Mechanical properties and stability measurement of cholesterol-containing liposome on mica by atomic force microscopy

The micromechanical properties of pure and cholesterol modified egg yolk phosphatidylcholine (EggPC) vesicles prepared by sonication were studied by atomic force microscopy (AFM) on mica surface. The force curves between an AFM tip and an unruptured vesicle were obtained by contact mode. During approach, two repulsion regions with two breaks were observed. The slopes of the two repulsive force regimes for the pure EggPC vesicles are determined to be several times lower than that of EggPC/cholesterol vesicles. The elastic properties from force plot analysis based on the Hertzian model showed that Young's modulus (E) and the bending modulus (kc) of cholesterol-modified vesicles increased several-fold compared with pure EggPC vesicles. The significant difference is attributed to the enhanced rigidity of the EggPC vesicles as a result of the incorporation of cholesterol molecules. The behavior of cholesterol-modified vesicles upon adsorption is different from that in solution as revealed by mechanical properties. The results indicate that AFM can provide a direct method to measure the mechanical properties of adsorbed small liposomes and to detect the stability change of liposomes.     

Probing small unilamellar EggPC vesicles on mica surface by atomic force microscopy

Sonicated small unilamellar egg yolk phosphatidylcholine (EggPC) vesicles were investigated using atomic force microscopy (AFM) imaging and force measurements. Three different topographies (convex, planar, and concave shape) of the EggPC vesicles on the mica surface were observed by tapping mode in fluid, respectively. It was found that the topography change of the vesicles could be attributed to the interaction force between the AFM tip and vesicles. Force curves between an AFM tip and an unruptured vesicle were obtained in contact mode. During approach, two breaks corresponding to the abrupt penetration of upper and lower bilayer of vesicle were exhibited in the force curve. Both breaks spanned a distance of around 4 nm close to the EggPC bilayer thickness. Based on Hertz analysis of AFM approach force curves, the Young's modulus (E) and the bending modulus (kc) for pure EggPC vesicles were measured to be (1.97 +/- 0.75) x 10(6)Pa and (0.21 +/- 0.08) x 10(-19)J, respectively. The results show that the AFM can be used to obtain good images of intact and deformed vesicles by tapping mode, as well as to probe the integrity and bilayer structure of the vesicles. AFM force curve compare favorably with other methods to measure mechanical properties of soft samples with higher spatial resolution.     

Effect of aminoglycoside on mechanical properties of zwitterionic phospholipid vesicles

The effect of the aminoglycoside (streptomycin) incorporation on the nanomechanical properties of pure dipalmitoylphosphatidylcholine (DPPC) vesicles was studied using atomic force microscope (AFM) on mica surface. The vesicles were prepared by extrusion and adsorbed on the mica surface. The forces, measured between an AFM tip and the vesicle, presented that the breakthrough of the tip into the vesicles occurred two times. Each breakthrough represented each penetration of the tip into each bilayer. Force data prior to the first breakthrough were fitted well with the Hertzian model to estimate Young's modulus and bending modulus of the vesicles. It was found that the Young's modulus and bending modulus were not varied with the incorporation of AGs (streptomycins) up to the 1:1 AG/DPPC vesicle system. This result may suggest that the AGs do not lead to the disruption of DPPC packing.     

Elucidating driving forces for liposome rupture: external perturbations and chemical affinity

