Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Investigations on order and width of RZ super Gaussian pulse in different WDM systems at 40 Gb/s using dispersion compensating fibers

In optical wavelength division multiplexed (WDM) systems the dispersion management is a key issue. In optical systems a lot of research is going on to reduce dispersion by selecting proper dispersion compensating techniques and proper modulation format for input data. One way to reduce dispersion is by using dispersion compensating fibers in the WDM systems. This paper analyzes the use of RZ super Gaussian pulse inputs for different WDM systems i.e. for conventional, dense and ultra dense WDM systems employing dispersion compensating fibers. The pulse width and the order of the RZ super Gaussian pulse was varied to evaluate the performance at 40 Gb/s. The experiment showed that to get minimum BER, pulse width of 7.5 ps and 10 ps along with third-order RZ super Gaussian pulse were found suitable and recommended to be used.     

Performance analysis of NRZ, RZ, CRZ and CSRZ data formats in 10 Gb/s optical soliton transmission link under the impact of chirp and TOD

This paper presents the performance analysis of non-return-to-zero (NRZ), return-to-zero (RZ), chirped return-to-zero (CRZ) and carrier suppressed return-to-zero (CSRZ) data formats in optical soliton transmission link under the impact of chirp and third-order dispersion (TOD). The performance of these data formats has been analyzed on the basis of certain performance metrics, viz, bit error rate (BER), Q² (dB), OSNR, eye opening, etc. It has been reported here that the performance of CRZ and CSRZ modulation format is better as compared to NRZ and RZ in a soliton transmission link. Further, CSRZ modulation format has been found to deliver optimum performance on the basis of performance evaluation metrics reported in this paper. In case of NRZ and CSRZ, comparatively narrow power spectrum has been observed. Best eye opening, highest value of Q² (dB) of 18 dB and lowest value of BER of the order of 10⁻¹⁶ has been reported in case of CSRZ among the considered data formats. The results have been obtained by varying noise figure from 3.0 to 9.0. No considerable effect of noise was observed. It was observed that at very narrow and ultra short pulse width, OSNR value suffers heavily and reduced to even negative values in dB, thus inducing a high degree of OSNR power penalty. The results were obtained by varying chirp factor from −0.6 to +0.6. Negative chirp resulted in improved OSNR as compared to positive chirp. RZ data format yielded a broader optical spectrum, comparatively low spectral efficiency and poor OSNR thus it was found that RZ format is not suitable for optical soliton transmission under the impact of chirp and TOD.     

Performance improvement for N × 80-Gb/s WDM transmission link with optimized alternate polarization

In this paper, it is shown that at a high bit rate of 80-Gb/s alternate polarization of adjacent bits in a Wavelength Division Multiplexed (WDM) transmission link improves the system performance in terms of improved Q factor and minimum bit error rate (BER). Alternate Polarization Return to Zero (al-PRZ) further suppresses the non-linear effects at higher power levels of 25 dBm per channel and also improves the transmission length to 640 km for a N × 80-Gb/s WDM system and hence results in an improvement of BER to 10⁻²⁰.     

Simulation of high capacity 40 Gb/s long haul DWDM system using different modulation formats and dispersion compensation schemes in the presence of Kerr's effect

In this paper, simulative analysis of 40 Gb/s long haul (500-2000 km) DWDM system with ultra high capacity upto 1.28 Tb/s has been carried out for carrier-suppressed return-to-zero (CSRZ), duobinary return-to-zero (DRZ) and modified duobinary return-to-zero (MDRZ) modulation formats. The DWDM system has been analyzed for the pre, post and symmetrical dispersion compensation schemes for 16 Channels with 25 GHz channel spacing in order to find the optimum modulation format for a high bit rate optical transmission system. The effect of variation in input power and transmission distances is observed in terms of Q value and eye opening for various formats. It is found that symmetrical compensation is superior to pre and post dispersion compensation schemes. It has also been observed that the performance of DWDM system is severely limited by the four-wave mixing (FWM) effect and is determined that MDRZ format seems to be the best choice for the transmission distance beyond 1550 km despite slightly more complex transmitter and receiver configuration. Further, symmetrical compensation scheme has been investigated for 32×40 Gb/s MDRZ format for faithful transmission over 1450 km.     

