正负离子表面活性剂/离子液体双水相性质研究

本文把短链离子液体(IL)四氟硼酸1-乙基-3-甲基咪唑鎓[C2mim]BF4引入正负离子表面活性剂十二烷基硫酸钠(SDS)和十二烷基三甲基溴化铵(DTAB)双水相体系(SDS/DTAB/H2O)中,研究了IL对双水相相图及相分离体系性质的影响。结果表明,[C2mim]BF4的阳离子性质是影响阴离子表面活性剂过量区域性质的主要因素,IL通过静电作用、氢键作用等改变体系中聚集体的形貌,最终导致阴离子双水相(ATPSa)的消失。IL的阴离子对阳离子双水相(ATPSc)区域性质起着决定作用;IL的盐效应引起的对表面活性剂混合胶束扩散双电层的压缩作用,不但促进胶团的形成,缩短了形成稳定胶团所需要的时间,加快了双水相的相分离速度,而且也造成了形成ATPSc所需DTAB含量的提高。IL的引入改变了ATPSc上、下相表面活性剂的组成及含量,使富含表面活性剂的上相中阳离子表面活性剂含量更高,进而提高了双水相的萃取性能,其上相对甲基橙的萃取效率可高达96.67%。     

界面扩张流变法研究C_(12)mimBr对Gemini12-2-12在空气/水界面聚集行为的影响

采用界面扩张流变技术研究了季铵盐偶联表面活性剂C12-(CH2)2-C12·2Br(Gemini12-2-12)及其与离子液体表面活性剂溴化1-十二烷基-3-甲基咪唑(C12mim Br)复配体系的动态界面张力、扩张流变性质和界面弛豫过程等,探讨了C12mim Br对C12mim Br/Gemini12-2-12混合体系界面性质的影响及C12mim Br对Gemini12-2-12界面聚集行为影响的机制.结果表明,随着离子液体表面活性剂的不断引入,体系界面吸附达到平衡所需的时间逐渐缩短,扩张模量和相角明显降低,界面吸附膜由粘弹性膜转变为近似纯弹性膜;同时,界面及其附近的弛豫过程也发生显著变化,慢弛豫过程消失,快弛豫过程占主导地位,且离子液体浓度越高,快弛豫的贡献越大.这些界面性质的变化主要归因于离子液体表面活性剂C12mim Br参与界面形成及两表面活性剂在界面竞争吸附的结果.少量离子液体表面活性剂C12mim Br的加入可以填补疏松的Gemini12-2-12界面上的空位,形成混合界面吸附膜.随着C12mim Br含量的增加,嵌入界面的C12mim Br分子数不断增多,导致界面上相互缠绕的Gemini12-2-12烷基链"解缠",在体相和界面分子扩散交换的过程中"解缠"的Gemini12-2-12分子从界面上解吸回到体相,与此同时,C12mim Br分子相对较小的空间位阻及较强的疏水作用促使其优先扩散至界面进而取代Gemini12-2-12分子,最终界面几乎完全被C12mim Br分子所占据.     

环境因素对正负表面活性剂体系相行为的影响

在1:1正负离子表面活性剂混合体系(十二烷基硫酸钠/辛基三甲基溴化铵 SDS-C8NM3Br; 十二烷基硫酸钠/十二烷基三甲基溴化铵,SDS-C12NM3Br)中加入短链脂肪醇 (乙醇,正丙醇,正丁醇),正负离子表面活性剂沉淀溶解,出现表面活性剂双水相.上相有液晶存在,下相有囊泡自发形成.折光率数据和电镜结果表明:上相为表面活性剂富集相,下相表面活性剂浓度较低.混合体系中,出现表面活性剂双水相所需短链脂肪醇的体积百分数,随短链脂肪醇的链长增加而降低.温度升高,出现表面活性剂双水相所需短链脂肪醇的体积百分数降低.对SDS/C8NM3Br/H2O体系的研究结果表明:超声处理,可使混合体系中沉淀向囊泡转化,与短链脂肪醇的加入后的作用类似.     