Atomic force microscopy (AFM) studies under aqueous buffer probed the role of chemical affinity between liposomes, consisting of large unilamellar vesicles, and substrate surfaces in driving vesicle rupture and tethered lipid bilayer membrane (tLBM) formation on Au surfaces. 1,2-Distearoyl-sn-glycero-3-phosphoethanolamine-N-poly(ethylene glycol)-2000-N-[3-(2-pyridyldithio) propionate] (DSPE-PEG-PDP) was added to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) vesicles to promote interactions via Au-thiolate bond formation. Forces induced by an AFM tip leading to vesicle rupture on Au were quantified as a function of DSPE-PEG-PDP composition with and without osmotic pressure. The critical forces needed to initiate rupture of vesicles with 2.5, 5, and 10 mol % DSPE-PEG-PDP are approximately 1.1, 0.8, and 0.5 nN, respectively. The critical force needed for tLBM formation decreases from 1.1 nN (without osmotic pressure) to 0.6 nN (with an osmotic pressure due to 5 mM of CaCl(2)) for vesicles having 2.5 mol % DSPE-PEG-PDP. Forces as high as 5 nN did not lead to LBM formation from pure POPC vesicles on Au. DSPE-PEG-PDP appears to be important to anchor and deform vesicles on Au surfaces. This study demonstrates how functional lipids can be used to tune vesicle-surface interactions and elucidates the role of vesicle-substrate interactions in vesicle rupture.     

Atomic force microscopy assisted immobilization of lipid vesicles

We report on a new approach to direct the immobilization of unilamellar lipid vesicles on substrate-supported lipid bilayers in a spatially confined manner. The adsorption of vesicles from solution is limited to areas of disorder in the bilayers, which is induced by scanning a pattern in situ with an atomic force microscopy (AFM) tip using high imaging forces. Lines of vesicles with a length exceeding 25 microm and a width corresponding to that of a single surface-immobilized vesicle have been fabricated. The adsorbed vesicles are effectively immobilized and do not desorb spontaneously. However, AFM with forces of several nanoNewtons allows one to displace vesicles selectively. The novel methodology described, which may serve as a platform for research on proteins incorporated in the lipid bilayers comprising the vesicles, does not require chemical labeling of the vesicles to guide their deposition.     

Atomic force microscopy studies of mesoscopic membranous bubbles on monolayers derived from SiCl3-terminated carbosilane dendrons on mica

Monolayers of dendrimers were prepared on mica by spin-coating of the second generation carbosilane dendrons with 9 SiCl(3) periphery groups. AFM images of the films showed the presence of soft yet robust, dome-shaped features with a base diameter of 100-2000 nm. The apparent height of the features, ranging from 10 to 200 nm, rapidly reduced under increasing compression force, eventually to the same value ( approximately 2.5 nm) corresponding to a bilayer of the flattened dendrons. The change in shape of the features in response to the compression force from the AFM tip was fully reversible, indicating that the features were robust. The contrast of the features in the tapping mode AFM (TMAFM) phase images flipped at a setpoint ratio of approximately 0.55. In contrast to the reported amplitude vs displacement (A/z) curves for compliant materials, A/z curves of the features showed that the reduction of amplitude was larger than the tip displacement as if the cantilever tip were repelled by the soft features. This result cautions the use of amplitude/phase vs displacement (APD) curves for interpreting TMAFM images and for optimizing conditions for TMAFM imaging of very soft and "sticky" surfaces. On the basis of the AFM studies, we believe that the dome-shaped features are membranous air bubbles. The membranes of the bubbles were probably composed of a bilayer of the dendron molecules bound through the peripheral silanol groups. The bilayer could be formed by self-assembly of the molecules on top of the air bubbles entrapped at the monolayer/solution interface during spin-coating.     

On the adhesion between fine particles and nanocontacts: an atomic force microscope study

