Phase behaviour and superionic phase transition in K<Subscript>3</Subscript>H(SeO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The phase behaviour of K₃H(SeO₄)₂ (TKHSe) above room temperature has been studied by differential scanning calorimetric (DSC), thermogravimetric analysis (TGA), simultaneous thermogravimetric and mass spectroscopy analysis (TG-MS), impedance spectroscopy (IS) and X-ray powder diffraction (XRD). Our results show that the previously claimed superionic phase transition in TKHSe at around 388 K (114.85 °C) is also the onset temperature of a slow thermal dehydration that occurs at reaction sites distributed over the surface of the crystal. That is, we propose that the TKHSe undergoes simultaneously a superionic phase transition and a decomposition process with a very slow reaction rate that is evident when the sample is pulverized to fine powder, both starting at the same temperature. As a matter of fact, we observe a decrease of the magnitude of the dc-conductivity on successive thermal runs in powdered sample attributed to sample decomposition that starts at the surface of the TKHSe grains, but the jump in conductivity is only a consequence of the order–disorder transition in the TKHSe phase that remains inside the grains.     

Mechanism of thermal decomposition of the nonstoichiometric compound YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>6.8</Subscript>

Thermal decomposition of the nonstoichiometric high-temperature superconductor YBa₂Cu₃O_6.8 at a temperature of 200°C in air has been investigated using the full-profile analysis of X-ray diffraction lines. Two mechanisms of decomposition are revealed. The first mechanism, i.e., separation into two phases with a different oxygen content, occurs continuously. The second mechanism, i.e., disordering of the heavy atoms Y, Ba, Ba, Y along the crystallographic axis c, begins to occur after a 20- to 35-h annealing and progresses with a further annealing.     

Genesis,structural, and transport properties of La<Subscript>2</Subscript>Mo<Subscript>2-x</Subscript>W<Subscript>x</Subscript>O<Subscript>9</Subscript> prepared via mechanochemical activation

Fast oxide-ion conductors La₂Mo_2-xW_xO₉ (x = 0–1) have been prepared using mechanochemical activation (MA) of starting oxides in a high-power planetary ball mill. Studies of La₂Mo_2-xW_xO₉ genesis and structural properties using thermal analysis, XRD, SEM, IR, and Raman spectroscopy have revealed that MA results in the formation of an amorphous precursor, while the cubic β-phase is formed after calcination at 700–900 °C. Due to a high dispersion of powders, high-density pellets of W-LAMOX ceramics have been obtained already after sintering at 950 °C. Their electrical conductivity measured by the impedance spectroscopy depends on the W concentration being sufficiently high (up to 5.6?10^?3 S/cm at 630 °C) at temperatures below 650 °C.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Electrophysical properties and the structure of the YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> compound thermally restored after low-temperature decomposition

The electrophysical properties and structure of the nonstoichiometric high-temperature superconductor YBa₂Cu₃O _y restored at T = 930–950°C after low-temperature decomposition (T = 200°C) into phases different in the oxygen content have been studied. It has been shown that, unlike heat treatments at T ≤ 900°C, the superconducting properties are almost completely restored for 3–5 h during grain recrystallization, which is impossible at lower temperatures. After short-term annealing at T = 930–950°C (for 1–2 h), the ceramic material still contains a significant number of structural defects, most likely, in cation sublattices. These defects can contribute to the pinning of magnetic vortices, which substantially increases the critical current density in magnetic fields up to 2 T as compared to ceramic materials produced by the conventional technology.     

Temperature dependent surface and spectral modifications of nano V<Subscript>2</Subscript>O<Subscript>5</Subscript> films

Nanocrystalline V₂O₅ films have been deposited on glass substrates at 300°C substrate temperature using thermal evaporation technique and were subjected to thermal annealing at different temperatures 350, 400, and 550°C. X-ray diffraction (XRD) spectra exhibit sharper and broader characteristic peaks respectively indicating the rearrangement of nanocrystallite phases with annealing temperatures. Other phases of vanadium oxides started emerging with the rise in annealing temperature and the sample converted completely to VO₂ (B) phase at 550°C annealing. FESEM images showed an increase in crystallite size with 350 and 400°C annealing temperatures followed by a decrease in crystallite size for the sample annealed at 550°C. Transmission spectra showed an initial redshift of the fundamental band edge with 350 and 400°C while a blue shift for the sample annealed at 550°C, which was in agreement with XRD and SEM results. The films exhibited smart window properties as well as nanorod growth at specific annealing temperatures. Apart from showing the PL and defect related peaks, PL studies also supported the observations made in the transmission spectra.     