DTAB-月桂酸钠体系表面活性剂双水相研究

绘制和分析了十二烷基三甲基溴化铵（DTAB） 月桂酸钠（SL）组成的表面活性剂混合体系相图,系统研究了温度和无机盐等因素对该体系表面活性剂双水相 (ASTP) 影响的规律性.结果表明:与富含负离子表面活性剂双水相 (ASTP A) 相比较,富含正离子表面活性剂双水相(ASTP C)区域更大、更稳定;温度升高,无机盐(NaBr)的浓度增大,都引起 ASTP 体系上相体积的减小和下相体积的增加;囊泡普遍存在于ASTP的上下相之中.     

离子液体表面活性剂1-丁基-3-甲基咪唑烷基硫酸酯的合成及其在水溶液中的聚集行为

采用离子交换法,由1-丁基-3甲基咪唑氯盐（C4mimCl）和烷基硫酸钠合成了一系列无卤素的阴离子表面活性离子液体—1-丁基-3-甲基咪唑烷基硫酸酯[C4mim][CnH2n 1SO4](n=8,12,16),利用表面张力仪、稳态荧光光谱等手段考察了表面活性离子液体在水溶液表面及体相中的聚集行为,结果表明,与传统无机反离子相比,有机咪唑阳离子[C4mim] 作为反离子的离子液体型表面活性剂具有较高的表面活性,[C4mim] 产生的氢键引起的抑制分子规则排列的作用小于其促进分子有序排列的疏水作用。长烷基链的阴离子是界面膜及胶束的主要组成成分,阴离子疏水烷基碳链的增长虽然可促进胶束的形成,但却在一定程度上抑制[C4mim] 离子参与界面或胶束的形成;阴离子所带烷基链越长,越不利于阳离子[C4mim]＋参与界面膜或胶束的形成,界面膜或胶束中表面活性剂排布越松散,即界面张力越大,体系中胶束聚集数较小。     

表面活性离子液体溴化N-十二烷基异喹啉与非离子表面活性剂Triton X-100在水溶液中的混合胶束

用等温滴定微量热法测定表面活性离子液体溴化N-十二烷基异喹啉([C₁₂iQuin]Br)与非离子表面活性剂Triton X-100混合物在水溶液中的临界胶束浓度。并以¹H核磁共振(NMR)和二维核Overhauser效应增强谱(2D NOESY)研究[C₁₂iQuin]Br与Triton X-100在混合胶束中的作用机理。研究结果显示：混合胶束中,Triton X-100分子的苯环定位于混合胶束的内核,聚氧乙烯链卷曲在异喹啉环周围。本文还应用规则溶液理论和浊点法对比研究了十二烷基三甲基溴化铵(DTAB)-Triton X-100混合胶束体系的相关性质。     

一种新的离子液体表面活性剂软模板法合成碳酸锶纳米棒

在室温下,以SrCl2·6H2O和(NH4)2Co3为原料,采用咪唑季铵盐离子液体表面活性剂1-十六烷基-3-甲基咪唑溴盐[C16 mim]Br软模板法制备了SrCO3纳米棒.利用透射电子显微镜(TEM)对产物进行了表征.初步探讨了SrCO3纳米棒的形成机理.结果表明SrCO3纳米棒长度在200nm左右,由平均直径为1...     

咪唑离子液体+1,2-丙二醇/1-丙醇二元体系在多温下的物理化学性质和超额性质

本文测定了温度288.15～333.15 K和常压下溴化1-己基/辛基-3-甲基咪唑离子液体([C_6mim]Br/[C_8mim]Br)+1,2-丙二醇/1-丙醇二元体系的密度(ρ)、折光率(nD)和黏度(η),计算获得了超额摩尔体积(V_m~E)和折光率偏差(Δn_D),并用Redlich-Kister方程对衍生性质数据进行拟合.密度、折光率和黏度值随组成的变化用多项式方程进行了拟合,讨论了醇、离子液体以及温度对二元体系物化性质的影响.     