In this study we measured the adhesion forces between atomic force microscope (AFM) tips or particles attached to AFM cantilevers and different solid samples. Smooth and homogeneous surfaces such as mica, silicon wafers, or highly oriented pyrolytic graphite, and more rough and heterogeneous surfaces such as iron particles or patterns of TiO2 nanoparticles on silicon were used. In the first part, we addressed the well-known issue that AFM adhesion experiments show wide distributions of adhesion forces rather than a single value. Our experiments show that variations in adhesion forces comprise fast (i.e., from one force curve to the next) random fluctuations and slower fluctuations, which occur over tens or hundreds of consecutive measurements. Slow fluctuations are not likely to be the result of variations in external factors such as lateral position, temperature, humidity, and so forth because those were kept constant. Even if two solid bodies are brought into contact under precisely the same conditions (same place, load, direction, etc.) the result of such a measurement will often not be the same as that of the previous contact. The measurement itself will induce structural changes in the contact region, which can change the value for the next adhesion force measurement. In the second part, we studied the influence of humidity on the adhesion of nanocontacts. Humidity was adjusted relatively fast to minimize tip wear during one experiment. For hydrophobic surfaces, no signification change in adhesion force with humidity was observed. Adhesion force versus humidity curves recorded with hydrophilic surfaces either showed a maximum or continuously increased. We demonstrate that the results can be interpreted with simple continuum theory of the meniscus force. The meniscus force is calculated based on a model that includes surface roughness and takes into account different AFM tip (or particle) shapes by a two-sphere model. Experimental and theoretical results show that the precise contact geometry has a critical influence on the humidity dependence of the adhesion force. Changes in tip geometry on the sub-10-nm length scale can completely change adhesion force versus humidity curves. Our model can also explain the differences between earlier AFM studies, where different dependencies of the adhesion force on humidity were observed.     

Influence of nanotopography on phospholipid bilayer formation on silicon dioxide

We have investigated the effect of well-defined nanoscale topography on the 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) lipid vesicle adsorption and supported phospholipid bilayer (SPB) formation on SiO2 surfaces using a quartz crystal microbalance with dissipation monitoring (QCM-D) and atomic force microscopy (AFM). Unilamellar lipid vesicles with two different sizes, 30 and 100 nm, were adsorbed on pitted surfaces with two different pit diameters, 110 and 190 nm, as produced by colloidal lithography, and the behavior was compared to results obtained on flat surfaces. In all cases, complete bilayer formation was observed after a critical coverage of adsorbed vesicles had been reached. However, the kinetics of the vesicle-to-bilayer transformation, including the critical coverage, was significantly altered by surface topography for both vesicle sizes. Surface topography hampered the overall bilayer formation kinetics for the smaller vesicles, but promoted SPB formation for the larger vesicles. Depending on vesicle size, we propose two modifications of the precursor-mediated vesicle-to-bilayer transformation mechanism used to describe supported lipid bilayer formation on the corresponding flat surface. Our results may have important implications for various lipid-membrane-based applications using rough or topographically structured surfaces.     

Effect of chain lengths of PEO-PPO-PEO on small unilamellar liposome morphology and stability: an AFM investigation

The morphology and stability of small unilamellar egg yolk phosphatidylcholine (EggPC) liposomes modified with the Pluronic copolymer (poly (oxyethylene)-poly (oxypropylene)-poly (oxyethylene) (PEO-PPO-PEO)) with different compositions on mica surface have been investigated using atomic force microscopy. Morphology studies reveal significant morphological changes of liposomes upon incorporating the Pluronic copolymer. Bilayers are observed for Pluronic with small hydrophilic (PEO) chain lengths such as L81 [(PEO)2(PPO)40(PEO)2] and L121 [(PEO)4(PPO)60(PEO)4]; bilayer and vesicle coexistence is observed for P85 [(PEO)26(PPO)39.5(PEO)26] and F87 [(PEO)61.1(PPO)39.7(PEO)61.1]; and stable vesicles are observed for F88 [(PEO)103.5(PPO)39.2(PEO)103.5], F127 [(PEO)100(PPO)65(PEO)100], and F108 [(PEO)132.6(PPO)50.3(PEO)132.6]. The micromechanical properties of Pluronic-modified EggPC vesicles were studied by analyzing AFM approaching force curve. The bending modulus (k(c)) of the Pluronic-modified EggPC vesicles increased several-fold compared with that of the pure EggPC vesicles. The significant difference is due to the enhanced rigidity of the EggPC vesicles as a result of the incorporation of PPO molecules and PEO chains. Based on the analysis of onset point by AFM and diameters of vesicles by light scattering, it was concluded that the favorable model to describe the polymer-bilayer interaction is the membrane-spanning model.     

