Determination of <Superscript>241</Superscript>Am/<Superscript>243</Superscript>Am ratios

Determination of ²⁴¹Am/²⁴³Am ratios is required for vanous purposes including assay of Am by isotope dilution techniques. Alpha-spectrometry on electrodeposited sources is a preferred technique for this determination. However, there is an inherent problem of tail contribution which necessitates the use of suitable algorithms to account for the same. Recently, in the frame of a Coordinated Research Program (CRP) of the International Atomic Energy Agency (IAEA), WinALPHA software has been developed which is a combination of an asymmetrical Gaussian for the main part of the peak and a low energy function. Therefore, it was of interest to compare the use of this algorithm with the routinely used method, in our laboratory, based on geometric progression (G. P.) decrease. Since, there are no reference materials available commercially for ²⁴¹Am/²⁴³Am ratios, synthetic mixtures covening a wide range (0.3 to 2.0) of ²⁴¹Am/²⁴³Am α-activity ratios were used and un-ignited electrodeposited sources were prepared for α-spectrometry. The α-spectra obtained using PIPS detector, were evaluated using the two algonthms The ²⁴¹Am/²⁴³Am α-activity ratios obtained were also compared with those determined by thermal ionization mass spectrometry (TIMS). An agreement of about 1% was obtained in the ²⁴¹Am/²⁴³Am ratios determined by the two methods and also by using the two algorithms for α-spectrum evaluation.     

<Superscript>226</Superscript>Ra and <Superscript>228</Superscript>Ra determination in environmental samples by alpha-particle spectrometry

A complete methodology for ²²⁶Ra and ²²⁸Ra determination by alpha-particle spectrometry in environmental samples is being applied in our laboratory using ²²⁵Ra as an isotopic tracer. This methodology can be considered highly suitable for the determination of these nuclides when very low absolute limits of detection need to be achieved. The ²²⁶Ra determination can be performed at any time after the isolation of the radium isotopes from the analyzed samples while the ²²⁸Ra determination needs to be carried out at least six months later through the measurement of one of its grand-daughters. The method has been validated by its application to samples with known concentrations of these Ra nuclides, and by comparison with other radiometric methods.     

Quinolinephosphomolybdate as ion exchanger: synthesis,characterization, and application in separation of <Superscript>90</Superscript>Y from <Superscript>90</Superscript>Sr

An inorganic ion exchanger, quinolinephosphomolybdate has been synthesized and characterized by elemental analysis, infrared (IR) and X-ray diffraction (XRD) spectroscopy. This compound is highly stable toward thermal, chemical and radiation dose. This has been employed in the separation of carrier-free ⁹⁰Y from its parent ⁹⁰Sr from an equilibrium mixture. The absorbed daughter was recovered by using 0.0284 mol L⁻¹ ascorbic acid solutions at pH 5.0 as eluting agent.     

Fission studies in the reaction of <Superscript>19</Superscript>F with <Superscript>209</Superscript>Bi at 99.2 MeV

Fission product yield studies in the reaction of 99.2 MeV ¹⁹F with ²⁰⁹Bi have been carried out for the first time using gamma-ray spectrometry. The cross sections for the production of fission products have been determined. The yield distribution of fission products was found to be symmetric and broad with FWHM around 22 mass units and peak near mass 111. The average number of neutrons emitted per fission has been found to be around 6.7. The comparison of the fission products yield distribution of ²⁰⁹Bi using projectiles like ⁴He, ¹²C, ¹⁶O, and ¹⁹F have shown that the mass of symmetric peak increases as the mass of the compound nucleus increases. The high fission yield around mass 112 has been attributed to the presence of deformed neutron shells. The total fission cross section and width of the mass distribution have been found to be low in case of ¹⁶O induced fission as compared to the ⁴He, ¹²C, and ¹⁹F induced fission of ²⁰⁹Bi.     

