Pecularities of the thermomechanical behaviour of ultra-high molecular weight linear polyethylene and its blends with linear polyethylene of normal molecular weight

Ultra-high molecular weight polyethylene UHMWPE (M _w=4 · 10⁶,I _s=O g/ 10 min), high density polyethylene of normal molecular weight NMWPE (I _s= 4.8 g/10 min) and their blends have been investigated by means of thermomechanical loading in constant and impulse regime. It has been established that after melting, NMWPE passes to a viscous-liquid state. After melting at 138 °C UHMWPE passes to a high-elastic state. The transition of UHMWPE to a viscous-liquid state takes place at temperatures higher than 180 °C and is accompanied by a high-elastic reversible deformation. The blends of UHMWPE with 10 and 20 mass % of NMWPE show a plateau on the thermomechanical curves, corresponding to a high-elastic state, in a shorter temperature range where the deformation is greater. The blends containing the higher percent of NMWPE show thermomechanical curves lacking such a plateau. All blends are characterized by a singular thermomechanically defined temperature of melting, which increases with increase of UHMWPE content. The existence of the high-elastic state in the curves of UHMWPE and its blends containing NMWPE less than 30 mass % above their melting temperatures is explained by the high degree of physical crosslinking of UHMWPE.     

Optimization of molar content of amidoxime and acrylic acid in UHMWPE fibers for improvement of seawater uranium adsorption capacity

Ultra-high molecular weight polyethylene (UHMWPE) fibrous adsorbents with different molar content of amidoxime (M _AO) and acrylic acid (M _AA) were prepared by graft polymerization of acrylonitrile (AN) and acrylic acid (AA), followed by amidoximation. Uranium adsorption experiments in both artificial and natural seawater were carried out to investigate the effect of M _AO and M _AA on the uranium adsorption capacity of UHMWPE fibrous adsorbents. Adsorption results showed that the UHMWPE fibrous adsorbent with M _AO = 4.27 and M _AA = 4.64 mmol/g-ads exhibited better uranium adsorption capacity in both artificial (7.01 mg-U/g-ads) and natural (0.77 mg-U/g-ads) seawater.

     

Surface oxidation of rubber crumb with ozone

Rubber crumb derived from the grinding of used truck tread and tyres is used as a low cost filler in rubber compounds based on diene rubber. In order to expand its application to other fields, the surface modification of the rubber crumb could be an interesting and feasible solution. In fact, the surface modification of rubber crumb may be used as a tool to expand its use in applications to compounds with polar rubber matrices or where hydrophilic surface of the rubber crumb could be desirable, for example in water-based dispersion or as filler for asphalt. In the present work, ozone has been used as the active agent to cause surface oxidation and functionalisation of rubber crumb in a fluidized bed reaction. The rubber crumb reacts swiftly with ozone producing CO₂ in the initial stages of reaction and then leading to the desired surface oxidized product. The rate constant of the reaction between ozone and rubber crumb has been determined by FT-IR spectroscopy, monitoring the consumption of ozone in the gas phase in the presence of the crumb. A rate constant value of 5.03 × 10⁻³ s⁻¹  g⁻¹ of rubber crumb was determined. The degree of the surface oxidation of the rubber crumb can be determined by FT-IR spectroscopy using as reference the intensity of the ketone band at about 1710 cm⁻¹. Additionally the nominal ratio between the amount of ozone (in mg) reacted with rubber crumb (in g) can be used as a parameter for the degree of the surface oxidation. The surface oxidized rubber crumb shows surface acidity and hydrophilicity. Thermogravimetric analysis, differential thermal analysis and pyrolysis-GC clearly demonstrate that the ozonization of the rubber crumb is directed exclusively to the surface of the crumb and does not affect the bulk properties at all.     

Tensile strength of highly oriented polyethylene. II. Effect of molecular weight distribution

The tensile strength of oriented polyethylene filaments is discussed in relation to molecular weight. Short-term tensile properties at room temperature were obtained in our laboratory and from the literature for polymer samples covering the molecular weight (M _w) range from 54 × 10³ to 4 × 10⁶, and polydispersities ranging from 1.1 to 15.6, oriented by solid-state extrusion, melt spinning/drawing, solution spinning/drawing, and “surface growth.” It was found that both the molecular weight and its distribution markedly affected tensile strength. The breaking stress σ of highly oriented fibers varied with molecular weight roughly as σ ∝, M^0.4, at constant M _w/M _n over the entire range studied. Reduction of polydispersity from 8 to 1.1 by an increase of M _n with M _w approximately constant at 10⁵ increased tensile strength of oriented polyethylene filaments by a factor of nearly 2.     

