Lead Zirconate-Titanate Films Prepared from Soluble Powders

Precursor powders for Pb(Zr1 – xTix) O3 (PZT) thin films were produced by the reaction of zirconium-and titanium-n-propoxides with acetylacetone and lead acetate trihydrate. The subsequent complete removal of volatile components yielded powders that can be handled in air. The powders are indefinitely stable under ambient conditions.High molarity (>2m) coating sols were prepared by dissolution of the precursor powders in mixtures of 1,3-propanediol, triethanolamine (TEA) and water. Excess amounts of lead to compensate lead loss during firing were easily introduced into these solutions.The deposition of these sols on steel substrates and firing at 600°C yielded PZT films. Many physical parameters like film thickness, morphology and electrical performance could be influenced by choice of the solvent mixture composition and oxide content of the sols. Depending on the preparation dielectric permittivities, r of up to 840 were measured at 1 kHz. By hysteresis measurements at 50 Hz and a field amplitude of 50 V/m a remanent polarization of about 40 C/cm2 and coercivity of about 8 V/m was obtained. The films were stable against dielectric breakdown up to 70V/m.     

Preparation of PZT Thick Films by an Interfacial Polymerization Method

Pb(Zr_0.53Ti_0.47)O₃ (PZT) films of 10 to 50 m in thickness were prepared by a new sol-gel process using an interfacial polymerization technique. The interfacial polymerization process is that an alkoxide precursor solution is poured on the surface of water in a container to form a gel film at the interface between the two immiscible liquids. The precursor solution was prepared by adding PZT alkoxide solution, PZT powders coated with Pb₅Ge₃O₁₁ (PG), and a surfactant into hexane solvent. After the polymerization at the interface, the gel films were gently placed on a silicon substrate by draining the water in the container. The gel films containing PZT powders were sintered at 950°C for 10 min to obtain crystallized PZT films. The remanent polarization of a PZT thick film was 33.1 C/cm². The piezoelectric d ₃₃ constant measured with a Mach-Zehnder interferometer was 225 pm/V and was independent of frequency from 0.2 to 3 kHz.     

Crystallization Behavior of Sol-Gel Derived Films by Self-Seeding Process

We propose the novel preparation method, Self-seeding Process, based on the following concept for low temperature crystallization of oxide films. Introduction of desirable inhomogeneity should give lowering of a crystallization temperature through heterogeneous nucleation accompanied with reduced activation energy. We carried out inspection of the above concept through use of PZT films. PZT gel films with the desirable inhomogeneity of microstructure were prepared, and their crystallization behaviors was examined. The PZT film was successfully crystallized at 500°C by the self-seeding process. The single phase (001) oriented PZT film with 0.55 m in thickness was obtained at 550°C for 5 min. The self-seeding process by microstructure control is efficient for the low temperature process of the oxide thin film.     

Optical Nanocomposite Planar Waveguides Doped with Rare-Earth and Noble Metal Elements

The present paper is focused on multilayer Er³⁺-doped silica-titania planar waveguides, co-doped with silver, which were prepared by spin-coating on silica glass, or buffered single crystal silicon substrates. The single layer thickness (0.4 m) and refractive index (1.60–1.63) were measured by spectroscopic ellipsometry at 715 nm. The thickness of the waveguides (measured by mechanical profilometry) was 1 m and their optical propagation losses were measured at different laser wavelengths (488 nm, 514 nm and 633 nm), exhibiting an approximately Rayleigh-like behavior. The thermal precipitation of silver nanocrystallites was achieved, both in air and under a controlled atmosphere (dry nitrogen) and these were characterized by visible absorption spectroscopy, which clearly showed the development of a plasmon absorption band near 415 nm, by X-ray diffraction (XRD) and Transmission Electron Microscopy (TEM). The Er³⁺ metastable level lifetimes for the emission at ca. 1.54 m were found to be ca. 4–6 ms, for Er³⁺ concentrations varying between 0.2–2.0 mol% (or (0.4–4.4) × 10²⁰ ions/cm³), but no significant variation was observed with the Ag concentration added (up to 2.5 mol%).     

