Synthesis and nonlinear optical properties of methacrylate polymers based on 2‐[4‐(N‐methyl,N‐hydroxyethylamino)phenylazo]‐phenyl‐6‐nitrobenzoxazole chromophore

Methacrylate polymers containing different molar contents of nonlinear optical (NLO) active molecular segments based on 2‐[4‐(N‐methyl,N‐hydroxyethylamino)phenylazo]‐phenyl‐6‐nitrobenzoxazole chromophores were synthesized, and their phase behavior and second‐order NLO properties were investigated. Polymers containing 6–17 mol % chromophore segments allowed the preparation of amorphous and optically clear thin films. Some mesomorphic structuration was exhibited by a polymer with 33 mol % chromophoric units. However, this feature did not prevent the possibility of investigating the NLO properties. Nonlinear resonance‐enhanced d₃₃ coefficients were determined by second harmonic generation experiments on spin‐coated, corona‐poled thin films at λ = 1064 nm. Values ranging from 40 to 60 pm/V were measured with increasing chromophore molar contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1841–1847, 2003     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Chiral crystal of a C2v‐symmetric 1,3‐diazaaulene derivative showing efficient optical second harmonic generation

Achiral nonlinear optical (NLO) chromophores 1,3‐diazaazulene derivatives, 2‐(4′‐aminophenyl)‐6‐nitro‐1,3‐diazaazulene (APNA) and 2‐(4′‐N,N‐diphenylaminophenyl)‐6‐nitro‐1,3‐diazaazulene (DPAPNA), were synthesized with high yield. Despite the moderate static first hyperpolarizabilities (β₀) for both APNA [(136 ± 5) × 10^?30 esu] and DPAPNA [(263 ± 20) × 10^?30 esu], only APNA crystal shows a powder efficiency of second harmonic generation (SHG) of 23 times that of urea. It is shown that the APNA crystallization driven cooperatively by the strong H‐bonding network and the dipolar electrostatic interactions falls into the noncentrosymmetric P2₁2₁2₁ space group, and that the helical supramolecular assembly is solely responsible for the efficient SHG response. To the contrary, the DPAPNA crystal with centrosymmetric P‐1 space group is packed with antiparalleling dimmers, and is therefore completely SHG‐inactive. 1,3‐Diazaazulene derivatives are suggested to be potent building blocks for SHG‐active chiral crystals, which are advantageous in high thermal stability, excellent near‐infrared transparency and high degree of designing flexibility. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Synthesis and properties of novel Y‐type nonlinear optical polyimides with high thermal stability of second harmonic generation

2,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐1‐(2,2‐dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide and 4,4′‐(hexafluoroisopropylidene)dianiline to yield novel Y‐type polyimides 5‐7 containing 2,4‐dioxybenzylidenemalononitrile groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone. The resulting polyimides 5‐7 are soluble in polar solvents such as dimethylsulfoxide and N,N‐dimethylformamide. Polymers 5‐7 showed a thermal stability up to 330 °C in thermogravimetric analysis thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 179–194 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 5.56 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 20 °C higher than the glass‐transition temperature there was no SHG decay below 215 °C because of the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3078–3087, 2008     

New PVK‐based nonlinear optical polymers: Enhanced nonlinearity and improved transparency

A series of poly(vinylcarbazole)‐based polymers containing sulfonyl‐based nonlinear optical chromophores as the side chains were prepared conveniently through a postfunctionalization approach. In the polymers, the subtle structure of the chromophore moieties could be easily modified by the introduction of different isolation group, to adjust the property of the resultant polymers. The polymers exhibited good optical transparency, besides their good processability and thermal stability. The poled polymer films exhibited large second harmonic generation (SHG) coefficients of d₃₃ values (up to 28.6 pm/V) with excellent thermal stability (about 90% of the maximal SHG coefficients remain at ～ 110 °C). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2983–2993, 2008     

Synthesis and characterization of organosoluble polyimides with trifluoromethyl‐substituted benzene in the side chain

