Interaction of some antioxidants with Belousov-Zhabotinsky reaction based on catechol-BrO 3 − -Mn2+-H2SO4 system

Temporal evolution of a new Mn(II) catalyzed Belousov-Zhabotinsky (BZ) chemical oscillator with catechol (1.2-dihydroxybenzene) as organic substrate is reported within narrow range of concentrations of initial reagents at 30°C. After optimizing the oscillation parameters the system was perturbed with the antioxidants like ascorbic acid and inosine. It is found that ascorbic acid acts as co-substrate within certain concentration limit, whereas inosine acts as a quencher of oscillations. Addition of ascorbic acid to the BZ system decreases induction time thus acting synergistically to help the reaction to enter quickly into the oscillatory regime. A good linear dependence of induction time on the concentration of ascorbic acid (R ² = 0.9948) and inosine (R ² = 0.955) is reported. Inosine has been found to increase the induction time and quench the oscillations. It is mentioned that the magnitude of induction time decreases to a greater extent with ascorbic acid as compared to the magnitude of its increase with the same concentration of inosine. This is pointing to the fact that ascorbic acid is stronger antioxidant than inosine as depicted by their interaction with catechol-based BZ chemical oscillator. Temporal evolution of the BZ reaction with the injection of antioxidants at different stages of reaction is also reported.     

Thermal Studies of New Lead(II) Coated‐Wire Membrane Electrodes

Five plastic membrane Pb²⁺‐selective electrodes were prepared based on 1,4‐bis(N‐tosyl‐o‐aminophenoxy)butane I , 1,4‐bis(N‐allyl‐N‐tosyl‐o‐aminophenoxy)butane II , 1,4‐bis(N‐benzyl‐N‐tosyl‐o‐aminophenoxy)butane III , 1,4‐bis[N‐(o‐allyloxybenzyl)‐N‐tosyl‐o‐aminophenoxy]butane IV , and 1,4‐bis(N‐octyl‐N‐tosyl‐o‐aminophenoxy)butane V as neutral carriers. The electrodes exhibited nearly Nernstian responses over the concentration ranges, 2.5×10^?4–4.0×10^?2, 2.5×10^?5–4.0×10^?2, 7.9×10^?5–4.0×10^?2, 2.2×10^?5–4.0×10^?2, and 1.9×10^?4–4.0×10^?2 M for electrodes composed with the ionophores I–V , respectively. All electrodes showed pH range of about 4.0 to 11.5 and working temperature range of 22 to 70 °C with isothermal temperature coefficients of 1.19×10^?3, 1.16×10^?3, 1.16×10^?3, 1.00×10^?3 , and 1.32×10^?3 V/°C for electrodes I–V respectively.     

Inhibitory Effects by Ascorbic Acid on the Oscillations of the Briggs?Rauscher Reaction

The Briggs? Rauscher oscillating reaction (in batch mode) has been shown to be sensitive to various antioxidants, some of which cause cessation of oscillations for a period of time, before a restart occurs. The length of time before oscillations restart is related to the type of antioxidant and its concentration. Procedures have been devised to apply this method as a tool for measuring antioxidant activities of pure compounds and of extracts of natural sources. The antioxidant activity in the Briggs? Rauscher system has been generally related to the reaction of an antioxidants with hydroperoxy radicals (HOO^.) present in the oscillating system. Thereby, at low concentration (<2×10^?4 M ), ascorbic acid is known to have a little effect on the reaction. However, there is a concentration range, where a nearly linear relation is observed between ascorbic acid concentration and inhibition time. We were able to model this type of inhibition by the reducing power of ascorbic acid without invoking a reaction with HOO^..     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

Graphene Oxide as a Platform for Copper Pentacyanonitrosylferrate Nanoparticles and their Behavior in the Electro‐oxidation of N‐Acetylcysteine

This work describes the preparation of graphene oxide by the Modified Hummers Method and the chemical modification of its surface with nanoparticles of copper pentacyanonitrosylferrate(III) (GOCuNP). The materials obtained were characterized by Raman spectroscopy, x‐ray photoelectron spectroscopy and transmission electron microscopy. The GOCuNP was characterized by cyclic voltammetry using a graphite paste electrode that presented electrocatalytic response for N‐acetylcysteine with detection limit of 2.97×10^?5 mol L^?1 at concentration range of 3.00×10^?5 to 6.00×10^?3 mol L^?1 of N‐acetylcysteine. By this way, the bimetallic complex formed is included in the list of materials obtained as potential candidates for the construction of electrochemical sensors for N‐acetylcysteine detection.     

