Fluoropolyethers end‐capped by polar functional groups. II. Effect of catalyst and reagents concentration,solvent nature,and temperature on reaction kinetics of α,ω‐bis(hydroxy)‐terminated fluoropolyethers with cycloalyphatic and aromatic diisocyanates

A comparative kinetic study of the dibutyltin dilaurate (DBTDL) and 1,4‐diazabicyclo[2,2,2]octane (DABCO) catalyzed reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers (FPEs)—Z‐DOLs and Z‐DOL TXs—of various molecular weights and purity, with 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI), isophorone diisocyanate (IPDI) and 2,4‐toluene diisocyanate (TDI) was carried out in different solvents. An analytical method was used to follow the kinetics of the reactions at four different temperatures. The rate of NCO disappearance measured by two independent methods—IR spectroscopy and chemical titration were found to be very close. Straight proportionality between rate constants k_cat and catalyst concentration was found. But in some cases for the DBTDL catalyzed reactions effect of catalyst saturation along with appearance of the limiting DBTDL concentration C_lim below which the rate of reaction was close to zero were observed. Reactivity of Z‐DOLs in the tin‐catalyzed urethane reactions was found to decrease with their storage time at RT due to the slow hydrolysis of the end  COOR groups impurities, which give the corresponding acids that act as a strong inhibitor of the DBTDL activity. These acid admixtures have no influence on the DABCO catalyzed reactions. For the DBTDL and DABCO catalyzed reactions of Z‐DOLs with IPDI the dependence of effective rate constants k_eff (where k_eff = k_cat · 0.01/[DBTDL] and catalyst concentration is taken in mol % based on IPDI) on total reagents concentration were found to be described by curves with a maximum. Critical reagents concentration, after which the relationship k_eff = f (C) changes from proportional to inverse proportional, seems do not substantially depend on the solvent nature. Hydrogenated analog poly(ethylene glycol) MW 400 (PEG‐400) differs greatly from Z‐DOLs: only steady decrease of k_eff was observed with increase of reagents concentration C from 5 up to 95 wt %. Activation energies for all the studied reactions are within the range of 10.8–16.7 kcal/mol. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2579–2602, 2000     

Fluoropolyethers end‐capped by polar functional groups. IV. A novel approach to the evaluation of reactivities of hydroxy‐terminated ethoxylated fluoropolyethers in the tin(IV)‐catalyzed reactions with isophorone diisocyanate

The effect of catalyst dibutyltin dilaurate (DBTDL) on the kinetics of urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Fomblin® Z‐DOL TXs (FPEs) of various molecular weights and poly(oxyethylene) glycol PEG‐400 with isophorone diisocyanate (IPDI) in hexafluoroxylene (HFX) and tetrahydrofuran (THF) at 40 °C and NCO:OH = 2:1 have been studied in a broad range of catalyst (0.10–9.00) ×10^?4 M and total reagents (10.0–60.1 wt %) concentrations. The rate of tin‐catalyzed second‐order reactions (with respect to diol and diisocyanate) was found to be proportional to the square root of catalyst concentration [DBTDL]^0.5 both in low polar (HFX) and polar (THF) solvents. Effect of catalyst saturation was revealed for all the reaction systems at higher DBTDL concentrations as well as the appearance of the limiting catalyst concentrations C_lim below which the rates of reaction were close to zero. Based on these findings new effective rate coefficients have been derived k = k_cat/(C ? C) that are independent of the total reagent concentration in the range of 10.0–60.1 wt % ([OH] = 0.10–0.91 equiv/L). This new approach highlights that the rate of the tin‐catalyzed urethane formation reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers Z‐DOL TXs with IPDI in HFX at 40 °C and NCO:OH = 2:1 increases significantly with increasing MW of FPE from 776 up to 3405. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5354–5371, 2004     

Chain‐extended,hydroxyterminated‐polybutadiene‐based polyurethaneureas: Synthesis,reaction kinetics,and properties