C_(16)mimBr/Tween20混合胶团的聚集行为和热力学性质研究

通过测定表面张力,研究了离子液体型表面活性剂溴化1-十六烷基-3-甲基咪唑(C16mim Br)和非离子表面活性剂Tween20混合体系在水溶液中的聚集行为和热力学性质。利用Rubingh和Maeda模型计算了混合物中各组分在胶团相中的组成、相互作用参数以及胶团形成的热力学性质。结果表明,两组分在胶团形成过程中存在协同效应。非离子组分在胶团相中的组成高于本体溶液中的组成。分析和探讨了胶团形成的驱动力和稳定性。     

有机阳离子[C18mim]＋在蒙脱土层间的物理化学吸附与聚集状态*

咪唑基离子液体(N鄄十八烷基鄄N忆鄄甲基溴化咪唑盐[C18mim]Br)中的[C18mim]+可以通过离子交换反应进入蒙脱土层间.本文用TGA、FTIR和XRD 研究了[C18mim]+在蒙脱土层间的物理和化学吸附及其聚集状态. 研究结果表明, 蒙脱土存在着饱和的化学吸附量, 其总吸附量随物理吸附量的增加而增加；随着[C18mim]+在蒙脱土层间吸附量的增加, 其聚集态结构的有序性增加, 并伴有分子链的构象变化,导致层间距的增加.     

Conductivities, volumes, fluorescence, and aggregation behavior of ionic liquids [C4mim][BF4] and [C(n)mim]Br (n = 4, 6, 8, 10, 12) in aqueous solutions

Densities, conductivities, and polarity indexes of pyrene for aqueous solutions of a series of ionic liquids [C(n)mim]Br (n = 4, 6, 8, 10, 12) and [C4mim][BF4] have been determined at 298.15 K as a function of ionic liquid concentrations. It was shown that possible aggregation appeared for the ionic liquids in aqueous solutions except for [C4mim]Br. The critical aggregation concentration (CAC) of the ionic liquids, the ionization degree of aggregates (beta), the standard Gibbs energy of aggregation (Delta G(m)(o)), the limiting molar conductivity (Lambda(m)(o)), and the standard partial molar volume (V(m)(o)) for the ionic liquids were derived from the experimental data. The dependence of the CAC, Delta G(m)(o), Lambda(m)(o), and V(m)(o) on the length of the alkyl chain of the cations was examined. It was further suggested from volumetric data that a micelle was formed for [C8mim]Br, [C10mim]Br, and [C12mim]Br in aqueous solutions. Their apparent molar volumes at the critical micelle concentration (V Phi,CMC), apparent molar volumes in the micelle phase (V(Phi)(mic)), and the change of their apparent molar volume upon micellization (Delta V Phi,m) were calculated by application of the pseudophase model of micellization. In addition, the average aggregation number of [C(n)mim]Br (n = 8, 10, 12) has been determined by the steady-state fluorescence quenching technique, and predicted from a simple geometrical mode. It is found that the experimental values are in good agreement with the predicted ones.     

室温离子液体对氨基苯磺酸的萃取性能

系统研究了[C₄mim][PF₆], [C₆mim][PF₆], [C₆mim][BF₄]和[C₈mim][BF₄]室温离子液体对间氨基苯磺酸、对氨基苯磺酸稀水溶液的萃取平衡. 实验结果表明: 萃取温度和相体积比的变化对分配比影响不大; 水相pH值对萃取平衡有较大的影响, 氨基苯磺酸在离子液体/水体系中的分配比在pH＝4.2时达到最大值; 水相中CaCl₂或Na₂SO₄的存在能较大幅度地提高氨基苯磺酸的分配比; 离子液体的阴离子的性质对分配比有显著的影响, 阴离子为[BF₄]^－的离子液体对氨基苯磺酸的萃取能力大于阴离子为[PF₆]^－的离子液体; 咪唑环上烷基链的长度也对萃取效果有一定的影响. 在所研究的离子液体中, [C₆mim][BF₄]和[C₈mim][BF₄]对氨基苯磺酸有较好的萃取性能, 且萃取相中的氨基苯磺酸可回收利用, 离子液体也可循环使用.     