Flow‐Injection Spectrophotometric Determination of N‐acetylcysteine in Pharmaceutical Formulations with On‐Line Solid‐Phase Reactor Containing Zn(II) Phosphate Immobilized in a Polyester Resin

Abstract

A flow‐injection spectrophotometric procedure was developed for determining N‐acetylcysteine in pharmaceutical formulations. The sample was dissolved in deionized water and 400 µl of the solution was injected into a carrier stream of 1.0×10^?2 mol l^?1 sodium borate solution. The sample flowed through a column (70 mm length×2.0 mm i.d.) packed with Zn₃(PO₄)₂ immobilized in a polymeric matrix of polyester resin and Zn(II) ions were released from the solid‐phase reactor because of the formation of the Zn(II) (N‐acetylcysteine)₂ complex. The mixture merged with a stream of borate buffer solution (pH 9.0) containing 5.0×10^?4 mol l^?1 Alizarin red S and the Zn(II)Alizarin red complex formed was measured spectrophotometrically at 540 nm. The analytical curve was linear in the N‐acetylcysteine concentration range from 3.0×10^?5 to 1.5×10^?4 mol l^?1 (4.9 to 24.5 µg ml^?1) with a detections limit of 8.0×10^?6 mol l^?1 (1.3 µg ml^?1). The relative standard deviations (RSDs) were smaller than 0.5% (n=10) for solutions containing 5.0×10^?5 mol l^?1 (8.0 µg ml^?1) and 8.0×10^?5 mol l^?1 (13.0 µg ml^?1) of N‐acetylcysteine, and the analytical frequency was 60 determinations per hour. A paired t‐test showed that all results obtained for N‐acetylcysteine in commercial formulations using the proposed flow‐injection procedure and a comparative procedure agreed at the 95% confidence level.     

Kinetic Study of Peroxidase‐Catalyzed Coupling of Benzene‐1,4‐diamine and N‐(2‐Aminoethyl)naphthalen‐1‐amine: Development of Micromolar Hydrogen Peroxide Reaction System

A novel chromogenic method to measure the peroxidase activity using para‐phenylenediamine dihydrochloride (=benzene‐1,4‐diamine hydrochloride; PPDD) and N‐(1‐naphthyl)ethylenediamine dihydrochloride (=N‐(2‐aminoethyl)naphthalen‐1‐amine; NEDA) is presented. The PPDD entraps the free radical and gets oxidized to electrophilic diimine, which couples with NEDA to give an intense red‐colored chromogenic species with maximum absorbance at 490 nm. This assay was adopted for the quantification of H₂O₂ between 20 and 160 μM . Catalytic efficiency and catalytic power of the commercial peroxidase were found to be 4.47×10⁴ M ^?1 min^?1 and 3.38×10^?4 min^?1, respectively. The catalytic constant (k_cat) and specificity constant (k_cat/K_m) at saturated concentration of the co‐substrates were 0.0245×10³ min^?1 and 0.0445 μM ^?1 min^?1, respectively. The chromogenic coupling reaction has a minimum interference from the reducing substances such as ascorbic acid, L ‐cystein, citric acid, and oxalic acid. The method being simple, rapid, precise, and sensitive, its applicability has been tested in the crude vegetable extracts that showed peroxidase activity.     

A Copper(II) Ion‐Selective Potentiometric Sensor Based on N,N′,N″,N′′′‐Tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane in PVC Matrix

The simple PVC‐based membrane containing N,N′,N″,N′′′‐tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane (tpmc) as an ionophore and dibutyl phthalate as a plasticizer, directly coated on a glassy carbon electrode was examined as a new sensor for Cu²⁺ ions. The potential response was linear within the concentration range of 1.0×10^?1–1.0×10^?6 M with a Nernstian slope of 28.8 mV/decade and detection limit of 7.0×10^?7 M. The electrode was used in aqueous solutions over a wide pH range (1.3–6). The sensor exhibited excellent selectivity for Cu²⁺ ion over a number of cations and was successfully used in its determination in real samples.     