Synthesis, characterization and thermal degradation of oligo-2-[(4-fluorophenyl) imino methylene] phenol and some of its oligomer-metal complexes

In this study, the oxidative polycondensation reaction conditions of 2-[(4-fluorophenyl) imino methylene] phenol (FPIMP) with air oxygen and NaOCl were studied in an aqueous alkaline medium between 60 and 90 °C. Synthesized oligo-2-[(4-fluorophenyl) imino methylene] phenol was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. The yield of oligo-2-[(4-fluorophenyl) imino methylene] phenol (OFPIMP) was found to be 62.00% (for air O₂ oxidant) and 97.70% (for NaOCl oxidant) at the optimum reaction conditions. According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of OFPIMP were found to be 1370 g mol⁻¹, 1979 g mol⁻¹ and 1.45, using NaOCl, 2105 g mol⁻¹, 2557 g mol⁻¹, and 1.22, using air O₂, respectively. During the oxidative polycondensation reaction, (2.88%) a part of -CHN group oxidized to carboxylic acid (-COOH). TG and TG-DTA analyses were shown to be more stable of oligo-2-[(4-fluorophenyl) imino methylene] phenol and its oligomer metal complexes than monomer against thermo-oxidative decomposition. The weight loss of OFPIMP was found to be 97.00% at 900 °C. The weight losses of OFPIMP-Co, OFPIMP-Ni OFPIMP-Cu oligomer-metal complex compounds were found to be 88.66%, 94.36% and 83.21%, respectively, at 1000 °C.     

Real-time X-ray scattering study during heating of oriented injection-molded polyethylene

Highly oriented linear polyethylene was prepared by elongational flow injection molding. The changes in crystal orientation were investigated as a function of temperature by real-time wide-angle X-ray diffraction. Additionally, the influence of molecular weight upon the microstructure and the changes in orientation, during heating near the melting point, and after cooling have been examined. A shish-kebab structure is inferred for the high molecular weight samples (M_w≥10⁵) from SAXS observations, while for samples with M_w<10⁵ only an oriented lamellar structure is found. Consequently, a higher thermal stability is shown by the higher molecular weight samples. Furthermore, a recovery of crystal orientation on rapid cooling of the samples from the melt is only observed for samples with M_w≥10⁵. The results are discussed in terms of a preferential recrystallization of chain-folded lamellae, on cooling, onto the shish fibrils which survive at high temperature.     

Synthesis, characterization, and ethylene polymerization behavior of [(RR′-admpzp)2Ti(OPr)2] complexes (RR′-admpzp = 1-dialkylamino-3-(3,5-dimethyl-pyrazol-1-yl)-propan-2-olate)

[(RR′-admpzp)₂Ti(OPrⁱ)₂] complexes (2a-c), synthesized from reaction of Ti(OPrⁱ)₃Cl (0.5 equiv) with 1-dialkylamino-3-(3,5-dimethyl-pyrazol-1-yl)-propan-2-ol compounds in the presence of triethylamine (0.5 equiv), are pseudo-octahedral with each RR′-admpzp ligand κ²-O,N(pyrazolyl) coordinated to the titanium center. In solution, 2a-c adopt isomeric structures that are in dynamic equilibrium. At 23 °C, 2a-c/1000 MAO catalyst systems furnished high molecular weight polymers with narrow molecular weight distributions (M_w/M_n = 2.7-2.8). At 100 °C, 2a-c/MAO catalyst systems exhibited increased polymerization activity and 2c/1000 MAO system furnished high molecular weight polyethylene with a molecular weight distribution (M_w/M_n = 2.1) that is close to that found for single-site catalysts.     

Enhanced surface free energy of UHMWPE fibers and its interfacial adhesion behavior to PI resins

Mechanical properties of composites made up of ultra‐high‐molecular‐weight polyethylene (UHMWPE) fiber, polyimide (PI), and TiO₂ particles were investigated. The hybrid composite of 20 vol% of UHMWPE fiber with TiO₂ showed tensile strength greater than UHMWPE fiber/PI composite. A positive hybrid effect in tensile strength is obtained. It is observed that addition of small amount of TiO₂ to UHMWPE fiber/PI increased the tensile strength of the composite by 28%. With increase in TiO₂ loading to 1 to 3 vol%, the impact strength of the hybrid composite is increased from 55 KJ/m² to 69 KJ/m². This maximum value is more than one and a half times greater than the impact strength of neat UHMWPE fiber/PI composite.     