Ionic liquids enhanced oil recovery from oily sludge-experiment and mechanism

The oily sludge would cause environment pollution, and would cause the heavy oil waste. Therefore, it was vital for us to find novel methods to obtain heavy oil from the oily sludges. In this study, the [C₁₂mim][PF₆] and [C₁₂mim][Br] ionic liquids(ILs) were used to enhance the oil recovery. The toluene could obtain the highest oil recovery, and both the two ILs could increase the oil recovery. Toluene could obtain the highest oil recovery (89.4 wt%), and n-octane could obtain the lowest oil recovery (76.8 wt%). [C₁₂mim] [PF₆] could efficiently increase the heavy oil recovery to 91.2 wt%(by toluene). The [C₁₂mim][Br] could increase the heavy oil recovery further. Both the [C₁₂mim] [PF₆] and the [C₁₂mim][Br] ionic liquids could increase the heavy ois C/H ratio, decrease heavy oil viscosity and increase the sands hydrophilicity. The [C₁₂mim][Br] ionic liquids showed better effect. In addition, the ionic liquids could increase the solvents recovery, and the ionic liquids recovery were high. Therefore, the ionic liquids enhanced oil recovery could be recycled to ten times. The two ionic liquids could effectively decrease the heavy oil interaction force, and when the ionic liquids increased to 200 ppm, the force remained stable. In the end, the ionic liquids enhancing solvent extraction mechanism was put forward.     

Study on the Conductivities of Pure and Aqueous Bromide-Based Ionic Liquids at Different Temperatures

Electrical conductivities were measured for the pure ionic liquids [C₆mim][Br] (1-hexyl-3-methylimidazolium bromide) and [C₈mim][Br] (1-octyl-3-methylimidazolium bromide) at 0.1 MPa from 293.15 to 333.15 K. Conductivity measurements were also made for the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems and their ternary water + [C₆mim][Br] + [C₈mim][Br] system at 0.1 MPa and 293.15, 298.15, and 303.15 K. The conductivity data of the pure ionic liquids were correlated by the VFT (Vogel-Tamman-Fulcher) equation, and the fitting parameters and mean absolute deviations were determined. New explanations are presented for the molality-dependent behavior of the conductivity of the binary water + [C₆mim][Br] and water + [C₈mim][Br] systems. The generalized Young’s rule and the semi-ideal solution theory for conductivity were used to predict the conductivities of the ternary water + [C₆mim][Br] + [C₈mim][Br] system from the conductivities of its corresponding binary water + [C₆mim][Br] and water + [C₈mim][Br] subsystems. The predictions are in good agreement with the measured values.     

Nanostructural organization and anion effects in the optical Kerr effect spectra of binary ionic liquid mixtures

This article reports a study of the effect of anions on the optical Kerr effect (OKE) spectra of binary ionic liquid mixtures with one mixture comprising the 3-methyl-1-pentylimidazolium ([C 5mim] (+)) cation and the anions PF 6 (-) and CF 3CO 2 (-) (TFA (-)), and another mixture comprising the [C 5mim] (+) cation and the anions Br (-) and bis(trifluomethanesulfonyl)imide (NTf 2 (-)). The spectra were obtained by the use of optical heterodyne-detected Raman-induced Kerr Effect Spectroscopy at 295 K. The OKE spectra of the mixtures are compared with the calculated mole-fraction weighted sum of the normalized OKE spectra of the neat liquids. The OKE spectra are nearly additive for [C 5mim]Br/[C 5mim][NTf 2] mixtures, but nonadditive for [C 5mim][PF 6]/[C 5mim][TFA] mixtures. In the case of the equimolar [C 5mim][PF 6]/[C 5mim][TFA] mixture, the nonadditivity is such that the experimental OKE spectrum is narrower than the calculated OKE spectrum. The additivity or nonadditivity of OKE spectra for IL mixtures can be explained by assuming ionic liquids are nanostructurally organized into nonpolar regions and ionic networks. The ionic networks in mixtures will be characterized by "random co-networks" for anions that are nearly the same in size (PF 6 (-) and TFA (-)) and by "block co-networks" for anions that differ greatly in size (Br (-) and NTf 2 (-)).     