New aromatic diamines substituted with a trifluoromethyl group in the side chain, 2,4‐diamino‐3′‐trifluoromethylazobenzene, 2,4‐diamino‐1‐[(4′‐trifluoromethylphenoxy) phenyl] aniline, and 3,5‐diamino‐1‐[(4′‐trifluoromethyl phenoxy) phenyl] benzamide were synthesized and characterized and used to prepare polyimides by a one‐step high‐temperature polycondensation method. Experimental results indicated that the prepared polyimides possess good solubility in strong organic solvents such as N‐methyl‐2‐pyrrolidinone, N,N′‐dimethylformamide, and N,N′‐dimethylacetamide. Homogeneous solutions with solid contents as high as 15–20% can be prepared, which are stable for storing longer than 2 weeks at room temperature. The polyimides exhibited glass‐transition temperatures of 249–292 °C and good thermal stability. The PI‐I_c and PI‐III_c films prepared by casting the fully imidized polymer solutions showed good transparency with cutoff wavelengths at 320–330 nm. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1572–1582, 2002     

Polyterephthalamides with naphthoxy‐pendent groups

A series of new aromatic polyamides having pendent naphthoxy groups were synthesized by the triphenyl phosphite‐activated polycondensation of (2‐naphthoxy)terephthalic acid (NOTPA) with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The diacid monomer NOTPA was prepared from the nitro displacement of dimethyl 2‐nitroterephthalate with the potassium naphthoxide of β‐naphthol, followed by base‐induced ester hydrolysis. All the resulting polymers were noncrystalline and readily soluble in aprotic polar solvents such as NMP and N,N‐dimethylacetamide. Almost all the polymers could be solution‐cast to tough, creasable amorphous films with good mechanical properties, the values of tensile strengths ranging from 90 to 124 MPa with initial moduli ranging from 1.72 to 2.51 GPa. Except for two examples, all the other polyamides displayed discernible glass transitions between 189 and 248 °C in the differential scanning calorimetric traces. These polyamides showed insignificant decomposition below 400 °C in nitrogen or air. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1781–1789, 2002     

Synthesis of poly(p‐phenylene vinylene)‐ and poly(phenylene ethynylene)‐based polymers containing p‐terphenyl in the main chain with alkoxyphenyl side groups

Starting from the pyrylium salt and following a facile synthetic route, we synthesized and polymerized 4,4″‐diiodo‐2′,6′‐di[4‐(2′‐ethylhexyl)oxy]phenyl‐p‐terphenyl with p‐divinylbenzene or p‐diethynylbenzene. The resulting polymers had moderate molecular weights, were amorphous, and dissolved in tetrahydrofuran and chloroform, with glass‐transition temperatures of 120–131 °C. The polymers behaved as violet‐blue‐emitting materials with photoluminescence maxima around 420 and 450 nm in solution and in thin films, respectively. They possessed well‐defined chromophores resulting from steric interactions in the polymer chain. The photoluminescence quantum yields were up to 0.29. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2591–2600, 2002     

Carbazole main-chain polymers for multifunctional materials: Synthesis and characterization

A series of α,ω-bis(3-formylcarbazolyl)alkane monomers have been prepared starting from carbazole and α,ω-dibromoalkane in two steps. Main-chain polymers with carbazole substituted with one acceptor group as the nonlinear optical (NLO) chromophores and photoconductive moieties were synthesized by the Knoevenagel polycondensation of α,ω-bis(3-formylcarbazolyl)alkane and 1,6-bis(cyanoacetoxy)hexane using 4-(N,N-dimethyl)pyridine (DMAP) as a base. This Knoevenagel polycondensation involved two stages: polycondensation was first carried out in tetrahydrofuran solution, and then polycondensation was allowed to continue in the solid-state after removal of solvent. All of these main-chain polymers characterized by spectroscopic methods and elemental analyses are soluble in common low boiling organic solvents, such as chloroform. These polymers were found to be amorphous with glass transition temperatures in the range of 94–117°C by differential scanning calorimetry. This two-stage polycondensation gave polymers with weight-average molecular weight in the range of 25,000–72,000 g/mol by gel permeation chromatography. The study of the nonlinear optical and photorefractive properties of these polymers is in progress. © 1996 John Wiley & Sons, Inc.     