Hydroxyterminated‐polybutadiene‐based prepolyurethanes were prepared with two different catalysts, dibutyltindilaurate (DBTDL) and triethylamine (TEA); chain extension of the prepolyurethanes followed with two different aromatic diamines, oxydianiline and 4,4′‐diaminodiphenylsulfone, in various concentrations. The prepolyurethane synthesis followed second‐order kinetics, with the DBTDL catalyst showing better efficiency for urethane formation than TEA. TEA‐catalyzed synthesis suffered from the self‐association of isocyanates as a major side reaction, following second‐order kinetics with respect to isocyanate concentration. Although there was a gradual increase in the intrinsic viscosity during prepolyurethane synthesis in the presence of DBTDL, the intrinsic viscosity remained almost constant with the progress of the reaction in the presence of TEA. The tensile properties of prepolyurethane and polyurethaneureas synthesized in DBTDL‐catalyzed reactions were higher than the properties of those synthesized in TEA‐catalyzed reactions. The variation of the tensile strength with the diamine concentration was correlated with the crosslink density and sol fraction. The solubility of the hard segment of polyurethaneurea in the reaction medium appeared to be important in influencing the tensile properties. The effects of the diamine concentration (chain extender) on the diffusion coefficient and activation energy of diffusion of toluene in polyurethaneureas were studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2978–2992, 2001     

Fluoropolyethers end‐capped by polar functional groups. I. Kinetic approach to the reaction of hydroxy‐terminated fluoropolyethers with cycloalyphatic and aromatic diisocyanates

Urethane reactions of cycloaliphatic and aromatic diisocyanates with hydroxy‐terminated fluoropolyethers (FPEs) of various molecular weights and structure, at NCO : OH = 2, have been studied by monitoring, by IR analysis, the rate of decrease in NCO absorbance at 2264–2268 cm⁻¹. Different diisocyanates have been tested, among them the following: 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI); 5‐isocyanato‐1,3,3‐trimethylcyclohexylmethyl isocyanate or isophorone diisocyanate (IPDI); 2,4‐toluene diisocyanate (TDI). Ethyl acetate (EA), methyl isobutyl ketone (MIBK), and hexafluoroxylene (HFX) have been used as solvents in presence of dibutyltin dilaurate (DBTDL) or 1,4‐diazabicyclo[2.2.2]octane (DABCO) as catalysts. These reactions gave rise to NCO‐end‐capped FPE–oligourethanes. Preliminary solubility tests for HO‐terminated FPEs in various solvents made it possible to select proper candidates for carrying out reaction in homogeneous conditions at high concentrations of reagents (30–50% w/w). The second‐order kinetic mechanism was shown to be valid. Positive deviations from linearity for the second‐order kinetics around 40–80% conversion, found for most of the FPE diols, were attributed to the autocatalysis of the isocyanate–hydroxyl reaction by the arising urethane groups. Uncatalyzed reactions with cycloaliphatic diisocyanates are very slow at 40°C. The tertiary amine DABCO is a much less effective catalyst than DBTDL. FPEs having terminal OH groups separated from the perfluorinated main molecular chain by  (OCH₂CH₂)_n segments (n = 1–2) are generally more reactive than FPEs with end  CH₂OH groups. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 557–570, 1999     

Synthesis of new fluorinated allyl ethers for the surface modification of thiol–ene ultraviolet‐curable formulations

Thiol–ene photocurable systems based on a trifunctional thiol [trimethylolpropane tris‐(3‐mercaptopropanoate)] and two different multifunctional allyl ethers (trimethylolpropane triallyl ether and Boltorn U2, an allyl functional dendritic polyester) were examined. To these systems, small amounts (<1 wt %) of fluorinated allyl ethers were added for the modification of their surface properties. Two new fluorinated allyl ethers, 1H,1H‐perfluoro‐1‐heptylallyl ether and 1H,1H‐perfluoro‐1‐decylallyl ether, were synthesized for this purpose by allylation of the corresponding 1H,1H‐perfluoro alcohols. The fluorinated monomers, despite their very low concentrations, caused sharp changes in the surface properties of the films and in the solvent resistance without any changes in the curing conditions and bulk properties. Completely hydrophobic surfaces were obtained (as a result of the selective enrichment of the fluorinated monomers on the film surfaces) that depended on the monomer structure and its concentration. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2583–2590, 2002     