Effect of imidazolium-based ionic liquids on the aggregation behavior of twin-tailed cationic gemini surfactant in aqueous solution

Micellization behavior of the twin-tailed surfactants can be modulated by the addition of various modifiers. Ionic liquids (ILs) are one of them and are documented here. The beauty of these environmentally benign neoteric molecules lies in their structural versatility. Here, we have investigated the effect of three ILs: 1-butyl-3-methylimidazolium bromide ([C₄mim][Br]), 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]), and 1-octyl-3-methylimidazolium bromide ([C₈mim][Br]) on the aggregation and surface adsorption behavior of cationic gemini surfactant, bis(hexadecyldimethyl ammonium)propane dibromide (16-3-16) through experimentally measured electrical conductivities, surface tensions, and by spectral methods (UV-vis absorbance and fluorescence measurements). The main focus of the study is to observe the effect of added ILs on the critical micelle concentration (cmc), various surface parameters, aggregation number, and size of the aggregates of gemini surfactant. The results show that the more hydrophobic ILs, that is, [C₆mim][Br] and [C₈mim][Br] behave as electrolyte at lower concentration and cosurfactant at higher concentration, whereas moderately hydrophobic IL [C₄mim][Br] acts as an electrolyte at all concentration ranges studied. The modulating effects of ILs were also compared with conventional electrolyte (NaBr) at similar conditions.     

Nanostructural organization and anion effects on the temperature dependence of the optical Kerr effect spectra of ionic liquids

The intermolecular spectra of three imidazolium ionic liquids were studied as a function of temperature by the use of optical heterodyne-detected Raman-induced Kerr effect spectroscopy. The ionic liquids comprise the 1,3-pentylmethylimidazolium cation ([C(5)mim]+), and the anions, bromide (Br-), hexafluorophosphate (PF(6)-), and bis(trifluoromethanesulfonyl)imide (NTf(2)-). Whereas the optical Kerr effect (OKE) spectrum of [C(5)mim][NTf(2)] is temperature-dependent, the OKE spectra of [C(5)mim]Br and [C(5)mim][PF6] are temperature-independent. These results are surprising in light of the fact that the bulk densities of these room temperature ionic liquids (RTILs) are temperature-dependent. The temperature independence of the OKE spectra and the temperature dependence of the bulk density in [C(5)mim]Br and [C(5)mim][PF(6)] suggest that there are inhomogeneities in the densities of these liquids. The existence of density inhomogeneities is consistent with recent molecular dynamics simulations that show RTILs to be nanostructurally organized with nonpolar regions arising from clustering of the alkyl chains and ionic networks arising from charge ordering of the anions and imidazolium rings of the cations. Differences in the temperature dependences of the OKE spectra are rationalized on the basis of the degree of charge ordering in the polar regions of the RTILs.     

Impact of imidazolium-based ionic liquid surfactant additions on dilational rheology properties of different protein adsorption layer

The interfacial behavior of β-casein and BSA solutions have been investigated in the presence of imidazolium-based ionic liquid surfactant ([C₁₄mim]Br) at the decane/water interface with the oscillating the drop and interfacial tension relaxation measurements. Both the electrostatic and the hydrophobic interaction between protein and [C₁₄mim]Br played crucial roles as [C₁₄mim]Br concentration increases. Furthermore, it was found that the dilational rheology parameters provided information of the adsorbed layers structure, and the dynamics properties of the adsorbed layers depend on the bulk [C₁₄mim]Br concentration. Moreover, with the concentration of [C₁₄mim]Br increasing, β-casein in the interfacial layer was subject to conformational changes where it gave space to [C₁₄mim]Br molecules in the form of co-adsorb; for BSA/[C₁₄mim]Br solutions, the globule protein BSA deformed and then co-adsorb with [C₁₄mim]Br molecules at the decane/water interface. These results will contribute to elucidation of the influence of the surfactant on the different structure proteins and the wide applications of protein/surfactant systems in practice.