Theoretical Investigation of Transparent (3–5 μm) and High Reflective (1.3 μm) Filter by Sol-Gel Process

When designing a cut-off interference filter, extra layers are needed to add on each side of periodic symmetrical multilayer to match the incident medium and the substrate. In this paper, we use sol-gel film with adjustable refractive index as the match layer. The influence of the refractive index and thickness of the match layer on the film system is discussed in detail. As an example, a special filter which is transparent (>80%) at the wavelength 3–5 m and high reflective (>90%) at the wavelength 1.3 m is designed. Finally a series of optimized film parameters are presented. The whole design process is a good reference to the other multilayer special filter made by sol-gel process.     

Sol-Gel Fabrication and Properties of Silica Cores of Optical Fibers Doped with Yb3+, Er3+, Al2 O3 or TiO2

Optical cores of preforms for drawing optical fibers doped with Er3+ and Yb3+ were fabricated by the sol-gel method with the aim of increasing the thickness of glass layers coated in a single coating cycle and to determine the relation between the preparation conditions and optical properties of the fibers. Al2O3-P2O5-SiO2 and TiO2-P2O5-SiO2 glasses have been studied as matrices for entrapping the rare-earth elements. Input sols have been prepared from silicon and titanium alkoxides, AlCl3, ErCl3, YbCl3, POCl3, water and a modifier under acidic catalysis of HCl. The sols were coated on the inner wall of a silica substrate tube and the gel layers were sintered at high temperatures up to 2000°C after which the tube was collapsed into the preform. Continuous and homogenous glass films with the maximum thickness of about 8 m were fabricated. The influence of high-temperature heat treatment of the layers on their composition and optical attenuation was observed. The amplified stimulated emission of Er3+ around 1.55 m was measured under the excitation of the fibers by an Nd : YAG laser at 1.064 m.     

Determination of traces of sodium alkylbenzenesulphonate by high-performance liquid chromatography. Application to water

Summary For the trace determination of sodium alkylbenzenesulphonate (ABS) by HPLC the following conditions were employed: Shimadzu ZORBAX SIL Column (5 m, 4.6 mm i.d. x 150 mm) as stationary phase, 0.2% ammoniaethanol (v/v) as mobile phase, UV detector at 225 nm, injection volume 12 l. The chromatograms of ABS were simple and sharp (detection limit of ABS 0.02 g in 12 l of ethanol). The calibration curves of ABS were linear in a concentration range of 0.03 0.3 g in 12 l of ethanol. In the case of linear sodium dodecylbenzenesulphonate positive errors of 1 4% were caused by non-ionic surfactants or laurylsulphate (6 times excess), 10 50% positive errors were caused by 2 6 times excess of household detergents.Standard water samples containing ABS were treated with a weak base anion-exchange resin, the adsorbed ABS were eluted, and then determined either by HPLC or by the methylene blue spectrophotometric method. Recoveries of ABS in water were about 92 107% by HPLC.

---

Bestimmung von Spuren Natriumalkylbenzolsulfonat mit Hilfe der HPLC. Anwendung auf Wasser

Zusammenfassung Für die Spurenbestimmung von Natriumalkylbenzolsulfonat (ABS) durch HPLC werden die folgenden Bedingungen empfohlen:Shimadzu ZORBAX SIL (5 m, 4,6 mm x 150 mm) als stationäre Phase, 0,2% Ammoniak/Ethanol als mobile Phase, UV-Detektor bei 225 nm, Injektionsvolumen 12 l. Die erhaltenen Chromatogramme sind einfach und scharf (Nachweisgrenze 0,02 g in 12 ml Ethanol). Die Eichkurven sind im Konzentrationsbereich von 0,03–0,3 g in 12 l Ethanol linear. Im Falle des linearen Natriumdodecylbenzolsulfonats werden bei Anwesenheit von nicht-ionischen oberflächenaktiven Substanzen oder von Laurylsulfat in 6fachem Überschuß positiver Fehler von 1–4% erhalten; bei 2–6fachem Überschuß von Haushaltswaschmitteln ergeben sich positive Fehler von 10–50%.Standard-Wasserproben werden zunächst einer Behandlung mit einem Anionenaustauscher unterzogen, die adsorbierten ABS eluiert und durch HPLC oder nach der Methylenblaumethode analysiert. Wiederfindungsraten liegen bei 92–107%.