Synthesis of poly(urethane‐imide) using aromatic secondary amine‐blocked polyurethane prepolymer

A set of poly(urethane‐imide)s were prepared using blocked Polyurethane (PU) prepolymer and pyromellitic dianhydride (PMDA). The PU prepolymer was prepared by the reaction of polyether glycol and 2,4‐tolylene diisocyanate, and end capped with N‐methyl aniline. The PU prepolymer was reacted with PMDA until the evolution of carbon dioxide ceased. The effect of tertiary amine catalysts, organo tin catalysts, solvents, and reaction temperature were studied and compared with the poly(urethane‐imide) prepared using phenol‐blocked PU prepolymer. N‐methyl aniline blocked PU prepolymer gave a higher molecular weight poly(urethane‐imide) at a lower reaction temperature in a shorter time. Amine catalysts were found to be more efficient than organo tin catalysts. The reaction was favorable in particular with N‐ethylmorpholine and diazabicyclo(2.2.2)octane (DABCO) as catalysts, and dimethylpropylene urea as a reaction medium. The poly(urethane‐imide)s were characterized by FTIR, GPC, TGA, and DSC analyses. The molecular weight decreased with an increase in reaction temperature. The thermal stability of the PU was found to increase by the introduction of imide component. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4032–4037, 2000     

Atom transfer radical polymerization of n‐butyl acrylate catalyzed by CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine

The homogeneous atom transfer radical polymerization (ATRP) of n‐butyl acrylate with CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine as a catalyst and ethyl 2‐bromoisobutyrate as an initiator was investigated. The kinetic plots of ln([M]₀/[M]) versus the reaction time for the ATRP systems in different solvents such as toluene, anisole, N,N‐dimethylformamide, and 1‐butanol were linear throughout the reactions, and the experimental molecular weights increased linearly with increasing monomer conversion and were very close to the theoretical values. These, together with the relatively narrow molecular weight distributions (polydispersity index ～ 1.40 in most cases with monomer conversion > 50%), indicated that the polymerization was living and controlled. Toluene appeared to be the best solvent for the studied ATRP system in terms of the polymerization rate and molecular weight distribution among the solvents used. The polymerization showed zero order with respect to both the initiator and the catalyst, probably because of the presence of a self‐regulation process at the beginning of the reaction. The reaction temperature had a positive effect on the polymerization rate, and the optimum reaction temperature was found to be 100 °C. An apparent enthalpy of activation of 81.2 kJ/mol was determined for the ATRP of n‐butyl acrylate, corresponding to an enthalpy of equilibrium of 63.6 kJ/mol. An apparent enthalpy of activation of 52.8 kJ/mol was also obtained for the ATRP of methyl methacrylate under similar reaction conditions. Moreover, the CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine‐based system was proven to be applicable to living block copolymerization and living random copolymerization of n‐butyl acrylate with methyl methacrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3549–3561, 2002     

Application of ketenes to well‐defined polyester synthesis (4): End‐capping reactions in living anionic polymerization of ethylphenylketene

End‐capping reactions of a living polyester, obtained by anionic polymerization of ethylphenylketene (EPK), were carried out. As end‐capping reagents, electrophiles such as alkyl halide and acyl halide were successfully used. Reactivity of the terminal enolate and the resulting terminal structures were elucidated by model reactions, using lithium enolates having low molecular weights, obtained by an equimolar reaction of EPK with butyllithium. Polymerization of EPK by lithium alkoxide and the subsequent end‐capping reaction afforded the corresponding polyester having functional groups at both chain ends and a narrow molecular weight distribution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3103–3111, 2002     

Palladium‐Catalyzed Allylic Alkylation of Simple Ketones with Allylic Alcohols and Its Mechanistic Study

Allylic alcohols were directly used in Pd‐catalyzed allylic alkylations of simple ketones under mild reaction conditions. The reaction proceeded smoothly at 20 °C by the concerted action of a Pd catalyst, a pyrrolidine co‐catalyst, and a hydrogen‐bonding solvent, and does not require any additional reagents. A computational study suggested that methanol plays a crucial role in the formation of the π‐allylpalladium complex by lowering the activation barrier.     