Second‐harmonic response of a series of chiral polyesters: A joint experimental and theoretical study

A series of polyesters with π‐conjugated donor–acceptor segments was synthesized by the condensation of azobenzene‐4,4′‐dicarbonylchloride with 1,4:3,6‐dianhydro‐D‐sorbitol ([α] = + 42.5°) and biphenolic chromophores, bis(4‐hydroxyphenylazo)‐2,2′‐dinitrodiphenylmethane and bis(4‐hydroxyphenylazo)‐2,2′‐dinitrodiphenylsulfone. The polymers were characterized by spectral methods (IR, ultraviolet–visible, and NMR), thermal methods (thermogravimetry and differential scanning calorimetry), wide‐angle X‐ray scattering, and polarimetry. The polymers containing isosorbide units were optically active and crystalline. They exhibited glass‐transition temperature values between 100 and 160 °C and were stable up to 400 °C. The second‐harmonic generation (SHG) efficiency of the polymers was experimentally verified by a powder‐reflection technique with 2‐methyl‐4‐nitroaniline as a reference. The SHG efficiencies of the polymers were compared to those of the chromophores and explained as a function of the percentage of chiral composition. The hyperpolarizability β values were also determined by a two‐level model solvatochromic method and computational methods. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2868–2877, 2002     

Synthesis and electro‐optic properties of novel X‐type polyurethane containing nitrophenylazonitroresorcinoxy group with highly enhanced thermal stability of dipole alignment

Novel X‐type polyurethane 4 containing 4‐(4‐nitrophenylazo)‐6‐nitroresorcinoxy groups as nonlinear optical (NLO) chromophores, which are parts of the polymer main chains, was prepared and characterized. Polyurethane 4 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It shows thermal stabilities up to 270 °C from thermogravimetric analysis with glass transition temperature obtained from differential scanning calorimetry of about 134 °C. The second harmonic generation (SHG) coefficient (d₃₃) of poled polymer film at 1064 nm fundamental wavelength is 5.37 × 10^?9 esu. Polymer 4 exhibits a thermal stability up to T_g, and no significant SHG decay is observed below 135 °C, which is acceptable for NLO device applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 760–766     

The design,synthesis, and nonlinear optical properties of novel X‐type polyurethane containing dicyanovinylnitroresorcinoxy group with enhanced SHG thermal stability

Novel X‐type polyurethane 5 containing 4‐(2′,2′‐dicyanovinyl)‐6‐nitroresorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone, was prepared and characterized. Polyurethane 5 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It shows thermal stability up to 280 °C from thermogravimetric analysis with a glass transition temperature (T_g) obtained from differential scanning calorimetry thermogram of around 120 °C. The second harmonic generation (SHG) coefficient (d₃₃) of poled polymer film at 1064‐nm fundamental wavelength is around 6.12 × 10^?9 esu. The dipole alignment exhibits a thermal stability even at 5 °C higher than T_g, and there was no SHG decay below 125 °C due to the partial main chain character of the polymer structure, which is acceptable for NLO device applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and properties of new soluble aromatic polyamides and polyimides on the basis of N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new N‐phenylated amide (N‐phenylamide) unit containing aromatic diamine, N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 3‐nitrobenzoyl chloride, followed by catalytic reduction. Two series of organosoluble aromatic poly(N‐phenylamide‐imide)s and poly(N‐phenylamide‐amide)s with inherent viscosities of 0.58–0.82 and 0.56–1.21 dL/g were prepared by a conventional two‐stage method and the direct phosphorylation polycondensation, respectively, from the diamine with various aromatic dianhydrides and aromatic dicarboxylic acids. All polyimides and polyamides are amorphous and readily soluble in many organic solvents such as N,N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with high tensile strengths. These polyimides and polyamides had glass‐transition temperatures in the ranges of 230–258 and 196–229 °C, respectively. Decomposition temperatures of the polyimides for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2564–2574, 2002     

Study on side-chain second-order nonlinear optical polyimides based on novel chromophore-containing diamines. I. Synthesis and characterization

