Optical and electrical characteristics of Al-doped ZnO thin films prepared by aqueous phase deposition

Transparent conducting Al-doped ZnO (AZO) thin films have been deposited by sol-gel route. Starting from an aqueous solution of zinc acetate by adding aluminum chloride as dopant, a c-axis oriented polycrystalline ZnO thin film 100 nm in thickness could be spin-coated on glass substrates via a two-step annealing process under reducing atmosphere. The effects of thermal annealing and dopant concentration on the structural, electrical and optical properties of AZO thin films were investigated. The post-treated AZO films exhibited a homogenous dense microstructure with grain sizes less than 10 nm as characterized by SEM photographs. The annealing atmosphere has prominent impact on the crystallinity of the films which will in turn influence the electrical conductivity. By varying the doping concentrations, the optical and electrical properties could be further adjusted. An optimal doping concentration of Al/Zn = 2.25 at.% was obtained with minimum resistivity of 9.90 × 10⁻³ Ω-cm whereas the carrier concentration and mobility was 1.25 × 10²⁰ cm⁻³ and 5.04 cm² V⁻¹ s⁻¹, respectively. In this case, the optical transmittance in the visible region is over 90%.     

Preparation and characterization of n-type conductive (Al, Co) co-doped ZnO thin films deposited by sputtering from aerogel nanopowders

Highly transparent, n-type conducting ZnO thin films were obtained by low temperature magnetron sputtering of (Co, Al) co-doped ZnO nanocrystalline aerogels. The nanoparticles of ∼30 nm size were synthesized by a sol-gel method using supercritical drying in ethyl alcohol. The structural, optical and electrical properties of the films were investigated. The ZnO films were polycrystalline textured, preferentially oriented with the (0 0 2) crystallographic direction normal to the film plane. The films show within the visible wavelength region an optical transmittance of more than 90% and a low electrical resistivity of 3.5 × 10⁻⁴ Ω cm at room temperature.     

Deposition and characterization of transparent and conductive sprayed ZnO:B thin films

Highly transparent and conductive Boron doped zinc oxide (ZnO:B) thin films were deposited using chemical spray pyrolysis (CSP) technique on glass substrate. The effect of variation of boron doping concentration in reducing solution on film properties was investigated. Low angle X-ray analysis showed that the films were polycrystalline fitting well with a hexagonal wurtzite structure and have preferred orientation in [002] direction. The films with resistivity 2.54×10⁻³ Ω-cm and optical transmittance >90% were obtained at optimized boron doping concentration. The optical band gap of ZnO:B films was found ∼3.27 eV from the optical transmittance spectra for the as-deposited films. Due to their excellent optical and electrical properties, ZnO:B films are promising contender for their potential use as transparent window layer and electrodes in solar cells.     

Effect of substrate temperature on properties of multilayer thin film based on ZnO and Mo-doped indium oxide

Zinc oxide/molybdenum-doped indium oxide/zinc oxide (ZnO/IMO/ZnO) multilayer thin films are grown using pulsed laser deposition technique. The effect of substrate temperature on structural, optical, and electrical properties of multilayer films is studied. It is observed that films grown at high substrate temperature are oriented along (0 0 2) and (2 2 2) direction for ZnO and IMO respectively. The crystallinity of these films increases with increase in substrate temperature. It is also seen that conductivity, carrier concentration, and mobility increase with increase in temperature. The multilayer film grown at 500 °C has low resistivity (7.67 × 10⁻⁵ Ω cm), high carrier concentration (3.90 × 10²⁰ cm⁻³), and high mobility (209 cm²/Vs).     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Room temperature transparent conducting oxides based on zinc oxide thin films

Doped zinc oxide thin films are grown on glass substrate at room temperature under oxygen atmosphere, using pulsed laser deposition (PLD). O₂ pressure below 1 Pa leads to conductive films. A careful characterization of the film stoichiometry and microstructure using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) concludes on a decrease in crystallinity with Al and Ga additions (≤3%). The progressive loss of the (0 0 2) orientation is associated with a variation of the c parameter value as a function of the film thickness and substrate nature. ZnO:Al and ZnO:Ga thin films show a high optical transmittance (>80%) with an increase in band gap from 3.27 eV (pure ZnO) to 3.88 eV and 3.61 eV for Al and Ga doping, respectively. Optical carrier concentration, optical mobility and optical resistivity are deduced from simulation of the optical data.     