Mechanisms of interaction of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript> <Emphasis Type="Italic">y</Emphasis> </Subscript> with water vapor at low-temperature annealing

Abstract—The interaction of YBa₂Cu₃O_y (123) with water vapor at temperatures T ≤ 150° has been studied. It has been shown that, with an increase in temperature, the mechanism of its interaction with water changes. Near room temperature, the main process is hydrolytic decomposition. At T ~ 100°C, the absorption of water is significantly reduced, because the role of hydrolysis becomes less important and water penetrates the structure weakly and is incorporated into oxygen vacancies mainly in the form of OH–-groups, which leads to the transition of YBa₂Cu₃O_y from the tetragonal to orthorhombic phase. With an increase in temperature to 150°C, the absorption of water increases again. In this case, the main mechanism is the penetration of water to the 123 structure, which leads to splitting of Cu–O chains and a phase transition from the 123 to pseudo-124 structure. The role of different mechanisms of interaction with water essentially depends on the oxygen content in the 123 structure. At a low oxygen index (y = 6.3), the role of hydrolysis is more important, and, at y ≥ 6.5, the incorporation of water into the structure prevails. It has been revealed that, at T = 150°C, after absorption of water, YBa₂Cu₃O_6.96 becomes a proton conductor.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

Mechanism of thermal decomposition of K<Subscript>2</Subscript>FeO<Subscript>4</Subscript> and BaFeO<Subscript>4</Subscript>: A review

This paper presents thermal decomposition of potassium ferrate(VI) (K₂FeO₄) and barium ferrate(VI) (BaFeO₄) in air and nitrogen atmosphere. Mössbauer spectroscopy and nuclear forward scattering (NFS) synchrotron radiation approaches are reviewed to advance understanding of electron-transfer processes involved in reduction of ferrate(VI) to Fe(III) phases. Direct evidences of Fe ^V and Fe ^IV as intermediate iron species using the applied techniques are given. Thermal decomposition of K₂FeO₄ involved Fe ^V, Fe ^IV, and K₃FeO₃ as intermediate species while BaFeO₃ (i.e. Fe ^IV) was the only intermediate species during the decomposition of BaFeO₄. Nature of ferrite species, formed as final Fe(III) species, of thermal decomposition of K₂FeO₄ and BaFeO₄ under different conditions are evaluated. Steps of the mechanisms of thermal decomposition of ferrate(VI), which reasonably explained experimental observations of applied approaches in conjunction with thermal and surface techniques, are summarized.     

Fabrication and electrochemical performance of La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>CoO<Subscript>3</Subscript> impregnated porous YSZ cathode

La_0.5Sr_0.5CoO₃-yttria-stabilized zirconia (LSCO-YSZ) composite cathode for solid oxide fuel cell (SOFC) has been fabricated by wet impregnation method. Nitrate precursors of La, Sr, and Co have been impregnated into the pre-sintered porous YSZ matrix, which is converted into LSCO phase after calcination at 850 °C in the presence of glycine as confirmed from X-ray diffraction. LSCO of 5, 7, and 10 wt% impregnated porous YSZ have been electrochemically characterized using 2-probe AC conductivity method. Maximum ionic conductivity of 0.27 S/cm at 800 °C and activation energy of 0.15 eV between 600 and 800 °C have been observed for 10 wt% LSCO-YSZ cathode. Area-specific resistance of 1.01 Ω cm² at 800 °C is estimated for the electrolyte-supported half-cell (10 wt% LSCO-YSZ/YSZ). After testing the LSCO-YSZ cathode matrix, the electrolyte-supported full cell (10 wt% LSCO-YSZ/YSZ/NiO-YSZ) has been tested and produced maximum power density 51.12 mW/cm² (109.38 mA/cm²) at 800 °C. The electrolyte-supported full cell exhibited 6 Ω cm² electrode polarization at 800 °C in H₂, which is in higher side leading to low performance. LSCO-YSZ/YSZ/NiO-YSZ SOFC found to give stable performance up to 2 h and scanning electron microscopy analysis has been carried out before and after cell testing to assess the morphological changes.     