Supramolecular Assembly of β‐Cyclodextrin‐Capped Gold Nanoparticles on Ferrocene‐Functionalized ITO Surface for Enhanced Voltammetric Analysis of Ascorbic Acid

A supramolecular recognition functionalized electrode (βCD‐nanoAu/Fc‐ITO) which exhibits redox‐activity was prepared through supramolecular assembly of β‐cyclodextrin (βCD) capped gold nanoparticles (βCD‐nanoAu) on the ITO previously coated with a monolayer of ferrocene residues (Fc‐ITO). The immobilization of βCD‐nanoAu on Fc‐ITO was confirmed by atomic force microscopy (AFM), and the supramolecular nature of the immobilization approach was also confirmed by cyclic voltammetry. On the other hand, the electrocatalytic activity of βCD‐nanoAu/Fc‐ITO electrode was also studied. The electrocatalytic activity toward ascorbic acid (AA) was enhanced compared with that at the Fc‐ITO electrode, and a linear relationship existed between the anodic peak and the concentration of AA in the range of 5.3×10^?5 to 3.0×10^?3 M with a detection limit (S/N=3) of 4.1×10^?6 M.     

Simultaneous Determination of Dopamine and Ascorbic Acid at an In‐Site Functionalized Self‐Assembled Monolayer on Gold Electrode

The in‐site functionalization of 4‐aminothiophenol (4‐ATP) self‐assembled monolayer on gold electrode at physiological pH yields a redox active monolayer of 4′‐mercapto‐N‐phenylquinone diimine (MNPD). The functionalized electrode exhibits excellent electrocatalytic responses towards dopamine (DA) and ascorbic acid (AA), reducing the overpotentials by about 0.22 V and 0.34 V, respectively, with greatly enhanced current responses. Due to its different catalytic activities toward DA and AA, the modified electrode resolves the overlapping voltammetric responses of DA and AA into two well‐defined voltammetric peaks by differential pulse voltammetry (DPV), which can be used for the simultaneous determination of these species in a mixture. The catalytic peak current obtained from DPV was linearly related to DA and AA concentration in the ranges of 5.0×10^?6?1.25×10^?4 M and 8.0×10^?6?1.3×10^?4 M with correlation coefficient of 0.999 and 0.998, respectively. The detective limits (3σ) for DA and AA were found to be 1.2×10^?6 M and 2.4×10^?6 M, respectively. The modified electrode shows good sensitivity, selectivity and stability, and has been applied to the determination of DA and AA simultaneously in samples with satisfactory results.     

Electrocatalytic Oxidation and Determination of Cysteamine by Poly‐N,N‐dimethylaniline/Ferrocyanide Film Modified Carbon Paste Electrode

Functionalized poly‐N,N‐dimethylaniline film was prepared by adsorption of ferrocyanide onto the polymer forming at the surface of carbon paste electrode (CPE) in aqueous solution by using potentiostatic method. The electrocatalytic ability of poly‐N,N‐dimethylaniline/ferrocyanide film modified carbon paste electrode (PDMA/FMCPE) was demonstrated by oxidation of cysteamine. Cyclic voltammetry and chronoamperometry techniques were used to investigate this ability. Results showed that pH 7.00 is the most suitable for this purpose. It is found that the catalytic reaction rate constant, (k_h), is equal to 2.142×10³ M^?1 s^?1 by the data of chronoamperometry. The catalytic reduction peak current was linearly dependent on the cysteamine concentration and the linearity range obtained was 8.00×10^?5 M–1.14×10^?2 M. Detection limit was determined 7.97×10^?5 M (2σ). This method has been successfully employed for quantification of cysteamine in real sample.     

Halide‐Anion Binding by Singly and Doubly N‐Confused Porphyrins

The halide‐binding properties of N‐confused porphyrin (NCP, 1 ) and doubly N‐confused porphyrins (trans‐N₂CP ( 2 ), cis‐N₂CP ( 3 )) were examined in CH₂Cl₂. In the free‐base forms, cis‐N₂CP ( 3 ) showed the highest affinity to each anion (Cl^?, Br^?, I^?) with association constants K_a=7.8×10³, 1.9×10³, and 5.8×10² M ^?1, respectively. As metal complexes, on the other hand, trans‐N₂CP 2–Cu exhibited the highest affinity to Cl^?, Br^?, and I^? with K_a=9.0×10⁴, 2.7×10⁴, and 1.9×10³ M ^?1, respectively. The corresponding K_a values for cis‐N₂CP 3–Cu and NCP 1–Cu were about 1/10 and 1/2, respectively, of those of 2–Cu . With the help of density functional theory (DFT) calculations and complementary affinity measurements of a series of trisubstituted N‐confused porphyrins, the efficient anion binding of NCPs was attributed to strong hydrogen bonding at the highly polarized NH moieties owing to the electron‐deficient C₆F₅ groups at meso positions as well as the ideally oriented dipole moments and large molecular polarizability. The orientation and magnitude of the dipole moments in NCPs were suggested to be important factors in the differentiation of the affinity for anions.     

