Electrochemical deposition of silicate–cetyltrimethylammonium bromide nanocomposite film on glassy carbon electrode for sensing of methyl parathion

A novel electrochemical sensor for methyl parathion based on silicate– cetyltrimethylammonium bromide nanocomposite film has been fabricated by electro-assisted deposition onto glassy carbon electrode in one-step via an electrochemical modulation of pH at the electrode/solution interface to promote controlled gelification of tetraethylorthosilicate sol, and was characterized with scanning electron microscopy, X-ray diffraction, and electrochemical impedance spectroscopy. The electrochemical sensing of methyl parathion on the film-modified electrode was investigated applying cyclic voltammetry and square wave voltammetry. Compared to the unmodified electrode, the shapes of the redox peaks were improved and the peak currents significantly increased. Experimental parameters such as deposition time, pH value, and accumulation conditions have been optimized. A linear relationship between the peak current and methyl parathion concentration was obtained in the range from 1.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.04 × 10 ⁻⁸ mol L⁻¹ (S/N = 3) after accumulation at 0 V for 120 s. The film electrode shows great promise for determination of methyl parathion in real samples.      

A hydrogen peroxide biosensor based on direct electrochemistry of hemoglobin in palladium nanoparticles/graphene-chitosan nanocomposite film

Thermally two-dimensional lattice graphene (GR) and biocompatibility chitosan (CS) act as a suitable support for the deposition of palladium nanoparticles (PdNPs). A novel hydrogen peroxide (H₂O₂) biosensor based on immobilization of hemoglobin (Hb) in thin film of CS containing GR and PdNPs was developed. The surface morphologies of a set of representative membranes were characterized by means of scanning electron microscopy and showed that the PdNPs are of a sphere shape and an average diameter of 50 nm. Under the optimal conditions, the immobilized Hb showed fast and excellent electrocatalytic activity to H₂O₂ with a small Michaelis–Menten constant of 16 μmol L⁻¹, a linear range from 2.0 × 10⁻⁶ to 1.1 × 10⁻³ mol L⁻¹, and a detection limit of 6.6 × 10⁻⁷ mol L⁻¹. The biosensor also exhibited other advantages, good reproducibility, and long-term stability, and PdNPs/GR–CS nanocomposites film would be a promising material in the preparation of third generation biosensor.     

The inhibition mechanism of pitting corrosion of pure aluminum by nitrate and sulfate ions in neutral chloride solution

The inhibition mechanism of pitting corrosion of natural oxide film-covered pure aluminum by NO⁻ ₃ and SO²⁻ ₄ ions has been examined in 0.1 M NaCl solution using potentiodynamic polarization experiments, a.c. impedance spectroscopy, Auger electron spectroscopy and a combination of the potentiostatic current transient method and optical microscopy. It was found that NO⁻ ₃ ions can be incorporated into the natural oxide film on pure aluminum at open-circuit potential, but the incorporation of SO²⁻ ₄ ions into the film hardly occurs. The incorporation of NO⁻ ₃ ions lowered the pitting susceptibility of pure aluminum in 0.1 M NaCl solution. Based upon the experimental results, it is suggested that the pitting corrosion inhibition mechanism by anions can be classified into two different groups: inhibition by competitive adsorption of anions (SO²⁻ ₄) with Cl⁻ ions and inhibition by the incorporation of anions (NO⁻ ₃) into the film rather than competitive adsorption. Both cases may impede the incorporation of Cl⁻ ions into the film, thus inhibiting pitting corrosion of natural oxide film-covered pure aluminum in chloride solutions. Received: 16 October 1998 / Accepted: 6 January 1999     

Ethanol Production from Cashew Apple Bagasse: Improvement of Enzymatic Hydrolysis by Microwave-Assisted Alkali Pretreatment

In this work, the potential of microwave-assisted alkali pretreatment in order to improve the rupture of the recalcitrant structures of the cashew able bagasse (CAB), lignocellulosic by-product in Brazil with no commercial value, is obtained from cashew apple process to juice production, was studied. First, biomass composition of CAB was determined, and the percentage of glucan and lignin was 20.54 ± 0.70% and 33.80 ± 1.30%, respectively. CAB content in terms of cellulose, hemicelluloses, and lignin, 19.21 ± 0.35%, 12.05 ± 0.37%, and 38.11 ± 0.08%, respectively, was also determined. Results showed that, after enzymatic hydrolysis, alkali concentration exerted influence on glucose formation, after pretreatment with 0.2 and 1.0 mo L⁻¹ of NaOH (372 ± 12 and 355 ± 37 mg g_glucan⁻¹) when 2% (w/v) of cashew apple bagasse pretreated by microwave-assisted alkali pretreatment (CAB-M) was used. On the other hand, pretreatment time (15–30 min) and microwave power (600–900 W) exerted no significant effect on hydrolysis. On enzymatic hydrolysis step, improvement on solid percentage (16% w/v) and enzyme load (30 FPU g_CAB-M⁻¹) increased glucose concentration to 15 g L⁻¹. The fermentation of the hydrolyzate by Saccharomyces cerevesiae resulted in ethanol concentration and productivity of 5.6 g L⁻¹ and 1.41 g L⁻¹ h⁻¹, respectively.     