Nanografting of alkanethiols by tapping mode atomic force microscopy

Nanografting, an atomic force microscopy (AFM) based nanolithography technique, is becoming a popular method for patterning self-assembled monolayers (SAMs). In this technique, a nanoscale patch of a thiol-on-gold SAM is exchanged with a different thiol by the action of an AFM tip operated in contact mode at high load. The results are then imaged in topographic or lateral force microscopy again at low values of the load. One of the problems of contact mode nanografting is that monolayers of large molecules such as proteins are likely to be deformed, damaged, or even removed from the surface by contact mode imaging even when small loads are used. Furthermore, we need to note that the stiffness of the cantilevers used in contact mode is different than that of the cantilevers used in tapping mode and that tip changing in the course of an experiment can be quite inconvenient. Here, we show that a monolayer on a gold substrate can be nanografted using tapping mode AFM (also referred to as amplitude modulation AFM) rather than the commonly used contact mode. While the grafting parameters are somewhat trickier to choose, the results demonstrate that nanografting in tapping mode can make patches of the same quality as those made by contact mode, therefore allowing for gentle imaging of the grafted molecules and the whole SAM without changing the microscope tip.     

Mechanical Properties of Poly(dimethylsiloxane)-block-poly(2-methyloxazoline) Polymersomes Probed by Atomic Force Microscopy

Poly(dimethylsiloxane)-block-poly(2-methyloxazoline) (PDMS-b-PMOXA) vesicles were characterized by a combination of dynamic light scattering (DLS), cryogenic transmission electron microscopy (cryo-TEM), and atomic force microscopy imaging and force spectroscopy (AFM). From DLS data, a hydrodynamic radius of ～150 nm was determined, and cryo-TEM micrographs revealed a bilayer thickness of ～16 nm. In AFM experiments on a silicon wafer substrate, adsorption led to a stable spherical caplike conformation of the polymersomes, whereas on mica, adsorption resulted also in vesicle fusion and formation of bilayer patches or multilayer stacks. This indicates a delicate balance between the mechanical stability of PDMS-b-PMOXA polymersomes on one hand and the driving forces for spreading on the other. A Young's modulus of 17 ± 11 MPa and a bending modulus of 7 ± 5 × 10(-18) J were derived from AFM force spectroscopy measurements. Therefore, the elastic response of the PDMS-b-PMOXA polymersomes to external stimuli is much closer to that of lipid vesicles compared to other types of polymersomes, such as polystyrene-block-poly(acrylic acid) (PS-b-PAA).     

Study on size growth in the vesicle formation upon detergent removal from phospholipid/ detergent mixed micelles

When 3-[(3-cholamidopropyl)dimethylammonio]-1-propane sulfonate (CHAPS) was removed from the mixed CHAPS/EggPC micelles, large vesicles were prepared by dialysis or by slow step-by-step dilution, but small vesicles were prepared by fast one-step dilution. When sodium cholate was removed from the sodium cholate/EggPC micelles, small vesicles formed either by dialysis or by dilution; however, in the presence of 5 mM Ca²⁺ large vesicles were produced by dialysis, while small vesicles were prepared by dilution. The size growth was related to a detergent-induced fusion of the vesicles containing a large amount of detergent. Using spectrophotometry, quasielastic light scattering and freeze–fracture electron microscopy the fusion events were investigated both through the process of vesicle solubilization by adding detergent and through the process of vesicle formation by diluting a mixed micelle. The results suggest that a rapid CHAPS-induced fusion of the vesicles led to the large resultant vesicles and that no fusion of vesicles containing sodium cholate is responsible for the formation of small vesicles. Furthermore, the ultimate vesicle size related to rapid or slow detergent removal is dependent on the kinetic aspects of the fusion. Received: 19 August 1999 Accepted: 18 February 2000     

Exocytosis of a single bovine adrenal chromaffin cell: the electrical and morphological studies