New gamma-rays in <Superscript>101</Superscript>Ru following the decay of <Superscript>101</Superscript>Tc

Summary The decay of ¹⁰¹Tc to ¹⁰¹Ru has been studied using high resulation HpGe detectors in single and coincidence mode. Technetium-101 was produced via the ⁹⁸Mo(α,p)¹⁰¹Tc reaction. The results of the present experiment verified the previously reported levels of ¹⁰¹Ru, but in addition to the known transitions and levels, the 174.91, 226.02, 312.40, 408.77, and 417.91 keV gamma-rays were observed for the first time and they were placed in the decay scheme. At the same time, the transition position of 616.3 keV gamma-ray has been assigned. For most levels the intensities of β^--decay and the values of log ft were calculated.     

Separation of <Superscript>133</Superscript>Xe from <Superscript>99</Superscript>Mo, <Superscript>131</Superscript>I and uranium,and removal of impurities using gas chromatography

Summary Separation and purification of ¹³³Xe from acidic solution containing uranium, ⁹⁹Mo and ¹³¹I has been developed. In the first step of this work, uranium pellets were dissolved under pressure (8-15 bar) in 8M nitric acid solution. Then¹³³ Xe and other gases were conducted to activated charcoal cold trap. Final purification of ¹³³Xe from impurities such as NO_x, radioiodine and krypton was performed by passing through a molecular sieve preparative chromatographic column using helium as mobile phase. The final recovery of ¹³³Xe from the separation-purification process was higher than 98%. Adsorption-desorption behavior of radioxenon on the charcoal and molecular sieves have also been studied and discussed.     

Mixing of atmospheric <Superscript>210</Superscript>Pb and <Superscript>7</Superscript>Be and <Superscript>137</Superscript>Cs and <Superscript>90</Superscript>Sr fission products in four characteristic soil types

Depth distribution of atmospheric ²¹⁰Pb and ⁷Be and ⁹⁰Sr and ¹³⁷Cs fission products was measured in two types of aeolian soils (desert dust and volcanic ash), irrigated paddy soil and strongly acidic soil. The depth dependence of ²¹⁰Pb, ⁷Be and ¹³⁷Cs show that these radionuclides have been diffused as solid soil particles in surface soil layers. In aeolian soil layers, about 50% of ⁹⁰Sr were diffused in surface soil layer and the remaining 50% had penetrated to deeper layers. The half of the fission particles containing ⁹⁰Sr were shown to have decomposed over the past 35 years.     

<Superscript>63</Superscript>Cu and <Superscript>139</Superscript>La NMR and chemical bonding in anion-deficient perovskite LACu<Subscript>0.81</Subscript>Ni<Subscript>0.19</Subscript>O<Subscript>2.5+δ</Subscript>

The ⁶³Cu and ¹³⁹La NMR spectra of the low-(δ = 0.25) and high-temperature (δ = 0) phases of lanthanum cuprate LACu_0.81Ni_0.19O_2.5+δ have been obtained. Quantum chemical calculations of the electronic structure of the high-temperature phase have been performed. It is found that the observed metal-semiconductor phase transition is attended by changes in the degree of atomic ordering and in the character of electronic conductivity over certain types of “copper” centers.     

First-principles simulations of the <Superscript>27</Superscript>Al and <Superscript>17</Superscript>O solid-state NMR spectra of the CaAl<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript> glass

The local and medium-range structure of the 20CaO·20Al₂O₃·60SiO₂ glass generated by classical molecular dynamics simulations has been compared to NMR experiments by computing the ²⁷Al and ¹⁷O NMR parameters and NMR spectra from first-principles simulations. The calculation of the NMR parameters (chemical shielding and quadrupolar parameters), which are then used to simulate solid-state MAS and 3QMAS NMR spectra, is achieved by the gauge including projector augmented-wave and the projector augmented-wave methods on the DFT-PBE relaxed structure. The NMR spectra calculated with the present approach are found to be in excellent agreement with the experimental data, providing an unambiguous view of the local and medium-range structure of aluminosilicate glasses.     