Preparation and characterization of AuPt alloy nanoparticle–multi-walled carbon nanotube–ionic liquid composite film for electrocatalytic oxidation of cysteine

Gold–platinum (AuPt) alloy particles were fabricated directly on multi-walled carbon nanotubes (MWNT)–ionic liquid (i.e., trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide, [P_6,6,6,14][NTf₂]) composite coated glassy carbon electrode (GCE) by electrodeposition method. Scanning electron microscope image showed that they were well-dispersed nanocluster consisting of smaller nanoparticles, and their size was about 70 nm. X-ray diffraction experiment showed that they were single-phase alloy nanomaterial, and the calculated composition was consisting with that obtained by energy dispersive X-ray spectroscopy. The resulting modified electrode (i.e., AuPt–MWNT–[P_6,6,6,14][NTf₂]/GCE) presented high catalytic activity for the electrochemical oxidation of cysteine. The peak potential of cysteine shifted to 0.42 V (versus saturated calomel electrode) in 0.1 M H₂SO₄ and the peak current increased greatly in comparison with that on the corresponding Pt (or Au)–MWNT–[P_6,6,6,14][NTf₂]/GCE. Under the optimized conditions, the oxidation current of cysteine at 0.45 V was linear to its concentration in the range of 5.0 × 10⁻⁷ ∼ 4.0 × 10⁻⁵ M with a sensitivity of 43.8 mA M⁻¹.     

Langmuir–Blodgett film of tetraoxocalix[2]arene[2]triazine modified electrode for voltammetric determination of copper ion

In the present work, a new voltammetric sensor, Langmuir–Blodgett (LB) film of tetraoxocalix[2]arene[2]triazine (TOCT) modified glassy carbon electrode (LB_TOCT-GCE), for trace analysis of copper ion in water samples, was prepared. The morphology of LB_TOCT-GCE was characterized by cyclic voltammetric method, electrochemical impedance spectroscopy, and atomic force microscope. The recognizing mechanism of LB_TOCT-GCE for copper ion in aqueous solution was discussed. Under the optimum experimental conditions, using square wave stripping voltammetry and accumulation time of 300 s, the peak currents were linear relationship with Cu²⁺ concentrations in the range of 2 × 10⁻⁹ to 1 × 10⁻⁶ mol L⁻¹, with detection limit of 1 × 10⁻¹⁰ mol L⁻¹. By this method, real samples (lake water, drinking water, and city wastewater) were analyzed with satisfactory results. In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility, and stability.     

Application of a Single-Wall Carbon Nano-Tube Film Electrode to the Determination of Trace Amounts of Folic Acid

Single-wall carbon nano-tubes were used to modify the surface of a glassy carbon electrode (GC) and applied in the determination of folic acid with voltammetry. The experiments demonstrated that the presence of a carbon nano-tube film on the electrode greatly increased the reduction peak current of folic acid. Cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were used in a comparative investigation of the electrochemical reduction of folic acid with the film electrode. Effects of pH on the peak current and the peak potential were studied in the pH range of 4.0–8.0 with Britton-Robinson buffer solution. The reduction peak current was found to be linearly related to folic acid concentration over the range of 1 × 10⁻⁸ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 1 × 10⁻⁹ mol L⁻¹ after 5 min accumulation. The film electrode provides an efficient way for eliminating interferences from some inorganic and organic species in the solution. The high sensitivity, selectivity and stability of the film electrode demonstrate its practical application from a simple and rapid determination of folic acid in tablets.     