High spectral-efficiency 100Gbit/s transmission using DRZ,DQPSK, and PoISK three dimension orthogonal modulation

We propose and demonstrate a new 4-bit/symbol optical data format based on simultaneously modulating dark return-to-zero (DRZ), differential quadrature phase-shift keying (DQPSK) and polarization-shift-keying (PoISK) for 100Gbit/s applications. Through numerical simulation, we show the differential tolerance of the three dimension modulation format toward polarization-mode dispersion (PMD) and chromatic dispersion. The receiver sensitivities of three different combined modulation formats, with those of DRZ, DQPSK and PoISK, are compared respectively, while extinction ratio of DRZ is changed. The proposed three dimension orthogonal modulation format has a more compact spectrum and is more tolerant to phase noise compared with DQPSK for 100Gbit/s transmission.     

Simulative analysis of co-existing 2.5 G/10 G asymmetric XG-PON system using RZ and NRZ data formats

In this paper, a fiber optic communication system has been employed using co-existing 10 G/2.5 G asymmetric gigabit passive optical network (XG-PON) architecture. In this system, bidirectional optical fiber has been used for upstream and downstream data transmission. The system performance has been investigated for non-return-to-zero (NRZ) and return-to-zero (RZ) data formats operating at varying bit rates by varying the length of the fiber for analyzing the feasibility of this co-existence. The results have been compared for NRZ and RZ formats for upstream and downstream data in terms of Q value and eye opening. It is observed that RZ modulation format is superior as compared to conventional NRZ format and the faithful transmission of signal has been carried up to 90 km at 1577 nm for downstream and 140 km at 1270 nm for upstream.     

The analysis of the error statistics in a 5 × 40 Gbit/s fibre link with hybrid amplification

We quantify the error statistics and patterning effects in a 5 × 40 Gbit/s WDM RZ-OOK SMF/DCF fibre link using hybrid Raman/EDFA amplification. By extensive use of a numerical model, we determine how the error statistics change with the transmission distance. This knowledge is used as a basis for a constrained coding technique in order to improve the transmission error rate. We propose an adaptive constrained code for mitigation of the patterning effects and demonstrate that this approach can substantially reduce the bit error rate (BER) even for very large values of the channel BER (BER > 10^− 1). The proposed technique can be used in combination with forward error correction schemes (FEC) to extend the range of channel BERs that an FEC scheme is effective over.     

2.50 Gbit/s optical CDMA over FSO communication system

Optical CDMA over FSO communication system is very effective to provide high data rate transmission with very low bit error rate and low amount of multiple access interference. In this paper, we have presented optical CDMA over FSO communication system to the range of 8000 m. The simulative results reveal that the transmission distance is limited mainly by the multi-access interference (MAI) which arises when there are number of users in the system because of the fact that one user data becomes noisy for all other users in the channel.     

40 Gb/s all-optical logic NOR and OR gates using a semiconductor optical amplifier: Experimental demonstration and theoretical analysis

We experimentally and theoretically demonstrate 40 Gb/s all-optical logic NOR and OR gates based on a semiconductor optical amplifier (SOA) and a blue shifted optical bandpass filter (OBF). Two kinds of data formats are discussed, namely return-to-zero (RZ) format and nonreturn-to-zero (NRZ) format. The logic NOR and OR functions of RZ format are realized at the OBF detuning of −0.22 nm and −0.44 nm, respectively. The logic NOR function of NRZ format is realized at the OBF detuning of −0.24 nm. The simulation is in good agreement with the experimental results when the linewidth enhancement factor is 5.5. The simulation also shows that the SOA with large linewidth enhancement factor is preferred to achieve NOR and OR functions with good performance. The input data signal is of good pulsewidth-tolerance for NOR function, whereas not for OR function. The high Q factor could be obtained at narrow pulses injection.     

