａｖｅｌｅｎｇｔｈｃｏｎｖｅｒｔｅｒｉｎｃｌｕｄｅｐｏｌａｒｉｚａｔｉｏｎｉｎｓｅｎｓｉｔｉｖｉｔｙ ,ｔｒａｎｓｐａｒｅｎｃｅｔｏｍｏｄｕｌａｔｉｏｎｆｏｒｍａｔａｎｄｂｉｔ ｒａｔｅ ,ｆｕｌｌｔｕｎａｂｉｌｉｔｙ ,ａｃｃｅｐｔａｂｌｅｏｕｔｐｕｔＳＮＲｏｖｅｒｔｈｅｅｎｔｉｒｅｒａｎｇｅｏｆｔｈｅｗａｖｅｌｅｎｇｔｈｓｕｓｅｄｉｎｔｈｅｎｅｔｗｏｒｋ[1] .Ｗａｖｅ…     

Efficiency and Output Power Evaluation of a Wavelength Converter Based on FWM in a Single Mode Fiber

A frequency domain analysis is presented to determine the performance characteristics of a tunable alloptical wavelength converter using four-wave mixing (FWM) in a single mode fiber (SMF) around the zero dispersion wavelength using two pump lasers. The output converted signal power as well as efficiency evaluated at a bit rate of 10 Gb/s show that the signal power is substantially higher at lower values of wavelength separation.     

基于光子晶体光纤中多抽运四波混频效应的新型光层组播技术

光层组播是未来透明光子网络中一项重要的全光信号处理功能,提出并实验证实了一种基于色散平坦高非线性光子晶体光纤中多抽运四波混频效应的光层组播方法,将一束信号光与两束连续抽运光同时输入高非线性光子晶体光纤中,通过多抽运四波混频过程,产生四个携带该数据信息的闲频光,从而实现了单一信号的四信道光层组播功能,组播信道波长在35.2 nm范围可调谐,组播信道最大间距4.4 THz,最大转换效率-22 dB,最优Q因子为5.3,该方法的特点在于基于光纤中的四波混频效应工作,因而具有对调制格式和比特率透明的 关键词： 光层组播 多抽运四波混频 光子晶体光纤     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

All-optical continuously tunable delay with a high linear-chirp-rate fiber Bragg grating based on four-wave mixing in a highly-nonlinear photonic crystal fiber

A scheme for hi-fi all-optical continuously tunable delay is proposed. The signal wavelength is converted to a desired idler wavelength and converted back after being delayed by a high linear-chirp-rate (HLCR) fiber Bragg grating (FBG) based on four-wave mixing (FWM) in a highly-nonlinear photonic crystal fiber (HN-PCF). In our experiment, 400 ps (more than 8 full width of half maximum, FWHM) tunable delay is achieved for a 10 GHz clock pulse with relative pulse width broaden ratio (RPWBR) of 2.08%. The power penalty is only 0.3 dB at 10⁻⁹ BER for a 10 Gb/s 2³¹−1 pseudo random bit sequence (PRBS) data.     

Multichannel wavelength multicasting for two QPSK signals based on FWM in SOA

We experimentally demonstrate multichannel wavelength multicasting for two nonreturn-to-zero quadrature phase-shift keying(NRZ-QPSK) channels based on four-wave mixing(FWM) in semiconductor optical amplifier(SOA). Through the interaction with the two pumps in SOA, the input two 25 Gb/s NRZ-QPSK channels are successfully simultaneously multicast to five and two new wavelengths, respectively. All the multicast channels are with a power penalty less than 2.5 d B at a bit error rate(BER) of 10-3. A characterization of the system performance using conversion efficiency and BER as figures-of-merit in terms of pump and signal powers is also presented. The results indicate that the pump and signal powers can be optimized to eliminate the introduced deleterious nonlinear components. The wavelengths of the two NRZ-QPSK channels and the two pumps need to be specified to avoid the crosstalk induced by high-order FWM.     

Erbium doped fiber ring laser for optical wavelength conversion

We experimentally investigate the gain saturation effect of a piece of 8 m long Erbium doped fiber (EDF), we introduce a theoretical model for the EDF ring loop, and our simulation results show very good cross-gain modulation (XGM) and wavelength conversion. We also experimentally investigate the XGM in an EDF ring loop system. Based on the study of the XGM in the EDF ring loop system, a wavelength conversion is designed with the EDF ring loop system. The EDF ring loop systems as a wavelength conversion is experimentally demonstrated by converting a sinusoidal modulated optical signal at wavelength of 1551 nm to an optical signal at wavelength of 1553.3 nm.     