Influence of K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> on dielectric and barrier properties of polymer

Polymer composite comprising polyvinylidene fluoride (PVDF) and potassium hexatitante (K₂Ti₆O₁₃) was synthesized by solution casting. The effect of K₂Ti₆O₁₃ on surface, thermal, and electrical properties of polymer composite were investigated. The addition of K₂Ti₆O₁₃ with polymer leads to thermal degradation and transition of polymer composite from semi-crystalline to amorphous phase. The optimum results of contact angle for different loading wt% of K₂Ti₆O₁₃ were directly correlated with the surface morphology. Our experimental results confirmed the incorporation of K₂Ti₆O₁₃ in polymer by SEM micrographs. The evaluated dielectric properties (ε' = 424; tan δ = 2.14 at 130 °C and 100 Hz frequency for 20 wt% loading of K₂Ti₆O₁₃) for polymer composite are higher in compared to pure polymer. The enhancement in dielectric constant and changing the surface properties of polymer composite can be used for the development of electrochemical storage device applications.     

Preparation of Y<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> pyrochlore using high-energy ball milling and their structural,thermal and conducting properties

Pyrochlore-structured materials are very important materials due to their structural and conducting properties. These properties can be further modified by changing processing conditions. In the present study, pyrochlore (Y₂Ti₂O₇) is synthesized using high-energy ball milling. During various stages of ball milling, the ball-milled powder is taken for investigating the structural and thermal properties. The replacement of Ti₂O₃ by TiO₂ in nominal composition leads to lower ball milling duration to form Y₂Ti₂O₇. Differential thermal analysis showed the single exothermic peak below 800 °C, which indicates formation of disordered pyrochlore phase. The as prepared powders (40-h ball milled) were compacted and heat treated at 1,450 °C for 12 h. The conductivity of sintered sample is found to be one order higher than earlier reported pure Y₂Ti₂O₇ pyrochlore.     

NO<Subscript>2</Subscript>-sensing properties of La<Subscript>0.65</Subscript>Sr<Subscript>0.35</Subscript>MnO<Subscript>3</Subscript> synthesized by self-propagating combustion

Ultrafine-structure La_0.65Sr_0.35MnO₃ (LSM) powders synthesized by self-propagating combustion method have been used to fabricate sensing electrodes (SEs) for NO₂ mixed-potential sensors based on yttria-stabilized zirconia (YSZ). This type of sensor was found to provide better NO₂ sensitivity at 500 °C than sensors with LSM powders synthesized by traditional solid-state methods. The response values of the sensor have good linear relationship (sensitivity 36.6 mV/decade and linear fit 0.99) with the logarithm of NO₂ concentration varying from 30 to 500 ppm. The influence of sintering temperature (1000, 1100, 1200, and 1300 °C) on sensor response was also examined and was found to have a significant effect on the morphology of LSM-SEs. Moreover, in the presence of NO, CO₂, CO, and NO₂, the sensor exhibited good NO₂ selectivity.     

Structure,thermal behavior,and dielectric properties of new cesium hydrogen sulfate arsenate: Cs<Subscript>2</Subscript>(HSO<Subscript>4</Subscript>)(H<Subscript>2</Subscript>AsO<Subscript>4</Subscript>)

Synthesis and structural characterization by single-crystal X-ray diffraction method, thermal behavior, and electrical proprieties are given for a new compound with a superprotonic phase transition Cs₂(HSO₄)(H₂AsO₄). The title compound crystallizes in the monoclinic system with the P2₁/n space group. The structure contains zigzag chains of hydrogen-bonded anion tetrahedra that extend in the [010] direction. Each tetrahedron is additionally linked to a tetrahedron neighboring chain to give a planar structure with hydrogen-bonded sheets lying parallel to (10ī). The existence of O–H and (S/As)–O bonds in the structure at room temperature has been confirmed by IR and Raman spectroscopy in the frequency ranges 4000–400 cm^?1and 1200–50 cm^?1, respectively. Differential scanning calorimetry analysis of the superprotonic transition in Cs₂(HSO₄)(H₂AsO₄) showed that the transformation to high temperature phase occurs at 417 K by one-step process. Thermal decomposition of the product takes place at much higher temperatures, with an onset of approximately 534 K. The superprotonic transition was also studied by impedance and modulus spectroscopy techniques. The conductivity in the high temperature phase at 423 K is 1.58 × 10^?4 Ω^?1 cm^?1, and the activation energy for the proton transport is 0.28 eV. The conductivity relaxation parameters associated with the high disorder protonic conduction have been examined from analysis of the M”/M”_max spectrum measured in a wide temperature range. Transport properties of this material appear to be due to the proton hopping mechanism.     