     

Differential pulse voltammetric methods for the simultaneous estimation of uranium-iron and uranium-cadmium mixtures in solution

Differential pulse voltammetric methods have been developed for the simultaneous estimation of the constituents of uranium-iron and uranium-cadmium mixtures in solution. A mixture of 1M H₃PO₄–1M KH₂PO₄ (with a pH1.5), was found to be the most ideal supporting electrolyte for both methods, among many that were evaluated for their suitability. In uranium-iron mixtures the calibration for iron was found to be linear up to 150 g ml^–1 (r²=0.9986), while that of uranium up to 500 g ml^–1 (r²=0.999). Iron at 6.7 g ml^–1 level could be determined in the presence of 800 fold uranium (wt/wt) without significant interference. Uranium at 21 g ml^–1 level could be analyzed with 5-fold iron (wt/wt). This upper limit of iron was due to the precipitation of iron as phosphate. In the case of uranium — cadmium mixtures, cadmium calibration for cadmium was found to be linear up to 1300 g ml^–1 (r²=0.9993). Concentration levels of 4.6 g ml^–1 Cd could be determined at a 500-fold excess (wt/wt) of uranium. Uranium calibration was linear up to 500 g ml^–1 (r²=0.999) and 21 g ml^–1 uranium could tolerate up to a 1000-fold excess of cadmium (wt/wt). Both procedures could tolerate 10 g ml^–1 levels of metal ions, such as chromium, copper, manganese, molybdenum and vanadium.     

Hydrogen profiling in thin films using coincident ERD

By using the coincident measurement, an ERD method has been established and used for hydrogen profiling in thin foils. In the present study, 6 MeV has been used as incident particle, the scattered and the recoiled proton from one collision were coincidentally detected at 150 (proton) and 173.9 (). This method has been used for hydrogen profiling of 5.6 m Mylar and 8.6 m aluminium foils. Because of the coincident measurement, the background is largely reduced, and its minimum detection limit is about 0.5% (atomic), lower than the conventional ERD method. The measured depth resolution in 5.6 m Mylar is 0.6 m. It is possible to use this method for hydrogen profiling in thin foils of several micron thickness.     

Characteristics of Diffraction Gratings Fabricated by the Two-Beam Interference Method Using Photosensitive Hybrid Gel Films

Diffraction gratings of arbitrary periods have been fabricated by the two-beam interference method using photosensitive ZrO₂ gel films and characterized. The ZrO₂ gel films were formed on Si or silica glass substrates from sols that were derived from Zr-butoxide modified chemically with benzoylacetone. The gel films were irradiated with two interference beams from a He-Cd laser (325 nm) and then leached in ethyl alcohol. The above process gave uniform surface-relief gratings of periods ranging from 1.0 to 0.5 m, depending on the incidence angle of the interference beams. The diffraction efficiency, measured in the Littrow configuration using a He-Ne laser (633 nm), showed polarization dependence for the grating of 0.5 m period but not for the gratings of 1.0 m period. The maximum diffraction efficiency was 18% for the grating of 1.0 m period and 28% for that of 0.5 m period in the reflection mode. The present study has proved that the photosensitive gel films are versatile in fabrication of optical devices.     