A bandwidth-efficient channel allocation scheme for mitigating FWM in ultra-dense WDM-PON

In this paper, we investigate four-wave mixing (FWM) effects in the ultra-dense wavelength division multiplexing passive optical network (UDWDM-PON) system and propose an efficient channel allocation scheme to mitigate the FWM impact. This scheme is formed by grouping signal channels into several blocks with different channel spacing. Through numerical analysis and simulations, our proposed scheme is verified to be able to reduce the FWM effects and have higher bandwidth efficiency than the traditional unequal channel allocation scheme. The simulation results also demonstrate that our proposed scheme can achieve nearly 4 dB increases in optical power budget of the UDWDM-PON systems at the BER of 1e−3, in comparison with the equal spaced channel scheme.     

基于光子晶体光纤中四波混频效应的单到双非归零到归零码型转换

归零(RZ)码与非归零(NRZ)码是波分复用和时分复用系统中广泛采用的两种码型, 全光NRZ到RZ码型转换能完成从波分复用到时分复用的网络接口功能, 是未来透明光子网络中一项重要的全光信号处理技术. 提出并实验证实了一种基于色散平坦高非线性光子晶体光纤中四波混频效应的单到双NRZ到RZ码型转换方法, 将一束信号光与同步时钟脉冲同时输入色散平坦高非线性光子晶体光纤中, 通过四波混频过程, 产生两个携带该数据信息的闲频光, 从而实现了单到双的NRZ到RZ码型转换功能, 码型转换器工作波长在193 nm范围可调谐, 最大转换效率为-21 dB, 最优消光比和品质因子分别为11.9 dB和7.2. 该方法的特点在于基于光纤中的四波混频效应工作, 因而具有对调制格式和比特率透明的优点, 同时, 光子晶体光纤特有的高非线与色散平坦性, 既避免了使用传统光纤需要较长的长度, 又避免了波长设置不灵活的弊端, 并具备可进一步增加带宽的能力, 且在码型转换的同时, 实现了波长转换, 完成了双通道波长组播功能. 整个系统为全光纤设计, 结构简单, 性能可靠, 并易于与现有的光纤通信系统相容, 对促进超高速大容量光子网络的发展具有重要意义. 关键词： 码型转换 四波混频 光子晶体光纤     

All-optical wavelength multicasting based on cascaded four-wave mixing with a single pump in highly nonlinear fibers

We theoretically present and experimentally demonstrate all-optical wavelength multicasting based on cascaded four-wave mixing (FWM) in highly nonlinear fibers only using a single pump. The cascaded FWM effect is analyzed based on the sum amplitude method, which overcomes the limitation of the number of analyzed idlers, and the performance of the wavelength multicasting is evaluated. By using a continuous wave pump and a pulse train as the signal, multiple-order idlers are experimentally generated and the patterns of 6 multicasting channels are measured. Regardless of the dynamic region of the tunable filter, this method has the potential to realize more multicasting channels, especially when higher pump and signal powers are used.     

Boost up of four wave mixing signal in semiconductor optical amplifier for 40 Gb/s optical frequency conversion

The 40 Gb/s optical frequency converter for non-return to zero differential phase shift keying (NRZ-DPSK) signal by using four wave mixing in semiconductor optical amplifier (SOA) have achieved sucessfully. The optimized signal-to-pump ratio for NRZ-DPSK by using optimized SOA structure with enhanced FWM effect is also evaluated. The optimum signal-to-pump ratio is 12 dB and 10 dB with Q factor penalty of 0.685 dB and 0.663 dB. The dependence of four wave mixing efficiency and converted signal power on signal input power is studied and it is evaluated that four wave mixing efficiency decreases with increase in the input power. The impact of pump power, signal-to-pump ratio, and SOA parameters with Q factor penalty for 40 Gb/s has been illustrated. It has shown that converted signal power increases up to the saturation power of semiconductor optical amplifier, then decreases. It is observed that for the optimum pump power, OSNR of converted signal varies little with signal input power.     

Multiple, polarization diverse, idler wave generation in fibers from competing four-wave mixing processes

We report on a theoretical and experimental characterization of polarization-dependent four-wave mixing processes in highly nonlinear optical fibers. Two or three idler waves at different polarizations are experimentally generated in an optical fiber from the propagation of two wavelength-detuned, orthogonally-polarized pumps and a signal. Each idler wave results from a different four-wave mixing process involving the signal and one or both pumps. Orthogonally-polarized idler waves are demultiplexed in a polarization beam splitter with a cross-polarization suppression of over 17 dB. The parametric process equations for this system are analytically solved and the efficiencies of the competing processes analyzed for the small pump detunings and identical pump powers. This experimental setup can be used in telecommunication systems for producing and selectively rerouting various copies of a data signal.