A Novel Al(III)‐Selective Electrochemical Sensor Based on N,N′‐Bis(salicylidene)‐1,2‐phenylenediamine Complexes

A polyvinylchloride membrane sensor based on N,N′‐bis(salecylidene)‐1,2‐phenylenediamine (salophen) as membrane carrier was prepared and investigated as a Al³⁺‐selective electrode. The sensor exhibits a Nernstian response toward Al(III) over a wide concentration range (8.0×10^?7–3.0×10^?2 M), with a detection limit of 6.0×10^?7 M. The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 3.2–4.5. The electrode possesses advantages of very fast response and high selectivity for Al³⁺ in comparison with alkali, alkaline earth and some heavy metal ions. The sensor was used as an indicator electrode, in the potentiometric titration of aluminum ion and in determination of Al³⁺ contents in drug, water and waste water samples.     

Polymeric Membrane Lanthanum(III)‐Selective Electrode Based on N,N′‐Adipylbis(5‐phenylazo salicylaldehyde hydrazone)

A recently synthesized azao‐containing Schiff's base N,N′‐adipylbis(5‐phenylazo salicylaldehyde hydrazone) was used as a suitable neutral ion carrier in construction of a highly selective La³⁺‐PVC membrane electrode. The electrode exhibits a Nernstian response with a slope of 19.4 mV decade^?1 over a wide concentration range (1.0×10^?6–1.0×10^?2 M) and a limit of detection of 4.0×10^?7 M (0.05 ppm). The electrode possesses a fast response time of ca. 10 s and can be used for at least 3 months without observing any deviation. The proposed electrode revealed excellent selectivity for La³⁺ over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.0–8.0. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of La³⁺ ions with EDTA and in determination of F^? ion in some pharmaceutical preparations.     

Simultaneous Determination of Ascorbic Acid and Uric Acid by Using a PVC/TTF‐TCNQ Composite Electrode as Detector in a FIA System

A PVC/TTF‐TCNQ composite electrode has been employed as detector in a flow injection system. The proposed method allows the simultaneous detection of ascorbic acid (AA) and uric acid (UA) in mixtures by using a FIA system in a simple manner, without pre‐treatment or modified electrode. This method is based on the amperometric determination of (a) ascorbic acid at 0.15 V and (b) both analytes at 0.35 V, being the response linear in the range 1×10^?2–4×10^?4 M for both analytes with detection limits (S/N=3) of 1.2×10^?4 M and 8.1×10^?5 M for AA and UA, respectively.     

Sensitive amperometric pyridoxine sensor based on self‐assembled Prussian blue nanoparticle‐modified poly(o‐phenylenediamine)/glassy carbon electrode

Prussian blue nanoparticles (PBNPs) were prepared by a self‐assembly process on a glassy carbon electrode (GCE) modified with poly(o‐phenylenediamine) (PoPD) film. The stepwise fabrication process of PBNP‐modified PoPD/GCE was characterized using scanning electron microscopy and electrochemical impedance spectroscopy. The prepared PBNPs showed an average size of 70 nm and a homogeneous distribution on the surface of the modified electrode. The PBNPs/PoPD/GCE showed electrocatalytic activity towards the oxidation of pyridoxine (PN) and was used as an amperometric sensor. The modified electrode exhibited a linear response for PN oxidation over the concentration range 3–38.5 μM with a detection limit of ca 6.10 × 10^?7 M (S/N = 3) and sensitivity of 2.79936 × 10³ mA M^?1 cm^?2 using an amperometric method. The mechanism and kinetics of the catalytic oxidation reaction of PN were investigated using cyclic voltammetry and chronoamperometry. The values of α, k_cat and D were estimated as 0.36, 1.089 × 10² M^?1 s^?1 and 8.9 × 10^?5 cm² s^?1, respectively. This sensor also exhibited good anti‐interference and selectivity. Copyright © 2016 John Wiley & Sons, Ltd.     