Numerical analysis and system optimization for 100 Gbit/s carrier Ethernet serial modulation formats

The performance of various modulation schemes for 100 Gbit/s single-channel serial transmission is investigated by means of numerical simulations. Different ASK and PSK modulation formats are compared in terms of total system reach for a 10⁻⁹ BER requirement. RZ-DQPSK format with a 1920 km reach, without FEC and without the support of additional Raman amplification, outperforms all the other schemes including 10 × 10 Gbit/s NRZ DWDM inverse multiplexing.     

Generation, detection and characterization of optical minimum shift keying data format

This paper presents the detailed principle on the generation and detection of optical minimum shift keying (MSK) format for high-speed and high spectral efficiency WDM systems. 10.7 Gb/s optical MSK data is successfully generated by experiment using the proposed scheme. The results show that optical MSK signal exhibits very compact optical spectrum, which is promising for high spectral efficiency WDM applications. Simulation results on dispersion and nonlinear tolerance comparison confirm that MSK signal has better dispersion tolerance and nonlinear tolerance compared with 50% duty cycle return-to-zero differential phase shift keying (RZ-DPSK) and 50% duty cycle RZ on-off-keying (RZ-OOK) formats.     

Performance comparison between 160 Gb/s WDM and TDM systems

The performances of 160 Gb/s time-division multiplexing (TDM) and 4 × 40 Gb/s wavelength-division multiplexing (WDM) signals are comparatively studied in the nonzero-dispersion shifted fibers (NZDSFs). TDM format is superior to WDM, and with the increase of distance, this advantage is enhanced. In the case of adopting the dispersion managed soliton transmission and dispersion flattened fibers (DFFs) technique, the Q values of both formats change little when the channel space varies. So, TDM technique is applicable to the dense and very long haul transmissions. Only by utilizing the conventional loss and dispersion compensation schemes (NZDSFs + DCFs + EDFAs), the available transmission distance of dense WDM signals reaches 1000 km, and for TDM format, it even extends to 2000 km. Both systems have the analogue characteristics: a higher pulse power benefits system's working; ASE noise is the dominant impact factor of system performance; both format's system performances are improved for the case of less channel number; the channel space and duty cycle of return zero pulse have little effect on Q; the impact of duty cycle relates to the filter bandwidths, XPM induced sidebands and pulse broadening effect; the influence of channel space is determined by the walk-off effect.     

Analysis of 2.5 Gbit/s GPON downlink optical-receiver performance

In the gigabit-capable passive optical network (GPON) optical communication system, the selection of fiber and system performance-analysis is the key links for the realization of system function. Especially the characteristic budget and parameter setting of downlink receiver are topped the list. The analysis of receiver power penalty can reduce the influence on receiver sensitivity and bit error rate (BER) that caused by waveguide dispersion and pulse widening. This article will simulate the performance of GPON downlink receiver, then analyze typical characteristics such as Four Wave Mixing (FWM), Erbium-Doped Fiber Amplifier (EDFA), system eye pattern and Q factor and so on, so as to validate the feasibility of the optical downlink.     

Optical 3R regeneration of 40 Gbit/s degraded data signals

A 40 Gbit/s optical 3R regenerator is proposed and demonstrated. The 3R regenerator consists of a dual-ring injection mode-locked fiber ring laser as the clock recovery module and an electroabsorption modulator (EAM) as the decision gate. The clock recovery module extracts the optical short pulse clock with low timing jitter from degraded 40 Gbit/s optical data streams, while the decision gate restores their signal quality. A numerical model describing the cross-absorption modulation effect in a bulk EAM is developed to explore the operating conditions, such as bias voltage, pump signal power. The timing jitter tolerance for the EAM optical gate is also investigated. Significantly improvement of BER is obtained from 40 Gbit/s RZ signals which are degraded by polarization mode dispersion or chromatic dispersion.     