Hydrogen effects in propylene polymerization reactions with titanium‐based Ziegler–Natta catalysts. II. Mechanism of the chain‐transfer reaction

Hydrogen is a very effective chain‐transfer agent in propylene polymerization reactions with Ti‐based Ziegler–Natta catalysts. However, measurements of the hydrogen concentration effect on the molecular weight of polypropylene prepared with a supported TiCl₄/dibutyl phthalate/MgCl₂ catalyst show a peculiar effect: hydrogen efficiency in the chain transfer significantly decreases with concentration, and at very high concentrations, hydrogen no longer affects the molecular weight of polypropylene. A detailed analysis of kinetic features of chain‐transfer reactions for different types of active centers in the catalyst suggests that chain transfer with hydrogen is not merely the hydrogenolysis reaction of the Ti? C bond in an active center but proceeds with the participation of a coordinated propylene molecule. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1899–1911, 2002     

Solvent‐free and nonisocyanate melt transurethane reaction for aliphatic polyurethanes and mechanistic aspects

A novel melt transurethane polycondensation route for polyurethanes under solvent‐free and nonisocyanate condition was developed for soluble and thermally stable aliphatic or aromatic polyurethanes. The new transurethane process was investigated for A + B, A‐A + B, and A‐A + B‐B (A‐urethane and B‐hydroxyl) ‐type condensation reactions, and also monomers bearing primary and secondary urethane or hydroxyl functionalities. The transurethane process was confirmed by ¹H and ¹³C NMR, and molecular weight of the polymers were obtained as M_n = 10–15 × 10³ and M_w = 15–45 × 10³ g/mol. The mechanistic aspects of the melt transurethane process and role of the catalyst were investigated using model reactions, ¹H NMR, and MALDI‐TOF‐MS. The model reactions indicated the occurrence of 97% reaction in the presence of catalyst, whereas its absence gave only less than 2% of the product. The polymer samples were subjected for end‐group analysis using MALDI‐TOF‐MS, which confirms the Ti‐catalyst mediated nonisocyanate pathway in the melt transurethane process. Almost all the polyurethanes were stable up to 280 °C, and the T_g of the polyurethanes can be easily fine‐tuned from ?30 to 120 °C by using appropriate diols in the melt transurethane process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2445–2458, 2008     

Versatile and controlled synthesis of resorbable star‐shaped polymers using a spirocyclic tin initiator—Reaction optimization and kinetics

A spirocyclic tin initiator was synthesized from pentaerythritol ethoxylate and dibutyltin oxide and used to polymerize L ‐lactide with dichloromethane, chloroform, toluene, and chlorobenzene as solvents. The reactions were performed at different temperatures and it is concluded that neither the temperature nor the solvent affects the molecular weight or the molecular weight distribution of the star‐shaped polymers. The reaction rate was significantly increased by raising the reaction temperature or choosing a solvent with a low dielectric constant. All polymers showed a molecular‐weight distribution below 1.19 and a molecular‐weight determined by the initial monomer to initiator concentration ([M]₀/[I]). No induction period was seen for the polymerizations. They were all first order in initiator and the degree of aggregation in toluene at 110 °C was found to be 4/5. The glass transition temperature and the melting temperature of the star‐shaped polymers increase with increasing arm length. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 596–605, 2006     

Synthesis and decrosslinking of networked polymers having zwitterion structure consisted by cyclic amidine and isothiocyanate

We have already found that the polymers, which are obtained by the polymerization of 4‐vinylphenyl isothoiocyanate after the zwitterion formation with cyclic amidines, are networked through the ionic interaction among the zwitterions becoming insoluble to various solvents. We report here on the results of the reaction of nucleophilic reagents such as amines and alcohols with the zwitterionic adduct to investigate about the decrosslinking through the resolution of ionic interactions. In the model reactions of amines and alcohols with the zwitterion compounds, which were consisted of the phenyl isothiocyanate and cyclic amidines, the reaction of nucleophilic reagents and zwitterionic adducts having methyl group at the 2‐position of the amidine proceed quantitatively. Based on the model reaction, such nucleophilic addition was applicable to decrosslinking reaction of the networked polymers containing the zwitterion structure in the side‐chain. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2131–2137     