Hydrothermal synthesis,characterization, and thermal properties of alumino silicate azide sodalite,Na<Subscript>8</Subscript>[AlSiO<Subscript>4</Subscript>]<Subscript>6</Subscript>(N<Subscript>3</Subscript>)<Subscript>2</Subscript>

First time we report the synthesis, structural characterization and thermal behavior of an unusual N₃ ^? containing alumino-silicate sodalite mineral. Azide sodalite, Na₈[AlSiO₄]₆(N₃)₂ has been synthesized under hydrothermal conditions at 433 K in steel lined Teflon autoclave. The structural and microstructural properties of azide sodalite mineral was characterized by various methods including FT-IR, XRD, SEM, TGA, and MAS NMR. Crystal structure have been refined by Rietveld method in \(P\bar 43n\) space group, indicating that the N₃ ^? sodalite has cubic in lattice. High temperature study was carried out to see the effect of thermal expansion on cell dimension (a ^o) of azide sodalite. Thermal behavior of sodalite was also assessed by thermogravimetric method.     

Synthesis,DNA-binding and photocleavage studies of cobalt(III) complexes [Co(bpy)<Subscript>2</Subscript>(dpta)]<Superscript>3+</Superscript> and [Co(bpy)<Subscript>2</Subscript>(amtp)]<Superscript>3+</Superscript>

Two novel cobalt(III) mixed-polypyridyl complexes [Co(bpy)₂(dpta)]³⁺ and [Co(bpy)₂(amtp)]³⁺ (bpy = 2,2′-bipyridine, dpta = dipyrido-[3,2-a;2′,3′-c]-thien-[3,4-c]azine, amtp = 3-amino-1,2,4-triazino[5,6-f]-1,10-phenanthroline) have been synthesized and characterized. The interaction of Co^III complexes with calf thymus DNA was investigated by spectroscopic and viscosity measurements. Results suggest that the two complexes bind to DNA via an intercalative mode. Moreover, Co^III complexes have been found to promote the photocleavage of plasmid DNA pBR322 under irradiation at 365 nm. The mechanism studies reveal that hydroxyl radical (OH^•) is likely to be the reactive species responsible for the cleavage of plasmid DNA by [Co(bpy)₂(dpta)]³⁺ and superoxide anion radical (O ₂ ^•− ) acts as the key role in the cleavage reaction of plasmid DNA by [Co(bpy)₂(amtp)]³⁺.     

Electroswitchable binding of [Co(dipy)<Subscript>3</Subscript>]<Superscript>3+</Superscript> and [Fe(dipy)<Subscript>3</Subscript>]<Superscript>2+</Superscript><Emphasis Type="Italic">n</Emphasis>-sulfonato(thia)calix[4]arenas

The methods of cyclic voltammetry, electrolysis, and spectrophotometry were used to study electrochemical properties of (TCAS + Fe³⁺ + dipy), (CCAS + Fe³⁺ + dipy), and (CCAS + Fe³⁺ + [Co(dipy)₃]³⁺) triple systems (where TCAS is n-sulfonatothiacalix[4]arene, CCAS is tetracarboxylate n-sulfonatocalix[4]arene, and dipy = α,α′-dipyridyl) in an aqueous solution. One-electron reduction of Fe(III) in the (TCAS + Fe³⁺ + dipy) system at pH 2.5 results in electroswitching of iron ions from the lower TCAS ring to the upper ([Fe(dipy)₃]²⁺). Reverse electrochemical switching of the system is impossible due to mediator ([Fe(dipy)₃]^2+/3+) oxidation of TCAS. Reverse electroswitching of Fe(III) ions from unbound to bound state as ([Fe(dipy)₃]²⁺) with CCAS has been revealed in the system (CCAS + Fe³⁺ + dipy) (pH 1.7) upon single-electron transfer, whereas reversible electroswitching by the upper rim of CCAS from one complex ion ([Co(dipy)₃]³⁺) to another ([Fe(dipy)₃]²⁺) has been demonstrated in the system ([Co(dipy)₃]³⁺ + CCAS + Fe³⁺ upon double-electron transfer. In all systems, electric switching was accompanied by synchronous color switching.     