Influence of post-annealing on the properties of Sc-doped ZnO transparent conductive films deposited by radio-frequency sputtering

Sc-doped ZnO transparent conductive films are deposited on glass substrates by radio-frequency sputtering. The influence of post-annealing on the structural, morphologic, electrical, and optical properties of the films is investigated by energy dispersion X-ray spectroscopy, X-ray diffraction, Hall measurement, and optical transmission spectroscopy. The experimental results show that these films are polycrystalline with a preferred [0 0 1] orientation. The lowest resistivity of 2.6 × 10⁻⁴ Ω cm is obtained from the film annealed at 500 °C. The average optical transmittance of the films is over 90%. These results suggest that Sc-doped ZnO is a good candidate for fabricating high performance transparent conductive films.     

Characteristics of ZnO:Al thin films co-doped with hydrogen and fluorine

Fluorine and hydrogen co-doped ZnO:Al (AZO) films were prepared by radio frequency (rf) magnetron sputtering of ZnO targets containing 1 wt.% Al₂O₃ on Corning glass at substrate temperature of 150 °C with Ar/CF₄/H₂ gas mixtures, and the structural, electrical and optical properties of the as-deposited and the vacuum-annealed films were investigated. In as-deposited state, films with fairly low resistivity of 3.9-4 × 10⁻⁴ Ω cm and very low absorption coefficient below 900 cm⁻¹ when averaged in 400-800 nm could be fabricated. After vacuum-heating at 300 °C, the minimum resistivity of 2.9 × 10⁻⁴ Ω cm combined with low absorption loss in visible region, which enabled the figure of merit to uplift as high as 4 Ω⁻¹, could be obtained for vacuum-annealed film. It was shown that, unlike hydrogenated ZnO films which resulted in degradation upon heating in vacuum at moderately high temperature, films with fluorine addition could yield improved electrical properties mostly due to enhanced Hall mobility while preserving carrier concentration level. Furthermore, stability in oxidizing environment could be improved by fluorine addition, which was ascribed to the filling effect of dangling bonds at the grain boundaries. These results showed that co-doping of hydrogen and fluorine into AZO films with low Al concentration could be remarkably compatible with thin film solar cell applications.     

Investigation of p-type behavior in Ag-doped ZnO thin films by E-beam evaporation

Ag-doped ZnO (ZnO:Ag) thin films were grown on glass substrates by E-beam evaporation technique. The structural, electrical and optical properties of the films were investigated as a function of annealing temperature. The films were subjected to post annealing at different temperatures in the range of 350-650 °C in an air ambient. All the as grown and annealed films at temperature of 350 °C showed p-type conduction. The films lost p-type conduction after post annealing treatment temperature of above 350 °C, suggesting a narrow post annealing temperature window for the fabrication of p-type ZnO:Ag films. ZnO:Ag film annealed at 350 °C revealed lowest resistivity of 7.25 × 10⁻² Ω cm with hole concentration and mobility of 5.09 × 10¹⁹ cm⁻³ and 1.69 cm²/V s, respectively. Observation of a free-to-neutral-acceptor (e,A^o) and donor-acceptor-pair (DAP) emissions in the low temperature photoluminescence measurement confirms p-type conduction in the ZnO:Ag films.     

High work function of Al-doped zinc-oxide thin films as transparent conductive anodes in organic light-emitting devices

Deposition of Al-doped ZnO (AZO) films with various film thicknesses on glass substrates was performed to investigate the feasibility of using AZO films as anode electrodes in organic light-emitting devices (OLEDs). The electrical resistivity of the AZO films with a 180-nm thickness was 4.085 × 10⁻² Ω cm, and the average optical transmittance in the visible range was 80.2%. The surface work function for the AZO films, determined from the secondary electron emission coefficients obtained with a focused ion beam, was as high as 4.62 eV. These results indicate that AZO films grown on glass substrates hold promise for potential applications as anode electrodes in high-efficiency OLEDs.     

Influence of Al concentration on electrical, structural and optical properties of Al-As codoped p-ZnO thin films

We report the influence of Al concentration on electrical, structural, optical and morphological properties of Al-As codoped p-ZnO thin films using RF magnetron sputtering. Al-As codoped p-ZnO films with different Al concentrations were fabricated using As back diffusion from the GaAs substrate and sputtering Al₂O₃ mixed ZnO targets (1, 2 and 4 at%). The grown films were investigated by Hall effect measurement, X-ray diffraction (XRD), electron probe microanalysis (EPMA), energy dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and atomic force microscopy (AFM) to study the electrical, structural, optical and morphological properties of the films. From the XRD, it was observed that both full-width at half-maximum (FWHM) and c-axis lattice constant have similar trends with respect to Al concentration. Hall measurements showed that the hole concentration increases as the Al concentration increases from 10¹⁵ to 10²⁰ cm⁻³. The increase in hole concentration upon codoping was supported by the red shift in the near-band-edge (NBE) emission observed from room temperature PL spectra. The proposed p-type mechanism due to As_Zn-2V_Zn complex was confirmed by low temperature PL and XPS analysis. The low FWHM, resistivity and peak-to-valley roughness observed by XRD, Hall measurement and AFM, respectively, suggest that 1 at% Al-doped ZnO:As film is the best codoped film.     