Side-chain second-order nonlinear optical polyimides were prepared from four novel chromophore-containing diamines and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride by a traditional two-step process that included a solution polycondensation followed by a chemical imidization. The four diamines were 2,4-di-β-aminoethylamino-6-p-nitrophenylamino-1,3,5-triazine (M1), 4-nitro-4′-[N-(4,6-di-β-aminoethylamino)-1,3,5-triazin-2-yl]amino azobenzene (M2), 2,4-di-p-aminophenylamino-6-p-nitrophenylamino-1,3,5-triazine (M3), and 4-nitro-4′-[N-(4,6- di-4-aminophenylamino)-1,3,5-triazin-2-yl]amino azobenzene (M4). All the polyimides exhibited maximum ultraviolet-visible absorption peaks or shoulders of chromophores at wavelengths below 400 nm, and those based on M1 and M3 were transparent at wavelengths above 450 nm, whereas those based on M2 and M4 were transparent at wavelengths above 550 nm. The polyimides possessed high glass-transition temperatures (T_g's; 218–247 °C) and thermal decomposition temperatures. They were soluble in aprotic solvents such as N-methyl-2-pyrrolidone, N,N-dimethyl acetamide, N,N-dimethyl formamide, and dimethylsulfone. Some were even soluble in common low-boiling-point solvents such as tetrahydrofuran. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4330–4336, 1999     

Synthesis and characterization of new organosoluble polyamides derived from bis[4‐(4‐carboxyphenoxy) phenyl]diphenylmethane

A new dicarboxylic acid containing a diphenylmethylene linkage, bis[4‐(4‐carboxyphenoxy)phenyl]diphenylmethane (BCAPD), was prepared from bis(4‐hydroxphenyl)diphenylmethane and p‐fluorobenzonitrile via an aromatic nucleophilic substitution reaction followed by hydrolysis. A series of novel polyamides were prepared by the direct polycondensation of BCAPD and various aromatic diamines. The polymers were produced with moderate to high inherent viscosities of 0.80–0.85 dL g^?1. Nearly all the polymers were readily soluble in polar solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide, in less polar solvents such as pyridine and cyclohexanone, and in tetrahydrofuran. All the polymers were amorphous, and the polyamide films had a tensile strength and a tensile modulus greater than 80 MPa and 2.0 GPa, respectively. These polyamides had glass‐transition temperatures between 249 and 274 °C, and their temperatures at a 10% weight loss were 477–538 and 483–540 °C in nitrogen and air atmospheres, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1156–1161, 2001     

Molecular design,synthesis, and nonlinear optical properties of novel T‐type polyimides with exceptionally high thermal stability of the second harmonic generation

2,5‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐4′‐nitrostilbene dianhydride was prepared and reacted with 1,4‐phenylenediamine, 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide, and 4,4′‐(hexafluoroisopropylidene)dianiline to yield unprecedented novel T‐type polyimides ( 4 – 7 ) containing 2,5‐dioxynitrostilbenyl groups as nonlinear optical chromophores, which constituted parts of the polymer backbones. 4 – 7 were soluble in polar solvents such as acetone and N,N‐dimethylformamide. They showed thermal stability up to 300 °C in thermogravimetric analysis thermograms; the glass‐transition temperatures obtained from differential scanning calorimetry thermograms were around 153 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064‐cm^?1 fundamental wavelength were around 4.35 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 45 °C higher than the glass‐transition temperature, and there was no SHG decay below 200 °C because of the partial main‐chain character of the polymer structure, which was acceptable for nonlinear optical device applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3189–3199, 2004     

Synthesis and nonlinear optical properties of novel Y‐type polyester containing tricyanovinylthiazolylazoresorcinoxy group with enhanced thermal stability of dipole alignment