Catalysis of N‐Methylaniline‐Blocked Polyisocyanate‐Hydroxyl‐Terminated Polybutadiene Cure Reaction

Catalysis of cure reaction between N‐methylaniline‐blocked polyisocyanate and hydroxyl‐terminated polybutadiene was investigated using a variety of tertiary amine and organotin catalysts. The catalytic activity of amine and organotin compounds was determined from the cure‐time results. It was found that the activity of the catalyst depends upon the steric constrain around the catalytic center. The organotin compounds showed higher catalytic activity than the amine catalysts. FTIR results obtained under isothermal condition revealed that DABCO selectively catalyze the urethane formation reaction, whereas DBTDL catalyze both the allophanate formation and urethane formation reactions during curing process. The synergistic effect of amine and organotin mixed catalysts on the cure reaction was also investigated.     

Copolymerization of 3‐buten‐1‐ol and propylene with an isospecific zirconocene/methylaluminoxane catalyst

The copolymerization of propylene and 3‐buten‐1‐ol protected with alkylaluminum [trimethylaluminum (TMA) or triisobutylaluminum] was conducted with an isospecific zirconocene catalyst [rac‐dimethylsilylbis(1‐indenyl)zirconium dichloride], combined with methylaluminoxane as a cocatalyst, in the presence of additional TMA or H₂ as the chain‐transfer reagent if necessary. The results indicated that end‐hydroxylated polypropylene was obtained in the presence of the chain‐transfer reagents because of the formation of dormant species after the insertion of the 3‐buten‐1‐ol‐based monomer followed by chain‐transfer reactions. The selectivity of the chain‐transfer reactions was influenced by the alkylaluminum protecting the comonomer and the catalyst structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5600–5607, 2004     

Heterogeneous catalysis by new bead‐shaped polymer‐supported multisite phase transfer catalysts

Three different new insoluble bead‐shaped polymer‐supported multisite phase transfer catalysts containing two, four and six active sites have been prepared and characterized by FTIR, TGA, [chloride ion] and SEM analyses. The presence of number of active sites in each catalyst and their corresponding catalytic ability were studied by determining pseudo‐first order rate constants for C‐alkylation of phenylacetonitrile (PAN) and four different substituted PAN as the substrate using a low concentration of NaOH (25% w/w) at 50 °C. The observed rate constants were compared with rate constants of same reactions catalyzed by single‐site catalyst under identical reaction conditions. From comparative study, the efficiency of catalysts were found to be in the order six‐site>four‐site>two‐site>single‐site thus confirming number of active sites in each catalyst. Further, the detailed kinetic profile of C‐alkylation of PAN has been investigated using the superior six‐site catalyst by varying stirring speed, [substrate], [catalyst], [NaOH], and temperature. Based on the observed kinetic and activation parameters, an interfacial mechanism was proposed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 771–785, 2009     

Thiol‐isocyanate‐acrylate ternary networks by selective thiol‐click chemistry

Thiol‐isocyanate‐acrylate ternary networks were formed by the combination of thiol‐isocyanate coupling, thiol‐acrylate Michael addition, and acrylate homopolymerization. This hybrid polymerization reaction sequence was preferentially controlled by using phosphine catalyst systems in combination with photolysis. The reaction kinetics of the phosphine/acrylate thiol‐isocyanate coupling reactions were systematically investigated by evaluating model, small molecule reactions. The thiol‐isocyanate reaction was completed within 1 min while the thiol‐acrylate Michael addition reaction required ～10 min. Both thiol‐isocyanate coupling and thiol‐acrylate Michael addition reactions involving two‐step anionic processes were found to be both quantitative and efficient. However, the thiol‐isocyanate coupling reaction was much more rapid than the thiol‐acrylate Michael addition, promoting initial selectivity of the thiol‐isocyanate reaction in a medium containing thiol, isocyanate, and acrylate functional groups. Films were prepared from thiol‐isocyanate‐acrylate ternary mixtures using 2‐acryloyloxyethylisocyanate and di‐, tri‐, and tetra‐functional thiols. The sequential thiol‐isocyanate, thiol‐acrylate, and acrylate homopolymerization reactions were monitored by infrared spectroscopy during film formation, whereas thermal and mechanical properties of the films were evaluated as a function of the chemical composition following polymerization. The results indicate that the network structures and material properties are tunable over a wide range of properties (T_g ～ 14–100 °C, FWHM ～ 8–46 °C), while maintaining nearly quantitative reactions, simply by controlling the component compositions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3255–3264, 2010     