A new amperometric H<Subscript>2</Subscript>O<Subscript>2</Subscript> biosensor based on nanocomposite films of chitosan–MWNTs,hemoglobin, and silver nanoparticles

A new H₂O₂ biosensor was fabricated on the basis of nanocomposite films of hemoglobin (Hb), silver nanoparticles (AgNPs), and multiwalled carbon nanotubes (MWNTs)–chitosan (Chit) dispersed solution immobilized on glassy carbon electrode (GCE). The immobilized Hb displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ′) of −22.5 mV in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) in the Chit–MWNTs film was evaluated as 2.58 s⁻¹ according to Laviron’s equation. The surface concentration (Γ*) of the electroactive Hb in the Chit–MWNTs film was estimated to be (2.48 ± 0.25) × 10⁻⁹ mol cm⁻². Meanwhile, the Chit–MWNTs/Hb/AgNPs/GCE demonstrated excellently electrocatalytical ability to H₂O₂. Its apparent Michaelis–Menten constant (K _M^app) for H₂O₂ was 0.0032 mM, showing a good affinity. Under optimal conditions, the biosensors could be used for the determination of H₂O₂ ranging from 6.25 × 10⁻⁶ to 9.30 × 10⁻⁵ mol L⁻¹ with a detection limit of 3.47 × 10⁻⁷ mol L⁻¹ (S/N = 3). Furthermore, the biosensor possessed rapid response to H₂O₂ and good stability, selectivity, and reproducibility.     

The effect of chloride concentration and pH on pitting corrosion of AA7075 aluminum alloy coated with phenyltrimethoxysilane

The effect of chloride ion concentration and pH of solution on the corrosion behavior of aluminum alloy AA7075 coated with phenyltrimethoxysilane (PTMS) immersed in aqueous solutions of NaCl is reported. Potentiodynamic polarization, linear polarization, open circuit potential, and weight loss measurements were performed. The surface of samples was examined using SEM and optical microscopy. Elemental characterization of the coating by secondary ion mass spectrometry indicates an intermediate layer between coating and aluminum alloy surface. The corrosion behavior of the aluminum alloy AA7075 depends on chloride concentration and pH of solution. In acidic or neutral solutions, general and pitting corrosion occur simultaneously. On the contrary, exposure to alkaline solutions results in general corrosion only. Results further reveal that aluminum alloy AA7075 is susceptible to pitting corrosion in all chloride solutions with concentrations between 0.05 M and 2 M NaCl; an increase in the chloride concentration slightly shifted both the pitting and corrosion potentials to more active values. Linear polarization resistance measurements show a substantially improved corrosion resistance value in case of samples coated with PTMS as compared to uncoated samples in both neutral (pH = 7), acidic (pH = 0.85 and 3), and alkaline chloride solutions (pH = 10 and 12.85). The higher corrosion resistance of the aluminum alloy coated with PTMS can be attributed to the hydrophobic coating which acts as a barrier and prevents chloride ion penetration and subsequent reaction with the aluminum alloy.     

Simple sensor for simultaneous determination of dihydroxybenzene isomers

A simple sensor based on bare carbon ionic liquid electrode was fabricated for simultaneous determination of dihydroxybenzene isomers in 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0). The oxidation peak potential of hydroquinone was about 0.136 V, catechol was about 0.240 V, and resorcinol 0.632 V by differential pulse voltammetric measurements, which indicated that the dihydroxybenzene isomers could be separated absolutely. The sensor showed wide linear behaviors in the range of 5.0 × 10⁻⁷–2.0 × 10⁻⁴ mol L⁻¹ for hydroquinone and catechol, 3.5 × 10⁻⁶–1.535 × 10⁻⁴ mol L⁻¹ for resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 5.0 × 10⁻⁸, 2.0 × 10⁻⁷, 5.0 × 10⁻⁷ mol L⁻¹, respectively (S/N = 3). The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater and the recovery was from 93.9% to 104.6%.     

Sensitive voltammetric sensor of dihydromyricetin based on Nafion/SWNT-modified glassy carbon electrode

A novel voltammetric sensor, based on single-walled carbon nanotubes (SWNT) dispersed in Nafion and modified glassy carbon electrode (GCE), was fabricated and used to determine the trace amounts of dihydromyricetin (DMY). The electrochemical behavior of DMY at this sensor was investigated in 0.1 mol L⁻¹ sulfuric acid solutions + 0.1 mol L⁻¹ NaCl by cyclic voltammetry and squarewave voltammetry. Compared with bare GCE, the electrode presented an excellent response of DMY through an adsorption-controlled quasi-reversible process. Under the optimum conditions, the response peak currents were linear relationship with the DMY concentrations in the range of 1.0 × 10⁻⁷–1.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 9 × 10⁻⁸ mol L⁻¹. Based on this voltammetric sensor, a simple and sensitive electroanalytical method for DMY was proposed and applied to quantitative determination of DMY in Ampelopsis grossedentata samples. In addition, the oxidation mechanism was proposed and discussed, which could be a reference for the pharmacological action of DMY in clinical study.     