160 Gbps S-band WDM transmission system over 1400 km using ITUT-652a and ITUT-655 fibers with low dispersion accumulation

Dispersion accumulation with the distance effects optical WDM system's performance severely. For every modulation format used there is a limit on maximum transmission distance due to dispersion accumulation. So dispersion compensation is required. But dispersion compensation can be avoided to a large extent by alternatively using different fiber standards. In this paper it has been proposed that the dispersion accumulation can be reduced to a large extent by alternatively transmitting in S-band and using fiber standards ITUT-652a and ITUT-655. To validate the claim, performance of a 16 channel 10 Gbps WDM system with the proposed method has been analyzed in terms of BER and Q-factor. And it has been observed that with the proposed scheme without any dispersion compensation the system performs well up to 1400 km.     

Analysis of linewidth and extinction ratio in directly modulated lasers for performance optimization in 10 Gbit/s CWDM systems

Direct Modulation Lasers (DMLs) have attracted increased attention during the past few years because of their intrinsic simplicity and cost-effectiveness, especially when applied to WDM metro and access networks. However, the output power waveform from a directly modulated laser is not an exact replica of the modulation current and its instantaneous optical frequency varies with time depending on the changes in optical power and the extinction ratio (ER) (an effect also known as frequency chirp). In this work, using an Optical Communication System Design Software, we have studied a directly modulated WDM 10 Gb/s system which transmission performance depends strongly on DML characteristics; simulation results have provided supplementary details about the effects of DML type (adiabatic or transient chirp dominated) as well as the effects of the optical output power. These details can provide useful design guidelines for constructing a WDM metro network.     

Analysis of modulation format in the 40 Gbit/s optical communication system

Three different modulation formats including nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed return-to-zero (CS-RZ) and the differential phase keying (DPSK) modulation format of each code are introduced in the article. A method of their modulated signal generation with computer is described, and a comparison of their spectra and waveforms is made. The 40 Gbps signal transmitted in 200 km G.652 fiber by way of single channel with erbium-doped-fiber-amplifier (EDFA) is simulated for these three formats. The ability of anti-dispersion and anti-PMD is analyzed. It is shown that RZ and CS-RZ formats are more tolerant than NRZ format in the same conditions.     

Reduction of the fiber nonlinearity impairment using optical phase conjugation in 40 Gb/s CO-OFDM systems

In this paper, optical phase conjugation (OPC) located in the transmitter based on four wave mixing (FWM) in a semiconductor optical amplifier (SOA) is first simulated in 40 Gb/s CO-OFDM systems, and the fiber nonlinearity impairment of the transmission link is precompensated before OPC by transmission through a fiber with large nonlinearity coefficient. Simulation results show that the nonlinear threshold (NLT) can be increased by about > 3 dB and maximum Q factor can be increased by about 2 dB for the single-channel system. For 50-GHz-Spacing WDM systems, the maximum Q and NLT are increased by about 1 dB, even in the presence of cross phase modulation (XPM) from neighbouring WDM channels. It is found that this OPC subsystem located in the transmitter, not necessary to be inserted into the middle of link, can mitigate the fiber nonlinearity impairment for both single-channel and WDM systems.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical AWG multiplexer and AWG demultiplexer based transmission links

In this paper, we have analyzed the performance and feasibility for the metropolitan area network based on arrayed waveguide grating (AWG) multiplexers and arrayed waveguide grating (AWG) demultiplexers operating at the bitrate of 10 Gb/s. In the network, the data is successfully transmitted to a distance of 50 km with a very low BER of 1 × 10⁻⁴⁰ thus improving the performance over AWG star based networks. Here, we have observed that arrayed waveguide gratings based multiplexers and demultiplexers for WDM applications prove to be capable of precise multiplexing and demultiplexing of a large number of channels with relatively low losses. This paper also presents the comparative investigation and suitability of various data formats like NRZ Rectangular, NRZ Raised cosine, RZ Rectangular, RZ Raised cosine and RZ super Gaussian for optical transmission link. It has been shown that RZ Raised cosine yields the highest value of Q, good eye opening and lowest BER.