Physicochemical foundations of synthesis of new ferromagnets from chalcopyrites A<Superscript>II</Superscript>B<Superscript>IV</Superscript>C<Stack><Subscript>2</Subscript><Superscript>V</Superscript></Stack>

The results of studying phase equilibria of ternary A^IIB^IVC^V systems have been reported. Physicochemical foundations have been developed for the synthesis of new ferromagnets with Curie temperatures above room temperature structurally compatible with basic semiconducting materials. Methods of synthesis and physicochemical properties of manganese-doped A^IIB^IVC₂^V ferromagnets have been described. The results of theoretical simulation of magnetic properties have been considered and basic approaches to the explanation of the emergence of ferromagnetism in A^IIB^IVC₂^V doped with 3d metals have been surveyed. The most promising ways to produce and study dilute magnetic semiconductors as spintronics materials have been presented.     

A novel electrochemical <Superscript>99</Superscript>Mo/<Superscript>99m</Superscript>Tc generator

A novel electrochemical process to avail clinical grade ^99mTc from (n,γ)⁹⁹Mo has been demonstrated. The electrochemical parameters were optimized to maximize the ^99mTc yield with minimal ⁹⁹Mo contamination. ⁹⁹Mo/^99mTc generators containing up to 29.6 GBq (800 mCi) ⁹⁹Mo were developed and their performance were extensively evaluated for 10 days without changing the operating conditions. Very high radioactive concentration of ^99mTcO₄ ⁻ of acceptable quality, commensurate with hospital radiopharmacy requirements could be availed from the system with >90% yield. The compatibility of the product for the formulation of ^99mTc labeled radiopharmaceuticals such as ^99mTc-DMSA and ^99mTc-EC was found to be satisfactory in terms of high labeling yields. The proposed route represents an important step for enhancing the scope of accessing clinical grade ^99mTc from low specific activity (n, γ)⁹⁹Mo.     

Preparation of <Superscript>26</Superscript>Al, <Superscript>59</Superscript>Ni, <Superscript>44</Superscript>Ti, <Superscript>53</Superscript>Mn and <Superscript>60</Superscript>Fe from a proton irradiated copper beam dump

The station for pions cancer therapy was operated at PSI from 1980 to 1992. After a cooling time of 12 years it’s made of copper beam dump was cut and samples were taken for analytical purposes. The sampling collected about 500 g of high active copper chips that can be used for separation of exotic radionuclides. The analyses by gamma spectrometry, LSC and AMS showed main nuclides present to be ⁶⁰Co, ⁵⁴Mn, ²²Na, ⁶⁵Zn, ²⁶Al, ⁵³Mn, ⁵⁹Ni, ⁶³Ni, ⁵⁵Fe and ⁶⁰Fe and ⁴⁴Ti with a daughter nuclide ⁴⁴Sc. In the frame of ERAWAST project a procedure combining selective precipitation and ion exchange for the separation of the rare radionuclides from the copper beam dump was developed. The proposed separation procedure is easy for remote controlled implementation in a hot cell. The ion exchange separation of Ni, Al, Mg, Ti and Fe was complete and high decontamination factors for copper and cobalt were achieved. Based on the developed procedure a remotely controlled system for separation of exotic radionuclides from the copper chips was set up. The full scale system was installed in a hot cell where high activity levels can be handled. In order to evaluate the reliability and functionality of the system extensive tests have been done. During the test period 13.86 g in total of the proton irradiated copper beam dump were processed for separation of ²⁶Al, ⁵⁹Ni, ⁵³Mn, ⁴⁴Ti and ⁶⁰Fe. The results showed that the system was operational and the radionuclide separation was selective with high chemical yield. The procedure manages as well the generated liquid wastes containing high level of ⁶⁰Co activity.     

Sequential separation of <Superscript>99</Superscript>Tc, <Superscript>94</Superscript>Nb, <Superscript>55</Superscript>Fe, <Superscript>90</Superscript>Sr and <Superscript>59/63</Superscript>Ni from radioactive wastes

A sequential separation procedure has been developed for the determination of ⁹⁹Tc, ⁹⁴Nb, ⁵⁵Fe, ⁹⁰Sr and ^59/63Ni in various radioactive wastes generated from nuclear power plants. Ion exchange and extraction chromatography were adopted for individual separation of the radionuclides. Precipitation was supplementarily utilized for both purification of the individual radionuclides and preparation of the radionuclide sources for use in a radioactivity measurement. The chromatographic separation behavior of the radionuclides both from the sample matrix metals and from one another was investigated using stable metals, Re (as a surrogate of ⁹⁹Tc), Nb, Fe, Sr and Ni. The validity of the procedure for reliability and applicability was evaluated by measuring the recovery of the metal carriers added to synthetic radioactive waste solutions. The recoveries by the chromatographic separation were in the range of 84.8 to 102.2% with 2s of less than 8.6%, the recoveries by the precipitation being in the range of 84.3 to 97.3% with 2s of less than 10.9%.     