Diels–Alder modification of poly(ethylene terephthalate‐co‐anthracene‐2,6‐carboxylate) with N‐substituted maleimides

Dimethyl 2,6‐anthracene dicarboxylate is used as a comonomer in the synthesis of functional copolymers that are subject to modification with Diels–Alder reactions. The formation of poly(ethylene terephthalate‐co‐2,6‐anthracenate), containing less than 20 mol % of the anthracene‐2,6‐dicarboxylate structural units, provides materials that are tractable and soluble. The anthracene units of the copolymers undergo Diels–Alder reactions with N‐substituted maleimides. The grafting of N‐alkylmaleimides affords soluble, hydrophobic polymers, whereas grafting with maleimide‐terminated poly(ethylene glycol) affords hydrophilic polymers. Because this reaction proceeds below the melting point of the copolymers, the procedure can be applied to thin films, whereby the surface properties are modified. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3256–3263, 2002     

Influence of residual impurities on ring‐opening metathesis polymerization after copper(I)‐catalyzed alkyne‐azide cycloaddition click reaction

Bottlebrush polymers (BBPs) are three‐dimensional polymers with great academic and industrial potential owing to their highly tunable and intricate architecture. The most popular method to synthesize BBPs is ring‐opening metathesis polymerization (ROMP) with Grubbs' catalyst, allowing living grafting‐through polymerization of macromonomers of up to ultrahigh molecular weights with narrow molecular weight distribution. In this case, it has been well recognized that the purity of macromonomers (MMs) is critical for a successful ROMP reaction. For MMs synthesized from reversible‐deactivation radical polymerization, Grubbs and Xia demonstrated that the better control of ROMP reaction can be achieved when they are prepared via “growth‐then‐coupling” method that is coupling a norbornenyl group to end‐functionalized prepolymers. However, these MMs can also contain various residual impurities from previous synthetic steps, which can potentially poison the catalyst and hamper the ROMP reaction. Herein, we intentionally doped possible impurities into purified MMs to identify the most poisoning species. As a result, it was found that alkyne‐functionalized norbornene most significantly retarded the ROMP reaction due to a formation of Ru‐vinyl‐carbene intermediates having low catalytic reactivity, whereas the other reagents such as solvent, Cu‐catalyst, ligands, and azido‐terminated prepolymers were relatively inert. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 726–737     

Degradation mechanism of poly(ether‐urethane) Estane® induced by high‐energy radiation. II. Oxidation effects

To predict long‐term polymer behavior during a nuclear waste storage time, radiation effects on a segmented aromatic poly(ether‐urethane) induced by high‐energy radiation under oxygen atmosphere were investigated. To obtain a predictive model of polymer radio‐oxidation during several centuries, the first step consists to elaborate the elementary degradation mechanisms. Thus, electron paramagnetic resonance (EPR), Fourier transform infra‐red spectroscopy (FT‐IR), electrospray ionisation‐mass spectrometry (ESI‐MS), and gas mass spectrometry were carried out to identify radicals, chemical modifications, and gases to reach the radio‐oxidative mechanism at doses inferior than 1000 kGy. Degradation mainly occurs at urethane bonds and in polyether soft segments that produces stable oxidative products as formates, alcohols, carboxylic acids and H₂, CO₂ and CO gases. Predominant degradation occurred at polyether soft segments and crosslinking is in competition with scission. On the basis of the results, a mechanism of degradation for aromatic poly(ether‐urethane) is proposed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 861–878, 2008