Influence of the particle size of the MgCl2 support on the performance of Ziegler catalysts in the polymerization of ethylene to ultra‐high molecular weight polyethylene and the resulting polymer properties

A highly systematic size series of Ziegler catalysts with similar porosities and surface textures are synthesized by varying the stirring speed during the MgCl₂ support synthesis. Besides the mean particle size, the only substantial difference observed between the various catalysts is the size and number of nodules per particle. Varying the mean diameter of the catalyst particles between 1.5 and 11.9 µm, leads to a pronounced impact on the activity in ultra‐high molecular weight polyethylene (UHMWPE) polymerization, while the M_w capabilities are only affected to a limited extend. In addition, it is observed that both the M_ws as the polymer bulk density (BD) increases during the course of the polymerization. This particularity allows to optimize the M_w and/or BD at a set polymer size, by tuning the catalyst particle size. This is particularly interesting in UHMWPE production, as control of the morphological and structural properties of the UHMWPE reactor powders are critical for efficient processing as well as the performance of the final product. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2679–2690     

Formation of regular clusters through self-association of intramolecularly hypercrosslinked polystyrene-type nanosponges

Atactic polystyrene of M = 330,000 Da and M_w/M_n = 1.04 was subjected to chloromethylation. By the heating of chloromethylpolystyrene with SnCl₄ in a very dilute solution in ethylene dichloride, the polymeric coils were converted into intramolecularly hypercrosslinked macromolecules, nanosponges, of molecular weight of about 370,000 Da and a diameter of about 17 nm. When in solution, the nanosponges tend to reversibly self-assemble into regular clusters. Size exclusion chromatography and sedimentation analysis corroborate the suggestion that the clusters consist of 13 spherical subunits and thus acquire a molecular weight of about 5.0 × 10⁶ Da and a diameter of about 45 nm. © John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3847–3852, 1997     

Determination of carboxyl content in carboxylated nitrile butadiene rubber (XNBR) after degradation via olefin cross metathesis

Carboxyl content in nitrile butadiene rubber (XNBR) has an impact on its application performance. However, its poor solubility makes it difficult to determine the carboxyl content in XNBR due to its high molecular weight. In the present work, olefin cross metathesis was used to degrade XNBR with acrylonitrile (AN) as chain transfer agent for the first time, to solve the solubility problem. After degradation under the optimized condition, with 2% AN and 0.2% catalyst at 60 °C for 30 min, the weight-average molecular weight (M_w) of the product decreased to 0.98 × 10⁴ with distribution (M_w/M_n) of 3.83. Such product was easy to be dissolved, so the carboxyl content in XNBR could be determined with the routine titrimetric analysis methods.     

Kinetics and mechanism of dissolved organic phosphorus (DOP) digestion by the UV/O3 process

In this study, the kinetics and mechanism of UV/O₃ synergistic oxidative digestion of dissolved organic phosphorus (DOP) were investigated, focusing on the ozone direct oxidation and hydroxyl radical oxidation parts of glufosinate and triphenyl phosphate (TPhP). The p-chlorobenzoic acid (p-CBA) was selected as the probe compound, and two kinds of reaction kinetic models were proposed by competitive kinetic method with R_ct according to the different scale of rate constants of hydroxyl radical oxidation. Under the condition of weakly alkaline (pH = 9.0) and weakly acidic environment (pH = 5.0), the second-order rate constants of glufosinate and TPhP was determined indirectly to be ko_{3/glufosinate} = (2.903 ± 0.247)M⁻¹s⁻¹ and ko_3/TPhP = (3.307 ± 0.204) M⁻¹s⁻¹ by ozone direct oxidation, and k_{·OH/glufosinate} = (1.257 ± 1.031) × 10⁹ M⁻¹s⁻¹ and k_·OH/TPhP = (7.120 × 10⁸ ± 0.963) M⁻¹s⁻¹ by hydroxyl radical oxidation, respectively. The comparison of the contribution levels of the two parts to the digestion process showed that the contribution levels in the digestion of glufosinate and TPhP processes both the contribution of ·OH were higher than those of ozone, 86.3% and 72.6%, respectively.     