Production of <Superscript>41</Superscript>Ar and <Superscript>79</Superscript>Kr gaseous radiotracers for industrial applications

Radiotracers are extensively used in many industries for trouble shooting and optimization of process parameters leading to considerable savings in time and huge economic benefits. In chemical and petrochemical industries different gases and vapours flowing in the conversion reactors play a major role in the final production. Gaseous radiotracers are ideal to study hydrodynamics of gas phases in process vessels. ⁴¹Ar and ⁷⁹Kr are the preferred gaseous radiotracers for such studies. Owing to the increase in demand from Indian industries for gas phase radiotracers, efforts have been made to produce ⁴¹Ar and ⁷⁹Kr indigenously by irradiation of ⁴⁰Ar and enriched ⁷⁸Kr gaseous targets in research reactors. Prequalification of the containers used, safety aspects concerning accidental rupture and mandatory tests necessary for irradiation of gaseous targets in the reactors have been studied. The paper describes some of the important safety aspects involved and the results of trial irradiations on the production of ⁴¹Ar and ⁷⁹Kr radiotracers. Standardization of suitable assay protocols for their regular production and supply for applications in industries is also described.     

Synthesis and crystal structure of [Co(NH<Subscript>3</Subscript>)<Subscript>6</Subscript>][AuX<Subscript>4</Subscript>]X<Subscript>2</Subscript> (X = Cl<Superscript>−</Superscript>, Br<Superscript>−</Superscript>)

[Co(NH₃)₆][AuX₄]X₂ binary complex salts, where X = Cl^? (I) and Br^? (II), have been obtained and defined by element, X-ray diffraction, and thermal analyses and by IR, Raman, and electron spectroscopy. The compounds are isostructural. Their structural units are the [Co(NH₃)₆]³⁺ complex cations, the [AuX₄]^? complex anions, and the X^? anions. The plane square environment of the gold atom is completed to an elongated bipyramid by two halide ions lying at distances Au...Cl 3.245 Å for I and Au...Br 3.362 Å for II. The thermolysis products of I and II are pure gold and cobalt metal powders when thermolysis is performed under hydrogen and a mixture of metallic gold with cobalt halide in a reaction under an inert atmosphere.     

Chemometrics of the distribution and origin of <Superscript>226</Superscript>Ra, <Superscript>228</Superscript>Ra, <Superscript>40</Superscript>K and <Superscript>137</Superscript>Cs in plants near the West Macedonia Lignite Center (Greece)

Summary The distribution and origin of ⁴⁰K, ²²⁶Ra, ²²⁸Ra and ¹³⁷Cs has been investigated in trees, mosses and lichens in the basin of the West Macedonia Lignite Centre. In tree leaves ¹³⁷Cs is negligible, while the ²²⁶Ra and ²²⁸Ra concentrations are affected by the fly ash particles. Concerning ²²⁶Ra and ²²⁸Ra values of mosses and lichens, which are systematically larger than those of unpolluted areas, the application of chemometrics proved that they originate mainly from the lignite fly ash.     

New framework nanostructures of carbon atoms in <Emphasis Type="Italic">sp</Emphasis><Superscript>2</Superscript> and <Emphasis Type="Italic">sp</Emphasis><Superscript>3</Superscript> hybridized states

A new family of framework nanostructures including carbon atoms in _sp ² and sp ³ hybridized states is reported. Structure optimization was fulfilled using MM+ molecular mechanics and Hückel semiempirical methods. The energy characteristics of the structures have been evaluated. Comparative analysis of the stability of the title nanostructures has been performed in relation to their geometry and relative contents of sp ²/sp ³ atoms.