Electrical and optical properties of ZnO films prepared by sputtering of ZnO targets containing AlN

ZnO films prepared from the ZnO target containing 2% AlN are transparent irrespective of radio frequency (RF) power. The obtained ZnO films have the carrier density of 3.8 × 10²⁰ cm⁻³ or less and the low mobility of 5.3-7.8 cm²/(V s). In the case of 5% AlN target, ZnO films prepared at 40, 60 and 80 W are transparent, whereas ZnO films prepared at 100 and 120 W are colored. As RF power increases from 40 to 120 W, the carrier density increases straightforwardly up to 5.5 × 10²⁰ cm⁻³ at 100 W and is oppositely reduced to 3.2 × 10²⁰ cm⁻³ at 120 W. In the case of 10% AlN target, ZnO films prepared at 60 W or more are colored, and have the carrier density of 4 × 10²⁰ cm⁻³ or less. The N-concentration in these colored films is estimated to be 1% or less. The Al-concentration in the ZnO films prepared from the 5 and 10% AlN targets is higher than 2%. The carrier density of the ZnO films containing Al and N atoms is nearly equal to that of ZnO films doped with Al atoms alone. There is no evidence in supporting the enhancement of the carrier density via the formation of N-Al_xZn_4−x clusters (4 ≥ x ≥ 2).     

ZnO nanorods on undoped and indium-doped ZnO thin films as a TCO layer on nonconductive glass for dye-sensitized solar cells

We present the growth of ZnO nanostructures on indium-doped ZnO film on a non-conductive glass substrate. The indium-doped ZnO film was used as the transparent conductive layer replaces the ITO layer. Various indium doping concentrations can change the electrical properties of ZnO film. The reduced electrical resistivity was investigated from 16.60 × 10⁻² to 10 × 10⁻² Ω cm. after doping with the optimal concentration of 2 wt% indium. It is found that the characteristic of ZnO nanostructures was strongly affected with indium doping concentration in ZnO films. The overall structural characteristics of ZnO ranged from 100–500 nm in size and 7–10 μm in length and the branch-like structures can be revealed from the 2 wt% indium-doped ZnO film. The room-temperature photoluminescence spectra show a sharp ultraviolet band of 353 nm, indicated to the ZnO nanorods structure. The branch-like structures on the 2 wt% indium-doped film can be yielded the photovoltaic properties with a short-circuit current density of 3.96 mA/cm², an open-circuit voltage of 0.72 V, a fill factor of 20% and an overall power conversion efficiency of 0.56% under irradiance of 100 mW/cm² (AM 1.5 G).     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

Oxygen influence on sputtered high rate ZnO:Al films from dual rotatable ceramic targets

In this study, the influence of oxygen on high rate (up to 110 nm m/min) sputtered aluminum doped zinc oxide films (ZnO:Al) was systematically investigated. Different oxygen gas flows from 0 sccm to 8 sccm were inputted into the chamber during the preparation of ZnO:Al films from dual rotatable ceramic targets under high discharge power (14 kW). The resistivity increases from 4.2 × 10⁻⁴ Ω cm to 4.3 × 10⁻² Ω cm with the rising oxygen gas flow. While both the carrier concentration and mobility drop by one order of magnitude from 3.4 × 10²⁰ cm⁻³ to 2.5 × 10¹⁹ cm⁻³ and from 43.5 cm²/V s to 5.6 cm²/V s, respectively. The as-grown ZnO:Al films and after-etched ZnO:Al films after a chemical wet etching step in diluted HCl solution (0.5%) exhibit different surface structures. All films show high light transmission and low light absorption but different light scattering properties (diffusion and haze) because of different surface structures. Moreover, ZnO:Al films display different optical bandgaps between 3.51 eV and 3.27 eV, which are corresponding to different carrier concentrations. The variation of mobility and morphology is related with chemisorption of oxygen in the grain boundaries as well as high energetic oxygen ions bombardment.     