Exocytosis of a single bovine adrenal chromaffin cell, triggered by histamine stimulation, was investigated via the electric responses detected with single-walled carbon-nanotube field-effect transistors (SWCNT-FET) and the morphological changes acquired by atomic force microscopy (AFM). Secretion of chromogranin A (CgA), stored in the vesicles of a single chromaffin cell, can be monitored in situ by the antibody against CgA (CgA-antibody) functionalized on the SWCNT-FET devices. The SWCNT-FET can further discriminate the amount of released CgA with different levels of histamine stimulations. The AFM morphological studies on a chromaffin cell indicate that the depression structures on the cell surface, caused by the histamine-evoked exocytotic fusion pores, appeared much more frequently than those without histamine stimulation or with the pretreatment of mepyramine before histamine stimulation. The vesicle diameters are about 50 nm calculated from the obtained three-dimensional AFM images. In comparison, the fusion pores of chromaffin cells stimulated by high-K (+) buffer solution were also investigated to have a wider-ranging distribution of vesicle diameters of 60-260 nm. This work demonstrates that the combination of novel techniques, SWCNT-FET and AFM, can provide further insights into the fundamental properties of exocytosis in neuroendocrine cells.     

Oxidation‐induced the Formation of Vesicles from Ferrocene Derivative Superamphiphiles

The stimuli‐responsive vesicles were prepared via electrochemical oxidation on the mixture solution of ferrocenylmethyl‐trimethylammonium iodide (FcMI) and sodium deoxycholate (NaDC). The vesicle structure and morphology are characterized respectively by transmission electron microscopy (TEM), dynamic light scattering (DLS) and atomic force microscopy (AFM). The vesicle shells can be clearly observed by TEM with the thickness ranging from several to several tens of nanometers and their outer diameters at the range of 50‐200 nm. The formation of vesicular structures is also supported via AFM measurements, and the ratio of the diameter and height of the nanospheres was estimated to be ca. 10, indicating the shell collapse. The obtained results are significant for the preparation of smart supramolecular aggregates.     

Patterns of surface immobilized block copolymer vesicle nanoreactors

The immobilization and positioning of ultra small reaction vessels on solid supports open new pathways in applications such as lab-on-a-chip, sensors, microanalyses and microreactors. In our work block copolymer vesicles made from polystyrene-block-polyacrylic acid (PS-b-PAA) were immobilized from aqueous medium onto 3-amino propyl trimethoxysilane functionalized silicon surfaces exploiting electrostatic interactions. The immobilization of the vesicles was investigated by Fourier transform infrared (FTIR) spectroscopy, as well as fluorescence optical and atomic force microscopy (AFM). In addition, the influence of pH and ionic strength on the surface coverage of vesicles bound to the surface was elucidated. Finally micro-molding in capillaries (MIMIC) was utilized to create line patterns of the vesicles containing the enzyme trypsin and the fluorogenic substrate rhodamine 110 bisamide. The selective positioning of vesicle nanoreactors in conjunction with electrostatic immobilization serves as a proof of principle for potential applications in real-time observation of confined chemical reaction inside vesicles as nanocontainers and for the fabrication of integrated microarray systems.     

Measurement of polyamide and polystyrene adhesion with coated-tip atomic force microscopy

This work presents atomic force microscopy (AFM) measurements of adhesion forces between polyamides, polystyrene and AFM tips coated with the same materials. The polymers employed were polyamide 6 (PA6), PA66, PA12 and polystyrene (PS). All adhesion forces between the various unmodified or modified AFM tips and the polymer surfaces were in the range -1.5 to -8 nN. The weakest force was observed for an unmodified AFM tip with a PS surface and the strongest was between a PS-coated tip and PS surface. The results point to both the benefits and drawbacks of coated-tip AFM force-distance measurements. Adhesion forces between the two most dissimilar (PA6-PS and PA66-PS) materials were significantly asymmetric, e.g., the forces were different depending on the relative placement of each polymer on the AFM tip or substrate. Materials with similar chemistry and intermolecular interactions yielded forces in close agreement regardless of placement on tip or substrate. Using experimental forces, we calculated the contact radii via four models: Derjaguin, Muller, and Toporov; Johnson, Kendall, and Roberts; parametric tip-force-distance relation; and a square pyramid-flat surface (SPFS) model developed herein. The SPFS model gave the most reasonable contact tip radius estimate. Hamaker constants calculated from the SPFS model using this radius agreed in both magnitude and trends with experiment and Lifshitz theory.     