Measurements of the capacitance and the response time of solid-state potentiometric sensors by an electrochemical time-of-flight method

A micro-electrochemical time-of-flight technique relying on galvanostatic ion generation and potentiometric sensing (P-ETOF) has been developed in order to characterize dynamic properties of solid-state potentiometric sensors and to measure their capacitance. Lithographically-fabricated generator-sensor devices featuring 10 m-wide micro-electrodes spaced by 20–50 m are used in either an open face mode, where hemi-cylindrical diffusion governs mass transport of generated ions, or in a narrow channel mode, where linear diffusion describes transport of ions between the generator and sensor micro-electrodes in a thin (~3 m) layer of electrolyte. P-ETOF-open face mode is capable of generating silver ions or protons at a rate equivalent to a current density of 10 A/cm². This induces a maximum, mass transport controlled rate of a sensor potential rise of ~80 V/s. P-ETOF was used to characterize anodically electrodeposited iridium oxide film pH micro-sensors. Their maximum rate of potential change was determined to depend inversely on the oxide films thickness and varied from 34 V/s for 40 nm-thick films to 9 V/s for the 650 nm-thick iridium oxide films. The capacitances of these pH micro-sensors were determined to depend linearly on their thicknesses, with a slope of 3 F cm^–2 nm^–1 and a specific capacitance of 30 F/cm³. These results point to slow proton transport in the bulk of the oxide film as a mechanistic element of their pH response.Dedicated to Zbigniew Galus on the occasion of his 70th birthday.     

Applications of the small spot ESCA system SSX 100 in surface analysis

Summary Evidence is presented that old ESCA limitations and restrictions (e.g. big X-ray beam diameter or small unrealistic size of samples) are not valid any longer. The new SSX 100 ESCA spectrometer with its unique combination of ESCA innovations (focusing monochromator, parallel imaging detectors, high throughput electron optics and improved sample handling) makes solving surface problems much easier. Two applications on semiconductors and insulators using the small spot X-ray beam (diameter: 150 m) demonstrate that small spot ESCA technique now can be applied on problems which could not be solved with conventional ESCA technique hitherto.

---

Anwendungsbeispiele vom fein-fokussierenden ESCA-System SSX 100 in der Oberflächenanalytik

Zusammenfassung Es wird gezeigt, daß bisherige Limitierungen und Restriktionen in der Anwendung der ESCA-Technik (z.B. der relativ große Strahldurchmesser oder die kleine unrealistische Probengröße) nicht länger gültig sind. Das neue SSX 100 ESCA-System hilft bei der Lösung von Oberflächenproblemen ganz erheblich aufgrund seiner einzigartigen Kombination von sinnvollen und hilfreichen Innovationen (z.B. fokussierender Monochromator, parallel abbildender Detektor, effektive Elektronenoptik und ver besserte Probenhandhabung). Zwei Anwendungen bei Halbleitern und Isolatoren unter Benutzung des feinfokussierten Röntgenstrahls (Durchmesser: 150 m) zeigen, daß die small spot ESCA-Technik jetzt erfolgreich bei Problemen angewandt werden kann, die bisher mit konventionellem ESCA nicht zu lösen waren.

     

Determination of sulphathiazole in the presence of sulphametazine by first-derivative solid-phase spectrophotometry

Sulphathiazole in the presence of sulphametazine is determined by a method based on derivative solid-phase spectrophotometry. Both compounds are fixed on a dextran-type cation-exchange gel. The absorbance of the gel, packed in a 1-mm silica cell, is measured directly. The range of application is between 0.20 and 18.0 g/ml of sulphathiazole in the presence of up to 20 g/ml of sulphametazine, the relative standard deviation is 0.6% and the detection limit is 0.05 g/ml. The method has been applied to the determination of sulphathiazole in synthetic mixtures and pharmaceuticals, with recoveries of 95.0 to 102.5%     

Preparation and Properties of Nb-Coated Barium Titanate Composite Particles by Surface Modification with Nb Alkoxide in Hydrophobic Solvent