Thermal conductivity of Na<Subscript>2</Subscript>W<Subscript>2</Subscript>O<Subscript>7</Subscript> crystal

The thermal conductivity of Na₂W₂O₇ single crystal has been studied along the main crystallographic directions at temperatures of 50–573 K. A low thermal conductivity is found to correlate with a significant difference in the cation weight.     

Semiconducting SnO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> (S-T) composites for detection of SO<Subscript>2</Subscript> gas

SnO₂-TiO₂ (S-T) composites with different molar ratios were prepared by mechanical mixing followed by sintering at 700 °C for 4 h in air. The structural and microstructural properties of the composites were investigated using powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM). S-T composites were investigated by introducing SO₂ to test their chemical stability using PXRD and SEM coupled with energy dispersive X-ray (EDX) analysis. The sensing performance was measured at different temperatures using various SO₂ concentrations (10–100 ppm). A composite comprising 25 mol% of SnO₂ and 75 mol% TiO₂ (S25-T75) exhibited the highest sensitivity comparing to other S-T composites studied under the presently investigated conditions. t ₉₀ (90 % of response time) was found to be ～5 min for thick pellet (~2 mm in thickness). SO₂ sensing mechanism has been explained through the band structure model.     

Synthesis and electrochemical properties of Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion battery

The layered Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ lithium-rich manganese-based solid solution cathode material has been synthesized by a simple solid-state method. The as-prepared material has a typical layered structure with R-3m and C2/m space group. The synthesized Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has an irregular shape with the size range from 200 to 500 nm, and the primary particle of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has regular sphere morphology with a diameter of 320 nm. Electrochemical performances also have been investigated. The results show that the cathode material Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ prepared at 900 °C for 12 h has a good electrochemical performance, which can deliver a high initial discharge capacity of 233.5, 214.2, 199.3, and 168.1 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. After 50 cycles, the capacity retains 178.0, 166.3, 162.1, and 155.9 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. The results indicate that the simple method has a great potential in synthesizing manganese-based cathode materials for Li-ion batteries.     

Thermal sensors based on Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> and (Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>70</Subscript>(Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>30</Subscript> thin films

Thin films of Sb₂Te₃ and (Sb₂Te₃)₇₀(Bi₂Te₃)₃₀ alloy and have been deposited on precleaned glass substrate by thermal evaporation technique in a vacuum of 2?×?10^?6 Torr. The structural study was carried out by X-ray diffractometer, which shows that the films are polycrystalline in nature. The grain size, microstrain and dislocation density were determined. The Seebeck coefficient was determined as the ratio of the potential difference across the films to the temperature difference. The power factor for the (Sb₂Te₃)₇₀ (Bi₂Te₃)₃₀ and (Sb₂Te₃) is found to be 19.602 and 1.066 of the film of thickness 1,500 Å, respectively. The Van der-Pauw technique was used to measure the Hall coefficient at room temperature. The carrier concentration was calculated and the results were discussed.     

Ionic displacements and structure of disordered PbFe<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript>

A sequence of structural models of unit cells of complex oxides with perovskite-type structure has been constructed to refine the average structure of PbFe_1/2Nb_1/2O₃ (PFN) at temperatures above the ferroelectric Curie point (T _C ～ 110°C). Owing to the analysis of the probability theory considerations, each model is characterized by only two positional fitting parameters. With the use of the intensities of 95 symmetrically independent X-ray reflections from a PFN single crystal at 160°C, a model with the R factor below 3% (K = 2.44%) was chosen. The ravine method has been used to verify the existence of a single minimum for the R factor with respect to the fitting parameter.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.