原子力显微镜研究囊泡在云母表面形成的结构

The vesicle structures of egg yolks phosphatidylcholine/didodecyldimethylammonium bromide （1 ： 1, mass ratio） deposited on mica were studied by atomic force microscopy （AFM） both in aqueous phase and air. In aqueous phase both bilayer and domelike vesicles with a mean diameter of 45 nm were observed, whereas in air the structure was more complicated depending on the initial concentration of vesicles. Vesicles with the original size could only be visualized at very low concentration with a mean diameter of 55 nm, which is a little larger than the result obtained in aqueous phase. At higher concentrations, fused large aggregates and multiple bilayer with a thickness ca. 4 nm of each bilayer were dominated. A plausible adsorption mechanism was proposed based on the experimental results.     

Sequential electrochemical oxidation and site-selective growth of nanoparticles onto AFM probes

In this work, we reported an approach for the site-selective growth of nanoparticle onto the tip apex of an atomic force microscopy (AFM) probe. The silicon AFM probe was first coated with a self-assembled monolayer (SAM) of octadecyltrichlorosilane (OTS) through a chemical vapor deposition (CVD) method. Subsequently, COOH groups were selectively generated at the tip apex of silicon AFM probes by applying an appropriate bias voltage between the tip and a flat gold electrode. The transformation of methyl to carboxylic groups at the tip apex of the AFM probe was investigated through measuring the capillary force before and after electrochemical oxidation. To prepare the nanoparticle terminated AFM probe, the oxidized AFM probe was then immersed in an aqueous solution containing positive metal ions, for example, Ag+, to bind positive metal ions to the oxidized area (COOH terminated area), followed by chemical reduction with aqueous NaBH 4 and further development (if desired) to give a metal nanoparticle-modified AFM probe. The formation of a metal nanoparticle at the tip apex of the AFM probe was confirmed by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDXA).     

Distribution of olfactory marker protein on a tissue section of vomeronasal organ measured by AFM

Distribution of olfactory marker protein (OMP) on a tissue section of vomeronasal organ (VNO) was successfully measured by atomic force microscopy (AFM). Anti-OMP antibodies were covalently crosslinked with the tip of the AFM and were used as a probe to observe the distribution of OMP on a tissue section. First, force measurements were performed using a glass surface on which OMP was covalently immobilized to verify the success of tip modification. Clear differences of interaction forces were observed between a specific pair and the control experiments, indicating that the tip preparation succeeded. Next, distributions of OMP on the tissue section were observed by AFM and were compared with immunohistochemical observations. For large scale observation, a microbead was used as a probe in the AFM measurements. The results of the AFM measurements were well overlapped with that of immunohistochemistry, confirming the reliability of our method. A mapping of the AFM measurement with high resolution was also successfully obtained, which showed an advantage of the application of the AFM measurement in analysis of proteins on the tissue section.     

Salt-induced vesicle to micelle transition in aqueous solution of sodium N-(4-n-octyloxybenzoyl)-L-valinate

The self-organization of a single-tailed amino acid based chiral surfactant sodium N-(4-n-octyloxybenzoyl)-L-valinate (SOBV) has been studied in water. A number of techniques like surface tension, fluorescence probe, dynamic light scattering (DLS), transmission electron microscopy (TEM), and atomic force microscopy (AFM) have been utilized for characterization of the self-assemblies. The amphiphile forms large spherical vesicles of 400-600 nm diameters in dilute aqueous solution. However, the vesicles get transformed into spherical micelles with increase of surfactant concentration or upon addition of relatively low amount (20 mM) of NaCl or KCl. This is the first example of salt-induced vesicle to micelle transition (VMT) in a single surfactant system. The vesicles are stable in the temperature range of 30-70 degrees C. Cleavage of intermolecular hydrogen bonds among the amide groups in the presence of salt appears to be the plausible cause for the VMT.