Chemical processing for the preparation of Nb-coated barium titanate composite particles was investigated using surface modification technology, hydrolyzing Nb ethoxide on the surface of barium titanate particles dispersed in hydrophobic solvent.It was confirmed from the measurements of specific surface area and zeta potential as well as SEM, TEM and EDX observations of the resulting composite particles that the original barium titanate particles were coated uniformly with hydrolysis product of Nb ethoxide.Barium titanates coated with 1 wt% of Nb as oxide were well sintered at 1200–1300°C. The dielectric constants of the sintered barium titanates showed flattened temperature dependence, but it depended upon the average particle size of original barium titanate. The sintered bodies of Nb-coated barium titanate powders with average particle size of 0.2 m gave dielectric constants of 2000–3000 and those of barium titanate with average particle size of 0.5 m showed dielectric constants of 3000–4000 at room temperature.The microstructure of the sintered barium titanate coated with Nb oxide consisted of grains of about 1 m, smaller than those of sintered original barium titanate.     

Certified reference materials (CRM 408 and 409) for quality control of main components (ammonium, calcium, hydronium, magnesium, nitrate, potassium, sodium and sulphate) in simulated rain water

Analyses of rainwater are routinely performed by a number of organisations to monitor the contribution from rainwater to the component occurrences in the environment and the acidification of the environment. To control the quality of such determinations, the Community Bureau of Reference (BCR) has organised a certification campaign to produce two simulated rainwater reference materials (CRM 408, low mineral content and CRM 409, high mineral content). The materials were carefully prepared (addition of pro analysis and supra pure reagents with the mentioned elements to silica-free deionised water) and its homogeneity and long-term stability were verified. The materials were certified for their contents of ammonium (106 mol/kg) (CRM 409), calcium (7.68 and 15.5 mol/kg), chloride (67.3 and 113 mol/kg), hydronium (16.6 and 48.0 mol/kg), magnesium (6.14 and 12.3 mol/kg), nitrate (20.1 and 78.1 mol/kg), potassium (4.25 mol/kg) (CRM 409), sodium (42.0 and 82.9 mol/kg) and sulphate (10.5 and 53.2 mol/kg). Indicative values (not certified) are given for ammonium and potassium in CRM 408. This paper presents the certification work performed, as well as the analytical work for the certification of the contents of relevant species.     

Chemical behaviour of helium muonide just after muon catalyzed fusion

Chemical behaviour of a helium muonide atom /He^o/ can be understood on the analogy of its hydrogen homologues, muonium /Mu/, deuterium /D^o/ and tritium /T^o/. In muon catalyzed fusion /CF/, a small fraction of negative muon in the fusion cycle sticks to helium to give proton-like He⁺ which easily picks up one electron forming He^o. The energy of He⁺ at birth is about 3.5 MeV being in a similar situation to the case of a hot tritium atom produced by /n, p/ or /n, / reaction. The reaction cross section and rate of He^o reactions are estimated.     

Basic condensation of triphenylsilane. II. Kinetics in anhydrous isopropanol and influence of silanol

Condensation of triphenylsilane with isopropanol in presence of isopropoxide has been studied in anhydrous medium and the activation parameters have been measured. Dehydration of the medium has been obtained by means of a pre-reaction of triphenylsilane with the residual water in the solvent. In this medium the reaction is extremely slow, moreover, it is inhibited by silanol whose effect would lower the actual catalyst concentration.

---

. . , .

     

Size spectra for trace elements in urban aerosol particles by instrumental neutron activation analysis

Size-fractionated aerosol samples collected with micro-orifice impactors at Camden, NJ, a heavily industrialized urban area, and at two sites near Washington, DC, were analyzed for elemental constituents determined instrumentally from short-lived neutron activation products. A least-squares peak-fitting method was used with impactor calibration data to determine log-normal distribution parameters, i.e., mass median aerodynamic diameter (MMAD) and geometric standard deviation (_g) for particles bearing S, V, Br, and I. For these elements, MMADs ranged from 0.24 to 0.65 m; 0.23 to 0.53 m; 0.22 to 0.61 m, and 0.20 to 0.48 m, respectively.     

Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.