Novel Y‐type polyester 4 containing 5‐methyl‐4‐{5‐(1,2,2‐tricyanovinyl)‐2‐thiazolylazo}resorcinoxy groups as nonlinear optical (NLO) chromophores, which are parts of the polymer backbone, was prepared, and its NLO properties were investigated. Polyester 4 is soluble in common organic solvents such as N,N‐dimethylformamide and dimethylsulfoxide. Polymer 4 shows a thermal stability up to 250 °C from thermogravimetric analysis with glass‐transition temperature obtained from differential scanning calorimetry of approximately 94 °C. The second harmonic generation (SHG) coefficient (d₃₃) of poled polymer film at 1560‐nm fundamental wavelength is 8.12 × 10^?9 esu. The dipole alignment exhibits a thermal stability even at 6 °C higher than glass‐transition temperature (T_g), and no significant SHG decay is observed below 100 °C due to the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and properties of alternating copolyamide‐imides based on 2,6‐bis(4‐aminophenoxy)naphthalene and comparison with its related isomeric polymers

A series of novel polyamide‐imides III containing 2,6‐bis(phenoxy)naphthalene units were synthesized by 2,6‐bis(4‐aminophenoxy)naphthalene and various bis(trimellitimide)s in N‐methyl‐2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents through direct polycondensation. The polymers were obtained in quantitative yield with inherent viscosities up to 1.53 dL/g. Most of the polymers showed good solubility in NMP, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide and could be solution‐cast into transparent, flexible, and tough films. The films had tensile strengths of 84–111 MPa, elongations at break of 8–33%, and initial moduli of 2.2–2.8 GPa. Wide‐angle X‐ray diffraction revealed that most polymers III were amorphous. The glass‐transition temperatures of some of the polymers could be determined by differential scanning calorimetry traces, recorded at 247–290 °C. The polyamide‐imides exhibited excellent thermal stabilities and had 10% weight loss at temperatures in the range of 501–575 °C under nitrogen atmosphere. They left more than 57% residue even at 800 °C in nitrogen. A comparative study of some corresponding polyamide‐imides is also presented. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2591–2601, 2001     

Synthesis and chiroptical properties of optically active polymer liquid crystals containing azobenzene chromophores

A series of optically active methacrylic homopolymers, poly[(4‐{4′‐[(S)‐2‐methyl‐1‐butyloxycarbonyl]phenylazo}phenoxyl)x‐methylene methacrylate] (x = 0, 2, 6, or 11), were synthesized. The structures of the polymers were characterized by IR, ¹H NMR, UV, differential scanning calorimetry, and gel permeation chromatography. The chiroptical properties of the polymers in films were investigated with circular dichroism (CD) measurements. The CD and UV spectra of the films suggested that CD absorptions occurred in the films of the polymers with long spacers (x = 6 or 11) but not in the films of the polymers with short spacers (x = 0 or 2). After irradiation with linearly polarized light at 442 nm, the CD values were amplified in all the polymeric films. The amplificatory values of the CD bands in the absorption region (260–360 nm) of azobenzene chromophores suggested that the spacer length had an effect on both the transfer of chirality and photoinduced chirality in the polymeric films. The largest level of photoinduced chirality was induced in the polymer containing six methylene units. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3210–3219, 2006     

Synthesis,optical, and electrochemical properties of novel copolymers on the basis of benzothiadiazole and electron‐rich arene units

Novel alternating conjugated copolymers ( P1–P6 ) consisting of an electron‐deficient benzothiadiazole and a variety of electron‐rich thiophene‐arene‐thiophene units were synthesized by palladium‐catalyzed polycondensations (Stille and Suzuki reactions), aiming at processable materials with a reduced optical band gap. The structures of P1–P6 were confirmed by ¹H NMR and ¹³C NMR, and their molecular weights were determined by size exclusion chromatography. In the Suzuki polycondensation, the role of the catalyst [Pd(PPh₃)₄ and Pd(OAc)₂] on the resulting molecular weight was investigated. Pd(OAc)₂ enhances the molecular weight of the polymers for both thiophene and phenylene bis‐boronic esters as compared with Pd(PPh₃)₄. The optical properties of the polymers were examined in solution and the solid state. The polymers with n‐octyl substituents ( P1 , P4 , P5 , and P6 ) on the thiophene rings possessed less‐planar structures as a result of torsional steric hindrance, and their absorption spectra appeared blueshifted as compared with their unsubstituted analogues ( P2 and P3 ). The electrochemical properties of the polymers were studied using cyclic voltammetry. Although the alkyl substitution affects the oxidation potential, only marginal differences in the reduction potentials were observed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2360–2372, 2002