Growth characteristics and properties of ZnO:Ga thin films prepared by pulsed DC magnetron sputtering

Transparent conductive ZnO:Ga thin films were deposited on Corning 1737 glass substrate by pulsed direct current (DC) magnetron sputtering. The effects of process parameters, namely pulse frequency and film thickness on the structural and optoelectronic properties of ZnO:Ga thin films are evaluated. It shows that highly c-axis (0 0 2) oriented polycrystalline films with good visible transparency and electrical conductivity were prepared at a pulsed frequency of 10 kHz. Increasing the film thickness also enlarged the grain size and carrier mobility which will subsequently lead to the decrease in resistivity. In summary, ZnO:Ga thin film with the lowest electrical resistivity of 2.01 × 10⁻⁴ Ω cm was obtained at a pulse frequency of 10 kHz with 500 nm in thickness. The surface RMS (root mean square) roughness of the film is 2.9 nm with visible transmittance around 86% and optical band gap of 3.83 eV.     

Synthesis, characterization of chemically deposited indium selenide thin films at room temperature

Polycrystalline In₂Se₃ semiconducting thin films were prepared by using relatively simple chemical bath deposition method at room temperature by the reaction between indium chloride, tartaric acid, hydrazine hydrate and sodium selenosulphate in an aqueous alkaline medium. Various preparative conditions of thin film deposition are outlined. The as grown films were found to be transparent, uniform, well adherent and red in color. The films were characterized using X-ray diffraction (XRD), scanning electron microscopy, atomic absorption spectroscopy and energy dispersive atomic X-ray diffraction (EDAX). The XRD analysis of the film showed the presence of polycrystalline nature with hexagonal crystal structure. SEM study revels that the grains are homogenous, without cracks or pinholes and well covers the glass substrate. The optical absorption and electrical conductivity was measured. The direct optical band gap value for the films was found to be of the order of 2.35 eV at room temperature and have specific electrical conductivity of the order of 10⁻² (Ω cm)⁻¹ showing n-type conduction mechanism. The utility of the adapted technique is discussed from the view-point of applications considering the optoelectric and structural data.     

Fabrication and vacuum annealing of transparent conductive Ga-doped Zn0.9Mg0.1O thin films prepared by pulsed laser deposition technique

In this study, highly transparent conductive Ga-doped Zn_0.9Mg_0.1O (ZMO:Ga) thin films have been deposited on glass substrates by pulsed laser deposition (PLD) technique. The effects of substrate temperature and post-deposition vacuum annealing on structural, electrical and optical properties of ZMO:Ga thin films were investigated. The properties of the films have been characterized through Hall effect, double beam spectrophotometer and X-ray diffraction. The experimental results show that the electrical resistivity of film deposited at 200 °C is 8.12 × 10⁻⁴ Ω cm, and can be further decreased to 4.74 × 10⁻⁴ Ω cm with post-deposition annealing at 400 °C for 2 h under 3 × 10⁻³ Pa. In the meantime, its band gap energy can be increased to 3.90 eV from 3.83 eV. The annealing process leads to improvement of (0 0 2) orientation, wider band gap, increased carrier concentration and blue-shift of absorption edge in the transmission spectra of ZMO:Ga thin films.     

Transparent conductive ZnO:Ga films prepared by DC reactive magnetron sputtering at low temperature

Ga-doped ZnO (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. The structural, electrical, and optical properties of ZnO:Ga films were investigated in a wide temperature range from room temperature up to 400 °C. The crystallinity and surface morphology of the films are strongly dependent on the growth temperatures, which in turn exert an influence on the electrical and optical properties of the ZnO:Ga films. The film deposited at 350 °C exhibited the relatively well crystallinity and the lowest resistivity of 3.4 × 10⁻⁴ Ω cm. More importantly, the low-resistance and high-transmittance ZnO:Ga films were also obtained at a low temperature of 150 °C by changing the sputtering powers, having acceptable properties for application as transparent conductive electrodes in LCDs and solar cells.     

Device quality ZnO grown using a Filtered Cathodic Vacuum Arc

In this paper we report on the structural, electrical and optical characteristics of unintentionally doped ZnO films grown on a-plane sapphire substrates using the Filtered Cathodic Vacuum Arc (FCVA) technique. The resulting films showed considerable promise for device applications with properties including high transparency, moderate intrinsic carrier concentrations (10¹⁷–10¹⁹ cm⁻³), electron mobilities up to 30 cm²/Vs, low surface roughness (typically <2% of film thickness) and well-structured photoluminescence. Post-annealing in oxygen at temperatures up to 800 °C produced significant improvements in the properties of these films. Silver oxide Schottky diodes fabricated on FCVA ZnO showed ideality factors as low as 1.20 and good sensitivity to ultraviolet light.