Direct construction of silicon-silicon bond by using the low-valent titanium reagent

The reductive dimerization or polymerization of organochlorosilanes has been achieved by using the low-valent titanium reducing agent other than the alkali metals that are invariable used in the Wurtz-type coupling reaction. Applying this method, the corresponding disilanes or poly(methylvinylsilane) was obtained in good yields. The poly(methylvinylsilane) synthesized by this method is highly pure with a high molecular weight and a narrow molecular weight distribution (M_w/M_n = 1.6, M_n = 16,860).     

Ultrasonic energy as a tool in the sample treatment for polymer characterization through matrix-assisted laser desorption ionization time-of-flight mass spectrometry

Different ultrasonic devices including ultrasonic bath with dual frequency, sonoreactor and ultrasonic probe, were tested for their viability in the sample treatment for polymer characterization by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry analysis. The effect of sonication frequency (35 kHz, 40 kHz and 130 kHz), sonication amplitude, and sonication time on the polymer's number-average molecular weight (M_n) and weight-average molecular weight (M_w) were investigated. The effect of those variables in the molecular mass distribution of three polymer standards, poly(styrene) 2000 Da and 10,000 Da and poly(ethylene glycol) 1000 Da, was evaluated. In addition, the influence of ultrasonic energy on the sample treatment as a function of the matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI) matrix was also studied through two common standard matrices, dithranol and 2,5-dihydroxybenzoic acid. The results obtained show that the ultrasonic bath at 35 kHz is the best option for the purpose of fast sample treatment for polymer characterization. The M_n and M_w values obtained for this ultrasonic device and for the three polymers tested using dithranol as MALDI matrix, were not statistically different from the ones acquired with vortex mixing and also were in concordance with the values recommended by the polymer manufacturers.     

Living radical graft polymerization of methyl methacrylate to polyethylene film with typical and reverse atom transfer radical polymerization

Nickel‐mediated atom transfer radical polymerization (ATRP) and iron‐mediated reverse ATRP were applied to the living radical graft polymerization of methyl methacrylate onto solid high‐density polyethylene (HDPE) films modified with 2,2,2‐tribromoethanol and benzophenone, respectively. The number‐average molecular weight (M_n) of the free poly(methyl methacrylate) (PMMA) produced simultaneously during grafting grew with the monomer conversion. The weight‐average molecular weight/number‐average molecular weight ratio (M_w/M_n) was small (<1.4), indicating a controlled polymerization. The grafting ratio showed a linear relation with M_n of the free PMMA for both reaction systems. With the same characteristics assumed for both free and graft PMMA, the grafting was controlled, and the increase in grafting ratio was ascribed to the growing chain length of the graft PMMA. In fact, M_n and M_w/M_n of the grafted PMMA chains cleaved from the polyethylene substrate were only slightly larger than those of the free PMMA chains, and this was confirmed in the system of nickel‐mediated ATRP. An appropriate period of UV preirradiation controlled the amount of initiation groups introduced to the HDPE film modified with benzophenone. The grafting ratio increased linearly with the preirradiation time. The graft polymerizations for both reaction systems proceeded in a controlled fashion. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3350–3359, 2002     

Chiral linear polymers bonded alternatively with salen and 1,4-dialkoxybenzene: synthesis and application for Ti-catalyzed asymmetric TMSCN addition to aldehydes

The synthesis of chiral linear polymers 1a–b having salen and 1,4-dioctyloxybenzene as alternate segments has been accomplished. The GPC analysis showed the molecular weights corresponding to ca. 15 (M_w = 10,999, M_n = 9165 and PDI = 1.20) repeating units for 1a and ca. 8 (M_w = 8547, M_n = 7883 and PDI = 1.08) repeating units for 1b. Polymers 1a–b have been studied with Ti(OⁱPr)₄ as a recyclable catalyst for the asymmetric addition of TMSCN to aldehydes while the selectivity of the polymer catalyst is identical to that of the monomer. The reactions are efficient affording the cyanohydrins with up to 88% ee. The selectivity of the polymer based catalyst 9a is found to be the same to that of the monomer 10a. The reaction provides the advantages of simplified product isolation and easy recovery and recyclability of polymer catalyst 9a without any loss of activity or selectivity.     