Applications of nanostructured Pt-Au hybrid film for the simultaneous determination of catecholamines in the presence of ascorbic acid

Nanostructured platinum-gold (Pt–Au) hybrid film modified glassy carbon electrode (GCE) was fabricated by electro-deposition method in the presence of 2 × 10⁻⁴ mol l⁻¹ l-cysteine. To examine the surface morphological analysis, the (Pt–Au) hybrid film were electrochemically deposited on transparent semiconductor indium tin oxide (ITO) electrodes for scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) studies. From the SEM analysis, it was observed that the deposited nanoplatinum (250–400 nm) was formed as a cauliflower-shaped structure with the gold nanoparticles (30–90 nm). The concentration variation of additive l-cysteine results in the formation of cauliflower-shaped platinum nanoparticles. Further, the Pt–Au hybrid film modified GCE could be used for the detection of catecholamine neurotransmitters epinephrine (EP), norepinephrine (NEP) individually and in the presence of ascorbic acid (AA) in pH 7 phosphate-buffered solutions (PBS). Furthermore, the proposed Pt–Au hybrid film could be applied for the detection of epinephrine in injection solution and ascorbic acid from commercially available vitamin C tablets.     

Voltammetric determination of 2-chlorophenol using a glassy carbon electrode coated with multi-wall carbon nanotube-dicetyl phosphate film

Multi-wall carbon nanotubes (MWNT) were dispersed into water in the presence of dicetyl phosphate (DCP), and MWNT-DCP composite film coated glassy carbon electrodes (GCE) were constructed. The electrochemical properties of 2-chlorophenol at a bare GCE and MWNT-DCP modified GCE were compared. It was found that MWNT-DCP modified GCEs significantly enhance the oxidation peak current of 2-chlorophenol and lowers its oxidation overpotential, suggesting great potential in the sensitive determination of 2-chlorophenol. Finally, a sensitive and simple voltammetric method was developed for the determination of 2-chlorophenol. The oxidation peak current increases linearly with the concentration in the range of 1.0 × 10⁻⁷–2.0 × 10⁻⁵ mol L⁻¹, and the detection limit is 4.0 × 10⁻⁸ mol L⁻¹ for 2 min accumulation. The method was successfully used to determine 2-chlorophenol in waste water samples.     

Simultaneous Determination of Dopamine and Ascorbic Acid at a Triazole Self-Assembled Monolayer-Modified Gold Electrode

A 3-amino-5-mercapto-1,2,4-triazole (TA) self-assembled monolayer-modified gold electrode (TA SAM/Au) is characterized by X-ray photoelectron spectroscopy, A.C. impedance, cyclic voltammetry, chronoamperometry and chronocoulometry. The TA SAM/Au exhibited good promotion of the electrochemical oxidation of dopamine. Some electrochemical parameters of dopamine such as electron transfer number, exchange current density, standard heterogeneous rate constant, diffusion coefficient, etc., were measured by different electrochemical methods. The peak currents of dopamine were linearly dependent on its concentration in the range of 1.5 × 10⁻⁶–1.0 × 10⁻⁴ mol L⁻¹, with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. The oxidative peak potentials of dopamine and ascorbic acid were well separated at about 190 ± 10 mV in pH 2.0 BR buffers at TA SAM/Au, the oxidation peak current increases approximately linearly with increasing concentration of both dopamine and ascorbic acid in the concentration range of 9.98 × 10⁻⁶–4.54 × 10⁻⁴ mol L⁻¹. It can be used for simultaneous determination of dopamine and ascorbic acid.     

Electroless Ni–P coated on graphite as catalyst for the electro-oxidation of dextrose in alkali solution

Graphite particles were coated with Ni–P by electroless deposition using a conventional bath consisting of a nickel salt and hypophosphite. After 15 min of electroless deposition, the graphite particles were covered with 10 wt% nickel and 0.7–1.0 wt% phosphorus as analysed by wet chemical method. Surface morphology was studied by scanning electron microscopy (SEM). Electrochemical characterisation for the catalytic activity was done by cyclic voltammetry. Pure Ni powder and electroless Ni–P coated on graphite were used as catalysts for the electro-oxidation of dextrose (1.8 × 10⁻³ to 4.5 × 10⁻³ M) in 0.1 M KOH solution. Comparative studies revealed that electroless Ni–P coated on graphite particles acted as a better catalyst than pure Ni powder for catalytic reaction.     