Gas‐phase ozonolysis: Rate coefficients for a series of terpenes and rate coefficients and OH yields for 2‐methyl‐2‐butene and 2,3‐dimethyl‐2‐butene

The kinetics of the gas‐phase reactions of O₃ with a series of selected terpenes has been investigated under flow‐tube conditions at a pressure of 100 mbar synthetic air at 295 ± 0.5 K. In the presence of a large excess of m‐xylene as an OH radical scavenger, rate coefficients k(O₃+terpene) were obtained with a relative rate technique, (unit: cm³ molecule^?1 s^?1, errors represent 2σ): α‐pinene: (1.1 ± 0.2) × 10^?16, ³Δ‐carene: (5.9 ± 1.0) × 10^?17, limonene: (2.5 ± 0.3) × 10^?16, myrcene: (4.8 ± 0.6) × 10^?16, trans‐ocimene: (5.5 ± 0.8) × 10^?16, terpinolene: (1.6 ± 0.4) × 10^?15 and α‐terpinene: (1.5 ± 0.4) × 10^?14. Absolute rate coefficients for the reaction of O₃ with the used reference substances (2‐methyl‐2‐butene and 2,3‐dimethyl‐2‐butene) were measured in a stopped‐flow system at a pressure of 500 mbar synthetic air at 295 ± 2 K using FT‐IR spectroscopy, (unit: cm³ molecule^?1 s^?1, errors represent 2σ ): 2‐methyl‐2‐butene: (4.1 ± 0.5) × 10^?16 and 2,3‐dimethyl‐2‐butene: (1.0 ± 0.2) × 10^?15. In addition, OH radical yields were found to be 0.47 ± 0.04 for 2‐methyl‐2‐butene and 0.77 ± 0.04 for 2,3‐dimethyl‐2‐butene. © 2002 Wiley Periodicals, Inc. Int J Chem Kinet 34: 394–403, 2002     

A chronoamperometric method for determining total antioxidant activity

A novel version of a chronoamperometric method of antioxidant determination is described. It is based on the use of the oxidation current of ferrocyanide formed in the reaction of antioxidants to be determined with potassium ferricyanide as an analytical signal. So the total concentration of all antioxidants present in the analyzed solution, i.e., total antioxidant capacity, is measured. The results of blood plasma analysis by the newly presented and certified potentiometry method are in good agreement with each other, R ² = 0.9980. The detection limit makes 2 × 10⁻⁶ M for uric and ascorbic acids and 5 × 10⁻⁶ M for cysteine and glutathione.     

A Selective Voltammetric Method for Uric Acid Detection at a Glassy Carbon Electrode Modified with Electrodeposited Film Containing DNA and Pt‐Fe(III) Nanocomposites

A novel biosensor by electrochemical codeposited Pt‐Fe(III) nanocomposites and DNA film was constructed and applied to the detection of uric acid (UA) in the presence of high concentration of ascorbic acid (AA). Based on its strong catalytic activity toward the oxidation of UA and AA, the modified electrode resolved the overlapping voltammetric response of UA and AA into two well‐defined peaks with a large anodic peak difference (ΔE_pa) of about 380mV. The catalytic peak current obtained from differential pulse voltammetry (DPV) was linearly dependent on the UA concentration from 3.8×10^?6 to 1.6×10^?4 M (r=0.9967) with coexistence of 5.0×10^?4 M AA. The detection limit was 1.8×10^?6 M (S/N=3) and the presence of 20 times higher concentration of AA did not interfere with the determination. The modified electrode shows good sensitivity, selectivity and stability.     

Novel Dy(III) Sensor Based on a New Bis‐Pyrrolidene Schiff's Base

In this work a dysprosium [Dy(III)]‐selective solvent polymeric membrane sensor based on N,N‐bis(pyrrolidene) benzne‐1,2‐diamine, poly(vinyl chloride)(PVC), the plasticizer benzylacetate (BA), and anionic site is described. This sensor responds to Dy(III) activity in a linear range from 1.0×10^?5 to 1.0×10^?1 M, with a slope of 20.6±0.2 mV per decade and a detection limit of 6.0×10^?6 M at the pH range of 3.5–8.0. It has a fast response time of<20 s in the entire concentration range, and can be used for at least 2 months without any considerable divergence in the electrode potentials. The proposed sensor revealed comparatively good selectivity with respect to common alkali, alkaline earth, transition and heavy metal ions. It was used as an indicator electrode in the potentiometric titration of fluoride ions and in determination of concentration of F ^– ions in some mouth washing solutions.