Enhancement of plant growth stimulation activity of irradiated alginate by fractionation

Alginate with the weight-average molecular weight (M_w) approximately 900 kDa and ratio of M (mannuronate)/G (guluronate) about 1.3 was irradiated by gamma Co-60 in aqueous solution at doses up to 200 kGy. The irradiation dose was shown to be a function for reducing M_w and molecular weight distribution of irradiated alginates. The distribution of oligomer fractions in irradiated products was also investigated by separation using ultrafiltration membranes. The irradiated alginate with M_w approximately 14.2 kDa was found to have a positive influence for growing of barley and soybean. The irradiated oligoalginate fraction with M_w ranging from 1 to 3 kDa displayed the strongest effect on the growth and development of the mentioned plants at low concentration (20 ppm). It is suggested that oligoalginate with M_w in the range 1–3 kDa is a trigger for the growth and development of plants.     

Preparation of Polyester Polyol from Epoxidized Palm Olein

In this work, polyester polyols with high weight average molecular weight (M_w) (M_w?10000–15000) were prepared from epoxidized palm olein (EPO_o) and a series of dicarboxylic acids (C₆–C₁₂) at elevated temperature under non‐catalyzed condition. The optimal reaction conditions were determined as 180°C for 4 h. Longer carbon chain length of dicarboxylic acids was more reactive when reacted with EPO_o. The physical appearance of the product was observed as liquid at room temperature. This palm oil‐based polyester polyol is proposed as starting material for flexible polyurethane. For reaction monitoring purposes, FTIR was used while ¹H NMR analysis was carried out to characterize the important functional groups of the products. The effects of reaction time and temperature on the M_w of the reaction mixture were also studied by GPC.     

Synthesis and characterization of phosphorous-bridged bisphenoxy titanium complexes and their application to ethylene polymerization

Phosphorous-bridged bisphenoxy titanium complexes were synthesized and their ethylene polymerization behavior was investigated. Bis[3-tert-butyl-5-methyl-2-phenoxy](phenyl)phosphine tetrahydrofuran titanium dichloride (4a) was obtained by treatment of 3 equiv of n-BuLi with bis[3-tert-butyl-2-hydroxy-5-methylphenyl](phenyl)phosphine hydrochloride salt (3a) followed by TiCl₄(THF)₂ in THF. THF-free complexes 5a-5d were synthesized more conveniently by the direct reaction of MOM-protected ligands (2a-2d) with TiCl₄ in toluene. X-ray analysis of 4a revealed that the ligand is bonded to the octahedral titanium (IV) center in a facial fashion and two chlorine atoms possess cis-geometry. Complexes 4a and 5a-5d were utilized as catalyst precursors for ethylene polymerization. Complex 5c gave high molecular weight polyethylene (M_w = 1,170,000, M_w/M_n = 2.0) upon activation with Al(ⁱBu)₃/[Ph₃C][B(C₆F₅)₄] (TB). Ethylene polymerization activity of 5d activated with Al(ⁱBu)₃/TB reached 49.0 × 10⁶ g mol (cat) ⁻¹ h⁻¹.     

ROMP of t-butyl-substituted ferrocenophanes affords soluble conjugated polymers that contain ferrocene moieties in the backbone

A substituted ferrocenophane, 1,1′-((1-tert-butyl)-1,3-butadienylene)ferrocene, was synthesized and polymerized via ring-opening metathesis polymerization (ROMP) to give soluble high molecular weight polymers with ferrocenylene units in the backbone. The monomer readily underwent polymerization upon exposure to a tungsten-based metathesis initiator, W(CHC₆H₄-o-OMe)(NPh)[OCMe(CF₃)₂]₂ (THF), to give high molecular weight polymers (M_w=ca. 300,000). The molecular weights could be varied systematically by adjusting the monomer-to-catalyst ratio. UV/vis spectra revealed a bathochromic shift for the polymer, consistent with enhanced conjugation compared to the monomer. The polymer exhibited thermal properties similar to oligomeric poly(ferrocenylene). Cyclic voltammetry of the polymer suggested that the iron centers are coupled electronically. Upon doping with I₂ vapor, the polymers displayed semiconducting properties (σ=10⁻⁵ S cm⁻¹). Theoretical calculations were used to evaluate the nature of the bonding in these and related polymers.