Selective and sensitive molecularly imprinted sol–gel film-based electrochemical sensor combining mercaptoacetic acid-modified PbS nanoparticles with Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Au–multi-walled carbon nanotubes–chitosan

A sensitive molecularly imprinted electrochemical sensor was developed for selective detection of streptomycin by combination of mercaptoacetic acid-modified PbS nanoparticles with Au-coated Fe₃O₄ magnetic nanoparticles dispersed multi-walled carbon nanotubes doped chitosan film. The imprinted sensor was fabricated onto the Au electrode via stepwise modification of nanocomposites and an electrodeposited thin film of molecularly imprinted polymers via sol–gel technology. The morphologies and electrochemical behaviors of the imprinted sensor were characterized by scanning electron microscope, cyclic voltammetry, and differential pulse voltammetry, respectively. The prepared sensor showed very high recognition ability and selectivity for streptomycin. Under optimal conditions, the imprinted sensor displayed good electrocatalytic activity to the redox of streptomycin. And the differential voltammetric anodic peak current was linear to the logarithm of streptomycin concentration in the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻³ mol L⁻¹, and the detection limit obtained was 1.5 × 10⁻⁹ mol L⁻¹. This proposed imprinted sensor was used successfully for streptomycin determination in different injection solution samples.     

Covalent Modification of Glassy Carbon Electrode with L-Cysteine for the Determination of Acetaminophen

A novel L-cysteine film modified electrode has been fabricated by means of an electrochemical oxidation procedure, and it was successfully applied to the electrochemical determination of acetaminophen. This method utilizes the electrooxidation of amines to their analogous cation radicals to form a chemically stable covalent linkage between the nitrogen atom of the amine and edge plane sites at the glassy carbon electrode surface. The electrochemical behaviour of acetaminophen at the film electrode was investigated in 0.1 mol L⁻¹ phosphate buffer (pH 6.20). It was found that the redox peak current of acetaminophen was enhanced greatly on the film electrode. Linearity between the oxidation peak current and the acetaminophen concentration was obtained in the range of 1.0 × 10⁻⁴–2.0 × 10⁻⁷ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. For seven parallel detections of 1.0 × 10⁻⁵ mol L⁻¹ acetaminophen, the relative standard deviation (RSD) was 1.46%, suggesting that the film electrode has excellent reproducibility. Application to the determination of acetaminophen in drug tablets and human urine demonstrated that the film electrode has good stability and high sensitivity.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Effect of Substrate Concentration on Dark Fermentation Hydrogen Production Using an Anaerobic Fluidized Bed Reactor

The effect of substrate (glucose) concentration on the stability and yield of a continuous fermentative process that produces hydrogen was studied. Four anaerobic fluidized bed reactors (AFBRs) were operated with a hydraulic retention time (HRT) from 1 to 8 h and an influent glucose concentration from 2 to 25 g L⁻¹. The reactors were inoculated with thermally pre-treated anaerobic sludge and operated at a temperature of 30 °C with an influent pH around 5.5 and an effluent pH of about 3.5. The AFBRs with a HRT of 2 h and a feed strength of 2, 4, and 10 g L⁻¹ showed satisfactory H₂ production performance, but the reactor fed with 25 g L⁻¹ of glucose did not. The highest hydrogen yield value was obtained in the reactor with a glucose concentration of 2 g L⁻¹ when it was operated at a HRT of 2 h. The maximum hydrogen production rate value was achieved in the reactor with a HRT of 1 h and a feed strength of 10 g L⁻¹. The AFBRs operated with glucose concentrations of 2 and 4 g L⁻¹ produced greater amounts of acetic and butyric acids, while AFBRs with higher glucose concentrations produced a greater amount of solvents.     

Ensemble of carbon fiber ultra-microelectrodes modified with nanotubes, and its application to the determination of dopamine

An ensemble of carbon fibers ultra-microelectrode modified with carbon nanotubes (EUME-CNTS) has been constructed based on a thin carbon nanotubes film which was coated onto surfaces of carbon fibers of ultra-microelectrode. SEM micrographs illustrated the image of carbon nanotubes on the carbon fiber surface. The electrochemical characteristics of the EUME-CNTS has been investigated by cyclic voltammetry. The electrochemical properties of dopamine on this electrode were also studied, and the detection limit was found to be 2.0 × 10⁻⁹ mol·L⁻¹. Linear calibration plots were obtained for the oxidation peak current in a range 1.0 × 10⁻⁷–8.0 × 10⁻⁵ mol·L⁻¹. Correspondence: Xiuhua Liu, Kuaizhi Liu, Department of Chemistry and Chemical Engineering, Henan University, Henan Kaifeng 475001, P.R. China